Wattstopper

®

Fixture Mount Power Pack (version 2)

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 23949 – 08/16 rev. 1

Catalog Number • Numéro de Catalogue • Número de Catálogo: FS-PP

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Power .......................................................................................... 120/277/347VAC, 60Hz

Low Voltage Connections .............................................RJ45 connection to FS sensors

..................................................................................... Control in, common, +24VDC

Line and Load Connections ................................................. 12-18AWG screw terminals

Terminal Torque Rating ........................................... 4.428 inch pound-force (0.5Nm)

Operating Temperature ............................................................ 32° to 131°F (0° to 55°C)

Dimensions ........................................................... 7.5” x 0.87” x 1.0” (190 x 22 x 25mm)

FS-PP V2

Model:

Fixture Sensor

Power Pack

DESCRIPTION AND OPERATION

The FS-PP v2 power pack supplies low voltage power to FS series occupancy sensors and switches line voltage in response to control

connected to the RJ45 is limited to an aggregate total of 100’.

High voltage connections should use at least 16 gage wire. Always check local building codes.

INSTALLATION

1. Determine an appropriate mounting location inside the light fixture.

2. Use the holes or mounting slots at both ends of the power pack to secure it to the fixture.

3. Connect wires to load as described in the wiring section.

4. Connect wires to electrical supply as described in the wiring section.

5. Connect the RJ45 from the sensor to the RJ45 on the power pack.

6. Restore power from the circuit breaker.

• LED does flash:

▸ Check all wire connections and verify the load wire is tightly secured.

• If lights still do not turn on, call 800.879.8585 for technical support.

Lights will not turn off:

The time delay can be set from 30 seconds to 30 minutes. Ensure that the time delay is set to the desired delay and that there is no

movement within the sensor’s view for that time period.

• To quickly test the unit for proper operation, turn the time delay to minimum and move out of the sensor’s view. Lights should turn

off after 30 seconds.

• If lights still do not turn off, call 800.879.8585 for technical support.

800.879.8585

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of Wattstopper for

consequential damages arising out of, or in

connection with, the use or performance of this

removal, installation or reinstallation.

están libres de defectos en materiales y mano

de obra por un período de cinco (5) años. No

existen obligaciones ni responsabilidades por

parte de Wattstopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

FS-405 Fixture mount, low voltage PIR occupancy sensor w/20’ diameter coverage, adjustable time delay and light level

FS-505 Fixture mount, low voltage ultrasonic occupancy sensor

FS-505C Same as FS-505, with directional cones

FS-C1 One 10’ cable with a shielded RJ45 male connector at each end

FS-C2 One 6” (152mm) cable with 3 flying leads at one end and a shielded RJ45 male connector at the

other

FS-C3 One 3’ cable with a shielded 90° RJ45 male connector at one end and a shielded straight male RJ45 connector at

the other end, for space-limited areas

FS-C4 Shielded RJ45 splitter with female to dual female receptacles

FS-C5 Shielded RJ45 male-to-male coupler