Sea gull lighting 9485-962 Mode d'emploi
- Taper
- Mode d'emploi
WARNING: B E SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED OR THE
C IRCUIT BREAKER OFF.
1. Secure surface mount ring to surface
by marking hole location on surface
and screw surface mount ring to
surface making sure surface mount ring does not
ex out of round.
2. Drill wire exit hole in surface or run wire thru notch in surface moun
t ring.
3. Line up retaining springs on
ture housing with grooves in surface
mount ring and press xture housing into surface mount ring.
1. Drill a 2 3/4” dia. hole in surface.
2. Press
ture housing into
2 3/4” dia. hole.
SURFACE MOUNTING
INSTALLATION AND SAFETY INSTRUCTIONS
HC-207
FOR YOUR SAFETY
RECESS MOUNTING
*
NOT INCLUDED
*
TRIM
1/8”
HOOKS (2)
SLOTS (4)
RETAINING SPRING (2)
SURFACE
MOUNT
RING
SCREWS (2)
GROOVES (2)
HOLES (2)
NOTCH
FIXTURE
HOUSING
*
Lamp
051116
2 3/4”
U.S. PATENT #5,465,199
FIG. 1
FIXTURE
WIRE
WARNING: Use of other manufacturer’s components will void warranty, safety
listing and create a potential safety hazard.
CAUTION: RISK OF FIRE. Must use SeaGull No. 9488 fused plug if use
with transformers over 60w at 12 volts or 100w at 24 volts.
ATTENTION-RISQUE D'INCENDIE MAX 18 WATT TYPE WEDGE T5
CAUTION-RISK OF FIRE MAX 18 WATT TYPE WEDGE T5
(UTILISER SEULEMENT AVEC AMBIANCE CÂBLE 105°)
CAUTION: RISK OF FIRE. Use only 12v lamps with 12v systems. Use
of 12v lamps with 24v system may result in damage to the system
and surrounding area.
ATTENTION : RISQUE D'INCENDIE. UTILISER UNIQUEMENT DES LAMPES 12V
AVEC SYSTÈMES 12V. UTILISATION DE LAMPES DE 12V à 24V SYSTÈME PEUT
ENTRAÎNER DES DOMMAGES AU SYSTÈME ET LA RÉGION AVOISINANTE.
(USE ONLY WITH AMBIANCE 105° CABLE)
fusionnés si utiliser avec des transformateurs de plus de 60w à 12 volts ou
100w à 24 volts.
.SeaGullLighting.com
HC-207
www
WARNING – To reduce the risk of FIRE OR INJURY:
-Lighted lamp is HOT!
-Turn o power and allow to cool before relamping lamp.
-Lamps get HOT quickly! Contact only switch/plug
when turning on.
-Do not touch hot lens, guard, or enclosure.
-Keep lamp away from materials that may burn.
-Do not touch lamp at any time. Use a soft cloth. Oil from
skin may damage lamp.
-Do not operate the luminaire with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
FINAL INSTALLATION AND FUSING HC-207
There are several ways to install the 9485 (disk-lights) using
the 9774, 18w, 12V xenon lamps = (actual consumption 16.2w):
1. When using a 60w max transformer (class II)
you are able to directly
hook up three (3) 9485 to the junction box as in Figure 1.
2. For a run larger than three (3) disk-lights you must use a class I transformer
(larger
than 60w). The following example demonstrates a
run of
eight (8) 9485 disk-lights (8 x 16.2w each = 130w), in this case you
will need to use
a 150w transformer.
60W
J-BOX
9485 (3)
FIGURE 1
150W
TRACK & CABLE
9488 (8) FUSED PLUGS
9485 (8)
FIGURE 2
FUSED PLUG INSTALLATION (NOT INCLUDED)
TRIM INSTALLATION
*
NOT INCLUDED
1. Cut wire to desired length.
2. Split ends of wire about (1/2”) and insert each end of the wire
as far as possible into the plug. Do not strip any insulation o
the wire.
3. Insert contact into one end of plug and press, or use pliers
until contact is
ush with plug. Repeat with other contact
(see illustra tion).
4. Twist wires sideways, insert into notch in plug and twist back
straight.
5. Snap plug on cable.
6. Install lamp (18w max.)(not included).
1. Secure trim (not included) to
housing by inserting
hooks on trim into two of the four slots in
housing and
twist clockwise until trim snaps in place. Bend hooks up
slightly (max. 1/8”) if trim is too hard to turn and lock into
position on housing.
WARNING: Use of other manufacturers components
will void warranty, safety listing and create a
potential safety hazard.
NOTCH
CONTACT
*FUSED
PLUG
9488
*CABLE
*TRACK
FIXTURE WIRE
*FUSED
PLUG
9488
*NOT INCLUDED
-
.
CAUTION: RISK OF FIRE. 12V LAMPS MUST NOT BE USED IN A 24V SYSTEM.
INSTALL CABLE SO THAT CAUTION PRINTED ON CABLE IS VISIBLE AFTER
INSTALLATION AND ATTACH 24V CAUTION LABELS (SUPPLIED WITH THE
24V TRANSFORMER) ON OR ALONG THE TRACK EVERY 4 FT.
ATTENTION : RISQUE D'INCENDIE. LAMPES 12V NE DOIVENT PAS SERVIR À
UN SYSTÈME DE 24V. INSTALLER LE CÂBLE AFIN QUE MISE EN GARDE IMPRIMÉE
SUR CÂBLE EST VISIBLE APRÈS L'INSTALLATION ET ATTACHER DES ÉTIQUETTES
DE MISE EN GARDE DE 24V (FOURNIS AVEC LE TRANSFORMATEUR 24V) SUR OU
LE LONG DE LA PISTE TOUS LES 4 PI.
RISK OF FIRE: DO NOT REMOVE REFLECTOR
RISQUE D'INCENDIE : NE RETIREZ PAS DE RÉFLECTEUR
ATTENTION-RISQUE D'INCENDIE MAX 18 WATT TYPE WEDGE T5
CAUTION-RISK OF FIRE MAX 18 WATT TYPE WEDGE T5
Figure 2 demonstrates fusing each indiviidual disk light, with a 9488 fused pluge
-
1
-
2
