Gaggenau VL 414 712 Manuel utilisateur

*DJJHQDX

Installation instructions2

Notice de montage16

Instrucciones de instalación31

VL 414 712

Downdraft ventilation

Aérateur de plan de cuisson

Extractor de superficie

2

en-us

Table of Contents

Installation instructions

9 Safety Definitions 2

IMPORTANT SAFETY INSTRUCTIONS 3

Appliance Handling Safety 5

Safety Codes and Standards 6

Electric Safety 6

Related Equipment Safety 7

Proposition 65 Warning 7

Before you begin 8

Tools and Parts Needed 8

Parts Included 8

Installation accessories 8

Ventilation molding 8

Prepare Installation Space 9

Countertop Requirements 9

Installation Procedure 10

Mounting Control Knobs 10

Install Appliance 11

Connecting device 14

Connection for window contact switch AA 400 510 15

Removing appliance 15

Customer service 15

Additional information on products, accessories,

replacement parts and services, as well as the Use and

care manual and the Installation instructions can be

found at www.gaggenau.com and in the online shop

www.gaggenau.com/zz/store

9 Safety Definitions

Safety Definitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this

warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this

warning.

NOTICE

This indicates that damage to the appliance or property

may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or

tips.

3

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: LEAVE THESE

INSTRUCTIONS WITH THE APPLIANCE

AFTER INSTALLATION IS COMPLETE.

IMPORTANT: SAVE THESE

INSTRUCTIONS FOR THE LOCAL

ELECTRICAL INSPECTOR'S USE.

9 WARNING

If the information in this manual is

not followed exactly, fire or shock

may result causing property damage

or personal injury.

9 WARNING

Do not repair, replace or remove any

part of the appliance unless

specifically recommended in the

manuals. Improper installation,

service or maintenance can cause

injury or property damage. Refer to

this manual for guidance. All other

servicing should be done by an

authorized service provider.

9 WARNING

WARNING – TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

▯ Installation work and electrical

wiring must be done by qualified

person(s) in accordance with all

applicable codes and standards,

including fire-rated construction.

▯ Sufficient air is needed for proper

combustion and exhausting of

gases through the flue (chimney)

of fuel burning equipment to

prevent back drafting. Follow the

heating equipment manufacturer’s

guideline and safety standards

such as those published by the

National Fire Protection

Association (NFPA), and the

American Society for Heating,

Refrigeration and Air Conditioning

Engineers (ASHRAE), and the

local code authorities.

▯ When cutting or drilling into wall

or ceiling, do not damage

electrical wiring and other hidden

utilities.

▯ Ducted fans must always be

vented to the outdoors.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

4

9 WARNING

The applicable regulations of the

energy supply companies and the

regional construction regulations

must be observed when installing

the hood.

9 WARNING

Risk of fire!

If the downdraft ventilator is installed

next to a gas appliance, an air baffle

must be used (available as

accessory). This prevents the flame

from being drawn into the fan. Thus,

a filter soaked in grease cannot be

ignited by the gas flame.

9 WARNING

Risk of injury!

From sharp edges during

installation. Always wear protective

gloves while installing the appliance.

9 WARNING

Risk of fire!

Grease deposits in the grease filter

can catch fire. Never work with a

naked flame near the appliance (e.g.

flambéing). Install the unit near a

heat-producing appliance for solid

fuels (e.g. wood or coal) only if there

is a closed, non-detachable cover.

There must be no flying sparks.

9 WARNING

Fire risk!

Grease deposits in the grease filter

can ignite. If the appliance is used

next to a gas appliance, a ventilation

molding must be fitted during

cooking. The ventilation molding

improves extraction when using gas

appliances. The ventilation molding

prevents extinction of small flames

due to the draft.

9 WARNING

To reduce risk of fire and to properly

exhaust air, be sure to duct air

outside. Do not vent exhaust air into

spaces within walls, ceilings, attics,

crawl spaces or garages.

9 WARNING

To reduce the risk of fire, use only

metal ductwork.

5

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

9 WARNING

When the hood is operated in

exhaust-air mode simultaneously with

a different burner which also makes

use of the same chimney (such as

gas, oil or coal-fired heaters,

continuous-flow heaters, hot-water

boilers) care must be taken to

ensure that there is an adequate

supply of fresh air which will be

needed by the burner for

combustion.

Safe operation is possible provided

that the under pressure in the room

where the burner is installed does

not exceed 4 Pa (0.04 mbar).

This can be achieved if combustion

air can flow through non-lockable

openings, e.g. in doors, windows

and via the air-intake/exhaust-air wall

box or by other technical measures,

such as reciprocal interlocking, etc.

9 WARNING

Avoid carbon monoxide poisoning –

Provide adequate air intake so

combustion gases are not drawn

back into the room.

An air-intake/exhaust-air wall box by

itself is no guarantee that the limiting

value will not be exceeded.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does

not apply to the use of cooking

appliances, such as cooktops and ovens.

9 CAUTION

For general ventilating use only. Do

not use to exhaust hazardous or

explosive materials and vapors.

Appliance Handling Safety

Unit is heavy and requires at least two

people or proper equipment to move.

9 WARNING

Risk of injury!

The appliance may fall from the wall

if it is not attached properly. All

fastening components must be fixed

firmly and securely in place.

9 WARNING

Risk of tipping over!

The appliance is very narrow and can

tip over easily. Do not place

appliance upright on the floor. Place

the appliance flat on the floor.

Hidden surfaces may have sharp

edges. Use caution when

reaching behind or under

appliance.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

6

Safety Codes and Standards

This appliance complies with the latest

version of one or more of the following

standards:

▯ UL 507 - Electric Fans

▯ CAN/CSA C22.2 No. 113 - Fans and

Ventilators

It is the responsibility of the installer to

determine if additional requirements and/

or standards apply to specific

installations.

Electric Safety

9 WARNING

GROUNDING INSTRUCTIONS!

This appliance must be grounded. In

the event of an electrical short

circuit, grounding reduces the risk of

electric shock by providing an

escape wire for the electric current.

This appliance is equipped with a

cord having a grounding wire with a

grounding plug. The plug must be

plugged into an outlet that is

properly installed and grounded.

9 WARNING

Improper grounding can result in a

risk of electric shock. Consult a

qualified electrician if the grounding

instructions are not completely

understood, or if doubt exists as to

whether the appliance is properly

grounded. Do not use an extension

cord. If the power supply cord is too

short, have a qualified electrician

install an outlet near the appliance.

9 WARNING

Before you plug in an electrical cord

or turn on power supply, make sure

all controls are in the OFF position.

For appliances equipped with a cord and

plug, do not cut or remove the ground

prong. It must be plugged into a matching

grounding type receptacle to avoid

electrical shock. If there is any doubt as

to whether the wall receptacle is properly

grounded, the customer should have it

checked by a qualified electrician.

If required by the National Electrical

Code (or Canadian Electrical Code), this

appliance must be installed on a separate

branch circuit.

9 WARNING

To reduce the risk of fire or electric

shock, do not use this fan with any

solid-state speed control device.

7

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Installer – show the owner the location of

the circuit breaker or fuse. Mark it for

easy reference.

Before installing, turn power OFF at the

service panel. Lock service panel to

prevent power from being turned ON

accidentally.

9 WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE

FOLLOWING:

▯ Use this unit only in the manner

intended by the manufacturer. If

you have questions, contact the

manufacturer.

▯ Before servicing or cleaning unit,

switch power off at service panel

and lock the service

disconnecting means to prevent

power from being switched on

accidentally.

When the service disconnecting

means cannot be locked, securely

fasten a prominent warning

device, such as a tag, to the

service panel.

Be sure your appliance is properly

installed and grounded by a qualified

technician. Installation, electrical

connections and grounding must comply

with all applicable codes.

9 WARNING

Risk of electric shock!

Parts inside the appliance can have

sharp edges. The connection cable

can be damaged. Do not bend or

pinch connection cables during

installation.

Related Equipment Safety

Remove all tape and packaging before

using the appliance. Destroy the

packaging after unpacking the appliance.

Never allow children to play with

packaging material.

The appliance should only be used if

installed by a qualified technician in

accordance with these installation

instructions. The manufacturer is not

responsible for any damage resulting

from incorrect installation.

Never modify or alter the construction of

the appliance. For example, do not

remove leveling legs, panels, wire covers

or anti-tip brackets/screws.

Proposition 65 Warning:

This product may contain a chemical

known to the State of California, which

can cause cancer or reproductive harm.

Therefore, the packaging of your product

may bear the following label as required

by California:



&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY

67$7(2)&$/,)251,$352326,7,21:$51,1*

:$51,1*

8

en-us Before you begin

Before you begin

Tools and Parts Needed

▯ Phillips Head Screwdriver

▯ Pencil

▯ Drill with ¼" (6 mm) bit

▯ Jigsaw

▯ Tape Measure

Note: Additional materials may be necessary for

installation in solid surface countertops. Contact the

countertop manufacturer.

Parts Included

Installation accessories

Ventilation molding

If downdraft ventilation is used next to a gas appliance, a

ventilation molding AA 414 010 must be fitted on the gas

appliance during cooking. The ventilation molding

improves extraction when using gas appliances. The

ventilation molding prevents extinction of small flames

due to the draft.

VA 420 000 Connection strip for combination with

other Vario appliances in the 400 series

for flush installation

VA 420 010 Connection strip for combination with

other Vario appliances in the 400 series

for surface-mounted installation

AD 851 041 Connecting pieces for extending

AD 410 040 Flex connection hose

9

Prepare Installation Space en-us

Prepare Installation Space

The kitchen unit must be heat-resistant to at least

200° F (90°C). The stability of the unit must be

maintained after producing the cut-out.

Produce the cut-out in the countertop for one or more

Vario appliances as shown in the installation sketch. The

angle between the cut surface and the countertop must

be 90°.

The cut edges at the sides must be flat to ensure a good

fit of the retaining springs on the appliance. In laminated

worktops, it may be necessary to fit strips at the sides of

the cut-out.

Remove shavings after cutting. Seal cut surfaces for

resistance to heat and so they are watertight.

Pay attention to a minimum gap of 3/8“ (10 mm) from the

underside of the appliance to kitchen units.

Countertop Requirements

The countertop must be level and horizontal. The stability

of the countertop must be maintained after the cut-out

has been made.

10

en-us Installation Procedure

Flush installation: The appliance can be installed in the

following temperature- and water-resistant countertops:

▯ Stone countertops

▯ Plastic countertops (such as Corian®)

▯ Solid wood countertops: Only in consultation with the

manufacturer of the countertop (seal cut-out edges)

▯ Installation in other countertops only in consultation

with the manufacturer of the countertop.

Installation in countertops made of particleboard is not

possible.

Note: Any cut-out work on the countertop must be

performed in a workshop according to the installation

diagram. The cut-out must be made cleanly and precisely

since the cut-out edge is visible on the surface. Clean

and degrease the cut-out edges with a suitable cleaning

agent (bear in mind silicone manufacturer's processing

instructions).

Combining several Vario devices: The connecting strip

VA 420 000/010 is required for the combination of

several Vario appliances. This is available separately as a

special accessory. Consider additional space

requirement for the connecting strip between the

appliances when making the cut-out (see installation

instructions VA 420 000/010).

Appliances can also be installed in individual cut-outs,

bearing in mind a minimum distance between the devices

of 2" (51 mm).

Installation Procedure

Mounting Control Knobs

Note: Follow the installation instructions provided for the

control knobs.

1. Depending on the distance between the control

knobs, it may be necessary to break off the retaining

plate at the perforation. Hold the retaining plate in

place against the back of the control panel or the

bottom of the countertop, or secure it with the

enclosed screws.

2. When installing a single control knob or when the

retaining plate has been broken at the perforation, use

2 screws to hold each individual retaining plate in

place to prevent it from rotating (C).

For stone countertops, use temperature-resistant two-

component adhesive (for metal to stone) to adhere the

retaining plate.

3. Remove the protective film on the back of the

illuminated ring (A).

4. Insert the control knob into the drilled hole (B) and

screw the nut on the back with the enclosed

installation aid (D).

5. Connect all of the control knobs with the enclosed

shorter cables. The plugs must snap into the sockets

(E).

Note: The two cable connectors on the control knob

are identical.

6. Connect the longer cable to the control cable for

connection to the appliance. The plug must snap into

the socket (F).

Note: The appliance can be connected to any control

knob.

9$



















11

Installation Procedure en-us

7. After installing, check that all plug connections fit

correctly.

8. After installing all the cables, secure them to the

retaining plate by bending the tab down (E).

Install Appliance

9 WARNING

Before you plug in an electrical cord or turn on

power supply, make sure all controls are in the OFF

position.

Note: Observe the installation sequence. First fit the

downdraft ventilation in the cut-out on the worktop. Then

install the other appliances.

1. Use four nuts to screw the exhaust-air elbow tightly to

the appliance.

2. Insert the downdraft ventilation into the cut-out on the

worktop.

$ %

&

'

( )

12

en-us Installation Procedure

3. Insert the VA 420 000/010 connection strip (mounting

accessories) into the cut-out on the worktop.

4. Press the connection strip firmly against the

appliance; you should hear the appliance's clamp

springs clicking into the recesses in the connection

strip.

5. Install the other appliances and connection strips.

6. Insert the metal grease filter.

FOLFN

13

Installation Procedure en-us

7. Put the filter cover on.

8. Only for flush-mounted installation: Before joining, make

sure to perform a function test! Grout the surrounding

gap with a suitable temperature-resistant silicone

adhesive (e.g., OTTOSEAL

®

S 70). Smooth the joint

seal with a smoothing agent recommended by the

manufacturer. Follow the instructions for the silicone

adhesive. Only start up the appliance after the

silicone adhesive is completely dry (at least 24 hours,

depending on the room temperature).

9 CAUTION

Unsuitable silicone adhesive causes permanent

discoloration to natural stone worktops.

14

en-us Installation Procedure

Connecting device

Note: Before connecting, turn the control knob to the

zero setting.

Use the control cable to connect the downdraft

ventilation and the external remote blower. The plug must

snap into place.

Connect the power cable to a grounded power outlet that

is located below the countertop.

Route the power cable beneath the appliance.

Route the power cable away from heat generated by the

cooktop.

$5

5-

+RPH&RQ

QH

F

W

5-

$5

15

Installation Procedure en-us

Connection for window contact switch

AA 400 510

Work on the connection for the window contact switch

must only be carried out by a qualified electrician in

accordance with the requirements and standards of the

country in which in the appliance is being used.

The appliance has a connection (X17) for a window

contact switch. The window contact switch can be flush

mounted or surface mounted. You will receive the window

contact switch AA 400 510 separately as an accessory.

Please observe the installation instructions enclosed

with the window contact switch.

If a window contact switch is connected, the extractor

hood's ventilation system will only work with the window

open. The lighting will work even if the window is closed.

If you switch on the ventilation system with the window

closed, the button for the ventilation setting you have

selected will flash, and the ventilation system will not

switch on.

If you close the window while the ventilation system is on,

the appliance will switch the ventilation system off within

5 seconds. The button for the ventilation setting you have

selected will flash.

The entire ventilation network and window contact switch

must be assessed by a master chimney sweep.

Removing appliance

Disconnect the appliance from the power supply. Push

out the appliance from below.

9 CAUTION

Damage to appliance! Don't lift device out from

above.

Customer service

If your appliance needs repairs, our customer service is

there for you. We work hard to help solve problems

quickly and without unnecessary service calls, getting

your appliance back up and running correctly in the least

amount of time possible.

When you call, please indicate the product number

(E-Nr.) and serial number (FD-Nr.) so that we can support

you in a qualified manner. You will find the type plate with

these numbers on the bottom of the appliance.

To avoid having to search for a long time when you need

it, you can enter your appliance data and the customer

support telephone number here.

Please read the use and care instructions provided with

your appliance. Failure to do so may result in an error in

using the appliance. This could result in a service call

that instead of fixing a mechanical issue is only needed

for customer education. Such calls are not covered by the

appliance warranty.

Please find the contact data of all countries in the

enclosed customer service list.

To book a service visit and product advice

E-Nr. FD-Nr.

Customer Service O

USA 877 442 4436

toll-free

CANADA 877 442 4436

toll-free

16

fr-ca

Table des matières

Notice de montage

9 Définitions de sécurité 16

CONSIGNES DE SÉCURITÉ IMPORTANTES 17

Sécurité de manutention des appareils 19

Codes et normes de sécurité 20

Sécurité électrique 20

Équipement de sécurité 22

Avertissement issu de la proposition 65 22

Avant de commencer 23

Outils et pièces nécessaires 23

Pièces comprises 23

Accessoires d'installation 23

Déflecteur 23

Préparation des meubles 24

Exigences pour le plan de travail 24

Procédure d'installation 25

Monter les boutons de commande 25

Pose de l'appareil 26

Branchement de l'appareil 29

Raccord pour le contacteur de fenêtre AA 400 510 30

Dépose de l'appareil 30

Service après-vente 30

Vous trouverez des informations supplémentaires

concernant les produits, accessoires, pièces de

rechange et services, et les notices d’utilisation et de

montage sur Internet sous : www.gaggenau.com et la

boutique en ligne : www.gaggenau.com/zz/store

9 Définitions de sécurité

Définitions de sécuri té

9 AVERTISSEMENT

Ceci indique que le non-respect de cet

avertissement peut entraîner des blessures graves,

voire la mort.

9 ATTENTION

Ceci indique que le non-respect de cet

avertissement peut entraîner des blessures légères

ou de gravité moyenne.

AVIS

Ceci indique que la non-conformité à cet avis de sécurité

peut entraîner des dégâts matériels ou endommager

l'appareil.

Remarque : Ceci vous signale des informations et/ou

indications importantes.

17

9 CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

INSTALLATEUR : LAISSEZ CES

INSTRUCTIONS AVEC L'APPAREIL

APRÈS UNE FOIS L'INSTALLATION

TERMINÉE.

IMPORTANT : CONSERVER CES

INSTRUCTIONS POUR L'USAGE DE

L'INSPECTEUR ÉLECTRIQUE LOCAL.

9 AVERTISSEMENT

Si l’information de ce guide n’est

pas suivie exactement, il peut en

résulter un incendie ou un choc

électrique causant des dommages à

la propriété, des blessures ou la

mort.

9 AVERTISSEMENT

Ne réparez, remplacez, ni ne retirez

aucune partie de l'appareil, excepté

si les manuels recommandent de le

faire. Une installation, un entretien

ou une inspection incorrects peuvent

occasionner des blessures ou des

dommages matériels. Reportez-vous

au présent manuel pour obtenir des

indications. Toute autre intervention

doit être effectuée par un technicien

agréé.

9 AVERTISSEMENT

ATTENTION – AFIN DE RÉDUIRE

LES RISQUES D’INCENDIE, DE

CHOC ÉLECTRIQUE OU DE

BLESSURES CORPORELLES,

VEUILLEZ SUIVRE LES

INSTRUCTIONS SUIVANTES :

▯ Les travaux d’installation et de

raccordement électrique doivent

être effectués par une personne

qualifiée, conformément aux

codes et standards de

construction, y compris ceux

concernant le feu.

▯ Assurez-vous que l'aération est

suffisante pour permettre la

combustion et l'évacuation des

gaz par le conduit de cheminée

d'un appareil à combustible afin

de prévenir le refoulement d'air.

Respectez les instructions du

fabricant de l'appareil de

chauffage et les normes de

sécurité, comme celles publiées

par la National Fire Protection

Association (NFPA) et par la

American Society for Heating,

Refrigeration and Air Conditioning

Engineers (ASHRAE), ainsi que

par les autorités locales.

▯ Lorsque vous faites une ouverture

dans un mur ou un plafond, veillez

à ne pas endommager les fils

électriques ou les conduites qui y

sont dissimulés.

▯ Les soufflantes canalisées doivent

donner sur l'extérieur.

9 CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

18

9 AVERTISSEMENT

Pour l'installation de la hotte, vous

devez respecter tous les règlements

des entreprises de distribution

d'électricité et de construction

régionaux applicables.

9 AVERTISSEMENT

Risque d’incendie !

Si la hotte à aspiration descendante

est installée près d’un appareil à

gaz, il faut utiliser un déflecteur d’air

(offert comme accessoire). Le

déflecteur empêche l’aspiration de

la flamme par le ventilateur. On évite

ainsi d’enflammer un filtre imprégné

de graisse.

9 AVERTISSEMENT

Risque de blessure !

pendant l'installation par des arêtes

coupantes. Pendant l'installation de

l'appareil, toujours porter des gants

de protection.

9 AVERTISSEMENT

Risque d'incendie !

Les dépôts se trouvant dans le filtre

à graisse peuvent s'enflammer. Ne

jamais cuisiner à proximité de

l'appareil avec une flamme ouverte

(par exemple pour faire flamber).

Installer l'appareil près d'un foyer

pour combustibles solides (bois ou

charbon par exemple) seulement s'il

y a un couvercle fermé et non

amovible. Il ne faut pas qu'il se

produise de projection d'étincelles.

9 AVERTISSEMENT

Risque d'incendie !

Les dépôts se trouvant dans le filtre

à graisse peuvent s'enflammer. Si

l'appareil est installé près d'un

appareil à gaz, il faut installer un

déflecteur pendant la cuisson. Le

déflecteur améliore la capacité

d'aspiration. Il évite que le flux d'air

n'éteigne les petites flammes.

9 AVERTISSEMENT

Pour réduire le risque de feu et pour

évacuer correctement l'air, évacuez

l'air vers l'extérieur. N'évacuez pas

l'air dans les murs, les plafonds, les

greniers, les vides sanitaires ou les

garages.

19

9 CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

9 AVERTISSEMENT

Pour réduire les risques de feu,

utiliser uniquement des gaines en

métal.

9 AVERTISSEMENT

Lorsque la hotte aspirante est

utilisée en mode d'évacuation d'air

simultanément avec un brûleur

différent utilisant également la même

cheminée, (tels des appareils de

chauffage au gaz, à l'huile ou au

charbon, des chauffe-eau

instantanés ou des chaudières à eau

chaude), veillez à ce que l'apport

d'air frais soit suffisant pour assurer

la combustion adéquate du brûleur.

Un fonctionnement sans risque est

possible si la sous-pression dans la

pièce où le brûleur est installé ne

dépasse pas 4 Pa (0,04 mbar).

On peut y parvenir en acheminant

l'air requis pour la combustion à

travers des ouvertures non

verrouillables, par exemple dans les

portes et fenêtres, et en association

avec des boîtiers muraux

d'admission/d'évacuation d'air fixées

au mur ou grâce à d'autres mesures

techniques telles qu'un verrouillage

réciproque, etc.

9 AVERTISSEMENT

Évitez l'intoxication au monoxyde de

carbone. – Prévoyez une admission

d'air adéquate pour empêcher

l'aspiration des gaz de combustion

dans la pièce.

Un boîtier mural air d'admission/air

d'échappement ne peut garantir que

la valeur limite ne sera pas

dépassée.

Remarque : Lorsque vous évaluez les

exigences globales, vous devez tenir

compte du système combiné d'aération

de la maison au complet. Cette règle ne

s'applique pas aux appareils de cuisson,

comme les surfaces de cuisson et les

fours.

9 ATTENTION

Appareil conçu exclusivement pour

la ventilation générale. Ne pas

utiliser pour évacuer des matières et

vapeurs dangereuses ou explosives.

Sécurité de manutention des

appareils

Cet appareil est lourd et il faut au moins

deux personnes ou l´équipement

approprié pour le déplacer.

Certaines surfaces peuvent

avoir des bords tranchants.

Faire attention en étendant le

bras derrière l’appareil ou en

dessous.

9 CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

20

9 AVERTISSEMENT

Risque de blessure !

Si l'appareil n'est pas correctement

fixé au mur, il risque de tomber. Tous

les éléments de fixation doivent être

montés solidement et de façon sûre.

9 AVERTISSEMENT

Risque de basculement !

L'appareil est très étroit et peut

basculer facilement. Ne pas poser

l'appareil à la verticale sur le sol.

Poser l'appareil à plat sur le sol.

Codes et normes de sécurité

Cet appareil est conforme aux plus

récentes versions de l'une ou plus des

normes suivantes :

▯ UL 507 - Ventilateurs électrique

(Electric Fans)

▯ CAN/CSA C22.2 No. 113 - Ventilateurs

et soufflantes (Fans and Ventilators)

Il incombe à l’installateur de déterminer

si des exigences et/ou normes

additionnelles s´appliquent pour des

installations spécifiques.

Sécurité électrique

9 AVERTISSEMENT

INSTRUCTIONS DE MISE À LA TERRE !

Cet appareil doit être mis à la terre.

En cas de court-circuit électrique, la

mise à la terre réduira le risque de

choc électrique en offrant au

courant électrique un fil

d'évacuation.

Cet appareil est muni d'un cordon

électrique comportant un

conducteur de terre et une prise de

mise à la terre. La fiche doit être

branchée dans une prise qui a été

installée et mise à la terre de façon

appropriée.

9 AVERTISSEMENT

Une mise à la terre inadéquate peut

entraîner un risque de choc

électrique. Consultez un électricien

qualifié si vous ne comprenez pas

parfaitement les instructions de mise

à la terre ou si vous avez des doutes

quant à la qualité de la mise à la

terre. N'utilisez pas de rallonge. Si

le cordon d'alimentation est trop

court, demandez à un

électricien d'installer une prise à

proximité de l'appareil. .

La page charge ...

Gaggenau VL 414 712 Manuel utilisateur

Ce manuel convient également à

Gaggenau VL 414 712 Manuel utilisateur

dans d''autres langues

Documents connexes