GE current RUL-Series Guide d'installation

RUL-Series
Marque
GE current
Modèle
RUL-Series
Taper
Guide d'installation
Installation Guide
IND408
Lumination® LED Luminaire
Ret Universal Linear Kit
(RUL-Series)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. CAN ICES-005 (A) / NMB-005 (A)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
RISK OF ELECTRIC SHOCK
• Turn power o before inspection, installation or
removal.
• Properly ground electrical enclosure.
• Luminaires wiring and electrical parts may
be damaged when drilling for installation of
LED retrot kit. Check for enclosed wiring and
components.
• LED retrot kit installation requires knowledge
of luminairs electrical systems. If not qualied,
do not attempt installation. Contact qualied
electrician.
• Install this kit only in luminaires that have the
construction features and dimensions shown in
the photographs and/or drawings and where
the input rating of the retrot kit does not
exceed the input rating of the luminaire.
• To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other
sharp objects.
• This retrot kit is accepted as a component
of a luminaire where the suitability of the
combination shall be determined by authorities
having jurisdiction.
RISK OF ELECTRIC SHOCK
• Follow all NEC and local codes.
• Use only Ul approved wire for input/output
connections. Minimum size 18 AWG or 14 AWG
for continuous runs.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le
luminaire.
• Assurez-vous de correctement mettre á la terre le boítier
d’alimentation lectrique.
• Le câblage du luminaire ainsi que ses composantes électriques
peuvent être endommagés lors du perçage requis pour l’installation
de l’ensemble de mise à niveau à DEL. Vériez le câblage et les
composants.
• L’installation de l’ensemble de mise à niveau à DEL requiert des
connaissances en système électrique d’éclairage. Si vous n’avez
pas les qualications adéquates, ne procédez pas à l’installation et
contactez un électricien qualié.
• N’installez cet ensemble de mise à niveau que dans des luminaires
ayant les caractéristiques de construction et les dimensions
indiquées dans les photographies et/ou dessins. La puissance
d’entrée de l’ensemble de mise à niveau ne doit pas excéder la
puissance d’entrée nominale du luminaire dans lequel il est installé.
• An de prévenir tout dommage ou abrasion aux ls électriques,
évitez que ceux-ci ne viennent en contact avec les bordures
métalliques ou d’autres ojets pointus.
• Le nécessaire de modernisation est accepté à titre de composant
d’un luminaire lorsque la pertinence de la combinaison doit être
déterminée par par les autorités compétentes.
RISQUES D’ INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 18 AWG ou 14 AWG pour les rangées
continues.
2
Lumination® (RUL- Series) Installation Guide
Mounting Clips (4) #6-20 Self Drilling Screws (8)
LED Lightbars (2)
Driver (1)
Relamping Label (1)
Installation Guide (1)
Spec (1)
Prior to installation verify that the
kit contains all components below.
Electrical Requirements
The LED luminaire must be connected to the mains
supply according to its ratings on the product label.
Save These Instructions
Use only in the manner intended by the manufacturer. lf you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Components Supplied
Driver Diagram/Electrical Connections
Dim +
Dim –
L
N
LED
Lightbar
LED
Lightbar
LED Driver
1-to-2
0˜10V dim
Grounding Instructions
The grounding and bonding of the overall system
shall be done in accordance to local electric code of
the country where the luminaire is installed.
Model Length (mm) Width (mm) Height (mm) Spacing between tubes (mm)
RUL248A0wwxxLB 559 140 x N 50 140
RUL4880wwxxLB 1118 140 x N 50 140
N = Number of tubes
Luminaire Requirements
The unit covered by this report is intended to retrot: Listed surface mounted uorescent luminaires, or Type Non-IC or type IC recessed
mounted uorescent luminaires; with or without diusers that use, straight 2 or 4 ft tubular lamp(s).
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
IND408 (Rev 04/02/21)
Lumination® (RUL- Series) Installation Guide
Prepare Existing Fixture For Installation
Prior to installation, disconnect all incoming power to xture,
remove all electrical parts and ballast compartment cover
leaving only the supply and grounding leads.
Remove existing hardware (reectors/ballast covers, brackets,
lamps). Save ballast cover for reuse.
1
Fasten Lightbars to Housing
Once lightbars are in desired position permanently secure
them to housing by inserting supplied self-tapping screws
into the endcaps on each end of the lightbar.
3
Installation
Close Lens/Door and Secure Latches
5
IMPORTANT: Only those open holes indicated
in the photographs and/or drawings may be
made or altered as a result of kit installation.
Do not leave any other open holes in an
enclosure of wiring or electrical components.
Fasten self-tapping screws
Attach mounting clips
Attach Mounting Clips
• Snap two mounting clips onto each LED lightbar.
• Bring LED lightbar into housing and reposition the
mounting clips as needed. (For temporary placement of the
lightbar, the mounting clips have magnets located on the
bottom of each clip).
2
4
Optional dimming wires
AC line
Attach Driver To Housing
• Place new driver into housing and secure. Ensure driver is
properly grounded using a serrated grounding screw (not
supplied).
• Connect the power supply lead connectors to the LED
lightbar connectors.
• Replace ballast cover and ax eld-applied label onto
housing.
  • Page 1 1
  • Page 2 2
  • Page 3 3

GE current RUL-Series Guide d'installation

RUL-Series
Marque
GE current
Modèle
RUL-Series
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents