Installation
Instructions
30" SealedGasCooktop
JGP328, JGP330, JGP933,
JGP940, JGP945
Ouestions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
I
IN THE COMMONWEALTH OF
MASSACH USETTS:
• This product must be installed by a licensed
plumber or gas fitter.
• When using ball-type gas shut-off valves, they
shall be the T-handle type.
• A flexible gas connector, when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•IMPORTANT - Savetheseinstructions
forlocalinspector'suse.
•IMPORTANT - Observeallgoverning
codes and ordinances.
• Note to Installer- Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions for
future reference.
• Product failure due to improper installation is not
covered under the Warranty.
._WARNING - This appliance must be
properly grounded.
• IMPORTANT - Leak testingofthe
applianceshallbe conducted accordingto the
manufacturer'sinstructions.
• Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
-&WARN ING - Disconnectallelectrical
power atthe main circuitbreaker
orfuse box beforeinstalling.
FOR YOUR SAFETY:
_WARNING - Ifthe information
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing property
damage, personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
WHAT TO DO IF YOU SMELL
GAS:
Do not try to light any appliance. Do not touch
any electrical switch; do not use any phone in
your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
This cooktop has been design certified
by CSA International. You'll find safety precautions
in your Owner's Manual.
Read them carefully.
Installation of this cooktop must conform with
local codes or in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54-Latest edition.
Be sure your cooktop is installed properly by a
qualified installer or service technician.
To eliminate reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-i0613-5 (IO-IOGE) 1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
ELECTRICAL REOUIREMENTS
This appliance must be supplied with the proper
voltage and frequency and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as noted on the rating plate.
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician
show you where your main cooktop disconnect is
located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
cooktop according to governing codes could result
in a hazardous condition.
If there are no codes, your cooktop must be wired
and fused to meet the requirements
of the National Electrical Code, ANSI/NFPA No. 70--
Latest edition. You can get a copy
by writing:
National Fire Protection Association
Batterymarch Park
Ouincy, MA 02269
InCanada your cooktop must be wired
and fused to meet the requirements of the
Canadian Electrical Code.
Be sure the installation of this product
in a mobile home conforms with the Manufactured
Home Construction and
Safety Standard, Title 24 CFR, Part 3280.
If this standard does not apply, you must follow
the standard for Manufactured Home Installations,
ANSI A225.1 and Manufactured Home Installations,
Sites and Communities and ANSI/NFPA 501A or
with local codes.
You can get a copy of the Federal Standard by
Writing:
Office of Mobile Home Standards
HUD Building
451 7th Street, S.W.
Washington, D.C. 24010
PARTS INCLUDED
2Screws
Foam Tape
2 Hold
Down Brackets
MATERIALS YOU MAY NEED
Joint Sealant Pipe Fittings
Shut-Off Valve
CSA-Approved Flexible Gas Line
3/8" Min. ID, 1/2" NPTConnection,
3-foot Maximum Length (Massachusetts Only)
TOOLS YOU WILL NEED
FOR INSTALLATION
Pencil
Phillips-Head
Screwdriver
Saber Saw
Ruler or Straightedge
Safety Glasses
Pipe Wrench
1/8" Drill Bit & Electric or
Hand Drill
Installation Instructions
PRE-INSTALLATION CHECKLIST
_3
F_
When preparing cooktop opening, make
sure the inside of the cabinet and the
cooktop do not interfere with each other.
(See section on preparing the opening.)
Remove packaging materials, grate boxes,
regulator with literature, and literature
package from the cooktop before beginning
installation.
Package
Grate boxes
Foam_ _ _X
Pac _ _ _ El
Cool<top J
E1
r61
[]
FF1
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and Care,
Installations, etc. in a safe place for future
reference.
Make sure you have all the tools and
materials you need before starting the
installation of the cooktop.
Your home must provide the adequate
electrical service needed to safely and
properly use your cooktop. (Refer to section
on electrical requirements.)
When installing your cooktop in your home,
make sure all local codes and ordinances
are followed exactly as stated.
Make sure the wall coverings, countertop
and cabinets around the cooktop can
withstand heat (up to 200°F) generated by
the cooktop.
Installation Instructions
PREPARING THE OPENING
B3
MAINTAIN THE FOLLOWING
MINIMUM CLEARANCE
DIMENSIONS
15" MAX.Depth of unprotected
overhead cabinets _
3-3/4" MIN.clearance from __
cutout to side wall on the -I U_h
left of the unit IF _
6" IVllN.clearance from
II cutout to side wall on the
of the unit
18" MIN. height
S from countertop to
nearest cabinet on
either side of unit
NOTE: All gas cooktop models require 7/16"
free area below cooktop height to combustible
material.
ITI OVERALL COOKTOP DIMENSIONS
21" (21-1/2" Max. for
30" _ Glass Top models)
19-3/8" _
I_l CUTOUT DIMENSIONS OF
COUNTERTOP
To ensure accuracy, it is best to make
a template when cutting the opening
in the counter.
_._ 28-i/2'
length -
! _ of cut
2-1/4" Min. Between -_--
cutout and the wall
behind the cooktop
2-1/2" Min. from
front edge of cutout
and front edge of
countertop
19-5/8" width cut
14-1
RECOMMENDED GAS SUPPLY
LOCATION FROM BACKWALL
1" Min. From Backwall
Recommended _ '[
gas supply
location "_ 15-i/_'
_4 From Cutout
Center Line
F51 MAKE SURE WALL COVERINGS,
COUNTERTOP AND CABINETS
AROUND COOKTOP CAN
WITHSTAND HEAT (UP TO 200°F)
GENERATED BY COOKTOP
Wall covering,
cabinets and
countertop must l
withstand heat I
Installation Instructions
INSTALLING THE COOKTOP UNIT
B3
LOCATE ELECTRICAL OUTLET AND
GAS SHUT-OFF VALVE BENEATH
CABINET
NEVER REUSE OLD
CONNECTORS WHEN
INSTALLING THIS
UNIT.
i i
I_ s¢
shutoff :\
Valvo iElectrical
Outlet 12"
Below
Countertop
Install a manual shut-off valve in the gas line in an
easily accessible location outside the cooktop. Be
sure you know how and where to shut off the gas
supply to the cooktop. Install the electrical outlet
12" below the countertop.
[_ PROTECT SURFACE OF COOKTOP
Place a towel or tablecloth onto the
countertop. Lay the cooktop upside down onto the
protected surface.
Bottom of cooktop j
Cloth under Cooktop
[_] ATTACH FOAM TAPE
(glass maintop models only)
Apply the foam tape around the outer edge
of the glass. Do not overlap the foam strips.
Bottom of Cooktop
_. Foam Tapes
Cooktop Glass
LOCATE MOUNTING PARTS
Remove the hold down brackets from the
literature package.
_-I ATTACH BRACKETS TO COOKTOP
Remove the screw from the side of the cooktop
and screw the hold-down bracket
to the side of the cooktop unit. Repeat for opposite
side of cooktop.
Pre-drilled
Bottom of hole X _t/
Cooktop X _/
Glass
I-_ INSERT COOKTOP INTO CUTOUT
Insert the cooktop centered into the cutout
opening. Make sure the front edge of the countertop
is parallel to the cooktop. Make final check that all
required clearances are met.
Once the unit is in place, screw the
hold- down bracket into the cabinet sides
to secure the unit into place.
Installation Instructions
INSTALLATION--GAS CONNECTIONS
PROVIDE ADEQUATE
GAS SUPPLY
This cooktop is designed to operate on natural
gas at 4" of water column manifold pressure and
7" of water column (W.C.) supply pressure. It is
shipped from the factory set for natural gas. The
convertible pressure regulator supplied with the
unit must be connected in series with the manifold
of the cooktop and must remain in series with the
supply line regardless of whether natural or L.P.
gas is being used. FOR PROPEROPERATION, THE
MAXIMUM INLET PRESSURETO THE REGULATOR
MUST BE NO MORE THAN 14" OF WATER COLUMN
PRESSURE.For checking the regulator, the inlet
pressure must be at least 1" W.C.. (or 3.4 KPA)
greater than the regulator output setting. If
the regulator is set for 4" W.C. of water column
pressure, the inlet pressure must be at least 5" W.C.
If the regulator is set for 10" W.C., the inlet pressure
must be at least 11" W.C.. The gas supply line to
the cooktop should be 1/2" or 3/4" pipe.
_l INSTALL REGULATOR
NEVER REUSEOLD CONNECTORS WHEN
INSTALLING THIS COOKTOP.
.&WARNING: Never reuse old flexible
connectors. The use of old flexible connectors
can cause gas leaks and personal injury. Always
use new flexible connectors when installing a gas
appliance.
Screw a section of pipe onto
the inlet end of the pressure
regulator and install the
coupling.
Pressure _]
Regulator _L_
Coupling _
To reduce the likelihood of gas leaks, apply teflon
tape or a thread compound approved for use with
LP or Natural gases to all threaded connections.
INSTALL REGULATOR ONTO
BURNER BOX BOTTOM
Screw the regulator
onto the burner
box bottom pipe
connection. Make
sure the top of
the regulator is
facing towards the
cabinet front, easily
accessible through
the cabinet doors.
Pressure _l
Regulator'S11
Coupling _I
Shut-Off I
Valve
LI
Ii Electrical
II Outlet 12"
I Below
Countertop
COMPLETE CONNECTION WITH A
COUPLING
I
l
Pressure
Regulator
Coupling
Shut-Off _
Valve
Complete the
connection between
the regulator pipe
coupling and
the shut-off valve.
clJ
U
II Electrical
I Outlet 12"
I Below
Countertop
Installation Instructions
_-I CHECK FOR LEAKS
Before testing for leoks, moke sure oll burner knobs
(]re in the OFF position.
After connecting the cooktop to gas, check system
for leaks with (] manometer. If (] manometer is not
available, turn the gas supply on to the cooktop
and use (] liquid leak detector at (]lljoints and
connections to check for leaks.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
DO NOT USE OPEN FLAME TO CHECK FOR
LEAKS!
Disconnect the cooktop and its individual shut-off
valve from the gas supply piping system during any
pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kP(]).
Isolate the cooktop from the gas supply piping
system by closing its individual shut-off valve
during any pressure testing of the gas supply
system at test pressures equal to or less than 1/2
psig (3.5 kP(]).
INSTALLATION OVER BUILT-IN
OVEN
See built-in oven installation for complete
installation instructions.
I
t
5" To Center of
I / _ 2" Dim.Hole From
__ _ Countertop
90° Elbow _ ---
2" Dia. Hole
L_ (20 7/8" from front
I_ of Countertop to
_'_l Hole Center)
Cabinet Sides _//_KJA'\_I_,,,_
Installation Instructions
INSTALLATION--ELECTRICAL CONNECTIONS
./I,WARN ING - Disconnect oil electricol
power ot the main circuit breoker
or fuse box before instolling.
EXTENSION CORDS
Because of potential safety hazords under certoin
conditions, we strongly recommend against the
use of an extension cord. However, if you still
elect to use an extension cord, it is absolutely
necessary that it be a UL listed B-wire grounding
type applionce extension cord ond thot the
current carrying rating of the cord in amperes be
equivalent to or greoter than the branch circuit
roting. Such extension cords ore obtoinoble
through your Iocol opplionce deoler.
IMPORTANT: (Pleosereod corefully)FOR
PERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
ELECTRICAL SUPPLY AND OUTLET
An odequote electricol supply ond outlet must
be used to operote the electricol ports of your
cooktop.
The power cord of this applionce is equipped
with o 3-prong (grounding) plug which must
be used with o properly grounded 3-hole
outlet with u standard 120 Volt, 60 cycle AC
household current.
If you do not hove o 3-hole grounded outlet,
hove o quolified electricion chonge your old
one.
A grounding oduptor will be needed to convert
the old one until the outlet con be reploced.
This method is only temporary, ond a qualified
electricion should test it to be sure it meets
requirements.
Insure proper
ground ond
firm connection
before use
TWO-PRONG WALL RECEPTACLE
Where a standard 2-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to hove it replaced with
u properly grounded B-prong wall receptacle.
Do not under any circumstonces cut or remove
grounding prong from the cooktop cord. Failure
to provide proper polarization may create u
hazardous condition.
Installation Instructions
USAGE SITUATIONS WHERE
APPLIANCE POWER CORD
WILL BE DISCONNECTED
INFREQUENTLY
For 15 amp circuit only. Do not use an adaptor
on a 20 amp circuit. Where local codes permit, a
TEMPORARY CONNECTION may be made to a properly
grounded 2-prong wall receptacle by the use of a
UL-listed adaptor available at most hardware stores.
The larger slot in the adaptor must be aligned with
the large slot in the wall receptacle to provide proper
polarity in the connection of the power cord.
Ensure proper ground and firm
connection before use
Align large 1_
prongs/slots
Temporary Method
(Adaptor plugs not permitted in Canada)
A _^,|'T'|_L,
_ILI,.,/'_U/IU I_1: Attaching the adaptor ground
terminal to the wall receptacle cover screw does not
ground the appliance unless the screw is metal, and
not insulated, and the wall receptacle is grounded
through the house wiring. The customer should have
the circuit checked by a qualified electrician to make
sure the receptacle is properly grounded.
When disconnecting the power cord from the
adaptor, always hold the adaptor with one hand. If
this is not done, the adaptor ground terminal is very
likely to break with repeated use. Should this happen,
DO NOT USE the appliance until a proper ground has
again been established.
Usage situation where appliance power cord will be
disconnected frequently.
Do not use an adaptor plug in these situations
because disconnection of the power cord places
undue strain on the adaptor and leads to eventual
failure of the adaptor ground terminal. The customer
should have the 2-prong receptacle replaced with
a 3-prong (grounding) receptacle by a qualified
electrician before using the appliance.
Installation Instructions
COOKTOP BURNERS
ASSEMBLING THE COOKTOP
BURNERS
The electrode of the spark igniter is exposed. Be
careful not to push any cooktop controls while the
top of the burner is removed.
Do not remove the top or touch the electrode
of any burner while another burner is turned on.
Electrical shock might result.
O0 Replace the burner head onto the burner
bose, making sure that the head is properly
oriented over the burner bose and the
electrode. IVloke sure to place
the correct burner head on the correct burner
bose and that the burner head sits level on
the burner bose. The burner heads ore not
interchangeable.
[]8
Place the burner
cops on the burner
heads, making sure
to place the correct
burner cop on the
correct burner
head. The burner
cops ore not
interchangeable.
IVloke sure that the
burner cops ore
properly seated on
the burner heads.
Burner cop properly seated
Burner cop not properly seated
[]
Hake sure the pins in
the burner heads
match the burner
bose indentutions
and that they ore
properly seated in
them by rotating the
heuds until they ore
level.
IVlokesure the slot in
the burner head
is positioned
over the
electrode.
The burner cup
has
three to four
pins. When
replacing the
cup, make
sure none of
the pins sits
in the stmbility
chamber.
Burner cop
Burner head
_ectrode
__Burner
Pin bose
indentations
Stobilit_
chamber _
Electrode
Burnerbose
Hake sure
the hole
in the burner
head assembly is
positioned over the
electrode and that
the burner head is
fully inserted inside
the burner base. A
small gap between
the base and head is
normal.
Burner cop
Burner head
ossembl i_
Electrode Burner
bose
lO
Installation Instructions
[_ CHECK IGNITERS
Operation of the electric igniters should be checked
after the cooktop and supply line have been
carefully checked for leaks and
the cooktop has been connected to the electrical
power.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
r_ Push and turn o burner valve to the LITE
position. All spark igniters will make u series of
sparks (ticking sounds), but only the burner
turned to LITE will light.
• The burner should light when gas is
available to the burner.
• Once the burner lights, it should be turned
out of the LITE position.
r_ Try each valve separately until all burners
have been checked.
[_ THE BURNER FLAMES
Turn each burner on. Flames should be blue in color
with no trace of yellow. The burner flames should
not flutter or blow away from the burner. The flame
should be no less than 1/4" on the lowest setting
and no greater than 1-1/2" on highest setting.
A __ __
AWARNING: Ifyouattempt to measure
the flame, please use caution. Burns could result.
1/4" to _ I _ Cooktop Bumer
1-1/2"
Burners should be checked frequently
_-I BURNER IGNITION
Cooktop Spark Ignition-When you turn
the cooktop knob to LITE,the spark igniter makes u
series of electric sparks (ticking sounds) which light
the burner. During o power failure, the burners will
not light automatically. In an emergency, o cooktop
burner may be lit with o match by following the
steps below.
- WARNING: Lighting gas burners with o
match is dangerous. You should match light the
cooktop burners only in
an emergency.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
rA1 Light a match and hold the flame near the
burner you want to light. Wooden matches
work best.
rB1 Push in and turn the control knob slowly. Be
sure you are turning the correct knob for the
burner you are lighting.
NOTE: If the burner does not light within five seconds,
turn the knob off and wait one minute before trying
again.
BURNER GRATES
The four cooktop grates are designed for specific
positions. For maximum stability, these grates
should only be used in their proper position: they
should not be interchanged. For your convenience,
the undersides of the left and right grates are
marked "OUTSIDE" and "INSIDE". Hake sure that the
side marked "OUTSIDE" is on the outer edge of your
cooktop.
"OUTSIDE.... INSIDE.... OUTSIDE"
edge edges edge
11
Installation Instructions
OPERATION CHECKLIST
Hake sure all controls are left in the OFF
position. Check to be sure the cooktop is in the
UNLOCKED position (on models so equipped).
Hake sure the flow of air to and from the
cooktop is unobstructed.
The serial plate for your cooktop is located on
the bottom of the burner box. In addition to the
model and serial numbers, it tells you the ratings
of the burners and the type of fuel and pressure
the cooktop was adjusted for when it left the
factory.
@
RI
When ordering parts, always include the serial
number, model number and a code letter to
ensure proper replacement parts.
Recheck Steps:
Double check to make sure everything in this
guide has been completed. Rechecking steps
will ensure safe use of the cooktop.
12
Installation Instructions
MAKING THE LP CONVERSION
If sold outside the U.S.and Canada:
AtLW/-_KI_ I I_1 Ifyou wish to use this product
with Liquefied Petroleum (LP)gas containing greater
than 10% butane, you must purchase a butane
conversion kit. To order,
please call 1.888.664.8403 or 1.787.276.4051.
Model Butane Kit #
JGP940 WB28T10228
JGP945 WB28T10230
JGP933 WB28T10232
JGP330 WB28T10234
JGP328 WB28T10236
TOOLS YOU WILL NEED
FOR LP CONVERSION
Phillips-Head
Screwdriver
Pliers
Safety Glasses
7mm Nutdriver
No. 15 Torx-Head
Driver
Small Flat-Head
Screwdriver (4mm or
5/32" tip size,60mm
long)
Fll SAFETY INFORMATION YOU
SHOULD KNOW
The pressure regulator and burner orifices are set
for natural gas.To use LPgas,
the regulator and burner orifices must
beconverted. The LPorifice spuds for
the cooktop burners can be located in the literature
package attached to the regulator.
A,-^, |,,r,,-, L,
JLU/'_U/IUI_: The cooktop, as shipped from
the factory, is set for use with natural gas. If you
wish to use your cooktop with LP gas, you must
first replace the orifices and convert the pressure
regulator.
,A,WARN ING:This conversion
must be performed by a qualified installer
or gas supplier in accordance with the
manufacturer's instructions and all codes
and requirements of the authority having
jurisdiction. Failure to follow instructions could
result in serious injury or property damage. The
qualified agency performing this work assumes
responsibility for the conversion.
A ,-^, |'T',,_L,
JLL./-_U/IUI_: The following adjustments
must be made before turning
on the burner. Failure to do so could result in
serious injury. Be sure pressure regulator has been
converted as described in Step 2.
E1
ADJUST YOUR COOKTOP FOR USE
WITH LP GAS
Disconnect all electrical power, at the main
circuit breaker or fuse box.
Shut off the gas supply to the cooktop
by closing the manual shut-off valve.
Adjust the pressure regulator, by the following
instructions:
• Unscrew the cap.
• Place your thumb against the flat side of the
spring retainer and press down to remove
the retainer.
• Carefully look atthe spring retainer to locate
the NAT or LP position.
Gasket
Spring
Retainer
NATF_"_: L.P./Propane
Position
Poslt_
Pressure Regulator
• Turn the spring retainer over so that LP is
showing on the bottom.
• Snap the retainer back into position.
• Screw the cap back onto the regulator.
13
Installation Instructions
MAKING THE LP CONVERSION (CONT.)
E1
CHANGE COOKTOP BURNER
ORIFICES
Remove the top grotes,
burner cops, ond burner
heods.
Remove the spork
igniters from the burner
bose (if required to
occess the orifices).
Using o No. 15 "Torx"
heod driver bit, remove
the screws holding the
burner bose in position.
_[ Remove This
_ Assembly
-. :_o<.J
Orifice Spud Locoted
Through This Opening
Using o 7mm nut driver,
remove the top burner
orifices. These moy be
occessed through the
hole in the cooktop.
Burner cop
_ Burner
Spork igniter bose
18,000 BTUBurner
Ion some models)
Burner
cop
_Burner
Burner _ heod
bose
Spork igniter
CHANGE COOKTOP BURNER
ORIFICES (CONT.)
NOTE: On most burners,
the orifices hove o spring- Retoiner
Iooded retoining ring Ground Ring
the hex heud to hold the
orifice in the nut driver during
instullution ond removol. A
slight omount of force is required to push the nut
driver down over the ring.
14
Installation Instructions
CHANGE COOKTOP BURNER
ORIFICES (CONT.)
Locate the LP/Propane orifices shipped
inside the literature package. They
will have a digit number and the letter "L" on
the side. (Important: Save the orifices
removed from the appliance
for future use.)
Each orifice will show a series of engraved
marks, (I, II, III, X or none),
located on the top.
These marks denote the precise location of each
orifice to the cooktop burner.
OOOO
18,000 BTU/HR Burner (on some models)
O he 18,0OOBTU/HRburner has two orifices with
markings located inthe sides only. (Seerating
plate on bottom of appliance).
NOTE: The main orifice is located low in the center
of the burner while the simmer orifice is located
higher behind the center of the burner.
Simmer__
orifice
Main orifice
Left Rear LeftFront RightFront
Model Orifice Orifice Orifice
JGP328 II II II
JGP330 II II III
JGP933 III II X
JGP940 III III X
JGP945 III II Replace: With:
Main 206XN --) 108XL
Simmer 57N -) 34L
[]
Install the LP/Propane orifices in
their precise locutions as noted in the
illustrations above.
Return the natural gas orifices to the bracket
and reattach the bracket and the instruction
sheet to the pressure regulator using the
screw removed previously.
Replace the burner bases, heads, caps and
top grates. (NOTE: When re-attachinq the
burner bases to qlass top units, tiqhten screws
to a maximum of
10 in.-Ibs torque.)
15
Installation Instructions
MAKING THE LP CONVERSION (CONT.)
ADJUST BURNER FLAMES
Turn all burners full on and check the flames.
They should be blue in color with some yellow
tipping at the ends of the flame. Foreign
particles in the gas line may cause an orange
flame at first, but this will soon disappear.
NOTE:For the 18,000 BTU/HR burner (on some
models) the cooktop burner knob should be
turned to the setting before the lowest setting.
This will ensure that the entire burner is
operating.
r_ Turn the cooktop burner knob to the lowest
setting while observing the flame.
Adjust the low flame setting using the valve bypass
screw as follows:
Low-setting adjustments must be made with two
other burners in operation on a medium setting.
This prevents the low flame from being set too low,
resulting in the flame being extinguished when
other burners are turned on.
E1 To adjust the flame, remove the knobs. Insert
a screwdriver through the access hole in valve
switch. Engage
adjustment screw in
valve. Refer to the
illustration below that I
matches the adjustment
screw location for your
model.
• If the flames were too _//
small or fluttered, open
the valve more than
the original setting.
• If the flames blew
away from the burner,
close the valve more
than the original
setting.
burner
/only
r-_ Make the adjustment by slowly turning the
screw until flame appearance is correct.
Note: Some models may contain a silicone shield
which covers the valve switch and access hole. A
flashlight may be required to locate the access hole. To
access the valve adjusting screw, push the screwdriver
through this shield. After adjustment, reseat the
shield around the switch hub with your fingers, after
withdrawingthescrewdriver.
Reseat silicone shield
CORRECT INCORRECT
r_ Testing Flame Stability:
Test 1 - Turn the knob from "HI" to the lowest
setting quickly. If the flame goes out
at the lowest setting, increase the
flame size and test again.
Test 2 -
With the burner on the lowest setting,
open and close the cabinet door
under the cooktop. If the flame is
extinguished by the air currents
created by the door movement,
increase the flame height and test
again.
I_1 Flame Recheck:
After the adjustment is made, turn all burners off.
Ignite each burner individually. Observe the flame
at the "HI" position. Rotate the valve to the lowest
setting and be sure that the flame size decreases
as the valve is rotated counterclockwise.
TO CONVERT THE COOKTOP BACK TO NATURAL
GAS, REVERSETHE STEPSUNDER MAKING THE LP
CONVERSION.
Once the conversion is complete and checked
ok, fill out the LP sticker and include your name,
organization and date conversion was made. Apply
the sticker near the cooktop gas inlet opening to
alert others in the future that this appliance has
been converted to LP gas. If converting back to
natural gas from LP, please remove the sticker so
others know the appliance is set to use natural gas.
16
Instructions
d°installation
Table de cuisson scell
au gaz de 76 cm (30")
JGP328, JGP330, JGP933,
JGP940, JGP945
I Pl Questions? Appelez le Centre de r_ponse 1.800.561.3344 ou visitez notre site
Web 8 I'odresse ' www.electromenogersge.co
I
AVANT DE COMMENCER
Avant de commencer, lisez attentivement la totalit6
de ces instructions.
•IMPORTANT - Conservezces
instructionspourvotreinspecteurlocal
•IMPORTANT - mespecteztoutesles
ordonnances etlescodes locaux
• Note c_l'installateur- Assurez-vousde laissezces
instructionsau consommateur
• Note au consommateur - Conservez ces
instructionspour r6f6rencefuture
• Lo garantiene couvre aucune panne due
c_une mauvaise installation
-AAVERTISSEMENT -
Cet appareil doit @trebien mis (_la terre.
•IMPORTANT - vousdevez
verifierque cetappareiln'aitpas de fuite
conform6ment aux instructionsdu fabricant
• L'installateur est responsable d'une bonne
installation et la garantie ne couvre aucune
panne due _]une mauvaise installation.
-_AV ERTISSEM ENT - D6brancheztout
courant 61ectrique au niveau du disjoncteur de la
maison ou de la boTte _]fusibles avant d'installer.
POUR VOTRE SI_CURITI_
-AAVERTISSEMENT -
Si vous ne suivez pas exactement les instructions
de ce manuel, vous risquez d'occasionner un
incendie, une explosion ou une fuite de gaz, qui
peuvent provoquer des dommages mat6riels, des
blessures corporelles ou la mort.
Ne conservez pas ou n'utilisezjamais d'essence
ou d'autres liquides ou vapeurs inflammables _]
proximit6 de cet appareil ou de tout autre appareil
m6nager!
CI QUE VOUS DEVEZ FAIRE SI
VOUS SENTEZ LE GAZ :
N'essayezjamais d'allumer un appareil
61ectrom6nager. Ne touchez _]aucun
commutateur d'61ectricit6, n'utilisezjamais un
t616phone dans votre b(_timent.
Appelez imm6diatement votre fournisseur de
gaz _]I'aide du t616phone d'un voisin. Suivez les
instructions de votre fournisseur de gaz.
Si vous ne pouvez pas entrer en contact avec
votre fournisseur de gaz, appelez les pompiers.
L'installation et le service de votre table de cuisson
doivent @trefaits par un installateur qualifi6, un
technicien de service ou votre fournisseur de gaz.
31-10613-5 (lo-lo GE) 1
Instructions d'instollotion
INSTRUCTIONS IMPORTANTES DE SI CURITI
La conception de votre table de cuisson a 6t6
approuv6 par I'ACNOR International. Vous trouverez
des pr6cautions _]prendre en mati_re de s6curit6
duns votre Guide d'utilisation et de soins. Lisez-les
attentivement.
• L'installation de votre table de cuisson
doit se conformer aux codes Iocaux ou, en
I'absence de codes Iocaux, au National Fuel Gas
Code, ANSI Z223.1/NFPA 54 Derni_re 6dition.
• Assurez-vous que votre table de cuisson soit
bien install6e par un installateur qualifi6 ou un
technicien de service.
• Pour 61iminer tout mouvement corporel
au dessus des brOleurs de votre table de cuisson,
6vitez de placer des armoires de cuisine au
dessus des brOleurs.
• N'installezjamais votre appareil pros d'une porte
d'entr6e ou dans un emplacement o0 un courant
d'air peut g@ner son usage.
BESOINS D'I_LECTRICITI_
Cet appareil m6nager doit @tre livr6 avec le ban
voltage et la bonne fr6quence et branch6 _]son
propre circuit de d6rivation bien mis _]la terre,
prot6g6 par un disjoncteur ou un fusible qui ant
I'amp6rage not6 sur la plaque min6ralogique de
votre appareil.
Nous vous recommandons de faire brancher le
cablage 61ectrique et la fiche de votre cuisini_re
par un 61ectricien qualifi& Apr_s I'installation,
demandez _]1'61ectricien de vous montrer
I'emplacement de votre coupe-circuit principal.
Demandez 6 votre entreprise de services publics les
codes 61ectriques en vigueur dans votre r6gion. En
ne c0blant pas votre cuisini_re conform6ment aux
codes en vigueur, vous provoquez une situation
dangereuse. En I'absence de codes, vous devez
c0bler et isoler votre cuisini_re conform6ment aux
exigences du Canadian Electrical Code.
PII_CES COMPRISES
2 vis
Bandes de mousse (Pour
les modules 6 surface en
verre seulement)
S
2 Supports de fixation
MATI_RIAUX DONT VOUS POUVEZ
AVOIR BESOIN
Agent de scellement
de tuyau
Raccords de tuyaux
Robinet d'alimentation
de gaz
Raccord flexible de gaz approuv_ par I'ACNOR
DI min 3/8", Jonction NPT1/2
OUTILS DONT VOUS AUREZ BESOINS
Crayon
Tournevis Phillips
Scie sauteuse
R_gle ordinaire ou de
v_rification
Lunettes de s_curit_
CI_@tuyau
Perceuse _] main ou _lectrique
et foret de 1/8po
Instructions d'installation
LISTE DEVITRIFICATION AVANT INSTALLATION
Pour pr6parer I'ouverture de la surface de
cuisson, vous devez vous assurer que
I'int6rieur de I'armoire ne touche pas la table
de cuisson (consultez la section sur la
pr6paration de I'ouverture).
Enlevez les mat@iaux d'emballage, les
boTtes de grille, le r6gulateur avec sa
documentation et la documentation de
votre table de cuisson avant de commencer
6 I'installer.
_1_ Documentation
BoTtes de
grille
/
Emballage _
en mousse
"__ LI DDD I3
L / Table de /
cuisson
E1
El
Enlevez les instructions d'installation de la
trousse de documentation et lisez-les
soigneusement avant de commencer.
Assurez-vous de bien ranger toute la
documentation, le manuel d'utilisation et
d'entretien, etc. dans un endroit sOr pour
r6f6rence future.
Assurez-vous d'avoir tousles outils et tous
les mat6raux n6cessaires avant de
commencer 6 installer votre table de
cuisson.
El Votre maison doit #tre aliment6e en courant
61ectrique ad6quat pour vous permettre de
bien utiliser en toute s6curit6 votre table de
cuisson. (Consultez la section sur les besoins
d'61ectricit6.)
El Pour installer votre table de cuisson dans
votre maison, assurez-vous de vous
conformer scrupuleusement 6 tous les
codes et 6 toutes les ordonnances locales.
[]
Assurez-vous que les rev@tements de mur, le
comptoir et les armoires autour de la table
de cuisson puissent supporter la chaleur
[pouvant atteindre 93°C (200°F)] produite
par la table de cuisson.
PRI:!PARATION
Instructions d'installation
DE L°OUVERTURE
VOUS DEVEZ RESPECTER LES
DEGAGEMENTS MINIMAUX
SUIVANT
Profondeur max de 33 cm (13") des
armoires en surplomb non prot6g6es
D6gagement m_
droite de I'appareil
D6gagement min. de 15
cm (6") d6coupage au
i,r_prpdaeeiCl6t66 droite de
_I Hauteur min de
S 5 cm (18") du
comptoir
6 Farmoire la
plus proche de
chaque c6t6 de
I'appareil
REMARQUE : tous les modules de surface
6 cuisson au gaz requi_rent un d6gagement
de 1,1 cm (7/16 po) sous la hauteur de la surface
pour la mati_re combustible.
ITI DIMENSIONS DU DI_COUPAGE DE
LA TABLE DE CUISSON
49 cm (19-3/8") ...._I_........'_
DIMENSIONS TOTALES DE
LA TABLE DE CUISSON
Pour assurer lajustesse du d6coupage,
il vaut mieux faire un gabarit pour couper
I'ouverture dans le comptoir.
72,/4cm (28-1/2 po)
Iongueur du d6coupage _ Largeur du d6coupage
_._19-5/8")
Distance min de 5,7 _" _ _ .... _ ]
cm(2-1//4") _ _ II
de d6coupage au f IIl_h !'
mur derriere la table / I_r_ 4Ia
de cuisson 6,4 cm (2-1/2") Distance
min. de I'ar@teavant du
d6coupagede I'arr@teavant de
la table de cuisson
EMPLACEMENT RECOMMA.NDI_ DE
L'ALIMENTATION DE GAZ A
PARTIR DU MUR ARRII_RE
Emplacement
recommand6 de
I'alimentation
de gaz
2.5 cm (1") min. du mur arri_re
i
_._- 33.7 cm ___i
(13-i//4")Du
d6coupage
6 lalignedu
centre
ASSUREZ-VOUS QUE
LES REVr:TEMENTS MUR, LE
COMPTOIR ET LES ARMOIRES
AUTOUR DE LA TABLE DE
CUISSON PUISSENT SUPPORTER
LA CHALEUR (POUVANT
ATTEINDRE 93°C [200°F])
pouvoir supporter
une chaleru pouvant
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
dans d''autres langues
- English: GE PGP943DETBB Installation guide
Documents connexes
-
GE JGP330SEKSS Guide d'installation
-
GE Profile JGP330SEKSS Manuel utilisateur
-
-
-
-
-
-
-
GE PGP976DET4WW Guide d'installation
-