TOOLS YOU WILL NEED
1
MATERIALS YOU MAY NEED
229C4053P520-2
31-10537-2 05-03 JR
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•
IMPORTANT
— Save these
instructions for local inspector’s use.
•
IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING — This appliance must
be properly grounded.
•
IMPORTANT
— Leak testing of the
appliance shall be conducted according to
the manufacturer’s instructions.
• Proper installation is the responsibility
of the installer and product failure due to
improper installation is NOT covered under
warranty.
IN THE COMMONWEALTH OF
MASSACHUSETTS:
• This product must be installed by a
licensed plumber or gas fitter.
• When using ball-type gas shut-off valves,
they shall be the T-handle type.
• A flexible gas connector, when used, must
not exceed 3 feet.
PARTS INCLUDED
2 Hold
Down Brackets
Shut Off Valve
Pipe Fittings
CSA-Approved Flexible Gas Line
3/8″ Min. ID, 1/2″ NPT Connection,
3-foot Maximum Length (Massachusetts Only)
Joint Sealant
Saber Saw
Pencil
Safety Glasses
1/8″ Drill Bit & Electric
or Hand Drill
Ruler or Straightedge
Foam Tape
2 Screws
Phillips Head
Screwdriver
Pipe Wrench
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com
In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca
Installation
30″ Sealed Gas Cooktop
Instructions JGP328, JGP932, JGP933
2
Installation Instructions
FOR YOUR SAFETY:
WARNING — If the information
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing
property damage, personal injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance!
WHAT TO DO IF YOU
SMELL GAS:
• Do not try to light any appliance. Do not
touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
IMPORTANT SAFETY INSTRUCTIONS
This cooktop has been design certified by
UNDERWRITERS LABORATORIES and CSA
International. You’ll find safety precautions in
your Owner’s Manual. Read them carefully.
• Installation of this cooktop must conform
with local codes or in the absence of local
codes with the National Fuel Gas Code,
ANSI Z223.1–Latest edition.
• Be sure your cooktop is installed properly
by a qualified installer or service technician.
• To eliminate reaching over surface burners,
cabinet storage above burner should be
avoided.
• Do not install the unit near an outside door
or where a draft may affect its use.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the
proper voltage and frequency and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on the rating plate.
We recommend you have the electrical wiring
and hookup of your cooktop connected by a
qualified electrician. After installation, have
the electrician show you where your main
cooktop disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your cooktop according to governing
codes could result in a hazardous condition.
If there are no codes, your cooktop must be
wired and fused to meet the requirements
of the National Electrical Code, ANSI/NFPA
No. 70—Latest edition. You can get a copy
by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
In Canada your cooktop must be wired
and fused to meet the requirements of the
Canadian Electrical Code.
Be sure the installation of this product
in a mobile home conforms with the
Manufactured Home Construction and
Safety Standard, Title 24 CFR, Part 3280.
If this standard does not apply, you must
follow the standard for Manufactured Home
Installations, ANSI A225.1 and Manufactured
Home Installations, Sites and Communities
and ANSI/NFPA 501A or with local codes.
You can get a copy of the Federal Standard
by Writing:
Office of Mobile Home Standards
HUD Building
451 7th Street, S.W.
Washington, D.C. 24010
3
Installation Instructions
When preparing cooktop opening,
make sure the inside of the cabinet and
the cooktop do not interfere with each
other. (See section on preparing the
opening.)
Remove packaging materials
and literature package from the
cooktop before beginning installation.
B
A
PRE-INSTALLATION CHECKLIST
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and
Care, Installations, etc. in a safe place for
future reference.
Make sure you have all the tools and
materials you need before starting the
installation of the cooktop.
Your home must provide the adequate
electrical service needed to safely and
properly use your cooktop. (Refer to
section on electrical requirements.)
When installing your cooktop in your
home, make sure all local codes and
ordinances are followed exactly as
stated.
Make sure the wall coverings,
countertop and cabinets around the
cooktop can withstand heat (up to
200°F) generated by the cooktop.
G
F
E
D
C
O
N
H
O
T
Literature Package
Styrofoam
Packaging
Cooktop
4
Installation Instructions
PREPARING THE OPENING
MAINTAIN THE FOLLOWING
MINIMUM CLEARANCE
DIMENSIONS
1
3 3/4 MIN.
OVERALL COOKTOP
DIMENSIONS
2
CUTOUT DIMENSIONS OF
COUNTERTOP
To ensure accuracy, it is best to make
a template when cutting the opening
in the counter.
3
RECOMMENDED GAS SUPPLY
LOCATION FROM BACKWALL
4
MAKE SURE WALL
COVERINGS, COUNTERTOP
AND CABINETS AROUND
COOKTOP CAN WITHSTAND
HEAT (UP TO 200°F)
GENERATED BY COOKTOP
5
13″ MAX. Depth of unprotected
overhead cabinets
6″ MIN. clearance from
cutout to side wall on
the right of the unit
18″ MIN. height
from countertop
to nearest cabinet
on either side of
unit
3-3/4″ MIN. clearance
from cutout to side wall
on the left of the unit
Cooktop
19-5/8” width cut
14-1/4″
28-1/2”
length
of cut
2-1/4” Min. Between
cutout and the wall
behind the cooktop
28-1/4″
30″
21″
3″
19-3/8″
30″ MIN. clearance from
countertop to unprotected
overhead surface
2-1/2” Min. from
front edge of
cutout and front
edge of countertop
1” Min. From Backwall
13-1/4″
From
Cutout
Center Line
Recommended
gas supply
location
Wall covering,
cabinets and
countertop
must withstand
heat up to
200°F
5
Installation Instructions
INSTALLING THE COOKTOP UNIT
LOCATE ELECTRICAL OUTLET
AND GAS SHUT-OFF VALVE
BENEATH CABINET
Install a manual shut-off valve in the gas line
in an easily accessible location outside the
cooktop. Be sure you know how and where to
shut off the gas supply to the cooktop. Install
the electrical outlet 12″ below the countertop.
1
NEVER REUSE
OLD CONNECTORS
WHEN INSTALLING
THIS UNIT.
PROTECT SURFACE OF
COOKTOP
Place a towel or tablecloth onto the
countertop. Lay the cooktop upside down
onto the protected surface.
2
ATTACH FOAM TAPE
(glass maintop models only)
Apply the foam tape around the outer edge
of the glass. Do not overlap the foam strips.
3
LOCATE MOUNTING PARTS
Remove the hold down brackets from the
literature package.
4
ATTACH BRACKETS TO
COOKTOP
Remove the screw from the side of the
cooktop and screw the hold-down bracket
to the side of the cooktop unit. Repeat for
opposite side of cooktop.
5
INSERT COOKTOP INTO
CUTOUT
Insert the cooktop centered into the cutout
opening. Make sure the front edge of the
countertop is parallel to the cooktop. Make
final check that all required clearances are met.
Once the unit is in place, screw the hold-
down bracket into the cabinet sides to secure
the unit into place.
6
Shut Off
Valve
Electrical
Outlet 12″
Below
Countertop
Bottom of cooktop
Cloth under Cooktop
Cooktop
Pre-drilled
hole
Foam Tapes
Bottom of
Cooktop
Cooktop
Glass
Foam Tapes
Bottom of Cooktop
Cooktop Glass
6
Installation Instructions
INSTALLING THE COOKTOP
PROVIDE ADEQUATE GAS
SUPPLY
This cooktop is designed to operate on
natural gas at 4″ of water column pressure.
It is shipped from the factory set for natural
gas. The convertible pressure regulator
supplied with the unit must be connected in
series with the manifold of the cooktop and
must remain in series with the supply line
regardless of whether natural or L.P. gas is
being used. FOR PROPER OPERATION,
THE MAXIMUM INLET PRESSURE TO THE
REGULATOR MUST BE NO MORE THAN
14″ OF WATER COLUMN PRESSURE. For
checking the regulator, the inlet pressure
must be at least 1″ (or 3.4 KPA) greater than
the regulator output setting. If the regulator is
set for 4″ of water column pressure, the inlet
pressure must be at least 5″. If the regulator
is set for 10″, the inlet pressure must be at
least 11″. The gas supply line to the cooktop
should be 1/2″ or 3/4″ pipe.
1
INSTALL THE REGULATOR
NEVER REUSE OLD CONNECTORS WHEN
INSTALLING THIS COOKTOP.
WARNING: Never reuse old
flexible connectors. The use of old flexible
connectors can cause gas leaks and personal
injury. Always use new flexible connectors
when installing a gas appliance.
To reduce the likelihood of gas leaks, apply
teflon tape or a thread compound approved
for use with LP or Natural gases to all
threaded connections.
2
Screw a section of pipe
onto each end of the
pressure regulator.
INSTALL REGULATOR ONTO
BURNER BOX BOTTOM
Screw the
regulator and
pipe connection
into the burner
box bottom.
Make sure the
top of the
regulator is
facing towards
the cabinet front,
easily accessible
through the
cabinet doors.
3
COMPLETE THE CONNECTION
WITH A COUPLING
Install a coupling
between the
regulator and the
shut off valve to
complete the
connection.
4
Pressure
Regulator
Pressure
Regulator
Shut-Off
Valve
Electrical
Outlet 12″
Below
Countertop
Pressure
Regulator
Shut Off
Valve
Coupling
Electrical
Outlet 12″
Below
Countertop
7
Installation Instructions
INSTALLATION OVER
BUILT-IN OVEN
See built-in oven installation for complete
installation instructions.
6
CHECK FOR LEAKS
Check for leaks. After connecting the
cooktop to gas, check system for leaks with
a manometer. If a manometer is not available,
turn the gas supply on to the cooktop and
use a liquid leak detector at all joints and
connections to check for leaks. Tighten all
connections if necessary to prevent gas
leakage in the cooktop or supply line.
Check alignment of valves after connecting
the cooktop to the gas supply to be sure
the manifold pipe has not been moved.
A misalignment could cause the valve knob
stem to rub on the control panel, resulting
in a gas leak at the valve.
DO NOT USE OPEN FLAME TO CHECK
FOR LEAKS!
Disconnect this cooktop and its individual
shutoff valve from the gas supply piping
system during any pressure testing of
that system at test pressures greater than
1/2″ psig.
Isolate the cooktop from the gas supply
piping system by closing its individual shutoff
valve during any pressure testing of the gas
supply system at test pressures equal to or
less than 1/2″ psig.
5
5” To Center of
2” Dia. Hole From
Countertop
2″ Dia. Hole
(20-7/8″ from front
of Countertop to
Hole Center)
Cabinet Sides
90° Street El
8
Installation Instructions
EXTENSION CORDS
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an extension cord.
However, if you still elect to use an extension
cord, it is absolutely necessary that it be a
UL listed 3-wire grounding type appliance
extension cord and that the current carrying
rating of the cord in amperes be equivalent
to or greater than the branch circuit rating.
Such extension cords are obtainable through
your local appliance dealer.
IMPORTANT:
(Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
1
ELECTRICAL SUPPLY AND
OUTLET
An adequate electrical supply and outlet must
be used to operate the electrical parts of your
cooktop.
The power cord of this appliance is
equipped with a 3-prong (grounding)
plug which must be used with a properly
grounded 3-hole outlet with a standard
120 Volt, 60 cycle AC household current.
If you do not have a 3-hole grounded
outlet, have a qualified electrician
change your old one.
A grounding adaptor will be needed
to convert the old one until the outlet
can be replaced. This method is only
temporary, and a qualified electrician
should test it to be sure it meets
requirements.
C
B
A
2
Installation Instructions
INSTALLATION—ELECTRICAL CONNECTIONS
TWO-PRONG WALL
RECEPTACLE
Where a standard 2-prong wall receptacle is
encountered, it is the personal responsibility
and obligation of the customer to have it
replaced with a properly grounded 3-prong
wall receptacle.
Do not under any circumstances cut or
remove grounding prong from the cooktop
cord. Failure to provide proper polarization
may create a hazardous condition.
3
N
L
Insure proper
ground and
firm connection
before use
9
Installation Instructions
USAGE SITUATIONS WHERE
APPLIANCE POWER CORD
WILL BE DISCONNECTED
INFREQUENTLY
For 15 amp circuit only. Do not use an adaptor
on a 20 amp circuit. Where local codes permit,
a TEMPORARY CONNECTION may be made to
a properly grounded 2-prong wall receptacle by
the use of a UL-listed adaptor available at most
hardware stores. The larger slot in the adaptor
must be aligned with the large slot in the wall
receptacle to provide proper polarity in the
connection of the power cord.
CAUTION:
Attaching the adaptor ground
terminal to the wall receptacle cover screw
does not ground the appliance unless the
screw is metal, and not insulated, and the wall
receptacle is grounded through the house
wiring. The customer should have the circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.
When disconnecting the power cord from the
adaptor, always hold the adaptor with one
hand. If this is not done, the adaptor ground
terminal is very likely to break with repeated
use. Should this happen, DO NOT USE the
appliance until a proper ground has again been
established.
Usage situation where appliance power cord
will be disconnected frequently.
Do not use an adaptor plug in these situations
because disconnection of the power cord
places undue strain on the adaptor and leads to
eventual failure of the adaptor ground terminal.
The customer should have the 2-prong
receptacle replaced with a 3-prong (grounding)
receptacle by a qualified electrician before
using the appliance.
4
Ensure proper ground and
firm connection before use
Align large
prongs/slots
Temporary Method
(Adaptor plugs not permitted in Canada)
10
Installation Instructions
ASSEMBLING THE COOKTOP
BURNERS
The electrode of the spark igniter is exposed.
Be careful not to push any cooktop controls
while the top of the burner is removed.
Do not remove the top or touch the electrode
of any burner while another burner is turned
on. Electrical shock might result.
FOR PORCELAIN COOKTOPS
Place the burner head on the burner
base so that the pins match up with the
slots on the base.
Position the burner cap on the burner
head.
Place the burner grate over the burner
assembly on the porcelain units. The
bottoms of the burner grates have feet
that fit into corresponding indentations
in the cooktop.
C
B
A
1
COOKTOP BURNERS
FOR GLASS CERAMIC COOKTOPS
Place the burner head on the burner
base so that the pins match up with
the slots on the base.
Position the burner cap on the burner
head.
Place the burner grate over the burner
assembly on the ceramic units. The
grate fits over the raised area on the
burner head.
C
B
A
Burner Cap
Burner Head
Spark Igniter
Burner Box
Bottom
Burner
Base
Burner
Grate
Spark
Igniter
Burner Cap
Burner Head
Spark Igniter
Burner Box
Bottom
Maintop
Front Trim
Burner
Base
Burner
Grate
Spark
Igniter
11
Installation Instructions
CHECK IGNITERS
Operation of the electric igniters should be
checked after the cooktop and supply line
have been carefully checked for leaks and the
cooktop has been connected to the electrical
power.
Push and turn a burner valve to the LITE
position.
• The burner valve should light when
gas is available to the burner
• Once the burner lights, it should be
turned out of the LITE position.
Try each valve separately until all
burners have been checked.
B
A
2
BURNER IGNITION
Cooktop Spark Ignition—When you turn
the cooktop knob to LITE, the spark igniter
makes a series of electric sparks (ticking
sounds) which light the burner.
During a power failure, the burners will
not light automatically. In an emergency,
a cooktop burner may be lit with a match
by following the steps below.
WARNING: Lighting gas burners
with a match is dangerous. You should
match light the cooktop burners only in
an emergency.
Light a match and hold the flame near
the burner you want to light. Wooden
matches work best.
Push in and turn the control knob slowly.
Be sure you are turning the correct knob
for the burner you are lighting.
NOTE: If the burner does not light within five
seconds, turn the knob off and wait one minute
before trying again.
B
A
3
THE BURNER FLAMES
Turn each burner on. Flames should be blue
in color with no trace of yellow. The burner
flames should not flutter or blow away from
the burner. The inner cone of the flame
should be between 1/2″ and 3/4″ long.
WARNING:
If you attempt to
measure the inner cone of the flame, please
use caution. Burns could result.
4
Burners should be checked frequently
Cooktop Burner
1/2″
to
3/4″
12
Installation Instructions
OPERATION CHECKLIST
Double check to make sure everything in
this guide has been completed. Rechecking
steps will ensure safe use of the cooktop.
Make sure all controls are left in the
OFF position.
Make sure the flow of combustion
and ventilation air to the cooktop is
unobstructed.
The serial plate for your cooktop is
located on the bottom of the burner
box. In addition to the model and serial
numbers, it tells you the ratings of the
burners and the type of fuel and pressure
the cooktop was adjusted for when it
left the factory.
When ordering parts, always include the
serial number, model number and a code
letter to ensure proper replacement parts.
Recheck Steps:
Double check to make sure everything
in this guide has been completed.
Rechecking steps will ensure safe
use of the cooktop.
F
E
D
C
B
A
13
Installation Instructions
MAKING THE LP CONVERSION
SAFETY INFORMATION YOU
SHOULD KNOW
The pressure regulator and burner orifices
are set for natural gas. To use Propane Gas,
the regulator and burner orifices must be
converted. The LP orifice spuds for the
cooktop burners can be located within a
bracket attached to the pressure regulator
of this unit.
CAUTION: The cooktop, as shipped
from the factory, is set for use with natural
gas. If you wish to use your cooktop with
Liquefied Petroleum (Propane) gas, you must
first replace the orifices and convert the
pressure regulator.
WARNING:
This conversion
must be performed by a qualified installer
or gas supplier in accordance with the
manufacturer’s instructions and all codes
and requirements of the authority having
jurisdiction. Failure to follow instructions
could result in serious injury or property
damage. The qualified agency performing
this work assumes responsibility for the
conversion.
CAUTION:
The following adjustments
must be made before turning on the burner.
Failure to do so could result in serious injury.
Be sure pressure regulator has been
converted as described in Step 2.
1
ADJUST YOUR COOKTOP FOR
USE WITH LP GAS
Disconnect all electrical power, at the
main circuit breaker or fuse box.
Shut off the gas supply to the cooktop
by closing the manual shut-off valve.
Adjust the pressure regulator, by the
following instructions:
• Unscrew the cap.
• Place your thumb against the flat side
of the spring retainer and press down
to remove the retainer.
• Carefully look at the spring retainer to
locate the NAT or LP position.
• Turn the spring retainer over so that LP
is showing on the bottom.
• Snap the retainer back into position.
C
B
A
2
DOWN
FOR OFF
NAT
LP
LP
NAT
LP
NAT
NAT
LP
Gasket
Cap
Spring
Retainer
L.P./Propane
Position
NAT.
Position
Pressure Regulator
14
Installation Instructions
MAKING THE LP CONVERSION (CONT.)
CHANGE THE COOKTOP
BURNER ORIFICES
Remove the top grates, burner caps,
burner heads and burner bases.
Remove the
electrodes from the
burner base. Using a
No. 15 “Torx” head
driver bit, remove the
screws holding the
burner base in
position.
Using a 7mm or
9/32″ nut driver,
remove the top
burner orifices.
These may be
accessed through the
hole in the cooktop.
NOTE: The orifices have
a spring loaded retaining
ring around the hex head
to hold the orifice in
the nut driver during
installation and removal.
A slight amount of force is required to push
the nut driver down over the ring.
Locate the LP/Propane orifices shipped
inside the literature package. They
will have a digit number and the letter
“L” on the side. (Important: Save the
orifices removed from the appliance
for future use.)
Each orifice will show a series of
engraved marks, (I, II, III or X), located
on the top.
These marks denote the precise location of
each orifice to the cooktop burner.
D
C
B
A
3
Units with 1500 BTU/HR burner on right front.
(See rating plate on bottom of appliance.)
Units with 9100 BTU/HR burner on right front.
(See rating plate on bottom of appliance.)
Install the LP/Propane orifices in
their precise locations as noted in the
illustrations above.
Return the natural orifices to the
bracket and reattach the bracket and
the instruction sheet to the pressure
regulator using the screw previously
removed.
Replace the burner bases, heads,
caps and top grates. (NOTE: When
re-attaching the burner bases to glass
top units, tighten screws to a maximum
of 10 in.-lbs torque.)
G
F
E
I II III X
III
II
I
X
II
II
I
II
Remove
This
Assembly
Orifice Spud Located
Thru This Opening
Retainer
Ring
15
Installation Instructions
ADJUST THE BURNERS,
LOW FLAMES
Turn all burners full on and check the
flames. They should be blue in color with
no trace of yellow. Foreign particles in
the gas line may cause an orange flame
at first, but this will soon disappear.
Turn the control valve to low position
while observing the flame.
To make adjustment, remove the control
knobs. Insert a screwdriver through
access hole in valve switch. Engage
adjustment screw in valve.
• If the flames were too small or
fluttered, open the valve more than
the original setting.
• If the flames blew away from the
burner, close the valve more than
the original setting.
Make the adjustment by slowly turning
the screw until flame appearance is
correct.
D
C
B
A
4
Adjust the low flame setting using the valve
bypass screw as follows:
Low-setting adjustments must be made
with two other burners in operation on a
medium setting. This prevents the low
flame from being set too low resulting in
the flame being extinguished when other
burners are turned on.
Testing Flame Stability:
Test 1 – Turn the knob from “HI” to
“LOW” quickly. If the “LOW”
flame goes out, increase the
flame size and test again.
Test 2 – With the burner on the “LOW”
setting, open and close the
cabinet door under the cooktop.
If the flame is extinguished by
the air currents created by the
door movement, increase the
flame height and test again.
Flame Recheck:
After the adjustment is made, turn all burners
off. Ignite each burner individually. Observe
the flame at the “HI” position. Rotate the
valve to the “LO” position and be sure that
the flame size decreases as the valve is
rotated counterclockwise.
TO CONVERT THE COOKTOP BACK TO
NATURAL GAS, REVERSE THE STEPS
UNDER MAKING THE LP CONVERSION.
Once the conversion is complete and
checked ok, fill out the LP sticker and
include your name, organization and date
conversion was made. Apply the sticker
near the cooktop gas inlet opening to alert
others in the future that this appliance has
been converted to LP gas. If converting back
to natural gas from LP, please remove the
sticker so others know the appliance is set
to use natural gas.
F
E
16
Notes
Printed in the United States
1
OUTILS DONT VOUS AUREZ
BESOINS
MATÉRIAUX DONT VOUS POUVEZ
AVOIR BESOIN
229C4053P520-2
31-10537-2 05-03 JR
AVANT DE COMMENCER
Avant de commencer, lisez attentivement la
totalité de ces instructions.
•
IMPORTANT — Conservez ces
instructions pour votre inspecteur local.
•
IMPORTANT — Respectez toutes
les ordonnances et les codes locaux.
• Note à l’installateur – Assurez-vous de
laissez ces instructions au consommateur.
• Note au consommateur – Conservez ces
instructions pour référence future.
• La garantie ne couvre aucune panne due à
une mauvaise installation.
AVERTISSEMENT —
Cet appareil coit être bien mis à la terre.
•
IMPORTANT — Vous devez
vérifier que cet appareil n’a pas de fuite
conformément aux instructions du
fabricant.
• L’installateur est responsable d’une bonne
installation et la garantie ne couvre aucune
panne due à une mauvaise installation.
PIÈCES COMPRISES
2 Supports de
fixation
Robinet
d’alimentation de gaz
Raccords de tuyaux
Raccord flexible de gaz approuvé par l’ACNOR
DI min 3/8’’, Jonction NPT 1/2
Agent de scellement
de tuyau
Scie sauteuse
Crayon
Lunettes de sécurité
Perceuse à main ou
électrique et foret de 1/8″
Règle ordinaire ou de
vérification
Bandes de mousse
(Pour les modèles à
surface en verre
seulement)
2 vis
Tournevis Phillips
Clé à tuyau
Questions? Appelez le Centre de réponse 1.800.361.3400 ou visitez notre site
Web à l’adresse : www.electromenagersge.ca
Instructions
Table de cuisson scellée
d’installation
au gaz de 76 cm (30″)
JGP328, JGP932, JGP933
2
Instructions d’Installation
POUR VOTRE SÉCURITÉ
AVERTISSEMENT —
Si vous ne suivez pas exactement les
instructions de ce manuel, vous risquez
d’occasionner un incendie, une explosion
ou une fuite de gaz, qui peuvent provoquer
des dommages matériels, des blessures
corporelles ou la mort.
Ne conservez pas ou n'utilisez jamais
d'essence ou d'autres liquides ou vapeurs
inflammables à proximité de cet appareil
ou de tout autre appareil ménager!
CI QUE VOUS DEVEZ
FAIRE SI VOUSSENTEZ
LE GAZ:
• N’essayez jamais d’allumer un appareil
électroménager. Ne touchez à aucun
commutateur d’électricité, n’utilisez jamais
un téléphone dans votre bâtiment.
• Appelez immédiatement votre fournisseur
de gaz à l’aide du téléphone d’un voisin.
Suivez les instructions de votre fournisseur
de gaz.
• Si vous ne pouvez pas entrer en
communication avec votre fournisseur
de gaz, appelez les pompiers.
L’installation et service de votre table de
cuisson doivent être faites par un installateur
qualifié, un technicien de service ou votre
fournisseur de gaz.
INSTRUCTIONS IMPORTANTES DE SÉCURITÉ
La conception de votre table de cuisson a été
approuvé par l’ACNOR International. Vous
trouverez des précautions ô prendre en
matière de sécurité dans votre Guide
d’utilisation et de soins. Lisez-les
attentivement.
• L’installation de votre table de cuisson
doit se conformer aux codes locaux ou, en
l’absence de codes locaux, au National Fuel
Gas Code, ANSI Z223.1 Dernière édition.
• Assurez-vous que votre table de cuisson
soit bien installée par un installateur qualifié
ou un technicien de service.
• Pour éliminer tout mouvement corporel
au dessus des brûleurs de votre table de
cuisson, évitez de placer des armoires de
cuisine au dessus des brûleurs.
• N’installez jamais votre appareil près d’une
porte d’entrée ou à un emplacement où un
courant d’air peut gêner son usage.
3
Instructions d’Installation
BESOINS D’ÉLECTRICITÉ
Cet appareil ménager doit être livré avec le
bon voltage et la bonne fréquence et branché
à son propre circuit de dérivation bien mis à
la terre, protégé par un disjoncteur ou un
fusible qui ont l’ampérage noté sur la plaque
de cotation
Nous vous recommandons de faire brancher
le câblage électrique et la fiche de votre
cuisinière par un électricien qualifié. Après
l’installation, demandez à l’électricien de vous
montrer l’emplacement de votre coupe-circuit
principal.
Demandez à votre entreprise de services
publics les codes électriques en vigueur
dans votre région. En ne câblant pas votre
cuisinière conformément aux codes en
vigueur, vous provoquez une situation
dangereuse. En l’absence de codes, vous
devez câbler et isoler votre cuisinière
conformément aux exigences du Canadian
Electrical Code.
4
Instructions d’Installation
Pour préparer l’ouverture de la surface
de cuisson, vous devez vous assurer
que l’intérieur de l’armoire ne touche
pas la table de cuisson (consultez la
section sur la préparation de
l’ouverture).
Retirez les matériaux d’emballage et
la trousse de documentation de votre
table de cuisson avant de commencer
à l’installer.
B
A
LISTE DE VÉRIFICATION AVANT INSTALLATION
Enlevez les instructions d’installation
de la trousse de documentation et
lisez-les soigneusement avant de
commencer.
Assurez-vous de bien ranger toute la
documentation, l’utillisation et less
soins, les installation, etc. dans un
endroit sûr pour référence future.
Assurez-vous d’avoir tous les outils et
tous les matéraux nécessaires avant de
commencer à installer votre table de
cuisson.
Votre maison doit être alimentée en
courant électrique adéquat pour vous
permettre de bien utiliser en toute
sécuité votre table de cuisson.
(Consultez la section sur les besoins
d’électricité.)
Pour installer votre table de cuisson
dans votre maison, assurez-vous de
vous conformer scrupuleusement à
tous les codes et à toutes les
ordonnances locales.
Assurez-vous que les revêtements
de mur, le comptoir et les armoires
autour de la table de cuisson puissent
supporter la chaleur [pouvant atteindre
93°C (200°F)] produite par la table de
cuisson.
G
F
E
D
C
O
N
H
O
T
Trousse de
documentation
Emballage en
mousse de
polystyrène
Table de Cuisson
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
dans d''autres langues
- English: GE JGP328BECBB Installation guide
Documents connexes
-
GE JGP932CECCC Guide d'installation
-
-
-
-
-
-
GE Profile JGP330SEKSS Manuel utilisateur
-
GE Profile Series JGP970SEKSS Guide d'installation
-
-