QUICK USER GUIDEQUICK USER GUIDE
Keep up with Wisycom online
Follow us on Facebook and Instagram.
You can also subscribe to our Youtube.
wisycom.com/social
Product Registration and Warranty
Register your product to extend your warranty
and receive update on latest rmware:
wisycom.com/registration
WISYCOM USA
5228 Eisenhower Avenue
Alexandria, VA 22304 - USA
+1 (888) WISYCOM
+1 (888) 947-9266
WISYCOM ITALY
Via Tiepolo 7/E
35019 Tombolo (PD) - ITALY
+39 0424 382605
This guide is intended to assist you with initial quick setup and operation
for your Wisycom product.
You can refer to Wisycom Autorized Distributors for technical Support and
information about service and repairs available in your area or contact us
directly by email.
Serial Number: Purchase Date:
Main Accesories (for an updated and exhaustive list look into wisycom web)
VAP20: carrying case
UPK Mini: infrared programming
interface. Use it with Wisycom Manager
available for free at www.wisycom.com
BAGPL2: carrying pouch
ISTR-MTB40S #MTB40S Quick user guide v1.02
Download Documentation and Firmware
Get latest user manual, tips, specications, rmware
& software on the download pages:
wisycom.com/products/d/MTB40S
(*)The Wisycom microphone pocket transmitter model MTB40S complies with the following requirements:
FCC (Federal Communications Commission) Part 74. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference recei-
ved, including interference that may cause undesired operations. Changes or modication not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC ID can be found inside the battery compartment.
(**) EN - This device operates on a no-protection, no-interference basis. Should the user seek to ob-
tain protection from other radio services operating in the same TV bands, a radio licence is required.
For further details, consult Innovation, Science and Economic Development Canada’s document Client
Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt Low-Power Radio Apparatus in
the TV Bands. This device complies with Industry Canada RSS-123. This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including interference that may cause undesired
operation of the device.
FR - Ce dispositif fonctionne selon un régime de non-brouillage et de non-protection. Si l’utilisateur devait
chercher à obtenir une certaine protection contre d’autres services radio fonctionnant dans les mêmes
bandes de télévision, une licence radio serait requise. Pour en savoir plus, veuillez consulter la Circulaire
des procédures concernant les clients CPC-2-1-28, Délivrance de licences sur une base volontaire pour
les appareils radio de faible puissance exempts de licence et exploités dans les bandes de télévision
d’Innovation, Sciences et Développement économique Canada. Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux appareils radio RSS-123. L’émetteur/récepteur exempt de li-
cence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes: 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionne-
ment.
Conformity
Europe
Conforms to the essential requirements of the RADIO Directive
2014/53/EU – Radio Equipment Directive (RED)
Japan
Certied Number: 202-SMD084 (model: MTB40S-JP)
Certied Number: 202-SMD085 (model: MTB40S-JP)
Certied Number: 001-A16237 (model: MTB40S-JB)
USA(*)
FCC-ID: POUMTB40SUSX (model: MTB40S-USX)
FCC-ID: POUMTB40SUS8 (model: MTB40S-US8)
Canada(**)
IC: 11967A-MTB40SUSX (model: MTB40S-USX)
IC: 11967A-MTB40SUS8 (model: MTB40S-US8)
MTB40S MTB40S
IR Port
To activate Infrared scroll up twice
from the main menu.
TIP: when you turn on the Tx, infrared
will be enabled automatically for 30
seconds.
High pass
lter
RF powerBattery status
Side view
Back view
Audio
max level (dBu)
or gain (dB)
Status Led
Power ON & Select
Keep pressed to turn on
the device.
Push to select and save
menu options.
Power OFF
Keep pressed
to switch off
the device.
Up and down arrows
Use the arrows to scroll into the MTB
menu.
CH/Gain shortcut
Push to access channel/group/
frequency menu. Make selection
with SEL button. Scroll through
the menu using the up/down
arrows to enter and adjust gain
in 1dB steps.
Batteries
Don’t forget to select battery type
installed within the options menu to
optimise battery life.
XLR mic input
Be sure you enable the
+48V via the menu to
work with condenser
microphones.
OFF: Transmitter is OFF
RED: RF power OFF/Transmitter ON
RED SLOW BLINK: battery < 25%
RED FAST BLINK: battery < 12%
RED FLASHES: modulation peak
GREEN: RF power is ON
BLUE: limiter is intervening
MTB40 16/2/21
MTB40 16/2/21
MTB40 16/2/21
-
1
-
2
