Gaggenau Deals RY492701 Guide d'installation

Gaggenau

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES DE INSTALACIÓN

RY 492

2

INSTALLATION INSTRUCTIONS ............ 3

INSTRUCTIONS D’INSTALLATION ........ 28

INSTRUCCIONES DE INSTALACIÓN ..... 56

3

Content

Safety and warning information ......................... 4

Installation Possibilities ...................................... 5

Stand alone appliance .............................................. 5

Stand alone appliance with dividing wall .............. 5

Individual appliance at the end of the kitchen ..... 5

Installing the appliance ....................................... 6

Installation location .................................................... 6

Climatic classes ......................................................... 6

Stable installation ...................................................... 6

Installation niche ........................................................ 6

Neighbouring kitchen furniture ................................ 6

Floor ............................................................................. 6

Aligning the appliance .............................................. 6

Electrical connection ........................................... 7

Water connection ................................................. 7

Dimensions of the installation niche ................. 8

Required accessories and tools ......................... 9

Supplied accessories ............................................... 9

Optional accessories ................................................ 9

Other required accessories

from specialist outlets ............................................... 9

Miscellaneous ............................................................ 9

Tools ............................................................................ 9

Installation instructions ...................................... 10

1. Check the installation niche ............. 10

2. Removing the packaging .................. 10

3. Transport of the appliance ................ 10

4. Installation preparation ...................... 11

5. Special installation steps ................... 11

1. Attaching the anti-tilt brackets

to the wall ............................................. 12

2. Attaching alternative anti-tilt device .... 12

3. Attaching the edge protectors ......... 13

4. Attaching the fastening sheet

(lateral)................................................... 14

1. Pushing the appliance into

the installation niche ........................... 14

2. Aligning the appliance

in the niche ........................................... 15

3. Attaching the appliance

to the niche ceiling ............................. 15

4. Fastening the appliance to the side

wall of the installation niche .............. 16

1. Attaching the toe kick panel ............. 17

2. Aligning the base cover ..................... 17

3. Switching the appliance on

for the first time ................................... 18

4. Preparing the furniture doors ............ 18

5. Loading the appliance door .............. 18

6. Removing positioning aids ................ 18

7. Fastening the adjusting rib

to the furniture door

(refrigerator compartment) ................ 19

8. Fastening the fixing rib

to the furniture door

(refrigerator compartment) ................ 19

9. Fastening the adjusting rib

to the furniture door

(freezer compartment) ....................... 20

10. Fastening the fixing rib

to the furniture door

(freezer compartment) ....................... 21

11. Mounting the furniture door

(freezer compartment) ....................... 22

12. Mounting the furniture door

(refrigerator compartment) ................ 23

13. Screw on the lower fixing angle ....... 24

1. Attaching the covers .......................... 25

2. Tensioning the hinge springs

(refrigerator compartment) ................ 26

3. Mounting of air separator .................. 26

Special installation steps ................................... 27

Preparing the water connection ............... 27

Connecting the appliance

to the water supply ..................................... 27

Setting the door opening angle

(refrigerator compartment) ........................ 27

4

Safety and warning information

These mounting instructions are designed to help you

install your new appliance.

The manufacturer cannot be held liable for mounting

which has been improperly carried out. We recommend

that you allow a qualified specialist to set up and switch

the appliance on for the first time.

Following all information and keeping to the instructions

are preconditions for mounting and switching the

appliance on safely for the first time.

Keep the mounting instructions safe for use later on.

Before setting up and switching the appliance on for the

first time, read the mounting instructions fully and

thoroughly.

ã WARNING

These appliances are top-heavy and must be

secured to prevent the possibility of tipping forward.

Anti-tip protection is required.

Keep doors closed until the appliance is completely

installed and secured per installation instructions.

Due to the weight and size of this appliance, and to

reduce the risk of personal injury or damage to the

product – TWO PEOPLE ARE REQUIRED FOR

PROPER INSTALLATION.

This appliance must be properly grounded. See the

section on “Connecting the power”.

Use this appliance only for its intended purpose.

Immediately repair or replace electric service cords

that become frayed or damaged.

Unplug the appliance or switch off the fuse before

cleaning or making repairs.

Repairs should be made by a qualified service

technician.

ã CAUTION

Installation of this appliance requires basic

mechanical, carpentry and plumbing skills.

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is not

covered under the Appliance Warranty.

See the Owner's Manual for warranty information.

Important

Save these instructions for local inspector's use.

Observe all governing codes and ordinances.

Note to Installer – Be sure to leave these instructions

with the Consumer.

Note to Consumer – Keep these instructions with your

Owner's Manual for future reference.

General

These installation instructions are intended for use by

qualified installers. All connections for water, electrical

power and grounding must comply with local codes and

ordinances and be made by licensed personnel when

required. In the absence of a local code:

– In the U.S.A., in accordance with the National

Electric Code, ANSI/NFPA70 – latest edition/State

and Municipal codes and/or local codes.

– In Canada, in accordance with the Canadian Electric

Code C22.1 – latest edition/Provincial and

Municipal codes and/or local codes.

Definitions

ã

WARNING

This indicates that death or serious injuries may

occur as a result of not observing this warning.

ã CAUTION

This indicates that minor or moderate injuries or

damage may occur as a result of not observing

this warning.

Note:

This is used to draw the user's attention to something in

particular.

5

Installation Possibilities

Various installation possibilities are available.

These are only limited by the kitchen design.

Stand alone appliance

Stand alone appliance with dividing

wall

– When dimensioning the partition for model 2, note

the thickness of the door panels to prevent damage

if the doors are opened at the same time.

– Use the Heater Kit for Side-by-Side Installation

if the gap between the appliances is less than

6" (160 mm).

– See the section on “Required accessories and

tools/Optional accessories”.

– Minimum thickness of the partition

5

/

8

" (16 mm).

Individual appliance at the end of the

kitchen

If one side of the appliance is visible, a side panel must

be used.

The side panel must be connected firmly to the wall, the

floor and overhead cabinet/fixtures before the appliance

is placed in the installation niche.

The dimensions of the side panel are taken from the

opposite installation niche wall. During installation

ensure that the installation niche is square and the

proper size.

6

Installing the appliance

Installation location

ã

CAUTION

The fully-load appliance is very heavy – the load

bearing capacity at least is 1200 lbs (540 kg).

The appliance should be installed in a dry, well ventilated

space.

The location should not be exposed to the direct sunlight

and should not lie next to a source of heat such as

a cooker or a radiator etc. If installation next to a source

of heat cannot be avoided, either a suitable insulating

plate should be used or you should keep to the following

minimum distances:

–

1

/

4

" (3 cm) to electric or gas cookers.

–11

13

/

16

" (30 cm) to an oil-fired or solid-fuel cooker.

The floor of the installation location must not give way;

if required, reinforce floor. To ensure that the ice maker

functions correctly, the appliance must be upright.

Climatic classes

The climate class can be found on the rating plate.

The climate class indicates within which ambient

temperatures the appliance can be operated.

Stable installation

The appliance is very heavy and has a tendency to tilt

forwards when the appliance door is opened.

The appliance must not be switched on until there

is no possibility of the appliance tilting over.

The safest method of installing the appliance in a stable

position is to use the supplied anti-tilt brackets.

If the installation cavity is adequately stable and the

appliance can be attached securely to the upper and

side walls of the cavity, it may be possible to dispense

with the anti-tilt brackets. A prerequisite for this is always

a firm connection between the cavity and back wall!

In the case of doubt, the help of architect or specialist

builder should be enlisted.

Installation niche

It is important to keep to the stated dimensions of the

installation niche with a view to trouble-free fitting, and

the subsequent appearance of the kitchen furniture

frontage.

Special care should be taken that the niche has right

angles. The side walls should not exhibit areas that stick

out, projections or unevenness.

You should determine the right angles of the installation

niche with appropriate means, e.g. by measuring

diagonally and by using a spirit level.

The side walls and the upper end of the installation niche

must be at least

5

/

8

" (16 mm) thick.

Neighbouring kitchen furniture

The new appliance is screwed down tightly using parts

of the cabinet and the upper cabinet.

Care should therefore be taken, that all upper cabinets

to which something has been fastened are securely

connected to the subsurface or wall by appropriate

means.

The thickness of the base should be a minimum

of

3

/

4

" (19 mm).

Floor

The subsurface must be level and even in order to

ensure that the appliance is securely installed and works

correctly.

The subsurface must be made from a hard, non-flexible

material.

The floor of the installation space must have the same

height as the rest of the space.

On account of the weight of a fully-laden appliance, it is

necessary to have a bearing subsurface. In the case of

doubt, the help of architect or specialist builder should

be enlisted.

Aligning the appliance

To ensure that the appliance functions correctly, it must

be set level with a spirit level.

If the appliance is not level, water may flow out of the ice

maker, ice cubes may be irregular or the doors may not

close properly.

Climatic class Permitted ambient

temperature

SN +10 °C to 32 °C

N +16 °C to 32 °C

ST +16 °C to 38 °C

T +16 °C to 43 °C

7

Electrical connection

ã WARNING

– Avoid the risk of an electric shock!

– Insert into a grounded 3-phase socket.

Never remove grounding phase. Do not use any

adapters. Do not use any extension cables.

– Non-compliance with these instructions may

result in death, fire or an electric shock.

Improper connection of the protective

conductor may result in an electric shock. If you

are in doubt whether the appliance has been

grounded properly, have the appliance tested

by a qualified electrician or service technician.

The socket must be near the appliance and also freely

accessible following installation of the appliance.

The appliance complies with protection class I.

Connect the appliance to 115 V/60 Hz alternating

current via a correctly installed socket with protective

conductor. The socket must be fused with a 10 to 16 A

fuse.

The appliance comes with a UL registered 3-wire power

cord. The appliance requires a 3-pole socket. Please

observe the following table with regard to this:

Check on the rating plate whether the indicated voltage

and current type correspond with the values of your

power supply. The location of the rating plate can be

found in the chapter entitled Customer service.

ã WARNING

Never connect the appliance to electronic energy

saver plugs. Our appliances can be used with

mains and sine-controlled inverters. Mains-

controlled inverters are used for photovoltaic

systems which are connected directly to the

national grid. Sine-controlled inverters must be

used for isolated applications (e.g. on ships or in

mountain lodges) which are not connected

directly to the national grid.

Water connection

ã Warning:

Connect the appliance to a cold water pipe only.

The water may be connected only by a competent fitter

according to the local regulations of the appropriate

water supply company.

A cold water connection is necessary for operating the

automatic ice maker. The water pressure must be

between 25 and 120 p.s.i. (1,72 and 8,25 bar).

The installation must correspond to the local plumbing

regulations.

A separate shut-off valve should be installed in the cold-

water inflow. The shut-off valve should not be located

behind the appliance. It is recommended that you mount

the shut-off valve directly next to the appliance or at

another place which is easily accessible. When installing

the water connection, pay attention to the permissible

installation area for the water mains.

For connection to the drinking water mains use only

water pipes which are suitable for drinking water.

Observe national regulations and the connection

conditions of the local water supply companies.

When installing the water connection, observe the

permitted installation areas for the pipe. For the

permitted installation areas and dimensions see

“Dimensions of the installation niche”.

The maximum outside diameter of the water mains

(without connecting pieces) is

3

/

8

" (9.5 mm).

Appliance Maximum

simultaneous load

Fridge-Freezer combination

36" (90.3 cm)

6.0 amps

8

Dimensions of the installation niche

Key:

A Area for installation of the water connection

B Area for installation of the electric current

C Depth of the installation niche, depending on the

kitchen design

C = 24" (610 mm) minimum!

Important:

The lateral niche walls must be

completely even and free from

bumps. If the niche is formed as

a separate part, the side walls must

be completely even up to a depth of

at least 4" (100 mm) and free from

bumps.

9

Required accessories and tools

Supplied accessories

– Installation manual

– Operating instructions

– Installation accessories

Optional accessories

Extreme Combination Side-by-Side Heating kit

If the gap between the appliances is less than 6"

(160 mm).

Panel unification part (Metal strip)

For connection of two furniture doors (see explanation in

Section “C/4. Preparing the furniture doors”). Can be

used for standard height furniture doors without further

preliminary work.

Other required accessories from

specialist outlets

Ice maker installation kit

1

/

4

" OD copper line

For connecting appliances which require water,

e.g. for an ice maker.

Maximum outer diameter of the water pipe

(without fittings):

3

/

8

" (9.5 mm).

Miscellaneous

– Step ladder

– Trolley, wheelbarrow or sack barrow

– Hammer drill for drilling holes into the wall and floor

– Various size drills for various materials

– Wooden beam (cross section min. 3" x 4") as an

alternative tip protection, length according to the

width of the installation niche

– Various size wood screws

–Thin (max.

1

/

16

" (1.5 mm)), material suitable for

protecting the floor against damage (e.g. linoleum)

– Suitable material for covering and protecting

furniture (e.g. protective sheets)

– Adhesive tape

Note:

Before using, check whether the removed adhesive

tape leaves adhesive residue on the work surfaces!

Otherwise do not use on high-quality work surfaces.

Tools

Cordless screwdriver

T20 Torx-bit magnetic

holder

T20 Torx screwdriver

5

/

16

" (8 mm) socket

wrench

Various size drills

Open end wrench

1

/

2

"

(SW 13 mm)

Multigrip pliers

Adjustable wrench

Cutter with adjustable

blade

Metal tape measure,

folding ruler

Square

2' (60 cm) and 4' (1 ,2 m)

spirit levels

Level, min. 4' (1 ,2 m) long

10

Installation instructions

The following installation instructions describe the

installation steps for various appliance types.

Therefore the diagrams may be a general representation

of your appliance.

Particular reference is made to special installation steps

for individual appliance types.

1. Check the installation niche

CAUTION

Use the following check list for a safe and trouble

free installation.

1. Check the floor.

See section on “Installing the appliance/Floor”.

2. Check the dimensions of the installation niche, see

“Dimensions of the installation niche”.

3. Check that the installation niche is square.

4. Check location of the soc

ket.

See section on “Electrical connection” and in the

section on “Dimensions of the installation niche”.

5. Check location of the water connection

(only for appliances with ice maker).

See section on “Water connection” and in the

section on “Dimensions of the installation niche”.

6. Check attachment of the adjacent cabinet/fixtures.

All cabinet parts in the vicinity of the appliance must

be connected securely to the wall.

7. Check that adjacent cabinet/fixtures have adequate

clearance (door opening angle).

2. Removing the packaging

WARNING

Risk of personal injury and damage to the

appliance!

– The appliance could tilt ov

er when unpacking.

– The appliance could tilt over when the appliance

door is opened.

– The appliance is very heavy – the weight

(empty) is 511 lbs (230 kg).

Note:

Check appliance for damage in transit.

Do not install the appliance if it is visibly damaged.

If in doubt, contact your dealer.

To avoid floor damage:

1. Remove the packaging carton and be careful not to

damage the surface of appliance.

2. Place packaging cardboard or plywood under the

appliance.

3. Remove accessories from the outside

of the appliance.

Save adhesive tape which was used to attach

the supplied accessories to the

appliance.

It can be used subsequently for attaching an edge

protection to the installation niche walls (see section

on “A / 3. Attaching the edge protectors”).

4. Remove transportation protection devices (a) and lift

appliance off the pallet – appliance is very heavy!

5. Carefully open the appliance – risk of tipping over –

and remove accessories and installation materials

from inside the appliance. Close the door again.

Note:

Do not remove transportation safety devices which

protect the shelves and storage compartments

inside the appliance until the installation is complete,

otherwis

e the parts may be damaged.

a

11

3. Transport of the appliance

ã WARNING

Be careful, otherwise people who are helping may

be injured or the appliance may be damaged.

The appliance is very heavy.

The appliance is 83

1

/

8

" (2126 mm) tall. If the appliance

cannot be transported in an upright position,

the appliance can be transported horizontally.

Note:

Do not raise up the appliance via the side panels.

Risk of damage to the appliance!

When raising up the appliance, observe the required

minimum height at the installation location according to

the following table:

Note:

Never push the appliance dolly in from the front under

the appliance. Risk of damage to the appliance.

!

1. Transport the appliance with an aid to transport

which is suitable (sack barrow, trolley or

wheelbarrow).

2. When transporting, secure the appliance from being

tilted.

4. Installation preparation

Unpack installation materials and accessories.

To simplify installation, the packages are identified with

labels A, B, C and D corresponding with the manual

sections.

5. Special installation steps

The following symbol indicates that additional steps

need to be taken before proceeding to the next chapter.

Special installation steps are described after section D.

– Water connection see “Preparing the

water connection“ and „Connecting

the appliance to the water supply”.

– Door opening angle see “Setting the

door opening angle

(refrigerator compartment)”.

Raise up via

appliance rear

Do not raise up from

appliance side

Minimum height

86"/2185 mm

Do not raise up the

appliance via the side

panels!

12

1. Attaching the anti-tilt brackets

to the wall

ã WARNING

Risk of injury and damage!

Assure that there are no electrical wires or

plumbing in the area which the screws could

penetrate.

ã WARNING

Risk of injury! Always wear safety glasses and

other necessary protective devices or apparel

when installing or working with dowels.

Notes:

– Each appliance requires 2 anti-tilt brackets.

– The set supplied, contains fastening screws for

various subsurfaces. Select the fastening screws

corresponding to the local conditions.

– If the anti-tilt brackets, and therefore the appliance,

cannot be securely attached with the supplied

fastening screws, another suitable method must be

used to attach the appliance securely.

The anti-tilt brackets (a) must overlap the appliance by at

least 2

1

/

8

" (54 mm) to ensure that the appliance is

stable.

If the minimum overlap cannot be observed due to

structural conditions, these can be overcome by the

attachment of a suitable device, e.g. an adequately

dimensioned beam (b) behind the brackets.

The length of the plank should correspond to the width

of the installation niche!

1. Determine the fastening points of the anti-tilt

brackets.

Determine the actual dimensions according to the

section “Dimensions of the installation niche”.

2. Screw on the anti-tilt brackets tightly. Re-examine to

make sure that the screws are firmly tightened.

Important notes for fastening with dowels and screws:

– Not recommended for use in light-weight masonry

material such as cinder block.

– Not recommended for use in new concrete which

has not had time to cure.

– Do not use spiral-flute counterbores (countersinking

tool) to drill the holes.

13

2. Attaching alternative anti-tilt device

Important note:

If the anti-tilt brackets cannot be securely attached,

a wooden beam can be used above the appliance as an

alternative anti-tilt device. Care should be taken that

there is not a gap between the appliance and the

wooden beam. As far as possible, always screw the

wooden plank to the rear wall of the niche.

1. Saw the wooden beam (cross section min. 3" x 4")

to the required length. Length is equal to the width

of the installation niche!

Notes:

– If the installation niche is deeper than the

appliance, select a beam which has a larger

cross section or attach 2 beams.

– The beam must cover the appliance by at least 2"

(50.8 mm).

2. Mark the installation height (lower edge of the beam)

on the rear panel of the installation niche.

3. Select screws according to the thickness of the

wooden beam: length = min. 2.5 x beam thickness,

diameter #12 or #14.

Note:

Choose the number of screws according to the

installation niche width, thereby ensuring that the

beam can be attached securely.

4. Depending to the subsurface:

Locate wall studs in the rear of the installation niche

and accordingly transfer their location to the wooden

beam

or

fasten suitable dowel into the rear wall.

5. Predrill the wooden beam.

6. Attach the wooden beam to the rear panel of the

installation niche.

3. Attaching the edge protectors

To protect the edges of the installation niche, it is

recommended to attach edge protection made of

a suitable material.

Attach the edge protection with the adhesive tape which

was used to attach the accessories to the appliance.

4. Attaching the fastening sheet

(lateral)

Attach the fastening sheet (lateral) to the appliance.

The following are special installation

steps. Instructions are provided after

section D.

– Water connection see “Preparing the

water connection”.

14

1. Pushing the appliance into

the installation niche

ã CAUTION

Caution when pushing the appliance into the

installation niche. Do not damage the water line or

power cord.

Note:

When the floor or the appliance is not leveled in

comparison to the installation niche adjust height

adjustable wheels before you move the appliance into

the installation niche.

1. Remove the base panel.

2. Raise the height-adjustable wheels at the back

by approx.

3

/

8

" (10 mm).

3. Put the electric plug into the socket.

4. Push the water line into the guard tube (a) at the rear

of the appliance.

ã WARNING

The appliance may tilt when the water connection

line is inserted into the protective pipe (a)!

5. Prevent the power cord from becoming caught.

Tie a piece of string to the middle of the power cord

and feed forwards over the top of the appliance.

When pushing in the appliance, pull the cable

upwards. Take care not to pinch the power cord.

or

Using adhesive tape, tape the power cord to the

floor centrally behind the appliance approx.

15" (380 mm) away from the rear panel of

the installation niche.

6. Carefully push the appliance into the installation

niche.

7. Remove edge protection (if attached).

15

2. Aligning the appliance in the niche

Note:

To ensure that the appliance functions correctly, it must

be set perfectly levelled.

Depth alignment

The positioning aid on the door have been designed for

the following total thickness of door panels:

–

3

/

4

" (19 mm)

–1

1

/

2

" (38 mm)

Always take account of the possible differing thickness

of the panel fronts which are to be fitted subsequently.

1. Align the appliance with the cabinet fronts using the

positioning aid.

Place level over the positioning aid on the door.

Height alignment

Notes:

– Do not twist or jam the appliance inside the

installation niche! When adjusting the height-

adjustable feet, proceed gradually: Always alternate

between left and right, etc.

– For easier adjustment of the rear feet take the weight

off by slightly tilting the appliance forward.

– When using a wooden beam as an alternative anti-

tip mechanism, turn the appliance as far as it will go

against the wooden beam. Do not bend against the

wooden beam.

The height-adjustable feet at the front and rear can all be

adjusted from the front.

Front: with open-ended wrench

1

/

2

"

(Width across flats 13 mm)

Rear: with

5

/

16

" (8 mm) hex nut driver via flexible

shaft.

The mark (a) attached at the appliance base is used as

a standard gage for height adjustment. When adjusting

the height, align this mark at a height of 1

1

/

2

" (32 mm)

above the floor.

It is very important to comply with this dimension for the

subsequent alignment of the furniture fronts.

The height adjustment gauge (b) is used

to set this height correctly. The upper

edge of the gauge must be in alignment

with the mark on the appliance.

2. Unscrew the feet at the front of the appliance until

the mark (a) on the appliance is in alignment with the

upper edge of the height adjustment gauge (b).

3. Align the appliance vertically using the feet

at the back. Use a level!

3. Attaching the appliance to the

niche ceiling

Note:

It is essential to attach the appliance to the top of the

installation niche.

1. Screw the attachment plate lugs (top) to the

overhead furniture.

2. If there is a fairly large gap above the appliance,

fit a wooden beam above the appliance, ensuring

that the wooden beam fits the gap exactly.

3. If there is enough room on the top of the appliance,

fix the attachment plate side lugs (top) to the side of

the niche.

The following is a special installation

step. Instructions are provided after

section D.

– Water connection see “Connecting

the appliance to the water supply”.

4. Fastening the appliance to the side

wall of the installation niche

Screw on the bars of the fastening sheets (lateral)

with the cabinet parts located next to them.

4.

5.

6.

Shorten the fitting strip (a), to fill the gap.

Note: The appliance will be damaged if the fitting

strip is too long.

Press fitting strip (a) into the cover strip.

Attach the cover strip (b) to the attachment plate

(top).

16

17

1. Attaching the toe kick panel

Note:

Risk of damage to the appliance. Do not cover ventilation

openings in the base panel.

Nominal dimensions to be observed:

1. Where necessary, cut the base strip to the required

length.

2. Place base panel on the appliance (do not screw

on).

3. Take the protective film off from the adhesive pads

on the Velcro strip.

4. Put the base strip onto the base panel and push

firmly.

5. Base strip can be screwed to the base panel from

behind. There are holes in the base panel for this

purpose.

2. Aligning the base cover

1. Place base panel on the appliance (do not screw

on).

2. Measure the difference in depth A between the base

panel and the base strip of the adjacent lower

cabinets.

3. Remove the base panel again.

4. Adjust the brackets (a) to the dimensions A and

tighten.

5. Fasten the base panel.

18

3. Switching the appliance on for the

first time

To guarantee the accuracy of the following working steps

and thus the appearance of the overall kitchen front later

on, the appliance should now be operated.

1. Open the appliance door.

2. Press the POWER button.

Only for appliances with a water connection:

In order to avoid the risk of damage caused by leaking

water from damage possibly caused to the water pipe

feeding the appliance, keep the shut-off valve closed.

4. Preparing the furniture doors

Important notes:

When working on the furniture doors, care should be

taken to the following:

– Always carry out screwing jobs on the most stable

part of the furniture door. Never screw into fillings or

similar areas.

– Always selects screws with a length smaller than the

thickness of the cabinet front.

– Protect the surfaces of the furniture doors during

installation against damage.

The overall weight of the furniture door including the

handle should not exceed the following values:

– Refrigerator door 2 x 28.5 lbs (2x13 kg)

– Freezer drawer 28.5 lbs (13 kg)

Instead of one large door, two furniture doors can be

mounted next to each other in the case of appliances

with a width of 36" (91 cm). These furniture doors are

then connected using a metal strip on the rear.

This metal strip is available from your dealer as an

installation accessory. For further information see section

“Required accessories and tools”.

When attaching the metal strip to the furniture doors,

observe the maximum possible length of the screws and

the position of the drill holes. Always screw into the best

load-bearing material of the furniture door.

Note:

– Never screw into fillers, decorative strips or similar.

– If only one furniture door is to be attached to the

door of 36" wide appliance, attach the supplied

sandwich plate to the adjusting rail and lock into

position.

5. Loading the appliance door

When attaching the furniture doors it is recommended to

load the storage sections in the door with weights in

order to ensure that the when adjusting crack

dimensions turn out to be as precise as possible.

Loading recommendations:

– Refrigerator door 2 x 27 lbs (2x12 kg)

– Freezer drawer 22 lbs (10 kg)

6. Removing positioning aids

Unscrew the positioning aids from the appliance door.

Note:

The positioning aids will still be needed in the course of

mounting.

19

7. Fastening the adjusting rib to

the furniture door

(refrigerator compartment)

1. Measure distance A between the adjusting rail and

the furniture parts above.

2. Loosen the two nuts (a) and remove the adjusting rib

(b).

3. Mark this value A on the rear side of the furniture

door.

4. Determine the middle of the door and label it.

5. Rest the adjusting rib on the furniture door and align

to the markings. Mark the drill holes.

6. Pre-drill the holes.

7. Tightly screw the adjusting rib.

Note:

– Attach the adjusting rib with at least 6 screws on the

furniture door. One screw should be screwed in

under the threaded rod in each case.

– The adjusting rib has a various holes for different

furniture door design variations. Always carry out

screwing jobs on the most stable part of the furniture

door.

8. Fastening the fixing rib to

the furniture door

(refrigerator compartment)

Note:

The fixing ribs are pre-assembled for stainless steel

doors. In this case continue with the next installation step

(“C / 9. Fastening the adjusting rib to the furniture door

(freezer compartment)”).

1. Hang the furniture door on the threaded rod (a).

2. Adjust the furniture door using the threaded rod

(Torx screwdriver).

Re-examine the dimensions of the crack

continuously. To do this, use the assembly

gauge (b).

3. Transfer the position of the fastening screws on the

outer edge of the appliance door to the furniture

door and mark.

20

4. Remove furniture door.

5. On both lengths of the furniture door, draw a parallel

with the help of the positioning aid.

6. Lengthen the markings to the parallels using an

angle of contact.

7. Apply the fixing ribs (b) and mark out the holes.

8. Pre-drill the holes.

9. Screw on the fixing ribs (b).

10. Hang the furniture door on the threaded rods.

9. Fastening the adjusting rib to

the furniture door

(freezer compartment)

1. Measure distance A between the adjusting ribs and

the bottom edge of the refrigerator compartment

door.

2. Loosen the two nuts (a) and remove the adjusting rib

(b).

3. Mark this value A on the rear side of the furniture

door.

4. Determine the middle of the door and label it.

5. Rest the adjusting rib on the furniture door and align

to the markings. Mark the drill holes.

6. Pre-drill the holes.

7. Tightly screw the adjusting rib.

La page charge ...

Gaggenau Deals RY492701 Guide d'installation

Ce manuel convient également à

Gaggenau Deals RY492701 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents