GE ZBD9900R00II Guide d'installation

Marque: GE

Modèle: ZBD9900R00II

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Installation Instructions

Built-In Dishwasher

Ifyou have questions, call 800.GE.CARES1800.432.2737)or visit our Website at: GEAppliances.com.

In Canada, please call 1.800.561.3344or visit www.geappliances.ca

BEFOREYOU BEGIN

Readthese instructions completely and

carefully.

M PORTANT - Observeallgoverningcodesand

ordinances.

. Note to Installer - Be sure to leave these instructions for the

consumer's and local inspector's use.

. Note to Consumer - Keep these instructions with your

Owner's Manual for future reference.

. Skill Level - Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GEAppliance Warranty. Seewarranty information.

. Completion Time - 1 to 2;Hours. New installations require

more time than replacement installations.

IM PORTANT - The dishwasherMUST be installed

to allow for future removal from the enclosure if service is

required.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories - Seethe Owner's Manual for available

custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONSand WARNINGSshown

throughout these instructions. While performing

installations described in this booklet, gloves, safety glasses

or goggles should be worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

31-30264 09/23/10 GE

Installation Preparation

TOOLS YOU WILL NEED:

CI Phillips No. 2 screwdriver

CI Flat blade screwdriver

CI Torx screwdriver sizeT 20 Ph

screwdriver

CI Adjustable wrench

CI Open-ended wrench (1/2" [!2 mm] or 5/8" [!6 mm])

CI Measuring tape

CI Safety glasses

CI Flashlight

CI Bucket to catch water when flushing the line Open-ended wrench

CI Gloves

CI Level

For New Installations Only:

cI Tubing cutter

CI Drill and appropriate bits

CI Hole saw set

Flashlight

Gloves

_ --__ Level

Flat blade _ Tar× screw-_%

screwdriver driver size T 20

Adjustable

Wrench _

Safety Glasses

Hole Saw Set

Bucket

Measuring Tape

MATERIALS

CI Minimum 3/8" ODcopper tubing of sufficient length for your

installation

CI Shut-off valve and fittings for water supply line

Installation Preparation

DISHWASHER CAVITY MEASUREMENTS

® O

90°

2 _/.j/,

50-i05mm

Cable Hole

1-1/2" Max DIA.

QQmm DIA.

W : 610 mm

* Actual width of Dishwasher allows for

installation in a 23-5/8" wide cutout.

If optional Stainless Steel door panel

(ZXSS9900)is used,the cutout MUSTbe

24".

Make sure the edges of the cable

hole are even to avoid damage to

the drain and supply hoses and the

electric cable.

NOTE: A 24" cutout may require additional

trim work for the inside of the cutout for a

finished appearance.

Dishwasher door shown

without custom panel or

panel kit

34-1/4to36-1/8"

_ 870-920mm

** 28-3/8" to 3!-!/2"

72!-800mm

3/4" thick

19 mm

CUSTOM PANEL

** Height must be 28-3/8" iVllN.- 31-1/2"

MAX.to accommodate different toe kick

heights.

*** Custom panel must have 1/8" min.

clearance on each side for proper fit in

cabinet cutout.

Installation Preparation Technical Data

U.S. Metric

Height (Adjustable) 33-3/4" - 35-3/4" 857 to 908 mm

Width 23-3/8" 600 mm

Depth (Includes high 22-7/8"* 581 mm

loop)

Depth W/Door Open 49-3/4" 1266 mm

*Does not include the depth of a custom or optional door.

Electricity 120V,60Hz, 15 amp

Water pressure: 4.2-140 psi,

0.03-!.0 HPa,

0.3-10 Bar

Heating element: 1200 watt

Max loading 1300 watt

23-3/8" ),_

600 mrn

_=,,=,=,=,=,=,=_

Front

¢o

49-3/4"

1266 rnrn

22=7/8"

581 rnrn

[12"

50 mm

'-'b

85 mm _ 238 mm _

2=3/4"

70 rnrn

Installation Custom Panel

4" TOE KICK INSTALLATIONS

4" toe kick installations are possible using the supplied toe kick

or a custom built toe kick. Custom door panel height can be up

to 31-1/2" max. to align with adjacent cabinets.

6" TOE KICK INSTALLATIONS

6" toe kick installations are possible using a custom toe kick

only. Custom door panel height can be reduced to a min.

height of 28-3/8" to align with adjacent cabinets.

Installation Custom Panel

Custom Door Panel Dimensions

Your new Monogram dishwasher can be installed with a fully

integrated, buyer supplied custom door panel or Hongram

accessory panel that extends from the toe kick to the counter

top. The unit comes with everything needed to make installing

the door panel easy.

The custom panel should be a minimum of 3/4" (!9mm) thick.

Items provided with the unit

Two 3/8" screws (B)for temporarily hanging the panel.

Six 1-3/4" screws (D)for mounting the custom wooden panel

to the dishwasher.

Custom Panel Dimensions

Up to 15 Ibs, with unit

wtnt'"eg": 15-19 Ibs. Order 1X

WD01X10445

19-23 Ibs. Order 2X

WD01X10445

For dimensional information see pages 3 and 4.

INSTALLING THE CUSTOM PANEL

OR MONOGRAM ACCESSORY

PANEL

A custom door panel should be installed before the unit is

mounted to the cabinet.

Refer to the illustration at the right for instruction references.

1. Fit the handle (A)onto the panel according to the manu-

facturer's instructions. (NOTE:A handle should be used rather

than a knob, because a knob does not provide enough grip.)

IMPORTANT!The custom panel must not IJ

obstruct the fan exhaust vent; otherwise,

moisture from the vent could eventually

damage the cabinet and create drying

problems. Ea

2.The two short screws (B)go into the back

of the panel 15-7/16" (392 mm) from the upper edge of the

panel and 10-7/8" (266 mm) from the center of the panel.

Insert the short screws into the panel, leaving 1/8" (3 mm) of

space between the screw head and the panel.

3. Hook the panel screws (B)into the keyholes (C)on the dish-

washer door.

4. Slidethe panel to the left until it is centered in the opening

and secure the screws.

5. Open the door and use the six screws (D)supplied to secure

the panel to the door.

6. Exhaust vent can be adjusted by loosening vent screws on

the side of the door and moving the exhaust vent up or down.

Note: If vent is pulled downward too far it will seperate from

the exhaust conduit and must be reattached.

NOTE:If the door panel weighs more than !5 pounds, you

may need to order the heavy-duty door springs (Order Kit #

WD01X10445).

Max panel width cannot exceed cutout dimensions less 1/8"

(2.Smm)reveal on each side.

ADJUSTING THE DOOR SPRINGS

Before you push the dishwasher into the cabinet opening, test

the door to make sure it stays in place at any angle. If it tends

to fall down, pull out the machine and adjust the tension of the

door springs on the sides of the machine by moving them one

hole farther back or by twisting the spring to make it shorter.

PREPARING THE DISHWASHER FOR INSTALLATION

At this point the styrofoam, plastic wrap, and the wood pallet

(base)should be removed from the dishwasher. Now isan

excellent time to inspect for any shipping damage. Should you

find any damage, you should report it to your dealer or builder

immediately.

Be sure to remove the toe kick and toe kick insulation (only on

certain models) from the top of the dishwasher.

SLIDES FOR LEGS

The unit comes with white plastic slides for ........

the legs to protect the kitchen floor from being ........ _._

damaged when you slide the unit into place. _The slides simply snap onto the bottom of the

legs.

Protective slides for legs simply snap onto the

bottom of the legs.

ADJUSTING THE DOOR SPRINGS

Before you install the unit into the cabinet, open the door

to make sure it stays open at any .-

angle. If it tends to full down or

snap shut, pull out the machine and

tension the door springs on the sides

of the machine by moving them

one hole further back or by twisting

the spring to make it shorter. The

accessory door panel or custom

wood panel must be installed on FI

dishwashers to properly adjust tension on the door springs. If

that doesn't resolve the problem, you may need to purchase

the heavy-duty door springs (part number WD01X10/4/45).

NOTE:

If the door pond weighs more than !5 pounds, you may need

to order the heavy-duty door springs. (Seepage 5.)

CORNER INSTALLATION

If the dishwasher is installed in a corner, there must be o mini-

mum clearance of 2" (50 mm) from the side wall so the door

can open.

2" clearance

WATER SUPPLY

A WARNING:

Plumbing connections must comply with applicable sanitary, safety and plumbing codes in your area.

The machine can be connected to either a hot or cold water supply. If a cold water supply is used, the washing times will be

longer but the performance will not be affected.

The dishwasher comes with a 6-foot PEXwater supply line that has a 3/8" NPTfemale connection.

After determining where the water supply line will enter under the sink, drill a 1-1/2" access hole and run the line to the approxi-

mate inlet valve location shown in the fgure below. Thewater line inlet valve ison the right rear of the machine.

For service convenience, a shut-off valve (not supplied) should be installed in the supply line in an easily accessible location, such

as, beneath the sink.

It is important that the water supply line and the shut-off valve have a sumcient flow volume. At last 3 gallons (12 liters) per

minute must be able to pass through the line.The water pressure should be 4.2-140 psi.

ADVERTENCIA:

Las conexiones de plomer[a deben cumplir con los cbdigos sanitarios, de seguridad y de plomer[a vigentes en su _rea.

La m_quina puede conectarse al suministro de agua caliente o de agua frfa. Sise utiliza el suministro de agua if[a, los tlempos

de lavado ser_n m_s prolongados pero el desempe_o no sever_ afectado.

El lavavajillas viene con una I[nea de suministro de agua de polietileno reticulado de 6 pies que cuenta con una conexibn hem-

bra NPTde 3/8".

Despu_s de establecer el lugar en donde secolocar_ laI[nea de suministro de agua debajo del fregadero, perfore un orificio de

acceso de !-!/2" y distribuya la I[nea hasta la ubicacibn aproximada de la v_lvula de ingreso indicada en la imagen de abajo. La

vdlvula de ingreso de la I[nea de agua se encuentra en la parte trasera derecha de la m_quina.

Para mayor comodidad cuando se realiza una reparacibn, debe instalarse una v_lvula de cierre (no provista) en la I[nea de sum-

inistro en una ubicacibn f_cilmente accesible, coma par ejemplo, debajo del fregadero.

Resulta importante que la I[nea de suministro de agua y la v_lvula de cierre tengan un volumen de flujo suficiente. Par Io menos

3 galones (12 litros) par minuto deben poder pasar a travbs de la I[nea. La presibn del agua debe set de 4.2-!40 psi.

EASYINSTALL CONNECTIONS

PEXtubing with 3/8" compression fitting

PEXtubing has u 95-year spec life. FitsAmeri-

can dishwasher water supply valves. Be sure to

install the O-Ring which is attached to the PE×

tubing in a plastic bag.

Drain hose boot

Ready to be cut to desired drain

connection. Only one clamp

required.

Electrical cord

!20 volts, !5 amp cord is supplied with the

dishwasher.

A WARNING:

Do not use an extension cord for this appliance.

ADVERTENCIA:

No utilice un cable de extensi6n con este

aparato.

WARNING:

In order to prevent heat damage to the inlet valve,

all solder connections must be m(]de before the

water line is connected to the dishwasher.

DVERTENCIA:

A fin de evitGr dGSos provocGdos par el cGIor e la

vblvulo de entradG, deben reGlizGrse todGs las con-

exiones mediGnte soldGdurG antes de conectGr IG

Ifnee de aguG al IGvavajillGs.

#r -1_ _-=_---='-==,_l _:'=====-=

(1)',:

(2) ,,

_ J

1. Water supply

2. Water supply valve to dishwasher (not supplied)

NOTE:

Be sure to run the PEX tubing through the hole to sink

compartment before moving the dishwasher into position.

DRAIN CONNECTIONS

GEprovides a 7/8" (22 mm) diameter corrugated drain hose

which isconnected to the back of the unit to form a high loop.

If additional drain hose is needed, please purchase a drain

hose extension kit with a 7/8" (22mm) copper tube.

NOTE:

Do not use any fittings anywhere in the drainline that are less

than 7/8" (22mm) ID.

The access hole for the drain line should be 1-5/8" (41 mm)- 2"

(50mm) max.

The end of the drain line is 1/2"

(12 mm), but it is adjustable

to 7/8%3/4%5/8" (22mm, 19

mm, and 16 mm). If the drain

connection islarger than 1/2" (12 mm), you can easily cut the

drain line to fit the connection.

The illustrations to the right show three ways to connect the

drain supply line.

THE HiGH LOOP

The high loop is necessary for proper draining.

Therefore, the dishwasher has the drain hose

attached to the drain pump and fastened to

the top back of the unit, as illustrated. This

gives the drain hose an automatic high loop,

which isnecessary for proper draining. The drain hose is

fastened at the best high loop height.

To eliminate potential drain problems, simply leave this

hose in place.

DO NOT REMOVE THE HIGH LOOP!

IMPORTANT THINGS TO REMEMBER:

I_ Failure to provide the proper drain connection height

(minimum of 20" (508 mm) above the bottom of the

dishwasher base) or a 20" (508 mm) high loop will result in

improper drainage, which will damage the machine.

I_ No part of the drain hose should be higher than 35" (889

mm) from the bottom of the dishwasher.

I_ The drain hose can be extended to a maximum length of 10

feet (3048 mm).Joints and jointed tubes, if any, must have a

minimum 5/8" (16 mm)ID.

I_ If the drain line is going to be connected to a waste

disposer, be sure to remove the knockout or plug from the

fitting on the disposer before connecting the drain line.

I_Do not usefittings smaller than 5/8" (16 mm); otherwise the

water may not drain properly.

When the installation is ready, open the supply valve and let

the pressure act for a while. Then check that all connections

are tight and there are no leaks.

THREE WAYS TO INSTALL DRAIN CONNECTIONS

A) Typical connection to sink plumbing before trap

(high loop drain).

,,'[11

B) Connection to air gap then to the trap.

C)Connection to waste disposer with air gap.

i'_Ji

.:,.- = --

NOTE:

Don't forget to remove the knockout or plug from the disposer

fitting.

CONNECTING THE WATER SUPPLY

In order to prevent heat damage to the inlet valve, all solder

connections must be made before the water supply line is

connected.

Flush the water supply line prior to connecting it to the water

fill tube.

The unit has a float switch in the base pan to protect against

flooding. If the inlet valve connection is not seated properly,

water may leak into the base pan and activate the float

switch.

It is important that the water supply line and the shut-off valve

have a sumcient flow volume. At last 3 gallons (12 liters) per

minute must be able to pass through the line.The water pres-

sure should be 4.2-140 psi.

(1)I',

(1)Water supply

(2)Water supply valve (not supplied)

NOTE'.

Be sure to run the PEXtubing through the hole to sink

compartment before moving the dishwasher into position.

TESTING FOR LEAKS

1.Turn on the water supply and check for leaks.

2.Turn the power on at breaker/fuse box and test the

dishwasher operation by running a Rinsecycle. (Thisshould

take about four minutes.)

3.Turn off the electrical power and check for leaks under the

dishwasher and sink.

4. Make sure that no kinks have developed in the drain lines.

If there are no leaks and the dishwasher seems to be working

properly, continue with the installation.

ELECTRICAL CONNECTIONS

WARNING:

Before working on wiring for any electrical appliance, be sure

the electrical power has been turned off at the breaker/fuse

box.

, ADVERTENCIA:

Antes de comenzar a trabajar con el cableado de cualquier

aparato el6ctrico, asegOrese de haber desconectado la en-

erg[a desde el interruptor/caja de fusibles.

WARNING:

Disconnect electrical power supply and place a tag at the dis-

connect switch indicating that you are working on the circuit.

,tkADVERTENCIA:

Desconecte el suministro de energ[a el6ctrica y coloque una

etiqueta en el interruptor de desconexi6n indicando que usted

se encuentra trabajando en el circuito.

WARNING:

Electrical and grounding connections must comply with the

applicable portions of the national electrical code and/or other

local electrical codes.

, ADVERTENCIA:

Las conexiones el6ctricas y a tierra deben cumplir con las

partes aplicables del c6digo el6ctrico nacional y/u otros c6di-

gas el6ctricos locales.

The dishwasher comes with an electrical cord for 120 volts, 15

amp supplied. This cord should be plugged into the 120 volt

outlet under the sink.

If the cord is not long enough, or if a hard-wire installation is

needed, follow instructions on page 10).

GROUNDING INSTRUCTIONS

This unit must be grounded to operate properly. It must be

connected to a grounded metal, permanent wiring system,

or an equipment-grounding conductor must be run with the

circuit conductors and connected to the equipment-grounding

terminal or lead of the appliance.

Damage to the dishwasher could occur if it is not properly

grounded.

Electrical Requirements

. This appliance must be supplied with Z20V,60Hz.,and

connected to an individual properly grounded branch circuit

protected by a 15- or 20-ampere circuit breaker or time-

delay fuse.

. Wiring must be 2 wire with ground and rated for 75°C

(176°F).

. If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

. Do not modify the plug provided with this appliance, if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician. 9

ELECTRICAL CONNECTIONS (CANT)

Grounding Instructions-Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of

least resistance for electric current. This appliance

is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet

that is installed and grounded in accordance with all

local codes and ordinances.

,& WARNING:

Make sure the water supply line, drain line and

branch circuit wiring do not touch any exposed ter-

minals of dishwasher wiring.

AADVERTENCIA:

Verifique que la linea de suministro de agua, linea

de drenuje y cableudo del circuito derivudo no

toquen ningunu terminal expuestu del cubleudo del

luvuvujillus.

The improper connection of the equipment

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service representative if you

are in doubt that the appliance is properly

grounded.

La conexi6n incorrecta del conductor de

conexi6n a tierra del equipo puede resultar

en choque ei_ctrico. Consulte con un

electricista calificado o representante

de servicio si tiene dudas de la conexi6n

a tierra del aparato.

The power-supply receptacle for the dishwasher is

to be installed in a cabinet or on a wall adjacent to

the undercounter space in which the dishwasher is

to be install.

,& WARNING:

Do not use an extension cord for this appliance.

ADVERTENCIA:

No utilice un cable de extensi6n con este aparato.

/I..

- i

NOTE:

Access holes should be !-!/2" max (38.! mm max) in diameter

wlfl_ no sT_arpe_Iges.

If the cord is not long enough, or if a hard-wire installation

is needed, follow the steps below to complete the electrical

connection.

WARNING:

Before starting this procedure, be sure the power is

turned off at the breaker/fuse box.

1. Connect supply cable with a UL-listed strain relief bushing (if

nonmetallic cable isto be used).

2. Connect branch circuit white

lead to N lead on filter.

3. Connect branch circuit

black

lead to L lead on filter.

/4.Connect ground wire

to ground connection

screw on the bottom.

If the edges of the opening is wood it must be

smooth and rounded. If the edges of the opening

is metal it must be covered by an edge protector

provided for this purpose by the manufacturer. Be

careful when installing or removing the dishwasher,

to reduce the likelihood of damage to the power-

supply cord.

AADVERTENCIA:

Antes de comenzar este procedimiento, aseg0rese de haber

apagado la energ[a el6ctrica desde el interruptor/caja de

fusibles.

1. Conecte el cable de suministro con un casquillo de alivio de

tensi6n aprobado par UL(sino seva a utilizar un cable no

met61ico).

2. Conecte el cable blanco de circuito derivado al cable Ndel

filtro.

3. Conecte el cable negro de circuito derivado al cable L del

filtro.

/4.Conecte el cable a tierra al tornillo de conexi6n a tierra en la

parte inferior.

NOTE:

When doing a hard-wire installation, you must remove the

supplied power cord.

FASTENING THE DISHWASHER TO THE CABINET

NOTE:

If the door panel weighs more than !5 pounds, you may need

to order the heavy-duty door springs. (Seepage 5.)

It's necessary to fasten the dishwasher to the cabinet so

it won't tilt when the door isopened or if something heavy

is placed on the door. Use only the stainless steel screws

provided with the machine.

1. Use option A for mounting to underside

of counter-top. Useoption Bfor mount-

ing to cabinet side when counter-top isa

hard surface such as granite.

2. Cover the screw heads with the plastic plugs provided with

the machine.

3.When the machine is properly attached, check that the feet

are tight against the floor and that the machine islevel.

NOTE:

Be sure to use white spacers to keep from over-tightening the

mounting screws.

lit "1

MOVING THE MACHINE INTO PLACE

,tkWARNING:

Hake sure you put the protective slides on the legs

to prevent damaging the floor when you slide the

unit into place (see page 9).

1. Position the machine in front of the cabinet opening.

2. Hake the height adjustment while the dishwasher is in front

of the opening.

3. Pull out the drain hose to ensure there are no sharp bends.

4. Start to feed water and drain lines and electric cord (if nec-

essary) into the access hole in the cabinet.

5. Gently slide the unit into the dishwasher opening. As you do

this, feed the drain line and inlet hose into the access hole

in the side of the cabinet.

,tkADVERTENCIA:

Aseg0rese de colocar los deslizadores protectores en las

patas para evitar duflos ul piso cuundo deslice lu unidud en

su lugar (ver p6gina 9).

1. Coloque la m6quina frente u lu aberturu del gabinete.

2. Realice el ujuste de altura mientrus el luvuvajillus se en-

cuentra frente a la ubertura.

3.Tire de la manguera de drenaje para verificur que no haya

torceduras.

/4.Comience a colocar las lineas de agua y de drenaje y el

cable el6ctrico (sifuera necesario) dentro del orificio de ac-

ceso del gabinete.

5. Suavemente deslice la unidad dentro de la abertura del

lavavajillas. Hientras Io hace, coloque la linea de drenaje y

la manguera de entrada dentro del orificio de acceso en el

lado del gabinete.

Asyou slide the unit into place, feed the drain line and inlet

hose into the access hole in the side of the cabinet.

WARNING:

Be careful of sharp edges.

DVERTENCIA:

Tenga cuidado con los bordes afitados.

LEVEL DISHWASHER

IMPORTANT Dishwasher must be levelfor proper

dish rack operation, wash performance and door operation.

The dishwasher must be leveled left to right and front to back.

This assures the dish racks will not roll in or out on their own,

circulation water will flow to the pump inlet, and the door will

close without hitting the side of the tub.

. Remove the lower dish rack and place a level on the door and

lower rack track.

. Adjust the level of the dishwasher by individually turning the

four legs on the bottom of the dishwasher.

. The dishwasher isproperly leveled when the level indicator is

centered left to right and front to back. Also, the dishwasher

door should close without hitting the side of the tub.

. Replace the lower rack.

Tip: Prevent unnecessary service charges. Verify dishwasher

is leveled.

Pull the dish racks half way out. They should stay put. Open

and close the door. Thedoor should fit in the tub opening

without hitting the side of the tub. If the racks roll on their own,

or the door hits the side of tub, re-level the dishwasher.

1. Loosen the mounting screws on the dishwasher's

two front steel feet using a 5/8 inch (16mm) open-

ended wrench. Screw the mounting screws down

as close to the floor as possible.

2. Adjust the height of the dishwasher by turning

the front steel feet with your hands. Leave enough

space to adjust them later.

.................... i f .....................

kJ'

......... /:

LEVEL DISHWASHER (CONT}

3. Screw in the back foot completely by turning the

adjustment screw at the front counterclockwise.

Use a flat-bladed or a 1/4 inch nut driver.

4. Push the plastic feet into place on all three steel

feet (included in document bag).

NOTE:

Do not attach the plastic feet if the installation space

is of minimum height.

5. Push the dishwasher into the cavity. At the same

time, pull the electric cable and drainage and supply

hoses through the cable hole.

LEVEL DISHWASHER ICONT}

6. Lift the dishwasher (] little at the front and turn

the front feet to lower them.

7. Check that there is o 1/8 inch (3mm) space be-

tween the top of the dishwasher door and the

underside of the counter.

Do not ottoch the mounting screws. This will be

done later.

1/8"

3mm

8. Adjust the back foot by turning the adjustment

screw at the front clockwise.

LEVEL DISHWASHER (CONT)

9. Place the spirit level on the dishwasher door to

check that the machine is level and adjust if nec-

essary. The door must be fully closed!

NOTE:

The dishwasher must be level!

An unlevel machine can affect the amount of water

taken in, the door can be difficult to close, and the

baskets difficult to place securely.

I I

INSTALLING THE TOE KICK

SETTING THE TOE KICK DEPTH

1. Pressthe grey catches towards each other to release the

toe kick brackets.

2. Pull out the toe kick brackets as far as the installation re-

quires to provide the proper toe kick depth.

3. Once the toe kick brackets are at the appropriate depth,

press the grey catches away from each other to lock the

toe kick brackets in place.

4.The back side of the toe kick has hooks that will hang the

toe kick on the toe kick brackets. Lift the toe kick up and let

the hooks slide onto the brackets as you lower the toe kick

to the floor.

INSTALLATION CHECK LIST

Appliance Installation Checklist

• Remove packaging and check for cosmetic damages.

• Remove the information packets from inside the dishwasher.

• Attach any accessories as required by the installation. Fill strips, wooden door

panels, accessory door panels...

• Attach the drain line using the largest section of the disposer boot allowable.

Leave the high loop in place.

• Attach the PEX fill hose. Don't forget to use the O-ring.

• Plug the dishwasher into the wall.

• Turn on the water and check the fill line connections for leaks.

• Slide the unit into the cabinet and level the machine front to rear, and left to

right.

• Mount the unit to the cabinet.

• Turn the power to the unit on and start a cycle. Make sure there are no drain

leaks.

• Show the customer their warranty card, and help them locate the model and se-

rial number on the unit.

• Leave all user books for consumer.

Instructions d'instailation

Lave-vaisse e encastr

Pourtoute question, appelez le 800.GE.CARES(800.432.2737) or consultez notre site internet" GEAp-

pliances.com.

AuCanada, appelez le 1.800.561.3344ou consultez le site internet www.geappliances.ca

AVANT DE COMMENCER

LISEZCESINSTRUCTIONSENTII_REMENTET

ATTENTIVEMENT.

M PORTANT - Respecteztouslescodeset

reglementsenvigueur.

. Remarque pourl'installateur- Assurez-vousde remettre

ces instructions a I'utilisateur et a I'inspecteur local.

Remarque pour I'Utilisateur- Conservez ces instructions

avec votre notice d'utilisation pour toute r6f@ence future.

Niveau de competence - L'installation de cet appareil

demande des connaissances de base en m6canique, en

61ectricit_ et en plomberie. L'installateur est responsable de

I'installation correcte de I'appareil. La panne de I'appareil

due (3une mauvaise installation n'est pas couverte par

la garantie GEElectrom_nagers. Veuillez consultez les

informations sur la garantie.

D_lai d'ex_cution - 1 a 3 heures. Lespremieres installations

demandent plus de temps que les installations de

remplacement.

IM PORTANT - Lelave-vaisselleDOIT@treinstall6

de mani@e a permettre le retrait ult@ieur de I'enceinte afin de

permettre toute intervention.

Sivous recevez un lave-vaisselle endommag@, contactez

imm6diatement votre vendeur ou votre installateur.

Accessoires en option - Consultez le Manuel d'Utilisation pour

les ensembles de panneaux sur mesure.

POURVOTRESECURITE

Lisez et respectez tous les AVERTISSEMENTSet MBES EN

GARDEdorm,s dans cette notice. II est recommand_ de

porter des gants et des lunettes de s_curit_ ou des lunettes

_tanches lors de Pinstallation de cet appareil.

LIRE ATTENTIVEMENT.

CONSERVEZ CES INSTRUCTIONS

31-30264 09/23/10 GE

Preparation pour I'installation

OUTILLAGE NI_CESSAIRE •

CI Tournevis cruciforme No. 2

CI Tournevis 6 t_te plate

CI Tournevis Torx T20

CI CI_6 molette

CI CI6anglaise (!/2po [12 mm] ou 5/8po [16 mm])

CI Ruban 6 mesurer

CI Lunettes de s6curit6

CI Torche

CI Seau pour collecter I'eau Iors de la vidange du tuyau

CI Gants

CI Niveau

Pour les premieres installations uniquement"

CI Coupe-tube

CI Perceuse et forets appropri6s

CI Sciecylindrique _-_

CI_ anglaise

-___._ Nivea u

Tourne_e'_ Tournevis Tor-'_

plate taille T 20

Torche

CI6 6 molette

Lunettes de s_curit_

Ruban 6 mesurer

Seau forets

Gants

MATERIAU×

C! Tube en cuivre de diam_tre externe minimum de 3/8 poet

d'une Iongueur suffisante pour votre installation

C! Robinet de sectionnement et accessoires pour le tube

d'alimentation d'eau

Preparation pour I'installafion

MESURE DE L'ENCEINTE DU LAVE-VAISSELLE

90°

2-4po

50 -!05 mm

Ouverture pour le

cablel-1/2po DIA.

maxDIA 44 mm

• W_6}Omn_ ..

* La largeur r@elledu lave-vaisselle......... ......perme_-,__,, _ u t

I'installation dans une ouverture de 23-5/8

po. Si le panneau en acier inox en option

(ZXSS9900)est utilis6, rouverture doit @tre

de 24 po.

Assurez-vous que les bords de

I'ouverture pour le cable soient bien

lissespour 6viter tout dommage aux

tuyaux d'alimentation et d'6vacuation

ainsi qu'au cable d'alimentation.

REMARQUE : Une ouverture de 24 po de-

mande des travaux suppl_mentaires sur

I'int_rieur de I'ouverture pour un aspect

fini.

La porte du lave-vaisselle

est montr6e sans panneau

sur mesure ou sans pan-

neau en kit.

34-!/4po 6 36-

E !/8po

oo I70-920 mm

::0

sApo

d'6paisseur19

*** Le panneau sur mesure doit avoir un

d@gagementde 1/8 po min de chaque

c6t6 pour une bonne installation dans

I'enceinte.

PANNEAU SUR MESURE

** La hauteur doit _tre de 28-3/8 po IVllN

- et de 31 V2po MAXpour s'adapter aux

diff@entes hauteurs de plinthe.

Pr pa ration Donn_es techniques

Hauteur (ragluble) 857 to 908 mm

Lurgeur 600 mm

Profondeur (Inclut le 581 mm

tuyuu suraleva)

Profondeur uvec 16 1266 mm

porte ouverte

pour I'installation

U.S. Metric

33-3/4po - 35-

3/4po

23-3/8po

22-7/8po*

49-3/4"

*N'inclut pus lu profondeur d'un porte sur mesure ou en option.

Electricit6 120V,60Hz, 15 amp

Pression 4.2-140 psi,

d'ulimentution : 0.03-1.0 MPG,

0.3-10 Bar

El#ment chuuf- 1200 watt

runt :

Charge max 1300 watt

23-3/8po _1600 mm

r-r3

Avant o

,ED

Lr3

C)_

_c_

.°T

-.1- L!h

49-3/4po

1266 mm

22-7/8po

m 581 mm

sur#lev i

Cat#

]-i 2po -

50 mm

3-1/4p

85 mm

Installation d'un panneau sur mesure

INSTALLATIONS D'UNE PUNTHE DE 4 PO

Les installations de plinthe de 4po sont possibles en utilisant la plinthe

fournie ou une plinthe sur mesure. La hauteur des panneaux de porte sur

mesure peut allerjusqu'5:31-1/2 po max. pour _tre align# avec les meubles

de cuisine adjacents.

INSTALLATIONS D'UNE PLINTHE DE 6 PO

Les installations de plinthe de 6po sont possibles en utilisant uniquement

une plinthe sur mesure. La hauteur des panneaux de porte sur mesure peut

allerjusqu'a 28-3/8 po max. pour _tre align6 avec les meubles de cuisine

adjacents.

2-3/4po

70 mm

La page charge ...

GE ZBD9900R00II Guide d'installation

Marque: GE

Modèle: ZBD9900R00II

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE ZBD9900R00II Installation guide

GE ZBD9900R00II Guide d'installation

GE ZBD9900R00II Guide d'installation

dans d''autres langues

Documents connexes

Autres documents