Whirlpool WCD3090JW Manuel utilisateur

W11389806D

If you have any problems or questions, visit us at www.whirlpool.com

Pour tout problème ou toute question, consulter www.whirlpool.ca

Owner’s Manual

Guide d’utilisation

Condensing Dryer

Sécheuse à condensation

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.whirlpool.com.

2

DRYER SAFETYDRYER SAFETY

Table of Contents

DRYER SAFETY ......................................................................2

OPERATING INSTRUCTIONS ............................................... 3

ACCESSORIES ................................................................. 3

CONDENSER DRYER TECHNOLOGY .............................4

CONTROL PANEL AND FEATURES .................................5

PROGRAM/CYCLE GUIDE ............................................... 6

USING YOUR DRYER .......................................................8

DRYER CARE .................................................................11

INSTALLATION INSTRUCTIONS ........................................ 13

INSTALLATION REQUIREMENTS ..................................13

LOCATION REQUIREMENTS .........................................14

DRAIN SYSTEM ..............................................................15

ELECTRICAL REQUIREMENTS – U.S.A. ONLY ............. 16

ELECTRIC DRYER POWER HOOKUP –

CANADA ONLY ...............................................................17

ELECTRIC INSTALLATION – U.S.A. ONLY ...................17

LEVEL DRYER ................................................................23

COMPLETE INSTALLATION CHECKLIST ......................23

DOOR REVERSAL (OPTIONAL) ......................................24

TROUBLESHOOTING ...........................................................29

ASSISTANCE OR SERVICE ..................................Back Cover

Table de matières

SÉCURITÉ DE LA SÉCHEUSE .............................................31

INSTRUCTIONS D’UTILISATION ........................................ 32

ACCESSOIRES ............................................................... 32

TECHNOLOGIE DE SÉCHEUSE À CONDENSATION ....33

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ...34

GUIDE DE PROGRAMMES ............................................35

UTILISATION DE LA SÉCHEUSE ...................................39

ENTRETIEN DE LA SÉCHEUSE......................................42

INSTRUCTIONS D’INSTALLATION .................................... 44

EXIGENCES D’INSTALLATION.......................................44

EXIGENCES D’EMPLACEMENT .....................................45

SYSTÈME DE VIDANGE .................................................46

SPÉCIFICATIONS ÉLECTRIQUES –

ÉTATS-UNIS SEULEMENT ............................................. 47

RACCORDEMENT DE LA SÉCHEUSE ÉLECTRIQUE –

CANADA UNIQUEMENT .................................................48

INSTALLATION ÉLECTRIQUE –

ÉTATS-UNIS SEULEMENT ............................................ 49

RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE ...............54

LISTE DE VÉRIFICATION POUR

INSTALLATION TERMINÉE ............................................54

INVERSION DE LA PORTE (FACULTATIF) .....................55

DÉPANNAGE ......................................................................... 60

ASSISTANCE OU SERVICE ...................... Couverture arrière

3

Accessories

INSTALLATION & MAINTENANCE

ACCESSORIES

FACTORY CERTIFIED PARTS – these three

words represent quality parts and accessories

designed specically for your appliance.

Time tested engineering that meets

our strict quality specications.

FACTORY CERTIFIED PARTS

Accessories designed for your appliance:

Enhance your new washer and dryer with the following

genuine Whirlpool accessories. For more information

on options and ordering, call 1-866-698-2538, or visit us

at: www.whirlpool.com/accessories. In Canada, call

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

Stack Kit

If space is at a premium, the stack kit

allows the dryer to be installed on top

of the washer.

OPERATING INSTRUCTIONS

12" Pedestal

Color-matched pedestals raise the

washer and dryer to a more comfortable

working height.

4

Use Automatic Cycles for better fabric care and energy savings

Use the Automatic Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Automatic Cycles,

condensing dryer unit temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle

and the dryer shuts off when the load reaches the selected dryness. Use the NORMAL dryness level to provide optimal energy

savings. With Timed Dry, the dryer runs the amount of time set and can result in shrinkage, wrinkling, and static due to over-

drying. Use Timed Dry for the occasional damp load that needs a little more drying time.

3

4

2

1

5

Condenser is drying air and discharging

condensation water

Drying

Air blower

Evaporator is drying air and discharging

condensation water

Heater

1

2

3

4

Condenser Dryer Technology

A typical air vented dryer uses large amounts of energy; this dryer consumes a fraction of the energy by recycling and reclaiming heat.

This dryer is a ventless condensing dryer that uses an air to air condenser to dry and recycle the same air. The laundry is dried with

lower temperatures; therefore it may feel cooler than expected during and after the drying process.

The condensing dryer’s heating phase is longer than in traditional air vented dryers. If possible, do not open the dryer door during the

process as heat can escape from the drum and can make longer drying times.

Beneﬁts of a Condensing Dryer

• ENERGY: Regenerates energy to reduce overall energy

consumption.

• PERFORMANCE: Allows flexibility to manage drying

performance and energy savings.

• FABRIC CARE: Capability to use less heat than vented dryer.

• VENTLESS DESIGN: Allows installation in more locations

throughout the home.

New Sounds from a Condensing Dryer

• The water from wet clothes is pumped out to your drain or

water tank. You may notice a gurgling sound occasionally.

Condensing Dryer Unit

5

Control Panel and Features

POWER BUTTON

Touch until the indicator above the Program button lights

up. Symbols appear on the control panel and sounds are

played.

PROGRAM (cycle)

When you turn on the dryer, the light above this button

will turn on. The program settings which you used last

will appear on the control panel. This button also lets you

set water conductivity (see “Adapting the dryer to water

conductivity” for more information).

PROGRAM/CYCLE AREA

An indicator next to each program/cycle lights up as you

use the knob to scroll through the list. Press the knob when

the indicator next to the desired program/cycle lights up.

CONTROL KNOB

Turn the knob to select a program/cycle for your laundry

load, change dryness level, set drying time or delay start

time, or select Other Options. Press the knob to conrm

your selection.

OPTIONS

Touch to activate additional dry options or additional

features on the dryer before touching the Start/Pause

button. Additional dry options or additional features

selected after touching the Start/Pause button may

not be activated.

To return to factory default cycle settings, unplug the dryer

for 30 seconds, then plug back in.

NOTE: Not all options are available with all cycles.

Settings

Use to specify additional settings of the dryer: Set the

Language for the display text, set the sound level for

the buttons, set the sound level for the end of cycle

alert, set the ability to recall the last used cycle, set the

amount of time that the display will remain on after it is

nished, and reset the factory settings.

A

Wrinkle Shield

™

This option helps to avoid creasing if you cannot

unload the laundry soon after the program/cycle ends.

The dryer starts to tumble the laundry periodically

a few minutes after the program/cycle ends. This

tumbling will last up to approximately 12 hours.

Tumbling can be stopped any time by touching the

Power button to turn off the dryer.

Cycle Signal

Use to turn on or off the signal indicating the end of a

drying cycle.

NOTE: Touch and hold the Cycle Signal button for

about one second to turn sounds on or off.

Delay Start

Touch to start your program/cycle at a later time.

SETTINGS

Timed Dry

Sets the length of a Timed Dry cycle.

Dryness Level

When using some Automatic Cycles on the

type of load you are drying.

NOTE: Dryness Level is for use with

Automatic Cycles only.

OTHER OPTIONS

Rapid

This option provides quicker drying.

Gentle

This option dries laundry more gently by reducing

the drying temperature.

START/PAUSE BUTTON

Touch to start, or touch and hold to pause, a program/

cycle.

LED DISPLAY

When you select a program or cycle, using the knob,

the name of the cycle will be displayed here, as well as

the estimated time remaining. Factors such as load size,

dryness level may affect the time that is displayed.

B

C

D

A

8

9

1

2

3

4

5

7

6

8

3 9

1 2

5

A B C

D A

B

4

7

6

Items

to Dry:

Cycle:

Dryness

Level:

Available

Options:

Cycle Details:

Work clothes,

casual wear,

corduroys

Normal Normal

Wrinkle Shield

™

Dryness Level

Uses Low/Medium Heat to thoroughly dry large loads of

mixed fabrics and items.

Whites, Sturdy

Items

Whites

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Rapid

Gentle

Cycle uses medium heat with no drum reversing to

properly dry whites items.

Undergarments,

blouses, lingerie Delicates

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses extra low heat to gently dry delicate items.

Colored clothes

Colors

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses lower heat than the whites to gently dry colored

clothes.

Normally soiled

laundry made of

articial bers or

cotton blends

Synthetics

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses low heat to gently dry delicate items. Drum

reverses intermittently to redistribute load for thorough

drying.

Jeans, Overalls,

Denim

Jeans

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Rapid

Gentle

Uses higher heat than normal cycle to dry denim items.

Do not over ll the drum or longer dryer may be noticed.

Cotton Towels,

Heavyweight Items Towels

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses Medium heat to dry large loads of cotton towels or

heavyweight items. Tumbling reverses intermittently to

redistribute the load for thorough drying.

Jackets,

Comforters, Duvets,

Pillows

Bulky

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Rapid

Gentle

Use for drying large, bulky items; do not overll dryer

drum.

Performance /

exercise wear Sports

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Use for drying exercise wear; do not overll dryer drum.

Cotton Garments Quick Dry Normal N/A

Ideal for drying garments spun at high speed in the

washing machine.

Shirts, Blouses,

Slacks Refresh Normal N/A

Use to reduce odors and light wrinkles. Do not add dryer

sheets. When loading laundry into the drum, add a wet

wash cloth.

Kids clothes,

Women's Dresses,

Pajamas, Cotton,

Wool, Silk, Dress

shirts

More

Cycles

N/A N/A

More cycles available. See section below.

Program/Cycle Guide – Automatic Cycles

Settings and options shown in bold are default settings for that cycle. If settings are changed, the new settings will be remembered.

If there is a power failure, settings will return to the default. Not all settings and options are available on each cycle.

Use Automatic Cycles for better fabric care and energy savings

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Use the NORMAL dryness level to provide optimal energy savings.

Load Size Recommendations

For best results, follow the wet load size recommendations noted for each cycle.

Small load: Fill the dryer drum with 3–4 items, not more

than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not pack tightly. Items need to tumble freely.

STATUS INDICATOR (next to LED Display)

This indicator will light up to alert you when certain conditions

occur. The condition will be displayed in the LED Display.

Symbols

Water tank full (see “Empty Water Tank” in “Using

Your Dryer”)

Clean bottom lter (see “Cleaning the Bottom Filter” in

“Dryer Care”)

Clean door lter (see “Cleaning the Lint Screen”

in “Dryer Care”)

Check bottom lter (see "Positioning the bottom lter" in

"Dryer Care")

7

Load Size Recommendations

For best results, follow the wet load size recommendations noted for each cycle.

Small load: Fill the dryer drum with 3–4 items, not more

than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not pack tightly. Items need to tumble freely.

Adjust drying time on Timed Dry Cycles

Instead of having the machine auto terminate the cycle, timed dry can be selected as an option on the 4 cycles below.

Upon selecting the button Timed Dry, the dry time can be set 15 to 120 min (2 hours).

Program/Cycle Guide – Adjustable Time Cycles

Settings and options shown in bold are default settings for that cycle. If settings are changed, the new settings will be

remembered. If there is a power failure, settings will return to the default. Not all settings and options are available on each cycle.

Items to Dry Cycle

Dryness

Level

Available

Options

Cycle Details

Whites, Sturdy

Items

Whites

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Rapid

Gentle

Cycle uses medium heat with no drum reversing to properly dry

whites items.

Undergarments,

blouses, lingerie

Delicates

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses extra low heat to gently dry delicate items.

Colored clothes Colors

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses lower heat than the whites to gently dry colored clothes.

Normally soiled

laundry made

of articial

bers or cotton

blends

Synthetics

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Uses low heat to gently dry delicate items. Drum reverses

intermittently to redistribute load for thorough drying.

More Cycles Details

To set one of the following cycles, select “More Cycles” on the display, use the knob to select the desired cycle and press the knob to

conrm the selection.

Items

to Dry:

Cycle:

Dryness

Level:

Available

Options:

Cycle Details:

Mixed Cotton

Items, sheets

Cotton

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Standard cotton cycle, suitable to dry normally wet cotton.

Wool items labeled

with the Woolmark

logo and identied

as machine

washable

Wool Normal N/A

Programme for drying wool clothing. It is advisable to

turn the garments inside out before drying. Leave to dry

naturally the heaviest edges that are still damp.

Silk Items (Shirts,

blouses, scarfs,

undergarments)

Silk Normal N/A

Uses lower heat than the delicates cycle to gently dry silk

items.

Shirts made from

cotton or cotton

blends/synthetics

Dress Shirts

More

Normal

Less

Wrinkle Shield

™

Dryness Level

Gentle

This is a cycle or Shirts made from cotton or cotton blend/

synthetics.

NOTE: These clothes dryer's Government energy certifications were based on the Normal Cycle, Non adjustable Temperature Setting

and Normal Dryness Level. The as-shipped default of Wrinkle Shield off was used.

8

Using Your Dryer

WARNING: To reduce the risk of re, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

1. Empty water tank

Hold the handle and carefully pull out the water tank.

Holding the full water tank with both hands, empty out the

water. Then push the container back into place. Make sure

that it is properly inserted.

2. Clean door lint screen

Clean the lint screen before or after each load. Pull the lint

screen straight up and out. Press tab down and open lint

screen. Roll lint off the screen with your fingers. Push the lint

screen firmly back into place.

IMPORTANT: Clean lint screen before each dryer use

as a screen blocked with lint will increase drying time.

3. Clean bottom ﬁlter

Clean the bottom filter after every 3 cycles. Open the filter

door on the bottom of the dryer and grab the handle to pull

out filter. A small amount of water may escape from the area.

Placing a absorbent towel under the flap will capture the

water. Clean the filter by hand or rinse with water – do not

wash the filter foam in a washer. Wring out the filter foam – do

not insert it in the bottom filter dripping wet. For additional

cleaning information, see “Dryer Care.”

Replace the bottom filter in the filter chamber. Fold the filter

handle down and close the bottom door.

NOTE: To turn off the “Clean bottom filter” status indicator,

the filter must be removed and replaced with the Power

button touched ON and no cycle running.

4. Rinse the Heat Exchanger

Approximately every 3 months the heat exchanger will need

to be cleaned. Cool the machine down completely. A small

amount of water may escape, therefore place an absorbent

cloth under the maintenance flap. Remove the bottom filter,

shown in step 3. Turn down both locking levers, and remove

the heat exchanger. Rinse the heat exchanger thoroughly,

removing all of the lint.

9

6. Touch Power button to turn on dryer

5. Load dryer

Open the door by pulling on the handle. Place laundry

in the dryer. Add a dryer sheet to wet load if desired.

Close the door.

IMPORTANT: Do not tightly pack the dryer. Items need

to tumble freely. Tightly packing can lead to poor drying

performance and may increase wrinkling and tangling.

7. Select program/cycle

Turn the knob to select a program/cycle for your laundry load.

As you turn the knob, an indicator light will light up next to the

program/cycle names to the left of the knob and the program/

cycle name will also appear in the LED display. Stop turning

when the indicator next to the desired program/cycle lights

up. Press the knob to conrm your selection.

See “Program/Cycle Guide” for details on program/cycle

features. Turning the knob to More Cycle, then depressing

the 6th Sense button, will present additional cycles in the LED

display than that is predominantly displayed.

8. Select options, if desired

9. Setting a delayed start, if desired

If you do not want to begin a cycle immediately, you may

choose the Delay Start option. This will delay the start

of the drying cycle by up to 24 hours.

To set a Delayed Start:

1. Touch the Delay Start button to set the desired delay time.

2. Turn the knob to the number of hours you want to delay

the start of the drying cycle. The delay time will appear

on the display. Press the knob to conrm your selection.

After touching the Start/Pause button, the time will count

down until the delay time has been reached. The dryer will

start and the display will show the remaining time in the cycle.

10. If Air Dry or Timed Dry was selected,

set drying time

When you select a timed cycle, the indicator light above

“Timed Dry” lights up. Turn the knob to select the desired

time, up to 120 minutes. Press the knob to conrm your

selection.

10

15. Remove garments promptly

after cycle is ﬁnished

Promptly remove garments after cycle has completed

to reduce wrinkling.

12. Select any additional options

*

After setting drying time or dryness level, the indicator light

above “Options” lights up. Turn the knob to select the desired

option(s). As you turn the knob, the option symbols above the

Options button will light up one at a time as you turn the knob.

Stop turning when the symbol of the desired option lights up.

Press the knob to conrm your selection.

*

Not all options and settings are available with all

program/cycles. See “Program/Cycle Guide” for available op-

tions and settings.

When the display indicates that the cycle has nished, touch

the Power button to turn off the dryer. Open the door and take

out your laundry.

To save energy, the dryer turns off automatically about

a quarter hour after the program/cycle ends.

If not turned off right after the program/cycle ends, the

dryer will tumble the laundry for about 10 minutes to prevent

wrinkling. The display shows an animation.

NOTE: If the Power button is touched and held, a countdown

will be displayed. At the end of the countdown, any errors will

be erased and the program/cycle will restart.

13. Touch Start/Pause button to begin

drying program/cycle

Touch the Start/Pause button to start the drying

program/cycle. To pause a program/cycle in progress, touch the

Start/Pause button once, then touch again to continue the

program/cycle. To cancel a program/cycle, touch the Power

button.

14. Touch Power button to turn off

dryer after program/cycle ends

11. If an automatic cycle was selected,

set dryness level

When you select an automatic cycle, the indicator light above

“Dryness Level” lights up. Turn the knob to select the desired

level. As you turn the knob, an indicator light will light up next

to the dryness levels to the right of the knob. Stop turning

when the indicator next to the desired level lights up. Press

the knob to conrm your selection.

11

Dryer Care

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would

block the airflow for proper dryer operation. This includes

clearing piles of laundry in front of the dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum:

1. Use a mild hand dish detergent mixed at a low

concentration with very warm water, and rub with

a soft cloth.

2. Rinse well with a wet sponge or towel.

3. Tumble a load of clean clothes or towels to dry drum

OR

Use a microfiber cloth and hot water in a spray bottle

to clean the drum and a second microfiber towel to dry.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done

by a qualified appliance servicer.

CLEANING THE LINT SCREEN

Clean lint screen after every load.

The lint screen is located in the door opening of the dryer.

A screen blocked by lint can increase drying time.

To clean:

1. Pull the lint screen straight up and out. Press tab down

and open lint screen. Roll lint off the screen with your

fingers.

2. Push the lint screen firmly back into place.

IMPORTANT:

Ƀ Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

As-needed cleaning

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash lint screen:

1. Roll lint off the screen with

your fingers.

2. Wet both sides of lint screen

with hot water.

3. Wet a nylon brush with hot water

and liquid detergent. Scrub lint

screen with the brush to remove

residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with

a clean towel. Reinstall screen

in dryer.

12

CLEANING OF THE CONDENSER

CLEANING THE BOTTOM FILTER

1. Approximately every 3 months, clean the condensing unit

situated behind the bottom filter.

2. Lower the levers situated on the sides of the condenser.

After having removed the condenser, clean it under

running water.

3. Place the condenser back in place and lift the levers.

4. Close the rear side of the bottom filter and place it back

by checking it is perfectly integrated in place.

5. Lower the filter handle and close the bottom door.

6. Make sure the air intake is free.

Clean bottom filter after every 3 loads.

The filter is located in bottom corner of dryer.

To clean:

1. Pull the lint screen straight up and out. Press tab down

and open lint screen. Roll lint off the screen with your

fingers.

2. Push the lint screen firmly back into place.

As-needed cleaning:

Laundry detergent and fabric softener residue can build up

on the lint screen. This buildup can cause longer drying times

for your clothes, or cause the dryer to stop before your load

is completely dry.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash lint screen:

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Reinstall

screen in dryer.

IMPORTANT:

Ƀ Do not run the dryer with the filter loose, damaged,

blocked, or missing. Doing so can cause overheating

and damage to both the dryer and fabrics.

NON-USE, STORAGE, AND MOVING CARE

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Empty water tank.

2. Unplug dryer or disconnect power.

3. Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected dryers:

1. Empty water tank.

2. Unplug the power supply cord.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

NON-USE, STORAGE, AND

MOVING CARE (cont.)

For direct-wired dryers:

1. Empty water tank.

2. Disconnect power.

3. Disconnect wiring.

4. Make sure leveling legs are secure in dryer base.

5. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the “Installation Instructions” section to locate, level,

and connect the dryer.

13

INSTALLATION INSTRUCTIONS

Installation Requirements

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed:

Flat-blade screwdriver #2 Phillips screwdriver

Min. 8" long TORX

®

T20

®†

screwdriver

Wire stripper (direct wire

installations)

Channel locks

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

1/4" and 5/16" nut driver

(recommended)

Pliers

If using a power supply cord:

Use a UL-listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

Ƀ A UL-listed 30 A power supply cord, rated 120 V/240 V

minimum. The cord should be type SRD or SRDT and

be at least 4 ft. (1.22 m) long. The wires that connect to

the dryer must end in ring terminals or spade terminals

with upturned ends.

Additional Accessories: (Not supplied with dryer)

Refer to “Operating Instructions” for information about

accessories available for your dryer.

†

®

TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Utility knife

Tape measure

Level

14

Location Requirements

Check code requirements. Some codes limit, or do not permit,

installing dryer in garages, closets, mobile homes, or sleeping

quarters. Contact your local building inspector.

You will need:

Ƀ A separate 30 A circuit.

Ƀ If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer.

See “Electrical Requirements.”

Ƀ Floor must support dryer weight of 200 lbs. (90.7 kg).

Also consider weight of companion appliance.

Ƀ Level floor with maximum slope of 1" (25 mm) under entire

dryer. If forward slope is greater than 1" (25 mm), water

could run out from front of filter. If not level, clothes may

not tumble properly and automatic sensor cycles may

not operate correctly.

Ƀ For garage installation, place dryer at least 18" (460 mm)

above floor. If using a pedestal, you will need 18" (460 mm)

to bottom of dryer.

IMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below

40°F (4°C). Lower temperatures may cause dryer not to shut

off at end of automatic sensor cycles, resulting in longer

drying times.

DRYER DIMENSIONS

(595 mm)

23 / "

1

2

(860 mm)

33 / "

7

8

(865 mm)

34" Max.

Front view:

Side view:

(1100 mm)

(655 mm)

(15 mm)

26"

43 / "

5

16

19/32"

Back view:

(687 mm)

(15 mm)

(100 mm)

19/32"

27"

NOTES:

Ƀ Allow clearance behind dryer for proper drain hose routing.

Push dryer back as far as possible and make sure drain

hose is not crushed or kinked.

Ƀ Water can be drained into an alternate location. Remove

the top end of the white hose from the water tank and

install, for example, in a floor standpipe (see “Drain

System”).

Power cord/

cable

15

Installation spacing for recessed area or closet

installation

All dimensions show recommended and minimum spacing

allowed.

Ƀ Additional spacing should be considered for ease of

installation and servicing.

Ƀ Additional clearances might be required for wall, door,

floor, moldings, and drain system.

Ƀ Additional spacing should be considered on all sides

of the dryer to reduce noise transfer.

Ƀ For closet installation with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

Ƀ Companion appliance spacing should also be considered.

Recommended installation clearances (dryer only):

0"

(0 mm)

0"

(0 mm)

0" - 5"*

(0 mm - 127 mm)

24 in.

2

Min.

(155 cm

2

)

48 in.

2

Min.

(310 cm

2

)

3"

(76 mm)

3"

(76 mm)

0"

(0 mm)

*NOTE: 0"–5"

(0 mm–127 mm)

spacing is allowed

behind dryer, providing

drain hose is not kinked

or pinched.

Mobile home – Additional installation requirements:

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile home con-

struction and Safety, Title 24, HUD Part 280) or

Standard CAN/CSA-Z240 MH.

Minimum diameter for a standpipe drain: 2" (51 mm). Top of

standpipe must be at least 30" (762 mm) high; install no higher

than 36" (910 mm) from bottom of dryer.

Floor standpipe drain system

Drain system can be installed by routing the white hose to

a oor drain, wall standpipe, oor standpipe, or laundry tub

instead of to the water tank. Select the method you need.

IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain

hose should be inside standpipe; do not force excess hose

into standpipe. Always secure drain hose with a cable tie

(not supplied).

4.5"

(114 mm)

4.5"

(114 mm)

Max. 36"

(910 mm)

Min. 30"

(762 mm)

Custom under-counter installation:

0" Min.

(0 mm)

0"Min.

(0 mm)

0"Min.

(0 mm)

34½

" Min.

(876 mm)

DRAIN SYSTEM

16

Electrical Requirements –

U.S.A. Only

It is your responsibility:

Ƀ To contact a qualified electrical installer.

Ƀ To be sure that the electrical connection is adequate and

in conformance with the National Electrical Code, ANSI/

NFPA 70 – latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

Ƀ To supply the required 3- or 4-wire, single-phase,

120/240 V, 60 Hz, AC-only electrical supply (or 3- or 4-wire,

120/208 V electrical supply, if specified on the serial/rating

plate) on a separate 30 A circuit, fused on both sides of the

line. Connect to an individual branch circuit. Do not have a

fuse in the neutral or grounding circuit.

Ƀ Do not use an extension cord.

Ƀ If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type

of electrical connection you will be using and follow the

instructions provided for it here.

Ƀ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. A neutral ground conductor

(blue wire) is provided between the power supply neutral

connection (center terminal) and the dryer external

grounding point (green screw). If the dryer is installed with a

4-wire electrical supply connection, one end of the neutral

ground conductor must be removed from the external

ground connector (green screw), and secured under the

neutral terminal (center screw) of the terminal block. When

both ends of the neutral ground conductor are secured

under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor. The green ground wire of the 4-wire power cord

must be secured to the dryer cabinet with the green ground

screw.

Ƀ If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional External

Ground 3-wire connection”.

Ƀ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

after 1996, (2) mobile homes, (3) recreational vehicles, and

(4) areas where local codes prohibit grounding through the

neutral conductors.

If using a power supply cord:

Use a UL-listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

Ƀ A UL-listed 30 A power supply cord, rated 120/240 V

minimum. The cord should be type SRD or SRDT and be

at least 4 ft. (1.22 m) long. The wires that connect to

the dryer must end in ring terminals or spade terminals

with upturned ends.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

Ƀ Flexible armored cable or nonmetallic sheathed copper

cable (with ground wire), covered with flexible metallic

conduit. All current-carrying wires must be insulated.

Ƀ 10-gauge solid copper wire (do not use aluminum) at least

5 ft. (1.52 m) long.

Then choose a 4-wire power supply cord with

ring or spade terminals and UL-listed strain

relief. The 4-wire power supply cord, at least

4 ft. (1.22 m) long, must have four 10-gauge

copper wires and match a 4-wire receptacle

of NEMA-Type 14-30R. The ground wire

(ground conductor) may be either green

or bare. The neutral conductor must be

identified by a white cover.

Then choose a 3-wire power supply cord with

ring or spade terminals and UL-listed strain

relief. The 3-wire power supply cord, at least

4 ft. (1.22 m) long, must have three 10-gauge

copper wires and match a 3-wire receptacle

of NEMA-Type 10-30R.

4-wire

receptacle

(14-30R)

3-wire

receptacle

(10-30R)

If your outlet looks like this:

17

Electric Dryer Power Hookup Electric Dryer Power Hookup

– Canada Only– Canada Only

Electrical Requirements

It is your responsibility:

Ƀ To contact a qualified electrical installer.

Ƀ To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code,

C22.1 – latest edition and all local codes. A copy of the

above codes standard may be obtained from: Canadian

Standards Association, 178 Rexdale Blvd., Toronto, ON

M9W 1R3 CANADA.

Ƀ To supply the required 4-wire, single-phase, 120/240 V,

60 Hz., AC-only electrical supply on a separate 30 A circuit,

fused on both sides of the line. A time-delay fuse

or circuit breaker is recommended. Connect to an individual

branch circuit.

Ƀ This dryer is equipped with a CSA

International Certified Power Cord intended

to be plugged into a standard 14-30R wall

receptacle. The cord is 5 ft. (1.52 m) in

length. Be sure wall receptacle is within

reach of dryer’s final location.

Ƀ Do not use an extension cord.

If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

8579325. For further information, please reference the

“Assistance or Service” section.

Electric Installation –

U.S.A. Only

1. Choose electrical connection type

Power supply cord 4-wire receptacle

(NEMA-Type 14-30R):

Go to “Power Supply Cord Connection.”

3-wire direct connection:

Go to “Direct Wire Connection.”

4-wire direct connection:

Go to “Direct Wire Connection.”

Power supply cord 3-wire receptacle

(NEMA Type 10-30R):

Go to “Power Supply Cord Connection.”

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to “Optional

External Ground for 3-Wire Connection.” This connection

can be used with either a power supply cord or a direct

wire connection.

Before you start: disconnect power.

4-wire receptacle

(14-30R)

Remove hold-down screws and terminal block cover.

2. Remove terminal block cover

18

WARNING

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals.

Securely tighten all electrical connections.

Failure to do so can result in death, ﬁre, or

electrical shock.

4-Wire Power Supply Cord Strain Relief:

IMPORTANT: Use the strain relief supplied with the dryer.

Power Supply Cord Connection

4-Wire Power Supply Cord Connection

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use

of 3-wire connections.

4-wire receptacle

(NEMA-type 14-30R)

4 prong plug

Spade terminals with

upturned ends

Ring terminals

Attach power supply cord to strain relief

Connect neutral wire (white or center) (C) of power supply cord

under center terminal block screw (B). Tighten screw.

1. Connect neutral wire

B

C

D

Power supply cord 4-wire receptacle

(NEMA-Type 14-30R):

Go to “4-Wire Power Supply Cord

Connection.”

Power supply cord 3-wire receptacle

(NEMA-Type 10-30R):

Go to “3-Wire Power Supply Cord

Connection.”

If your outlet looks like this:

Put power supply cord through the strain relief. Be sure that

the wire insulation on the power supply cord is inside the

strain relief. Do not further tighten strain relief screws at

this point.

Connect ground wire (F) (green or bare) of power supply

cord under green external ground conductor screw (A).

Tighten screw.

2. Connect ground wire

F

A

19

3. Connect remaining wires

Connect remaining wires under outer terminal block screws.

Tighten screws, tighten strain relief screws. Finally, replace the

terminal block cover and secure with the 4 hold-down screws.

Now, go to “Level Dryer.”

2. Connect remaining wires

Connect remaining wires under outer terminal block screws.

Tighten screws, tighten strain relief screws. Finally, replace the

terminal block cover and secure with the 4 hold-down screws.

Now, go to “Level Dryer.”

Connect neutral (center) wire (C) of power supply cord

under

center terminal block screw (B)

. Tighten screw.

3-Wire Power Supply Cord Strain Relief:

IMPORTANT: Use the strain relief supplied with the dryer.

Attach power supply cord to strain relief

Put power supply cord through the strain relief. Be sure that

the wire insulation on the power supply cord is inside the

strain relief. Do not further tighten strain relief screws at

this point.

1. Connect neutral (center) wire

D

C

B

3-wire receptacle

(NEMA-type 10-30R)

3 prong plug

Spade terminals with

upturned ends

Ring terminals

3-Wire Power Supply Cord Connection

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

20

Direct Wire Connection

WARNING

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals.

Securely tighten all electrical connections.

Failure to do so can result in death, ﬁre, or

electrical shock.

Direct Wire Strain Relief

IMPORTANT: Use a conduit strain relief (not supplied).

3. Attach direct wire cable to strain relief

Put direct wire cable through the strain relief. The strain

relief should have a tight fit with the dryer cabinet and be

in a vertical position. Tighten strain relief screw against the

direct wire cable.

3-wire direct connection:

Go to “3-Wire Direct Wire Connection.”

4-wire direct connection:

Go to “4-Wire Direct Wire Connection.”

If your wiring looks like this:

2. Attach direct wire strain relief

Put the strain relief (B) through the hole below the terminal

block opening (A). Press the strain relief from bottom to fit into

the hole. Make sure that strain relief is fitted properly in the

hole.

1. Remove existing strain relief

With a flat-blade screwdriver, flatten the three tabs on the

band at the top of the strain relief. Pull out strain relief.

A

B

La page charge ...

Whirlpool WCD3090JW Manuel utilisateur

Ce manuel convient également à

Whirlpool WCD3090JW Manuel utilisateur

dans d''autres langues

Documents connexes