Briggs & Stratton 020700 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80027050 Revision -
Electric Pressure Washer
OPERATOR’S MANUAL
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® electric pressure washer. We are pleased that you’ve
placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this
manual, your Briggs & Stratton electric pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with electric pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this electric
pressure washer could be used for, it is important that you read and understand these instructions thoroughly before
attempting to start or operate this equipment. Save these original instructions for future reference.
This electric pressure washer requires final assembly before use. Refer to the Assembly section of this manual for
instructions on final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your electric pressure washer. There are over
30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact Briggs &
Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.
Electric Pressure Washer
Model Number _____________________________
Revision __________________________________
Serial Number ______________________________
Date Purchased ___________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
Table of Contents
Operator Safety.............................. 3
Assembly................................... 6
Features and Controls ........................ 8
Operation................................... 9
Maintenance ...............................12
Storage ...................................13
Troubleshooting ............................14
Warranty ..................................15
Specifications ..............................16
Register Your Product
To ensure prompt and complete warranty coverage, register your product online at www.onlineproductregistration.com.
Not for
Reproduction
3
Operator Safety
SAVE THESE INSTRUCTIONS
Equipment Description
This electric pressure washer operates at a maximum of
2,200 PSI with yellow spray tip and a flow rate of up to 1.2
GPM (gallons per minute) with turbo spray tip.
Every effort has been made to ensure that the information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve the
product and this document at any time without prior notice.
This ISM device complies with Canadian ICES-001.
Ground Fault Circuit Interrupter Protection
This pressure washer is provided with a ground-fault
circuit-interrupter (GFCI) built into the plug of the power
supply cord. This device provides additional protection
from the risk of electric shock. Should replacement of
the plug or cord become necessary, use only identical
replacement parts that include GFCI protection.
Automatic Shut-Off
The electric pressure washer is equipped with a sensor
that will detect that water flow has stopped when releasing
or locking the spray gun trigger. The sensor will cause the
motor to shut off for as long as the spray gun trigger is
released or locked.
If the motor continues to run when the spray gun trigger is
released or locked, DO NOT USE THE MACHINE. Call the
electric pressure washer helpline at (800) 743-4115 for
assistance.
NOTICE The electric pressure washer is equipped with a
main power ON/OFF switch. The switch should always be
moved to the OFF position (0) when the electric pressure
washer is not being used to prevent possible damage.
Motor Overload
The electric motor in this electric pressure washer is
equipped with an overload protection device (thermostat).
This device will automatically shut off the motor if the motor
overheats or draws excessive current.
If the overload protection device is tripped, disconnect the
power supply by turning the master ON/OFF switch to the
OFF (0) position. Let unit cool for 30 minutes. Then turn
the master ON/OFF switch to the ON (I) position to resume
operation.
Important Safety Information
Please read and understand this entire manual before
attempting to assemble, operate or service the product.
Follow the maintenance instructions specified in this manual.
If you have any questions regarding the product, please call
customer service at (800) 743-4115, 8 a.m. - 5 p.m., CST,
Monday - Friday.
Safety Symbols and Meanings
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol
may be used to represent the type of hazard. The signal
word NOTICE indicates information considered important,
but not hazard-related.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates information considered important, but
not hazard-related.
WARNING Failure to read and follow the operator’s
manual and all operating instructions before
using could result in death or serious injury.
• Read this manual carefully and become familiar with
your electric pressure washer. Know its applications, its
limitations, and any hazards involved.
Chemical Burn
Electrical Shock
Slippery Surface Fall
Flying Objects
Read Manual
Projectile
Fluid Injection
Fire
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
WARNING Use of electric pressure washer could
create puddles and slippery surfaces.
Risk of kickback. Spray gun could
kickback causing you to fall resulting in
death or serious injury.
• Operate the electric pressure washer from a
stable surface.
• Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
• The cleaning area should have adequate slopes
and drainage to reduce the possibility of a fall due to
slippery surfaces.
• Be extremely careful if you must use the electric
pressure washer from a ladder, scaffolding, or any
other similar location.
• Firmly grasp spray gun with both hands when using
power spray modes to avoid injury when spray gun
kicks back.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• NEVER aim spray gun at people, animals, or plants.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
WARNING Risk of eye or bodily injury. Spray could
splash back, propel objects or cause
internal harm resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment. NEVER substitute safety
glasses or dry-condition goggles for indirect vented
safety goggles.
• Know how to stop the pressure washer and bleed
pressure quickly. Be thoroughly familiar with the
controls.
• DO NOT allow CHILDREN to operate the electric
pressure washer.
• Keep operating area clear of all persons.
• Inspect high pressure hose before each use. NEVER
repair high pressure hose; replace it.
• DO NOT repair leaking connections with sealant of any
kind; replace o-rings and gaskets.
• Keep hose connected to electric pressure washer and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction while system
is pressurized and squeeze spray gun trigger to release
high pressure, every time you turn off the pressure
washer.
• DO NOT aim spray gun at people or animals.
• DO NOT
drink from hose connected accessories.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while the electric
pressure washer is in ON (I) position.
• DO NOT use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun and accessories are
correctly attached.
• Stay alert – watch what you are doing.
• DO NOT operate the product when fatigued or under
the influence of alcohol or drugs.
• Close supervision is necessary when this product is
used near children.
WARNING Risk of electrocution. Use of an
extension cord could cause electric shock or
burn resulting in death or serious injury.
• DO NOT use an extension cord with this electric
pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving
ground-fault circuit-interruption protection.
WARNING Risk of electrocution. Contacting both
power conductors, at the same time could
cause electric shock or burn resulting in death
or serious injury.
• Connect only to a properly grounded outlet. DO NOT
remove ground pin from plug.
• Inspect cord before each use, DO NOT use if cord is
damaged.
• The product is equipped with a ground fault circuit
interrupter (GFCI) built into the power cord plug. If
replacement of the plug or cord is required, use only
identical replacement parts.
• Keep all connections dry and off the ground.
• DO NOT touch plug with wet hands.
• DO NOT run cord through doorways, windows, holes in
ceilings, walls, or floors.
• DO NOT walk on cord.
• DO NOT drive over, drag or place objects over cord.
• DO NOT spray near power source.
Not for
Reproduction
5
NOTICE High pressure spray could damage fragile
items including glass.
• DO NOT point spray gun at glass when using turbo
spray tip.
• NEVER aim spray gun at plants.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump
and spray gun rendering your unit inoperable.
• Freeze damage is not covered under warranty.
NOTICE Improper treatment of electric pressure washer
could damage it and shorten its life.
• If you have questions about intended use, ask dealer or
contact authorized service center.
• DO NOT operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by-pass any safety device on the electric
pressure washer.
• DO NOT modify the electric pressure washer in any
way.
• Before starting the electric pressure washer in cold
weather, check all parts of the equipment to be sure ice
has not formed there.
• DO NOT move the electric pressure washer by pulling
on hoses. Move unit using the transport handle
supplied.
• Use ONLY branded accessories intended for use with
this product.
WARNING Risk of fire. Spraying flammable liquids
could result in death or serious injury.
• DO NOT spray flammable liquids.
WARNING Risk of fire. Overheated cord could result
in death or serious injury.
• Uncoil cord completely prior to use.
• DO NOT cover cord with any material.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting
in death or serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
chemicals.
• DO NOT substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• DO NOT use caustic liquid with electric pressure
washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING This product contains lead and lead
compounds, known to the state of California to cause
birth defects or other reproductive harm. Wash your
hands after handling this product. Cancer and
Reproductive Harm - www.P65Warnings.ca.gov
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Assembly
Read entire Operator’s Manual before you
attempt to assemble or operate your new
electric pressure washer.
Your electric pressure washer requires some assembly
but is quickly ready for use. If you have any problems with
the assembly of your electric pressure washer, please call
the electric pressure washer helpline at (800) 743-4115. If
calling for assistance, please have the model, revision, and
serial number from the identification label available.
Tools Needed
• Philips screwdriver #2
Unpack Electric Pressure Washer
1. Remove everything from carton.
2. Ensure you have all included items prior to assembly.
Items Included in the Carton
• Main unit
• Handle with accessory tray
• Spray gun
• High pressure hose
• Spray wand
• Quick Connect (QC) spray tips (3)
• Quick Connect (QC) foamer spray tip with detergent
bottle
• Handle support tubes (2)
• Screws (2)
• Operator’s Manual
Check all contents. If any parts are missing or damaged,
DO NOT use, call the electric pressure washer helpline at
(800) 743-4115.
Become familiar with each component before assembling
the electric pressure washer. Identify contents with the
illustration shown in Features and Controls.
Attach Handle and Support Tubes
1. Push and hold lock-pin buttons (A) on each side of
the handle. Slide handle (B) down into each handle
support tubes (C) until lock-pins buttons snap into the
holes.
2. Slide handle support tubes (C) into slots on both
sides of main unit. Align holes and insert screws (D).
Tighten with a #2 philips screwdriver.
Lubricate O-Rings
Lubrication of o-rings is extremely important for installation
and operation. The use of a lubricant (petroleum or
synthetic grease) during assembly helps seat o-rings
properly and provides an improved seal. It also helps
protect the o-ring from damage by abrasion, pinching or
cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant on
o-rings prior to assembling the garden hose to the pump
(E), high pressure hose (F), spray gun (G), and spray
wand (H).
Lubricate all connections shown below, following
these instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light film
is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible (QC
fitting, M22 fitting).
H
G
E
F
A
B
C
D
C
D
Not for
Reproduction
7
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water supply
connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
1. Uncoil high pressure hose (A) and attach black end of
hose to base of spray gun (B). Tighten by hand.
2. Attach red end of high pressure hose (A) to high
pressure outlet (C) on pump. Tighten by hand.
3. Run water through your garden hose for 30 seconds
to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F (38°C)).
4. Before connecting garden hose (D) to water inlet (E),
inspect inlet screen (F). Clean screen if it contains
debris or have it replaced if damaged. DO NOT run
pressure washer if inlet screen is damaged.
NOTICE Using a One Way Valve (vacuum breaker or
check valve) at pump inlet could cause pump or inlet
connector damage.
• There MUST be at least 10 ft. (3 m) of unrestricted
garden hose between the pressure washer inlet and any
device, such as a vacuum breaker or check valve.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Connect the garden hose (D) (not to exceed 50 ft. (15
m) in length) to the water inlet (E). Tighten by hand.
6. Turn ON the water, press red button (G) on the gun
and squeeze the trigger to purge the pump system of
air and impurities.
Checklist Before Starting Pump Motor
Review the unit’s assembly to ensure you have performed
all of the following.
1. Be sure to read Operator Safety and Operation before
using the electric pressure washer.
2. Check for properly tightened hose connections.
3. Check to make sure there are no kinks, cuts, or damage
to hoses.
4. Provide a proper water supply at an adequate flow.
5. Plug electrical power cord into a dedicated electrical circuit
rated for 120 Volts AC at 15 Amps that is properly installed
in accordance with all local codes and ordinances. Check
that circuit is not used to supply any other electrical needs.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER connect high pressure hose to spray wand.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when
using or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
G
C
A
B
A
E
D
F
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Features and Controls
Read the Operator’s Manual and safety rules before operating your electric pressure washer.
Compare the illustrations with your electric pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this original manual for future reference.
A - Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes trigger lock.
B - Spray Tips — Yellow and white spray tips are for
various high pressure applications.
C - High Pressure Hose — Connect red end to high
pressure water outlet and black end to spray gun.
D -Warning Label — Identifies hazards to be avoided
when using your pressure washer.
E - Master ON/OFF Toggle Switch — Push top of switch
in (I) to turn pressure washer ON. Push bottom of switch
in (0) to turn pressure washer OFF.
F - Water Supply Inlet — Connect to water supply using a
50 ft. (15.24 m) maximum garden hose.
G - Electric Cord with GFCI — The electric pressure
washer and operator is protected by a ground fault
circuit interrupter (GFCI).
H - Foamer Spray Tip with Detergent Bottle — Use to
apply pressure washer safe detergent to surfaces.
J - Identification Label (under housing)— Provides model
and serial number of pressure washer. Please have
these readily available if calling for assistance.
K - High Pressure Outlet — Connection for high pressure
hose.
L - Spray Wand — Allows you to switch between different
spray tips.
M -Turbo Spray Tip — Whirls a powerful pin-point jet of
water for intense cleaning.
C
A
L
K
M
F
H
J
D
E
G
B
Not for
Reproduction
9
Operation
How to Start Your Electric Pressure Washer
Follow the instructions below in the order presented. If
you have any problems operating your electric pressure
washer, please call the electric pressure washer helpline at
(800) 743-4115.
1. Place pressure washer near an outside water source
capable of supplying water at a flow rate greater than
3.0 gallons (11.4 l) per minute and no less than 20 PSI
(1.3 BAR) at pressure washer end of garden hose. DO
NOT siphon supply water.
2. Check that high pressure hose is tightly connected to
spray gun and pump. See Assembly section.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
NOTICE DO NOT run the pump without the water supply
connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Turn ON water, point gun in a safe direction, press red
button and squeeze trigger to purge pump system of air
and impurities.
6. Attach spray wand to spray gun. Tighten by hand.
7. Choose spray tip you want to use, pull back on collar
of spray wand, insert spray tip and release collar. Tug
on spray tip to make sure it is securely in place. See
How to Use Spray Tips.
8. Push master ON/OFF switch (A) to OFF (0) position.
9. Plug electrical power cord into a dedicated electrical
circuit rated for 120 Volts AC at 15 Amps that is
properly installed in accordance with all local codes and
ordinances. Circuit is not to supply any other electrical
needs. The indicator light on the GFCI should be ON.
NOTICE The indicator light must be ON for the electric
pressure washer to operate.
10. Press TEST button (B). The indicator light (C) should
be OFF.
11. Press RESET button (D). The indicator light (C)
should be ON.
NOTICE DO NOT use the electric pressure washer if
above test fails.
12. Press the master ON/OFF switch (A) to the pressure
washer ON (I) position.
13. Point gun in a safe direction, press trigger lock button
and squeeze trigger.
The electric pressure washer motor will start and stop as
spray gun trigger is depressed and released.
The electric pressure washer is now ready for use.
Instructions for use of the supplied accessories are given
later in this section.
WARNING Risk of electrocution. Non-operating
ground fault circuit interrupter (GFCI) could
result in death or bodily injury. If indicator light
does not stay ON after test and reset, do not
use GFCI.
A
WARNING Risk of electrocution. Use of an
extension cord could cause electric shock or
burn resulting in death or serious injury.
• DO NOT use an extension cord with this electric
pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving
ground-fault circuit-interruption protection.
B
D
C
WARNING Risk of eye injury. Spray could splash
back or propel objects resulting in serious
injury. Always wear indirect vented (chemical
splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
How to Stop Your Electric Pressure Washer
The electric pressure washer motor runs only when the
trigger is engaged. To stop the electric pressure washer
and turn off the motor:
1. Release spray gun trigger.
2. Press the master ON/OFF switch to the OFF (0) position.
NOTICE Releasing the trigger will shut off the motor but
does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction, press
trigger lock button and squeeze trigger to relieve built
up pressure in the unit.
5. Disconnect GFCI plug from outlet.
How to Use Spray Tips
There are four spray tips supplied with the pressure
washer. The turbo spray tip whirls a powerful pin-point jet
of water for intense cleaning. The yellow and white spray
tips are for various high pressure applications. The foamer
spray tip is for general soap applications.
Usage Tips
• For most effective cleaning, keep spray tip from 8 to
24 inches away from cleaning surface.
• If you get spray tip too close, especially using a high
pressure spray tip, you may damage surface being
cleaned.
• DO NOT get closer than 6 inches when cleaning tires.
Applying Detergent
To apply detergent, follow these steps:
1. Install foamer spray tip with detergent bottle.
2. Prepare detergent solution as required by job.
3. Rotate detergent bottle (A) counter-clockwise and
remove from foamer spray tip (B).
4. Fill bottle with detergent solution.
5. Reinstall detergent bottle onto foamer spray tip and
turn clockwise until it clicks into place.
6. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray
gun and high pressure outlet. Turn on water.
NOTICE You must attach all hoses before you start the
pressure washer.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• Keep high pressure hose connected to pump and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting
in death or serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
chemicals.
• DO NOT substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• DO NOT use caustic liquid with electric pressure
washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
Low Pressure
Foamer
Use to apply
detergent
Delicate Rinse
White, 40°
Cars / Vans /
Trucks / Outdoor
Furniture
1300 PSI (90 bar)
1.1 GPM (4.1 LPM)
General Rinse
Yellow, 15°
Siding / Patios
Decks /
Driveways / Garage Floors
2200 PSI (152 bar)
1.0 GPM (3.7 LPM)
Intense Cleaning
Turbo
Paint Removal /
Oil Stains / Rust
Removal
900 PSI (6 bar)
1.2 GPM (4.5 LPM)
B
A
Not for
Reproduction
11
WARNING Risk of kickback.
Spray gun could kickback causing you to fall
resulting in death or serious injury.
• Operate the electric pressure washer from a
stable surface.
• Be extremely careful if you must use the electric
pressure washer from a ladder, scaffolding, or any
other similar location.
• Firmly grasp spray gun with both hands when using
power spray modes to avoid injury when spray gun
kicks back.
7. Start the pressure washer as instructed in How to
Start Your Electric Pressure Washer.
8. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward using
long, even, overlapping strokes.
9. Allow detergent to “soak in” for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. To prevent streaking, do not allow
detergent to dry on surface.
Electric Pressure Washer Rinsing
1. Remove foamer spray tip from wand.
2. Install white or yellow spray tip.
3. Keep spray gun a safe distance from area you plan to
spray.
4. Apply a high pressure spray to a small area and then
check surface for damage. If no damage is found, you
can assume it is okay to continue rinsing.
5. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Other Cleaning Tips
• NEVER leave the electric pressure washer unattended
while it is plugged into an electrical outlet and while
water is supplied to the equipment.
• If you have the spray tip too far away from the surface
being washed, the cleaning may not be as effective.
How to Store Accessories
The unit is equipped with areas to store your high pressure
hose, spray gun, spray wand, and power cord. Coil power
cord on brackets on ends of main unit. Wrap high pressure
hose and store on hook on back of accessory tray. Store
spray gun in slots on left side of accessory tray. Snap
spray wand in slots on right side of accessory tray. Store
spray tips in holes on front of accessory tray. Identify all
accessories with the illustrations in Features and Controls.
Not for
Reproduction
12 BRIGGSandSTRATTON.COM
Maintenance
General Recommendations
Regular maintenance will improve the performance and
extend the life of the electric pressure washer.
The electric pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty, the
operator must maintain the electric pressure washer as
instructed in this manual, including proper storage.
NOTICE Should you have questions about replacing
components on your electric pressure washer, please call
(800) 743-4115 for assistance.
Before Each Use
1. Clean debris.
2. Check water inlet screen for debris or damage.
3. Check high pressure hose for leaks.
4. Check spray gun operation.
Electric Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from electric
pressure washer. Inspect cooling air slots and openings on
the front, rear and bottom of the electric pressure washer.
These openings must be kept clean and unobstructed.
The electric pressure washer parts should be kept clean to
reduce the risk of overheating and ignition of accumulated
debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of the electric pressure
washer can damage it and/or shorten its life.
• DO NOT insert any objects through cooling slots.
Check and Clean Water Inlet Screen
Examine the screen on the unit’s water inlet. Clean it if the
screen is clogged or replace it if screen is damaged.
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using it. Check for cuts, leaks, abrasions or bulging of
cover, damage or movement of couplings. If any of these
conditions exist, replace the hose immediately.
Check Spray Gun
Examine the hose connection to the spray gun and
make sure it is secure. Test the trigger (A) by pressing
the triggger lock button (B) and making sure the trigger
“springs back” into place when you release it. You should
not be able to press the trigger without pressing the trigger
lock button. Replace spray gun immediately if it fails any of
these tests.
B
Spray Tip Maintenance
Excessive pump pressure can cause a pulsing sensation
felt while squeezing the spray gun trigger. The principal
cause of excessive pump pressure is a spray tip clogged or
restricted with foreign materials such as dirt, etc. A clogged
spray tip could lead to pump cycling ON/OFF or not turning
on even when there is some flow.
1. Press the master ON/OFF switch to the OFF (0)
position. Remove power cord plug from electrical outlet.
2. Disconnect water supply at the electric pressure
washer.
3. ALWAYS point spray gun in a safe direction, press
trigger lock button and squeeze spray gun trigger to
release retained high water pressure.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when motor
is stopped and water is disconnected, which could result
in serious injury.
• Keep high pressure hose connected to pump and
spray gun while system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze
spray gun trigger to release high pressure, every time
you turn off pressure washer.
A
Not for
Reproduction
13
4. Remove spray tip from end of spray wand.
5. Use a small paper clip to free any foreign material
clogging or restricting any of the spray tips.
6. Using a garden hose, remove additional debris by
back flushing water through spray wand. Back flush
between 30 to 60 seconds.
7. Reinstall spray tip into spray wand.
8. Reconnect spray wand to spray gun.
9. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray
gun. Turn on water.
10. Plug power cord into electrical outlet and press the
master ON/OFF switch to the pressure washer ON (I)
position.
11. Test the electric pressure washer by operating with
each spray tip.
Pump and Motor Maintenance
The electric pressure washer does not require any
maintenance to the pump or motor. Both assemblies
are pre-lubricated and sealed, requiring no additional
lubrication ever.
After Each Use
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and “freeze”
pump action. Follow these procedures after every use:
1. Flush detergent bottle (if used) by removing it from the
foamer spray tip and pouring out all remaining solution.
2. Rinse detergent bottle out with fresh clean water and
reinstall onto foamer spray tip.
3. Run the electric pressure washer with foamer spray
tip. Flush for one or two minutes.
4. Press the master ON/OFF switch to the OFF (0) position.
5. Turn off water supply, point gun in a safe direction,
press red button and squeeze trigger to relieve trapped
pressure, and let engine cool.
6. Disconnect hose from spray gun and high pressure
outlet on pump. Drain water from hose, spray gun,
and spray wand. Use a rag to wipe off the hose.
7. Drain water from pump by tipping unit to the side (water
inlet facing down) for two minutes. Tip to the other side
(high pressure outlet facing down) for an additional two
minutes.
8. Wrap high pressure and store on hook on back of
accessory tray.
9. Coil power cord on brackets.
10. Store spray gun and spray wand in slots on accessory
tray. Store spray tips in holes on accessory tray.
11. Store unit in a clean, dry area.
12. If storing for more than 30 days see Winter or Long
Term Storage.
Winter or Long Term Storage
Follow steps 1-10 in After Each Use.
NOTICE Water left in pump could freeze and permanently
damage pump. Freeze damage is not covered under
warranty.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver, Model 6039, to treat
pump. This prevents freeze damage and lubricates plunger
and seals.
NOTICE PumpSaver is available as an optional
accessory. It is not included with the electric pressure
washer. Contact the nearest authorized service center to
purchase Pump Saver.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump
and spray gun rendering your product inoperable.
• Freeze damage is not covered under warranty.
To use PumpSaver, make sure the electric pressure
washer is turned off and inlet and outlet hoses are
disconnected. Read and follow all instructions and
warnings given on the PumpSaver container.
Final Storage Procedures
1. Wrap high pressure and store on hook on back of
accessory tray.
2. Coil power cord on brackets.
3. Store spray gun and spray wand in slots on accessory
tray. Store spray tips in holes on accessory tray.
4. Store unit in a clean, dry area that is protected from
freezing temperatures.
5. Cover unit with a suitable protective cover that does
not retain moisture.
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
Troubleshooting
Problem Cause Correction
Pump has following
problems: failure to produce
pressure, erratic pressure,
chattering, loss of pressure,
low water volume.
1. Water inlet is blocked.
2. Inadequate water supply.
3. Garden hose is kinked or leaking.
4. Clogged water inlet screen.
5. Water supply is over 100°F (38°C).
6. High pressure hose is blocked or
leaks.
7. Spray tip is obstructed.
1. Clear inlet.
2. Provide adequate water flow.
3. Straighten garden hose or replace if leaking.
4. Check and clean water inlet screen.
5. Provide cooler water supply.
6. Clear blocks in high pressure hose or
replace hose.
7. Clean spray tip.
Unit fails to start when spray
gun trigger is squeezed.
1. Water supply is not turned on.
2. Unit is not turned on.
3. Garden hose is too long.
4. Fuse blown or circuit breaker tripped.
1. Turn on water supply.
2. Press the master ON/OFF switch to the
ON (I) position. Reset GFCI.
3. Use only 50 ft. (15.24 m) maximum
garden hose.
4. a.) Check fuse box for blown fuse and
replace as necessary or reset circuit
breaker. Do not use a fuse or circuit
breaker with a higher rating than that
specified for your particular branch
circuit.
b.) Disconnect other electrical
appliances and turn off lights in the
circuit or operate the pressure washer
on its own dedicated circuit.
c.) Run pressure washer with any spray
tip for 5 minutes. Motor break in may be
necessary.
Detergent fails to mix with
spray.
1. High pressure spray tip is installed. 1. Install foamer spray tip.
Hose connections leaking.
1. Garden hose loose to water inlet.
2. Loose high pressure hose
connections.
3. Damaged o-ring.
1. Hand tighten garden hose to water
inlet.
2. Remove hose completely and reinstall
hand tight.
3. Replace o-ring.
For all other issues, see a Briggs & Stratton authorized dealer.
Not for
Reproduction
15
80018419_EN Rev A
BRIGGS & STRATTON WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and
is subject to the time periods and conditions stated below. For warranty service, contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the
internet at BRIGGSANDSTRATTON.COM.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the
warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion
is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial
use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty covers only defects in materials or
workmanship. It does not cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
12 months None
Not for
Reproduction
16 BRIGGSandSTRATTON.COM
Specifications
Max Pressure ...............2,200 PSI (152 BAR)* @ 1.0 GPM (3.8 liters/min)
Max Flow Rate .................1.2 GPM (4.5 liters/min)* @ 900 PSI (62 BAR)
Detergent Mix .................................... See MFR’s Instructions
Water Supply Temperature ........................41°F (5°C) - 100°F (38°C)
Motor ...................................................Induction Type
Rated Voltage ............................................. 120 Volts AC
Current..................................................... 14.5 Amps
Briggs & Stratton Corporation
P.O. Box 702
Milwaukee, Wisconsin, 53201-0702 U.S.A.
(800) 743-4115
Electric Pressure Washer
*
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard
PW101-2010 (Testing and Rating Performance of Pressure Washers).
Not for
Reproduction
Esta limpiadora a presión está clasificada conforme a la norma PW101-2010
(Comprobación y Clasificación de Rendimiento de Limpiadoras a Presión) de la
Asociación de Fabricantes de Limpiadoras a Presión (PWMA).
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, EE. UU.
Hidrolavadora eléctrica
MANUAL DEL OPERARIO
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Gracias por comprar esta hidrolavadora eléctrica Briggs & Stratton® de alta calidad. Nos complace que haya depositado
su confianza en la marca Briggs & Stratton. Si la operación y el mantenimiento de su producto Briggs & Stratton se realiza
según las instrucciones de este manual, le proporcionará muchos años de servicio confiable.
Este manual contiene información de seguridad para alertarlo sobre los peligros y riesgos asociados con las
hidrolavadoras eléctricas, y para indicarle cómo evitarlos. Dado que Briggs & Stratton no conoce necesariamente todas
las aplicaciones para las cuales se podría utilizar esta hidrolavadora eléctrica, es importante que usted lea detalladamente
y entienda estas instrucciones antes de hacer arrancar o utilizar este equipo. Guarde estas instrucciones originales
para futuras consultas.
Esta hidrolavadora eléctrica requiere su montaje final antes de su uso. Consulte la sección Montaje de este manual
para conocer las instrucciones sobre los procedimientos de montaje final. Siga las instrucciones detalladamente.
Contacto
Nunca debe ir demasiado lejos para encontrar el soporte y el servicio de Briggs & Stratton para su hidrolavadora eléctrica.
Existen más de 30.000 distribuidores de servicio autorizado por Briggs & Stratton en todo el mundo, quienes suministran
servicio de calidad. También puede ponerse en contacto con Atención al Cliente de Briggs & Stratton por teléfono al (800)
743-4115 o en Internet en BRIGGSandSTRATTON.COM.
Hidrolavadora eléctrica
Número de modelo __________________________
Revisión __________________________________
Número de serie ____________________________
Fecha de compra __________________________
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. Reservados todos los derechos.
Índice
Seguridad del operador . . . . . . . . . . . . . . . . . . . . . . . 3
Montaje .................................... 6
Características y controles..................... 8
Operación .................................. 9
Mantenimiento .............................12
Almacenamiento............................14
Solución de problemas.......................15
Garantía...................................16
Especificaciones............................18
Registrar su producto
Para asegurar pronta y completa cobertura de la garantía, registre su producto en línea en
www.onlineproductregistration.com.
Not for
Reproduction
3
Seguridad del operador
CONSERVE ESTAS INSTRUCCIONES
Descripción del equipo
Esta lavadora de presión eléctrica opera a un máximo
de 152 bar (2200 PSI) con una punta de pulverización
amarilla y a un caudal de hasta 4.5 LPM (litros) (1,2 GPM
(galones)) por minuto con una punta de pulverización
turbo.
Hemos hecho todo lo posible para asegurarnos de que la
información de este manual sea precisa y esté actualizada.
No obstante, nos reservamos el derecho a cambiar,
modificar o mejorar el producto y este documento en
cualquier momento y sin previo aviso.
Este dispositivo ISM cumple con la norma canadiense
ICES-001.
Circuitos protegidos con interruptores a tierra
Esta arandela de presión se proporciona con un circuito
protegido con interruptores a tierra (GFCI) integrado en
el enchufe del cable de alimentación. Este dispositivo
aporta una mayor protección frente al riesgo de descarga
eléctrica. En el caso de que sea necesario sustituir
el enchufe o el cable, utilice piezas de repuestos
exactamente idénticas que dispongan de protección GFCI.
Apagado automático
La hidrolavadora eléctrica está equipada con un sensor
que detectará si el flujo de agua se detuvo al activar o
bloquear el gatillo de la pistola pulverizadora. El sensor
hará que el motor se apague siempre que el gatillo de la
pistola pulverizadora se active o bloquee.
Si el motor continúa en funcionamiento cuando se activa o
bloquea el gatillo de la pistola pulverizadora, NO USE LA
MÁQUINA. Llame al teléfono de ayuda de la hidrolavadora
eléctrica: (800) 743-4115 para obtener asistencia.
AVISO La hidrolavadora eléctrica está equipada con
un interruptor de encendido/apagado de la alimentación
principal. El interruptor siempre debe estar en la posición
de apagado (0) cuando no se usa la hidrolavadora
eléctrica para evitar probables daños.
Sobrecarga del motor
El motor eléctrico de esta hidrolavadora eléctrica está
equipado con un dispositivo de protección por sobrecarga
(termostato). Este dispositivo apagará automáticamente el
motor si este se recalienta o utiliza corriente en exceso.
Si se activa el dispositivo de protección por sobrecarga,
desconecte la alimentación. Para ello, coloque el
interruptor principal de encendido/apagado en la posición
de apagado (0). Deje que la unidad se enfríe durante
30 minutos. Luego, coloque el interruptor principal de
encendido/apagado en la posición de encendido (I) para
continuar con el funcionamiento.
Información de seguridad importante
Lea y comprenda todo el manual antes de armar,
hacer funcionar o realizar operaciones de reparación/
mantenimiento en el producto. Siga las instrucciones de
mantenimiento especificadas en este manual. Si tiene
alguna pregunta relacionada con este producto, por favor,
póngase en contacto con el servicio de atención llamando
al cliente al (800) 743-4115, de lunes a viernes, de 8.00 a
17.00, CST.
Símbolos de seguridad y significados
El símbolo de alerta de seguridad indica un posible
riesgo para su integridad física. Se utiliza una palabra de
señalización (PELIGRO, ADVERTENCIA o PRECAUCIÓN)
junto con el símbolo de alerta para designar un grado o
nivel de gravedad de riesgo. Se puede utilizar un símbolo
de seguridad para representar el tipo de riesgo. AVISO
indica una información considerada importante, pero no
relacionada con un peligro potencial.
PELIGRO indica un peligro que, si no se evita,
ocasionará la muerte o una lesión grave.
ADVERTENCIA indica un peligro que, si no se evita,
podría ocasionar la muerte o una lesión grave.
PRECAUCIÓN indica un peligro que, si no se evita,
podría ocasionar en lesión leve o moderada.
AVISO indica una información considerada importante, pero
no relacionada con un peligro potencial.
ADVERTENCIA No leer ni seguir las instrucciones del
manual del operador y todas las instrucciones de
funcionamiento antes de usar la unidad podría
ocasionar la muerte o lesiones graves.
• Lea este manual cuidadosamente y familiarícese con la
hidrolavadora eléctrica. Conozca sus aplicaciones, sus
limitaciones y los peligros involucrados.
Quemadura
química
Descarga eléctrica
Superficie
resbaladiza
Caídas
Objetos
voladores
Lea el manual
Proyectil
Inyección
de fluidos
Fuego
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
ADVERTENCIA El uso de la hidrolavadora eléctrica
podría formar charcos y generar
superficies resbaladizas.
Riesgo de contragolpe. La pistola de
pulverización podría causar un contragolpe, con riesgo de
caída que podría provocar la muerte o lesiones graves.
• Opere la hidrolavadora eléctrica desde una superficie
estable.
• No se estire ni se pare sobre un apoyo inestable.
Mantenga una postura firme y un buen equilibrio en
todo momento.
• La zona de limpieza debe tener inclinaciones
adecuadas y sistema de drenaje para reducir la
posibilidad de caída debido a superficies resbaladizas.
• Sea extremadamente cuidadoso si debe usar la
hidrolavadora eléctrica desde una escalera, un
andamio u otro lugar similar.
• Sujete firmemente la pistola de pulverización con
ambas manos al utilizar modos de pulverización
eléctrica para evitar lesiones en caso de contragolpe de
la pistola.
ADVERTENCIA El chorro de agua a alta presión que
este equipo produce podría atravesar la piel y
los tejidos subcutáneos, y provocar lesiones
graves y posible amputación.
La pistola de pulverización acumula agua a alta
presión, incluso con el motor detenido y el agua
desconectada, lo que puede provocar lesiones graves.
• NUNCA apunte la pistola de pulverización hacia
personas, animales o plantas.
• SIEMPRE apunte con la pistola de pulverización hacia
una dirección segura y apriete el gatillo de la pistola
para liberar la alta presión, cada vez que apague la
hidrolavadora.
ADVERTENCIA Riesgo de lesiones oculares o
corporales. La pulverización podría
salpicar, propulsar objetos o causar
daños internos, lo que puede provocar
lesiones graves.
• Siempre use gafas de seguridad con ventilación indirecta
(salpicaduras de productos químicos) identificadas en
cumplimiento de la norma ANSI Z87.1 cuando utilice
este equipo o esté cerca de él. NUNCA sustituya las
gafas de seguridad con ventilación indirecta con gafas de
seguridad o gafas de condición seca.
• Sepa cómo detener la hidrolavadora y descargar la
presión rápidamente. Familiarícese completamente con
los controles.
• NO permita que ningún NIÑO opere la hidrolavadora
eléctrica.
• Mantenga el área de operación libre de personas.
• Inspeccione la manguera de alta presión antes de
cada uso. NUNCA repare la manguera de alta presión;
reemplácela.
• NO repare las conexiones con fugas con sellador de
ningún tipo; reemplace las juntas tóricas y juntas.
• Mantenga la manguera conectada a la hidrolavadora
eléctrica y a la pistola de pulverización cuando el
sistema esté presurizado.
• SIEMPRE apunte con la pistola de pulverización
hacia una dirección segura mientras el sistema esté
presurizado y apriete el gatillo de la pistola para liberar
la alta presión, cada vez que apague la hidrolavadora.
• NO apunte la pistola de pulverización hacia personas o
animales.
• NO beba de los accesorios conectados a la manguera.
• NO fije la pistola de pulverización en la posición abierta.
• NO deje la pistola de pulverización desatendida
cuando la hidrolavadora eléctrica está en la posición de
encendido (I).
• NO utilice una pistola de pulverización que no tenga
un bloqueo o seguro de gatillo instalado y en buenas
condiciones.
• Asegúrese siempre de que la pistola de pulverización y
los accesorios estén conectados correctamente.
• Manténgase alerta, observe lo que está haciendo.
• NO haga funcionar el producto si está cansado o bajo
la influencia de alcohol o drogas.
• Se requiere supervisión minuciosa cuando este
producto se utiliza cerca de niños.
ADVERTENCIA Riesgo de electrocución.
El contacto con ambos conductores de
alimentación al mismo tiempo podría ocasionar
descarga eléctrica o quemaduras que pueden
provocar lesiones graves o la muerte.
• Conectarla solo a un toma corriente con una buena
descarga a tierra. NO quite el terminal de tierra del enchufe.
• Inspeccione el cable antes de cada uso, NO lo utilice si
está dañado.
• El producto está equipado con un interruptor de circuito
por fallos con conexión a tierra (GFCI) montado en el
enchufe del cable de alimentación. Si es necesario
cambiar el enchufe o el cable, utilice solamente piezas
de repuesto idénticas.
• Mantenga todas las conexiones secas y alejadas del
suelo.
• NO toque el enchufe con las manos mojadas.
• NO pase el cable a través de puertas, ventanas,
agujeros en los techos, paredes o pisos.
• NO camine sobre el cable.
• NO conduzca sobre el cable ni arrastre o coloque
objetos sobre él.
• NO pulverice cerca de una fuente de alimentación.
ADVERTENCIA Riesgo de electrocución. El uso
de un cable de prolongación podría ocasionar
descarga eléctrica o quemaduras que pueden
provocar lesiones graves o la muerte.
• NO use un cable de prolongación con esta
hidrolavadora eléctrica. Es posible que el cable de
prolongación o el enchufe del circuito eléctrico de su
casa no proporcione la protección del interruptor de
circuito por fallos con conexión a tierra que resguarda
la vida de las personas.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Briggs & Stratton 020700 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
Simplicity 020681-00 Guide d'installation
-
-
-
-
-