Thermador DWHD651GFP/18 Guide d'installation

Marque: Thermador

Modèle: DWHD651GFP/18

Taper: Guide d'installation

_uJ

€_

Lt_

€_

A Important Safety instructions

To avoid possible injury or property damage, OBSERVE

ALL WARNINGS AND CAUTIONS.

These instructions are intended for use by qualified

installers only. The dishwasher must be installed by a

qualified service technician or installer.

, In addition to these instructions, the dishwasher

shall be installed to meet all electrical and plumbing

codes and ordinances (both national and local).

Read these installation instructions completely and

follow them carefully, They will save you time and ef-

fort and help to ensure safety and optimum dishwasher

performance.

Inspect the Dishwasher

After unpacking the dishwasher and prior to installation,

thoroughly inspect the dishwasher for possible freight or

cosmetic damage. Report any damage immediately.

Cosmetic defects must be reported within 30 days of

installation.

NOTE: Do not discard any bags or items that come

with the original package until after the entire installation

has been completed.

IMPORTANT

, The dishwasher drain hose must be installed with

a portion of it at least 20" (508mm) off the cabinet

floor; otherwise the dishwasher may not drain prop-

erly.

This dishwasher is intended for indoor residential

use only, and should not be used in commercial

food service establishments.

NEW INSTALLATION - If the dishwasher is a new

installation, most of the work must be done before

the dishwasher is moved into place.

REPLACEMENT - If the dishwasher is replacing

another dishwasher, check the existing dishwasher

connections for compatibility with the new

dishwasher, and replace parts as necessary.

, This appliance has been found to be in compliance

with CAN/CSA-C22.2 No. 167/UL 749. It is the

responsibility of the owner and the installer to

determine if additional requirements and standards

apply in specific installations.

, Not for outdoor use.

Avoiding General Hazards

Do not use the dishwasher until it is completely

installed. When opening the door on an uninstalled

dishwasher, carefully open the door while supporting

the rear of the unit. Failure to follow this warning can

cause the dishwasher to tip over and result in serious

injury.

Before installing the "L"-shaped supplied countertop

mounting brackets (select models), decide which

method will be used to secure the dishwasher into its

opening. Once these mounting brackets are installed

on the dishwasher, removing them is difficult and will

damage the mounting brackets and the dishwasher.

in some conditions, hydrogen gas can form in a hot

water system that has not been used for weeks.

Hydrogen gas is explosive.

Before filling a dishwasher from a system that has

been off for weeks, run the water from a nearby faucet

in a well ventilated area until there is no sound or evi-

dence of gas.

Temperatures required for soldering and sweating will

damage the dishwasher's base and water inlet valve.

If plumbing lines are to be soldered or sweated, keep

the heat source at least 6 inches (152.4 mm) away

from the dishwasher's base and water inlet valve.

Make sure electrical work is properly installed. There

should be no loose electrical connections. Ensure all

electrical connections are properly made.

The customer has the responsibility of ensuring that the

dishwasher electrical installation is in compliance with

all national and local electrical codes and ordinances.

The dishwasher is designed for an electrical supply

of 120V, 60 Hz, AC, connected to a dishwasher-

dedicated, properly grounded electrical circuit with a

fuse or breaker rated for 15 amps. Electrical supply

conductors shall be a minimum #14 AWG copper only

wire rated at 75°C (167°F) or higher.

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or

lead on the appliance. Do not use extension cords.

Avoiding Plumbing/Scalding Hazards__ [_

Do not perform any work on a charged hot water line.

Serious injury could result. Only qualified plumbershould

perform plumbing work. Do not attempt any work on

the dishwasher hot water supply plumbing until you

are certain the hot water supply is shut off.

Removing any cover or pulling the dishwasher from the

cabinet can expose hot water connections, electrical

power and sharp edges or points. Handle with care.

Avoiding Electrical Shock/Fire Hazards

Do not allow the electrical and water supply lines to

touch. Separate channels are provided under the

dishwasher.

Do not work on an energized circuit. Doing so could

result in serious injury or death. Only qualified electri-

cians should perform electrical work. Do not attempt

any work on the dishwasher electric supply circuit

until you are certain the circuit is de-energized.

Do not over tighten the 90 ° elbow. Doing so may

damage the water inlet valve and cause a water leak.

Temperatures required for soldering and sweating will

damage the dishwasher's water inlet valve. If plumbing

lines are to be soldered or sweated, keep the heat

source at least 6 inches (152.4 mm) away from the

dishwasher's water inlet valve.

Check local plumbing codes for approved plumbing

procedures and accessories. All plumbing should be

done in accordance with national and local codes.

These instructions depict an installation method for

stainless steel braided hose or PEX hot water supply

lines. If using copper tubing or other material for

water supply, defer to a licensed plumber for proper

installation.

Hammer Hole Saw

F ............................. r_b)

Pipe Wrench Adjustable Wrench

Tape Measure

Slot Screwdriver

Phillips Screwdriver

1-20 Screwdriver

Wire Cutter

Wire Stripper

L©,

Level

Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1

ground, insulated copper conductors rated 75°C or higher.

Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or metal

braided dishwasher supply line.

Shut-off valve and fittings appropriate for hot water supply line

(copper tubing/compression fitting, or braided hose).

UL listed conduit connector or strain relief is required ifyou attach

the field wiring directly to the terminal block.

_ I_::i_

A Extra Tall Item Sprinkler (See Use and Care Manual)

B Toe Panel Screws

C Mounting Brackets

D Mounting Bracket Screws

E Toe Panel (2 pieces)

F Toe Panel caps

G Screw Clamp (for hose)

H Water Supply Adaptor Fitting

I Flexible Edge Protector Grommet for electrical wire

J Rubber Drain Hose Adaptor

K Toe Panel Mounting Brackets (select models only)

L Outer toe panel (3rd piece) Select models only.

SELECT MODELS

H JHH_

Avoid Scalding or Electrical Shock Hazard7 /

Make sure the water supply and electrical supply ar_

shut off before installation or service, j

After locating the proper place for your new dishwasher,

you will need to make any required openings to allow for

passage of the water, drain and electrical line. In order to

avoid interference with the dishwasher when sliding it into the

cabinet, place your openings within the dimensions shown

in Figure 3 below.

NOTE: This dishwasher is designed to be enclosed on the top

and both sides by standard residential kitchen cabinetry.

Select a location as close to the sink as possible for easy

access to water supply and drain lines.

For proper dishwasher operation and appearance, ensure

that the enclosure is square and has the dimensions shown

in Figure 1 below.

If the dishwasher is to be installed in a corner, make sure that

there is adequate clearance to open the door. See Figure

2 below.

Checkclearance[

between /

dishwasherdoor / Countertop

andwall l

J J// I I \

Required Openings:

41/4"x 2" (108 x 52mm) -

4" x 2" (100 x 50mm) -

11/4"(32mm) diameter -

To pass the included electrical

supply junction box through to

an adjacent cabinet

To pass the included water

supply line toward the water

supply

To pass the dishwasher

drain hose toward the drain

connection

NOTE: If the incoming electric supply, water supply and

drain connections are all in the same cabinet, the one

4V4"x 2" (108 x 52mm) hole will be large enough for all three

to pass through.

Before sliding the dishwasher into the cabinet, remove the

hose clip at the back of the dishwasher as shown below

and discard.

Avoid Electrical Shock/Fire Hazard

Do not allow the electrical and water supply lines

to touch.

................... i............................ i...........

ELECTRICAL PREPARATION

Avoid Electrical Shock Hazard

Do not work on an energized circuit. Doing so

could result in serious injury or death. Only

qualified electricians should perform electrical

work. Do not attempt any work on the dishwasher

electric supply circuit until you are certain the

circuit is de=energized.

Avoid Fire Hazard

Make sure electrical work is properly installed.

Only qualified electricians should perform

electrical work.

Electrical Supply

The customer has the responsibility of ensuring that the

dishwasher electrical installation is in compliance with all

national and local electrical codes and ordinances. The

dishwasher is designed for an electrical supply of 120V,

60 Hz, AC, connected to a dishwasher-dedicated, properly

grounded electrical circuit with a fuse or breaker rated for 15

amps. Electrical supply conductors shall be a minimum #14

AWG copper wire rated at 75°C (167°F) or higher.

Avoid Fire Hazard

Make sure there are no loose electrical connections.

Make sure all electrical connections are properly

made.

Electrical Connection

The dishwasher electrical supply junction box and dedicated

receptacle must be mounted in an accessible cabinet

adjacent to the dishwasher (do not mount the junction box

or receptacle behind the dishwasher). You will need a

41/4'' x 2" (108 x 51mm) opening throught the cabinet in

order to pass the junction box through (see Figure 4). If the

opening is made through wood, sand it smooth. Ifthe opening

is made through metal, use the included protective grommet

or other approved method to protect wiring from damage.

Use the four screws included (or appropriate fastener) in the

parts bag to securely mount the junction box so that it can

be easily accessed (see Figure 4). The electrical supply can

be connected in two ways:

::'Pla'c'°e'1

Id Wiring

Bectdcal Supply} / /

Figure 4

junction box and I

three prong plug I

are included 1

with dishwasher.//

Figure 5

Grounding Instructions

The dishwasher must be properly grounded before

operating. This appliance must be connected to

a grounded metal permanent wiring system, or an

equipment grounding conductor must be run with the circuit

conductors and connected to the equipment grounding

terminal or lead on the dishwasher. Make sure that the

dishwasher is connected to a suitable ground in compliance

with all local codes or, in the absence of a local code, with

the NATIONAL ELECTRICAL CODE in the United States or

the CANADIAN ELECTRIC CODE C22.1-1atest edition in

Canada as well as any provincial/state or municipal or local

codes that apply.

Dishwasher Electrical Rating

Volts Hertz Amperes Watts

120 60 12 1,300

(max)

Method A - Three prong plug and receptacle

Use the included three-prong plug and junction box to

connect to a dedicated household receptacle. Make sure

the household receptacle meets the electrical supply

requirements as well as national and local codes.

permanently connect to household or field wiring:

Remove the dishwasher electrical supply junction box

cover and connect to the power supply cord from the

house installation, (see Figure 5).

Remove 2" to 3" (51 - 76mm) of the outer casing of the

household or field supply wiring as shown in Figure 6.

Remove 3/8" to 1/2" (10 - 13mm) of the insulation from

each wire as shown in Figure 6.

2"- 3" 11

(51mm - 76mm). I

3/8"-1/2" I I

(10mm - 13ram)

Figure 6

Insert the bare copper or green wire(ground) to the

"G" ground connection "___L_" of the terminal block

and securely tighten the terminal block screw (see

Figure 5).

Insert the white (neutral) wire to the "N" connection of

the terminal block and securely tighten the terminal block

screw.

Insert the black(hot) wire to the "L" connection of the

terminal block and securely tighten the terminal block

screw.

Check all electrical connections to make sure they are

secure and then attach the junction box cover with the 4

screws.

Avoid Electrical Shock Hazard

To avoid possible injury or property damage,

care should be exercised when the dishwasher is

installed or removed to reduce the likelihood of

damage to the power cord.

Hot Water Supply

The hot water heater should be set to deliver approximately

120° F (49° C) water to the dishwasher. Water that is too

hot can cause some detergents to lose effectiveness. Lower

water temperatures will increase run times. The hot water

supply pressure must be between 15 - 145 psi (1 - 10 bar).

IMPORTANT NOTES:

If using a solder joint instead of a compression fitting, be

sure to make all solder connections before connecting the

water supply line to the dishwasher.

Make sure there are no sharp bends or kinks in the water

line that might restrict water flow.

Always use the appropriate seal when making plumbing

connections.

Before connecting the water supply line to the dishwasher,

flush the incoming water line for approximately 5 minutes

to clear any foreign material.

Turn on the water supply and check for leaks after

connections are made.

Avoid Scald Hazard

Do not perform any work on a charged hot water

line. Serious injury could result. Only qualified

plumbers should perform plumbing work. Do not

attempt any work on the dishwasher hot water

supply plumbing until you are certain the hot water

supply is shut off.

Temperatures required for soldering and sweating

will damage the dishwasher. If plumbing lines

are to be soldered or sweated, keep the heat

source at least 6 inches (152.4 mm) away from

the dishwasher.

Water Supply Shut Off Valve

Install an easily accessible shut-off valve (not supplied) in

the hot water supply line, as shown in Figure 7. All solder

connections must be made before the water line is connected

to the dishwasher.

Connecting the Hot Water Supply

There are two plastic corrugated hoses that exit the back of

the dishwasher. The larger hose, with the brass fitting on the

end, is the water supply hose to the dishwasher (the other

hose is the dishwasher drain hose). You will need a 3"x 13/4''

(76 x 45mm) opening through the cabinet to pass the dish-

washer water supply line through toward the shut off valve.

Figure 7

To connect the hot water supply:

1. Assemble the water supply adaptor fitting from the

parts bag onto the dishwasher water supply hose. This

connection does not require Teflon brand tape.

2. Pass the dishwasher water supply line with attached

adaptor through the opening toward the water shut off

valve. Take care not to allow the hose to kink or twist

behind the dishwasher.

3. Connect the dishwasher water supply line with adaptor to

the water shut off valve. You will need to use an approved

dishwasher water supply line with the correct fittings for

this connection. Always use the appropriate seal when

making plumbing connections.

NOTE: The end of the dishwasher water inlet hose is

heavy and will need to be supported. It is best to lay the

end on the cabinet floor as shown in Figure 7.

4. After all connections are made, turn on the hot water and

check for leaks.

The dishwasher drain hose may be connected to the house-

hold or field drain plumbing in one of four ways. You will need

a 1t/4'' diameter hole in order to pass the drain hose through

the cabinet.

1 Directly to the undersink dishwasher drain connection, as

shown in Figure 8.

2 Directly to a disposer dishwasher drain connection, as

shown in Figure 9.

3 To the undersink dishwasher drain connection through an

air gap, as shown in Figure 10.

4 To a disposer dishwasher drain connection through an air

gap, as shown on Figure 11.

iMPORTANT NOTES:

If local ordinance require an air gap, install it according

to the manufacturer's instructions.

If the dishwasher drain hose is to be connected to a

disposer dishwasher drain connection, remove the plug

from the disposer's dishwasher drain connection.

The dishwasher drain hose must have one place along

its length that is securely attached 20 inches above the

cabinet floor.

The drain hose length can be extended if necessary. The

maximum length of the drain hose, including the hose

leading to the air gap, is 150 inches.

_, • • j

Figure 8

Figure 10

Non-Metallic Tie

Figure 9

Figure 11

For a large port, use the drain hose as it is.

1. For a small port, insert the rubber drain hose adaptor

into the drain hose end.

2. Obtain the Rubber Drain HoseAdaptor spring clamp from

the Dishwasher Installation Kit (do not substitute).

3. Insert the dishwasher drain hose into the end of the

drain hose (see Figure 12). Be sure to fully insert the

drain hose.

4. Use the clamp provided to attach the Rubber Drain Hose

Adaptor to the house plumbing

Before installing the supplied countertop mounting

brackets, decide which method of securing the

dishwasher into its enclosure will be used. Once the

mounting brackets are installed on the dishwasher,

removing them is difficult and will damage the

mounting brackets and the dishwasher.

The dishwasher can be secured into its enclosure in two

ways:

1. Top Mount is used for countertops made of wood or

other materials that can easily drilled. Orient the mount-

ing brackets as shown in Figure 14, and position the two

small tabs on the mounting brackets over the two slots

on the dishwasher's front corners. Push the mounting

brackets down firmly to insert the tabs into the slots.

Figure 12

Figure 13

Top Mount

Figure 14

Side Mount is used for countertops made of marble,

granite, or other very hard materials that cannot be easily

drilled. Bend the mounting brackets along the small

holes and in the same direction as the two small tabs.

Orient the mounting brackets as shown in Figure 15, and

position the two small tabs on the mounting brackets

over the two slots on the dishwasher's front corners.

Push the mounting brackets down firmly to insert the

tabs into the slots.

Figure 15

Side Mount

Avoid Tip Over Hazard

Do not use the dishwasher until it is completely

installed. When opening the door on an uninstalled

dishwasher, carefully open the door while

supporting the rear of the unit. Failure to follow

this warning can result in serious injury.

~12mm/0.5 ''

LEVELING THE DISHWASHER

The unit should now be ready to slide into the cabinet

opening. Toavoid scratching the floor, use floor protection and

caution when sliding the dishwasher into the cabinet. Make

sure that the hoses and cords do not bunch up behind the

unit or kink as you slide the unit back. Make certain to slide

the unit into place before raising the leg levelers.

Level the dishwasher horizontally by turning feet clockwise

to raise or counter-clockwise to lower front of the unit.

Level the dishwasher vertically by turning center screw to

raise or lower the back.

Figure 16

Figure 18

For Side Mount - Stone Countertop

SECURING THE DISHWASHER

1. Drive the mounting screws through the holes in the

mounting brackets as shown for Top or Side Mount.

2. After the unit is installed in the enclosure, leveled and

secured, lock the two front leg levelers in place by driving

the enclosed leg leveler locking screws into each screw

boss located in front of the levelers. See Figure 18.

3. Tighten screws until they are flush with the surface of the

bosses.

mm/0.1"

For Top Mount - Wooden

Figure 17

Your dishwasher comes with a three-piece toe panel(select

models) to allow height adjustment.

1. Position the slotted rear toe panel on the dishwasher first.

Allow it to rest on the floor.

2. Position the mating front toe panel on top of the rear toe

panel allowing the angled edge to rest on the mating edge

of the dishwasher.

3. Drive the two black screws (included) through the hole in

the toe panel to secure. Use the supplied screws to avoid

damaging the dishwasher. See Figure 19.

4. For models with outer toe panel (3rd piece) slide the

brackets (A) provided, into the slots of the toe panel you

just attached.

NOTE: Once you determine the correct position for the brackets,

remove the bracket and bend the metal tab. See Figure 20. This

ensures that the toe panel wont slide in further than you need.

5. Re-insert the brackets.

6. Attach the outer toe panel (L) onto the brackets and drive

the screws provided in place to secure the toe panel.

NOTE: The rubber piece should remain behind the outer

toe panel. Figure 19

,,lr

A %

Figure 20

Yourdishwasherrequiresno specialcareotherthan

thatdescribedintheCareandMaintenancesectionof

theUseandCareManual.Ifyouarehavinga problem

withyourdishwasher,beforecallingforserviceplease

refer to the Self Help sectionin the Use and Care

Manual.Ifserviceisnecessary,contactyourdealeror

installeroranauthorizedservicecenter.

Do notattemptto repairthe applianceyourself.Any

workperformedby unauthorizedpersonnelmayvoid

thewarranty.If you are havinga problemwith your

dishwasherandare notpleasedwiththe serviceyou

havereceived,pleasetakethefollowingsteps(in the

order listedbelow) untilthe problemis correctedto

yoursatisfaction:

1. Contactyour installeror the AuthorizedService

Contractorinyourarea.

2. E-mail us. See your Use and Care Manualfor

instructions.

3. Writeusattheaddressbelow:

BSHHomeAppliances,Corp.

5551McFaddenAvenue

HuntingtonBeach,CA92649

4. CallusattheCustomerServicephonenumber:

1-800-944-2904

Pleasebesuretoinclude(ifyouarewriting),orhave

available(ifyouarecalling),thefollowinginformation:

, Modelnumber

, Serialnumber

, Dateoforiginalpurchase

, Datetheproblemoriginated

, Explanationoftheproblem

, Daytimephonenumberwhereyoucanbereached.

Pleasemakeacopyofyourinvoiceandkeepitwiththis

manual.Thecustomermustshowproofofpurchaseto

obtainwarrantyservice.

lnstructions de s curit

Pour eviter tout dommage a la propriet6

ou des blessures OBSERVER TOUSLES

AVERTISSEMENTS.

Ces instructions sont destinees a I'utilisation par

un installateur qualifie seulement. Ce lave-vaisselle

doit _tre installe par un technicien ou un installateur

qualifie seulement.

En plus de ces instructions, le lave=vaisselle

doit _tre installe conformement aux codes et

reglementations electriques et de plomberie

(nationaux et Iocaux).

Lire et observer attentivement toutes les instructions

d'instatlation. Ceci permettra d'economiser temps

et argent tout en assurant la securit6 et un

rendement optimum du lave=vaisselle.

IMPORTANT

• Le tuyau de drainage du lave=vaisselle doit

@re installe avec une portion a au moins 20

po (508 mm) au=dessus du plancher d'armoire,

autrement le lave=vaisselle ne pourra drainer

adequatement.

• Ce lave=vaisselle est destine a un usage

residentiel seulement et non pour un usage

commercial.

• NOUVELLE INSTALLATION - s'il s'agit

d'une nouvelle installation, tout le travail de

construction doit @re fait avant d'installer le

lave=vaisselle.

• REMPLACEMENT- dans ce cas, v@ifier si les

connexions existantes sont compatibles avec

celle du nouveau lave=vaisselle et remplacer

les pieces au besoin.

• Cet appareil est conforme aux normes CAN/

CSA-C22,2 n°167/UL 749. II incombe

I'installateur et au proprietaire de determiner

si des exigences additionnelles s'appliquent

I'installation specifique.

• N'est pas destine a une utilisation

I'exterieur.

importantes

V6rifier le lave=vaisselle

Apres avoir deball6 I'appareil et avant I'installation,

s'assurer qu'il n'y a pas de dommages esthetiques

ou causes pendant le transport. Rapporter tout

dommage immediatement. Les dommages

esthetiques doivent _tre rapportes dans un delai

de 30 jours suivant I'installation.

REMARQUE : ne pas jeter les sacs ni I'emballage

tant que I'installation n'est pas complet6e.

Risques d'ordre g6n6ral

Ne pas utiliser le lave-vaisselle avant que 'installation

ne soit completement terminee. Pour ouvrir la porte

d'un lave-vaisselle encore non installe, il faut le faire

soigneusement en soutenant I'arriere du lave-vais-

selle. Le lave-vaisselle peut en effet tomber en avant

si cet avertissement n'est pas respecte et cela peut

causer de graves degats.

Avant I'installation des fixations en forme de <<L >)(pour

certains modeles), il faut choisir la methode qui sera

utilisee pour I'ouverture du lave-vaisselle. Une fois que

ces fixations sont installees sur le lave-vaisselle, il est

difficile de les retirer et cela risque d'endommager les

fixations et le lave-vaisselle.

Sous certaines conditions, le systeme d'eau chaude

peut emettre du gaz hydrogene si le lave-vaisselle

n'a pas ete utilise pendant plusieurs semaines. Le

gaz hydrogene est un gaz explosif. Avant de refaire

fonctionner le lave-vaisselle apres une Iongue periode,

faire couler I'eau du robinet le plus proche dans une

zone bien ventilee jusqu'a ce qu'il n'y ait plus aucun

bruit de gaz ou toute autre preuve de sa presence.

Les temperatures necessaires pour souder et ex-

suder risquent d'endommager la base et la soupape

d'admission d'eau du lave-vaisselle. Si la tuyauterie

a besoin d'une soudure ou d'une exsudation, placer

la source de chaleur a au moins 6 po (152,4 mm) de

la base et de la soupape d'admission d'eau du lave

vaisselle.

Vouloir retirer un des couvercles ou vouloir deplacer le

lavevaisselle de son emplacement peut endommager

les tuyaux d'eau chaude et I'alimentation electrique.

Effectuer ces manipulations avec soin.

Risques d'electrocution et d'incendie

Les cables electriques et les tuyaux d'alimentation

en eau ne doivent pas etre en contact. Des conduits

independants sont prevus a cet effet sous le lave-

vaisselle.

Effectuer des travaux electriques Iorsque le courant

est ouvert peut provoquer des blessures graves

ou la mort. Seul un electricien qualifie peut realiser

des manipulations electriques. N'effectuer aucune

manipulation electrique sur le lave-vaisselle tant que

le courant n'est pas clairement hors tension.

S'assurer que les travaux electriques soient

correctement realises. II ne doit y avoir aucun cable

electrique mal fixe et aucun raccordement electrique

mal realis&

Le client a la responsabilite de verifier que I'installation

electrique du lave-vaisselle soit conforme aux normes

electriques nationales et regionales. Le lave-vaisselle

a ete con_u pour fonctionner avec une alimentation

electrique de 120V, 60Hz, c.a., et doit etre branche

a un circuit electrique adapte au lave vaisselle

correctement relie a la terre et protege par un fusible

de 15 amperes. Les conducteurs electriques doivent

etre composes de ills en cuivre n°14 AWG minimum

ayant une resistance thermique minimale de 75°C

(167°F).

Ce lave-vaisselle doit etre relier a la terre soit en le

connectant au support metallique qui est relie a la terre

soit en branchant la prise du terre du lave-vaisselle a

une prise de courant appropriee, elle- m_me reliee a

la terre. Ne pas utiliser de rallonge.

Risques de brQlure_

Ne pas effectuer de travaux de plomberie sur un tuyau

rempli d'eau chaude. II y a des risques de blessures

graves. Seul un plombier qualifie peut realiser des

manipulations de plomberie. N'effectuer aucun travail

de plomberie sur le lave-vaisselle tant que I'arrivee

d'eau chaude n'est pas clairement fermee.

Ne pas serrer trop fort le coude de 90 °. Cela peut en-

dommager la soupape d'admission d'eau et provoquer

une fuite de I'eau.

Les temperatures necessaires pour souder et exsuder

dsquent d'endommager la soupape d'admission

d'eau du lave-vaisselle. Si la tuyauterie a besoin

d'une soudure ou d'une exsudation, placer la source

de chaleur a au moins 6 pouces (152,4 mm) de la

soupape d'admission d'eau du lave-vaisselle.

II est necessaire de verifier les normes relatives aux

travaux de plomberie pour toute installation. Tout tra-

vail de plomberie doit etre conforme avec les normes

nationales et regionales.

Ces instructions sont relatives a une methode

d'installation utilisant des tuyaux d'alimentation en

acier inoxydable tresse et des tuyaux d'eau chaude

PEX. Si la tuyauterie est en cuivre, ou tout autre

materiau, pour I'alimentation en eau, il fau faire appel a

un plombier qualifie pour une installation appropriee.

Marteau

Scie-cloche

F ............................. __b)

Cl6 a tuyau

Cl6 r6glable

Ruban a mesurer Tournevis &

lame plate

Tournevis Phillips

Tournevis -[-20

Coupe-ill

Outil & d6-

nuder

[©,

Niveau

C&ble d'alimentation 61ectrique - minimum #14AWG, 2 conduc-

teurs, 1 mise a la terre, conducteurs en cuivre isol6s cot6 75 °C

ou plus

Canalisation d'alimentation en eau chaude - tube en cuivre ou

en m6tal tress6 D.E. 3/8 po maximum

Soupape d'arr6t et raccords appropri6s pour la canalisation

d'alimentation en eau chaude (tube en cuivre, raccord de com-

pression ou tuyau tress6)

Connecteur de conduit ou r6ducteur list6s UL, m_me si un

r6ducteur est inclus avec la bofte de jonction, un autre r6ducteur

peut _tre n6cessaire si I'onfixe le c&blage d'excitation directement

sur le bloc de bornes.

_ I_::i_

A Bras gicleur pour grands articles

B Vis du panneau inf@ieur

g Fixations

D Vis de fixations

E Panneau inf@ieur

F Vis du panneau inf@ieur

G Pince & ressort (pour tuyau)

H Raccord adaptateur pour alimentation en eau

I Rondelle de protection flexible pour fil electrique

J Fixations pour panneau inf@ieur

K Crochet et bande attache

L Panneau inf@ieur exterieur

SELECT MODELS

(:D--oO

E_viterles brOlures et les chocs _lectriques. I

S'assurer que les alimentations en eau et @lectrique I

sont ferm_es avant d'effectuer rinstallation ou le|

service j

REMARQUE "cet appareil est congu pour etre encastr6 sur

le dessus et les c6t6s par des armoires de cuisine r6siden-

tielle standard.

Choisir un emplacement aussi pros que possible de 1'6vier

pour un acces ais6 & I'alimentation en eau et au tuyau de

drainage.

Pour une apparence et un fonctionnement appropri6s du

lave-vaisselle, s'assurer que I'espace est d'6querre eta les

dimensions indiqu6es a la figure 1..

Apr_s avoir trouv6 I'emplacement pour I'appareil, il faut faire

les ouvertures n6cessaires pour les canalisations en eau,

61ectrique et de drainage. Afin d'6viter toute interf@ence au

moment d'ins@er le lave-vaisselle, faire les ouvertures selon

les dimensions donn6es a la figure 3.

J J// I I \

Si I'appareil est install6 dans un coin, s'assurer qu'il y a un

d6gagement suffisant pour ouvrir la porte, figure 2.

Verifiere .ande

d6gagement / travail

entrela portedu J

lave-vaisselle /

etle tour [

Pour _viter le risque de choc _lectrique et

d'incendie

Ne pas laisser les canalisations d'alimentation

_lectrique et en eau entrer en contact.

Ouverture requise:

4V4"x 2" (108 x 52mm) -

3"x 13/4" (100 x 50mm) -

11/4"(32mm) diameter -

Pour passer la bofte de jonc-

tion comprise par une armoire

adjacente

Pour passer la canalisation

d'alimentation en eau

Pour passer letuyau de drainage

vers la connexion du drain

REMARQUE : si I'alimentation 61ectrique, celle de I'eau et

les connexions de drain sont toutes dans la m6me armoire,

I'ouverture de 4 % x 2 po (108 x 52 mm) sera suffisamment

large pour les trois.

Avant d'ins@er le lave-vaisselle en place, enlever la pince

du tuyau a I'arri@e du lave-vaisselle, tel qu'il est indiqu6 ci-

dessous et la jeter.

................... i........................... i...........

i_viterles chocs _lectriques

Ne pas travailler avec un circuit sous tension.

Cela peut causer de serieuses blessures ou la

mort. Seul un electricien qualifie peut effectuer

le travail electrique. Ne pas tenter de travailler

sur le lave-vaisselle tant que le circuit electrique

n'est pas coup&

leviter les risques d'incendie

S'assurer que I'alimentation electrique est

adequatement installee. Seul un electricien

ualifie eut effectuer le travail.

Alimentation 61ectrique

Le consommateur est responsable afin de s'assurer que

I'installation 61ectrique du lave-vaisselle est conforme aux

codes 61ectriques Iocaux et nationaux. Le lave-vaisselle est

congu pour une alimentation 61ectrique de 120V, 60Hz, c.a.,

branch6 sur un circuit 61ectrique mis & la terre ad6quatement

et d6di6 a I'appareil, avec un fusible ou un disjoncteur cot6

15 amperes. Les conducteurs electriques doivent _tre un

minimum de #14 AWG, fil de cuivre cote pour 75 °C (167

°F) ou plus.

I_viter les risques d'incendie

S'assurer que les connexions _lectriques ne

sont pas I_ches et qu'elles sont ad_quatement

branch_es.

instructions de raise a la terre

L'appareil dolt etre adequatement mis & la terre avant de

le faire fonctionner. Cet appareil dolt 6tre branche sur un

systeme de c&blage permanent en metal, mis a la terre ou

un conducteur de mise a la terre d'equipement dolt etre

branche sur la borne de mise a la terre d'equipement ou

le fil du lave-vaisselle. S'assurer que le lave-vaisselle est

branche sur une mise a la terre appropriee conformement

tousles codes ou en I'absence de codes Iocaux, avec le

CODE NATIONAL D'_:LECTRICITt_ aux E.-U. ou le CODE

D't_LECTRICITt_ DU CANADA, C22,1, derniere edition au

Canada ainsi qu'aux codes Iocaux, municipaux, provinciaux

qui s'appliquent.

Connexion 61ectrique

La bofte de jonction d'alimentation electrique du vaisselle

et la prise dediee doivent _tre install6es dans une armoire

adjacente au lave-vaisselle (ne pas les installer derriere

I'appareil). IIfaut une ouverture de 4 1/4 x 2 pc (108 x 51 mm).

Si I'ouverture est faite dans le bois, sabler le rebord ; si dans

le m6tal, utiliser la rondelle de protection ou autre m6thode

approuvee pour proteger le c&blage de tout dommage.

Utiliser les 4 vis comprises (ou attaches appropriees) du

sac de pieces pour fixer la bofte de jonction afin qu'elle soit

accessible (figure 4). L'alimentation electrique peut etre

branchee de deux fagons:

iiiii

Figure 4

/ /\\rd--wit_'

/ / _ junction box and

J/ _ I three prong plug

V " I are included

k with dishwasher,

Figure 5

Cote 61ectrique du lave=vaisselle

Volts Hertz Amperes Watts

120 60 12 1,300

(max)

M_thode A - fiche _ 3 broches et prise

Utiliser la fiche a 3 broches et la bofte de jonction comprise

pour brancher sur une prise residentielle dediee. S'assurer

que la prise residentielle repond aux exigences d'alimentation

electrique ainsi qu'au codes nationaux et Iocaux (figure 4).

Pour brancher de fa£on permanente au c_blage r@si-

dentiel :

1. Enlever le couvercle de la boite de jonction 61ectrique

du lave-vaisselle et d6brancher le cordon fourni & fiche

3 broches du bloc de bomes en d6vissant les vis

correspondantes (figure 6).

Figure 6

(51mm - 76mm). I

3/8" - 1/2"

(10mm - 13mm)

Alimentation en eau chaude

Le chauffe-eau dolt etre r6g16 pour donner une eau chaude

d'une temp@ature approximative de 120 °F (49 °C) pour le

lave-vaisselle. Si I'eau est trop chaude, le d6tergent perd de

son efficacit6 ;si elle est trop basse, la dur6e est prolong6e.

La pression de I'alimentation en eau chaude dolt etre entre

15 et 145 Ib/po2 (1 a 10 barres).

REMARQUES IMPORTANTES:

• Si I'on utilise un joint de soudure au lieu d'un raccord

compression, s'assurer que toutes les connexions

soud6es sont faites avant de brancher la canalisation

d'eau sur le lave-vaisselle.

• S'assurer que la canalisation en eau n'est pas coinc6e,

pinc6e ni pli6e ; cela obstrue le d6bit d'eau.

• Toujours utiliser les joints appropri6s au moment de faire

les connexions de plomberie.

• Avant de brancher la canalisation d'alimentation en eau

sur le lave-vaisselle, faire couler I'eau de la canalisation

pendant environ 5 minutes pour enlever tout objet

6tranger.

• Ouvrir I'alimentation en eau et v@ifier s'il y a des fuites

une fois les connexions termin6es.

2. Remplacer le r6ducteur de tension sortant compris

avec un r6ducteur appropri6 pour c_blage 61ectrique

r6sidentiel.

3. Enlever 2 a 3 po (51 a 76 mm) de la gaine ext@ieure du

c&ble d'alimentation, figure 5. Enlever 3/8 a ½ po (10

13 mm) de I'isolant pour chaque ill, figure 5.

4. Ins@er le fil de cuivre d6nud6 ou vert (mise a la terre) sur

la connexion G de mise a la terre ,,I,, du bloc de bornes

et visser en place de fagon s6curita]Te a la vis du bloc de

bornes (figure 6).

5. Ins@er le fil blanc (neutre) sur la connexion N du bloc de

bornes et visser a la vis du bloc de bornes.

6. Ins@er le fil noir (sous tension) sur la connexion L du bloc

de bornes et visser a la vis du bloc de bornes.

7. V@ifier toutes les connexions 61ectriques afin de s'assurer

qu'elles sont bien en place, puis remettre le couvercle sur

la boTte de jonction avec les 4 vis.

I_VITER LE RISQUE DE BRULURES

Ne pas travailler avec une canalisation d'eau

chaude, il peut en r_sulter de s_rieuses blessures.

Seul un plombier qualifi_ peut effectuer le travail.

II faut fermer la canalisation d'eau chaude.

La temperature requise pour une soudure peut

endommager le lave=vaisselle. Si la canalisation

doit Ctre soud_e, garder la source de chaleur a au

moins 6 po (152,4 mm) du lave-vaisselle.

€:viter les risques de chocs _lectriques

Pour @viter tout dommage a la propri@t@ ou

des blessures, faire trCs attention au moment

d'installer ou d'enlever le lave-vaisselle afin de

ne pas endommager le cordon d'alimentation.

La page est en cours de chargement...

Thermador DWHD651GFP/18 Guide d'installation

Marque: Thermador

Modèle: DWHD651GFP/18

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Thermador DWHD651GFP/18 Installation guide
español: Thermador DWHD651GFP/18 Guía de instalación

Thermador DWHD651GFP/18 Guide d'installation

Thermador DWHD651GFP/18 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents