Extron MLC 55 R Manuel utilisateur

Extron
Marque
Extron
Modèle
MLC 55 R
Taper
Manuel utilisateur

Ce manuel convient également à

Product Category
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sour
ce.
MLC 55 Series • Setup Guide
for MLC 55 RS and MLC 55 RS VC
The MLC 55 Series are keypad controllers with dual-color, backlit
buttons for common AV functions such as power, input selection,
and volume in single-display applications. RS-232 unidirectional
serial and IR ports provide universal display control.The
MLC 55 RS VC has a volume control module that lets you raise
and lower the volume on an Extron amplier with a remote volume
control port, such as the MPA 152 or MPA 401. These products
can be wall-mounted in one-gang or two-gang junction boxes or
using the provided mounting bracket (“mud ring”).
For full installation, conguration, and operation details, see the
MLC 55 Series User Guide, available at www.extron.com.
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués uniquement par un électricien qualié.
• All electrical installation should be performed by qualied personnel in accordance with local and national building
codes, re and safety codes, and local and national electrical codes.
• Toute installation électrique devrait être effectuée par un personnel qualié, conformément aux codes du bâtiment, aux
codes incendie et sécurité, et aux codes électriques locaux et nationaux.
• Ensure that the electrical box is properly grounded.
• Assurez vous que le boîtier d’encastrement est correctement mis à la terre.
Installation Steps
1. Prepare the site. The MLC 55 RS can be mounted to a standard US one-gang junction box or a one-gang mud ring
(provided). The MLC 55 RS VC can be mounted to a standard US two-gang junction box or a two-gang mud ring (provided).
a. Install the junction box, following the instructions provided with it. If using a mud ring, install it according to the
instructions in the MLC 55 Series User Guide.
b. Prepare and pull the cables through the junction box or mounting bracket.
2. If desired, remove and replace button labels. To replace a button label:
a. Remove the faceplate from the unit.
The MLC faceplate is held in place on the unit by four magnets at its
corners. Grasp the unit rmly with one hand and, with the other, pull the
faceplate off the unit starting with a corner.
b. Insert the small end of the provided pry tool into one of the four notches in
the corners of the clear button cap that contains the label to be changed.
Rotate the pry tool carefully to avoid damaging the button, until the cap
pops off of the diffuser.
RESET
PC
VOL
VOL
VIDEO
1
DISPLAY
Extron
ON
PC
VIDEO
OFF
VOL
VOL
VOLUME
Extron
DISPLAY
ON
PC
VIDEO
OFF
VO
LUME
ON
PC
LAPTOP
MUTE
MLC 55 RS MLC 55 RS VC
Pry the clear cap
away from the
button at one corner.
Diffuser
Base
Insert the
button label.
Clear Button Cap
TEXT
Pry Tool
MLC 55 Series • Setup Guide (Continued)
c. Remove the current label from inside the button cap and replace it with the new one.
Tip: To avoid damaging the button label when removing it, turn the button cap upside down and tap it on a hard
surface until the label falls out. Alternatively, insert into the button cap a lightly adhesive tape or gum product
that will temporarily adhere to the label, to pick up and pull the label out.
d. Replace the button cap and label onto the diffuser and press it until it snaps into place.
3. Connect device cables to the rear panel Control port for
RS-232 or IR. Wire either of the following to the rear panel control
connector:
G
Tx IR
• RS-232 (uni-directional) control: Connect the RS-232 cable
from a display device or switcher to the Tx and G pins of the
control connector (see the diagram below).
• IR control: Connect a display device, switcher, or an IR
emitter to the IR and G connectors of the control port.
RS-232 Connection IR Emitter Connection
50'
(15 m max)
Ground (G)
IR Signal
IR Emitter
MLC 55 Rear Panel
Ground (G)
Transmit (Tx)
Ground (G)
Receive (Rx)
Display Device
MLC 55 Rear Panel
4. Connect an audio device cable to the volume control module (MLC 55 RS VC only):
Connect the remote volume control port of an Extron amplier to the 3-pole captive screw connector on the rear panel of the
MLC 55 volume control module, as shown at right. No software conguration is required for this module. In the illustration at
right, G = ground, C = volume control, and V = 10 VDC reference voltage.
Amplifier
Rear Panel
MLC 55 RS
VC
Rear Panel
V
C
G
VCG
10V
50mA
VCG
NOTES:
• Choose an Extron amplier that is capable of remote volume control and muting. Not all Extron ampliers have
remote volume control ports. The MPA 152 or MPA 401 are examples of the types of ampliers to use.
• Use shielded cable for audio connections to avoid inducing noise.
2
Product Category
5. Connect and apply power. Connect the included power supply to the 2-pole captive screw connector on the rear panel of
the MLC as shown below, then connect power to all devices in the system.
ATTENTION:
• Do not connect any external power supplies until you have read the Attention notications in the power supply
section of the user guide for that device.
• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section
«powersupply» du guide utilisateur pour cet appareil.
Ground
12 VDC input
Ground
all devices.
External
Power Supply
(12 VDC, 1 A max.)
1A MAX
100-240V 50-60Hz
MLC 55 Rear Panel
6. Configure the MLC buttons and ports:
a. Download the MLC 55, 62, and 64 series conguration software from the Extron website and install it.
b. Obtain device drivers for the devices to be connected to the MLC rear panel control port. Drivers can be downloaded
from www.extron.com. You can also obtain them using the conguration software via an Internet connection.
If unable to obtain a driver for your display device, you can create one using IR Learning (see the MLC 55, 62 and 64
Conguration Program help le).
c. Assign commands to the MLC buttons and ports as desired (see the MLC 55, 62 and 64 Series Conguration Program
help le for the procedures).
d. Remove the MLC faceplate and connect the MLC to
the computer, using a USB A to USB mini-B cable
between the MLC front panel USB port (shown at
right) and the USB port on your computer.
e. Upload the conguration le to the MLC.
NOTE: The volume control module of the
MLC 55 RS VC stands alone and requires no
configuration.
7. Test the system to ensure that the MLC is functioning
properly.
8. Correct the wiring or conguration if needed.
9. Mount the MLC to an electrical box or a mounting bracket
(see Mounting the MLC 55 on the next page).
Mounting the MLC 55
To mount the MLC 55 to a mud ring (US models only) or a junction box:
1. Remove the faceplate from the MLC as follows:
a. Grasp the unit rmly with one hand.
b. Starting at a corner, with the other hand pull the faceplate away from the metal mounting plate to which the unit is
attached magnetically.
2. Disconnect power from all devices at the source.
3
ON
OFF
RESET
E
PC
VOL
VOL
VIDEO
MLC 55 Front Panel
Without Faceplate
USB Cable
USB
Type A
USB
Mini-B
USB 1
USB
Ports
PC
_
+
68-2633-50 Rev. B
01 15
MLC 55 Series • Setup Guide (Continued)
3. If required, place the provided spacer against the back of the MLC metal mounting plate, aligning the mounting holes or slots
at the top and bottom of the spacer with those of the metal mounting plate.
NOTE: With all mounting options except the mud-ring, the spacer is required for the faceplate to lie flat against the
mounting surface when attached to the unit. The spacer is not required if you are mounting the MLC 55 RS or the
MLC 55 RS VC to a mud-ring.
4. Place the MLC and the spacer (if applicable) onto the junction box or the mud ring.
5. Secure the unit and spacer (if applicable) to the junction box or mounting bracket using the provided screws in the holes at
the top and bottom of the metal mounting plate.
6. Align the openings in the faceplate with the MLC buttons and place the faceplate onto the mounted unit until its magnets
stick to the metal mounting plate. Adjust the faceplate position until the outer edges of the faceplace are at against the
mounting surface.
4
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Junction
Box
MLC 55 RS
Spacer
Faceplate
RESET
E
VIDEO
VOL
PC
VOL
OFF
ON
DISPLAY
Extron
Mounting to a Junction Box
Wall
2.16"
3.88"
Mud Ring
Mounting to a Mud Ring
DISPLAY
Extron
Faceplate
MLC 55 RS
RESET
E
VIDEO
VOL
PC
VOL
OFF
ON
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron MLC 55 R Manuel utilisateur

Extron
Marque
Extron
Modèle
MLC 55 R
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes