wattstopper FS-C1 Guide d'installation

wattstopper
Marque
wattstopper
Modèle
FS-C1
Taper
Guide d'installation

Ce manuel convient également à

Wattstopper
®
Fixture Mount Power Pack (version 2)
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 23949 – 08/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: FS-PP
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Power .......................................................................................... 120/277/347VAC, 60Hz
Relay Type ....................................................... Form C with Zero Crossing on N.O. only
Output ................................................................70mA @ +24VDC with relay connected
Load Requirements
@120VAC ................................................................... 5.0A (N/O), 3.0A (N/C), 1/6hp
@277VAC ................................................................... 4.3A (N/O), 2.5A (N/C), 1/6hp
@347VAC ...............................................................................3.4A (N/O), 2.0A (N/C)
Low Voltage Connections .............................................RJ45 connection to FS sensors
..................................................................................... Control in, common, +24VDC
Line and Load Connections ................................................. 12-18AWG screw terminals
Terminal Torque Rating ........................................... 4.428 inch pound-force (0.5Nm)
Operating Temperature ............................................................ 32° to 131°F (0° to 55°C)
Dimensions ........................................................... 7.5” x 0.87” x 1.0” (190 x 22 x 25mm)
FS-PP V2
Model:
Fixture Sensor
Power Pack
120/277/347VAC, 60Hz
@120VAC 5A (N/O)
3A (N/C)
@277VAC 4.3A (N/O)
2.5A (N/C)
@347VAC 3.4A (N/O)
2A (N/C)
0
3392 r2
Strip Gauge
AC INPUT
www.legrand.us
800.879.
8585
DESCRIPTION AND OPERATION
The FS-PP v2 power pack supplies low voltage power to FS series occupancy sensors and switches line voltage in response to control
signals from the sensors. The FS-PP v2 is designed for installation inside the lighting fixture housing.
A 6’ long cable fitted with a male RJ45 plug is supplied with each FS series 24VDC occupancy sensor. The
FS-PP has a corresponding female RJ45 receptacle. This cable carries power to the sensor and lighting
control signals to the power pack.
Each Watt Stopper FS-PP v2 can supply power for up to seven FS series low voltage sensors. FS-CK
accessory kits are required to connect multiple sensor or multiple power pack wiring configurations. Wiring
connected to the RJ45 is limited to an aggregate total of 100’.
High voltage connections should use at least 16 gage wire. Always check local building codes.
INSTALLATION
1. Determine an appropriate mounting location inside the light fixture.
2. Use the holes or mounting slots at both ends of the power pack to secure it to the fixture.
3. Connect wires to load as described in the wiring section.
4. Connect wires to electrical supply as described in the wiring section.
5. Connect the RJ45 from the sensor to the RJ45 on the power pack.
6. Restore power from the circuit breaker.
High voltage AC
input wiring
Low voltage RJ45
connection to FS sensor
Relay Output
to load
Green LED - Operation monitor
COM
N/O
N/C
03500r1
ISOLATED RELAY
OUTPUTS
TO LOAD
RJ45
TO SENSOR
www.legrand.us
800.879.8585
FS-PP V2
Model:
Fixture Sensor Power Pack
120/277/347VAC, 60Hz
@120VAC 5A (N/O)
3A (N/C)
@277VAC 4.3A (N/O)
2.5A (N/C)
@347VAC 3.4A (N/O)
2A (N/C)
GROUND
NEUTRAL
LINE
0339 2r2
Strip Gauge
12-18AWG
CU wire only
88T9
Appliance
Control
LISTED
AC INPUT
Fig. 1: FS-PP v2 wire connections and operation monitor LED
High voltage wiring:
12-18 AWG, Cu Only
Strip Gauge
1/2"
12.7mm
WARNING: TURN THE POWER OFF
AT THE CIRCUIT BREAKER BEFORE
INSTALLING THE POWER PACK
2
WIRING A SINGLE SENSOR
Fig 2: FS-PP v2 direct wiring to lighting load
Com
N/O
RJ45
Plug
from FS
sensor
Line
120/277/347 Volts AC
Neutral
Ground
Green Operation
LED
COM
N/O
N/C
03500r1
ISOLATED RELAY
OUTPUTS
TO LOAD
RJ45
TO SENSOR
Lighting
Load
Neutral
FS-PP V2
Model:
Fixture Sensor Power Pack
120/277/347VAC, 60Hz
@120VAC 5A (N/O)
3A (N/C)
@277VAC 4.3A (N/O)
2.5A (N/C)
@347VAC 3.4A (N/O)
2A (N/C)
GROUND
NEUTRAL
LINE
03392r2
Strip Gauge
12-18AWG
CU wire only
88T9
Appliance
Control
LISTED
AC INPUT
www.legrand.us
800.879.8585
Fig 3: FS-PP v2 wiring to 0-10V dimming ballast
N/C
Grey
Com
Violet
0-10VDC
0-10VDC
Dimming Ballast
Line Voltage
Inputs to
Ballast
Outputs
to Lamps
Line
120/277/347 Volts AC
Neutral
Ground
Green Operation
LED
COM
N/O
N/C
03500r1
ISOLATED RELAY
OUTPUTS
TO LOAD
RJ45
TO SENSOR
RJ45
Plug
from FS
sensor
FS-PP V2
Model:
Fixture Sensor Power Pack
120/277/347VAC, 60Hz
@120VAC 5A (N/O)
3A (N/C)
@277VAC 4.3A (N/O)
2.5A (N/C)
@347VAC 3.4A (N/O)
2A (N/C)
GROUND
NEUTRAL
LINE
03392r2
Strip Gauge
12-18AWG
CU wire only
88T9
Appliance
Control
LISTED
AC INPUT
www.legrand.us
800.879.8585
CONTROL CONFIGURATIONS
Standard connection between FS Sensor and FS-PP Power Pack
FS-PP
Any 24VDC
FS-Sensor
Fig 4: One sensor controlling one power pack
Fig 5: One sensor controlling Two Power Packs
One FS sensor connected to two FS-PP
FS-C4
FS-C3 (3')
or
FS-C1
(10' shown)
FS-PP
FS-PP
Any 24VDC
FS-Sensor
3
FS-C3 (3' shown)
or
FS-C1 (10')
FS-C4
FS-PP
Any 24VDC
FS-Sensor
Any 24VDC
FS-Sensor
Fig 6: Two Sensors controlling One Power Pack
Fig 7: Two Sensors controlling Two Power Packs
FS-C4FS-C4
FS-C3 (3')
or
FS-C1
(10' shown)
FS-PPFS-PP
Any 24VDC
FS-Sensor
Any 24VDC
FS-Sensor
TROUBLESHOOTING
Lights will not turn on:
• Sensor LED does not flash:
▸ Is green power pack LED on?
If yes, check RJ45 connections at sensor and power pack.
If no, check circuit breaker and wiring to power pack.
▸ Check all wire connections.
• LED does flash:
▸ Check all wire connections and verify the load wire is tightly secured.
• If lights still do not turn on, call 800.879.8585 for technical support.
Lights will not turn off:
The time delay can be set from 30 seconds to 30 minutes. Ensure that the time delay is set to the desired delay and that there is no
movement within the sensor’s view for that time period.
• To quickly test the unit for proper operation, turn the time delay to minimum and move out of the sensor’s view. Lights should turn
off after 30 seconds.
• If lights still do not turn off, call 800.879.8585 for technical support.
800.879.8585
www.legrand.us/Wattstopper
No. 23949 – 08/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
Sensors and power packs are White.
Catalog # Description
FS-PP v2 Fixture Mount Power Pack: 120/277/347VAC, 60Hz with NO/NC Relay output
FS-105 Ceiling tile mount, low voltage PIR occupancy sensor with adjustable time delay and light level
FS-205 Fixture mount, low voltage PIR occupancy sensor with adjustable time delay and light level
FS-305 Fixture or Ceiling tile mount, low voltage PIR occupancy sensor, adjustable time delay
FS-405 Fixture mount, low voltage PIR occupancy sensor w/20’ diameter coverage, adjustable time delay and light level
FS-505 Fixture mount, low voltage ultrasonic occupancy sensor
FS-505C Same as FS-505, with directional cones
FS-C1 One 10’ cable with a shielded RJ45 male connector at each end
FS-C2 One 6” (152mm) cable with 3 flying leads at one end and a shielded RJ45 male connector at the
other
FS-C3 One 3’ cable with a shielded 90° RJ45 male connector at one end and a shielded straight male RJ45 connector at
the other end, for space-limited areas
FS-C4 Shielded RJ45 splitter with female to dual female receptacles
FS-C5 Shielded RJ45 male-to-male coupler
ORDERING INFORMATION
10' (3m)
3' (914mm)
6" (152mm)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

wattstopper FS-C1 Guide d'installation

wattstopper
Marque
wattstopper
Modèle
FS-C1
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents