WAC Lighting PD-47821R Mode d'emploi

Marque: WAC Lighting

Modèle: PD-47821R

Taper: Mode d'emploi

Ce manuel convient également à

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47803R/PD-47805R/PD-47809R

 !"#$ %#& #%!%'%(()

• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

• Retain installation instructions for future maintenance reference.

*+,All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could

result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

-Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal

areas clean all external surfaces of the xture once every two weeks with a wet cloth.

-.,+#/# /0#"#12#0#3#4 44)

• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement

avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce

produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

5+Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons

aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec

un chion humide.

6+*+

Plastic Anchor

Qty: 3pcs+1 Extra

Wood Screw

Qty: 3pcs+1 Extra

Wire Connector

Qty: 3pcs+1 Extra

Mounting Screw

Qty: 1 Extra

7()

White - Neutral

Black - Hot Purple - Dim+

Gray or Pink - Dim-

Red - Fixture+

Black - Fixture-

3 5/8"

2 5/8"

-#(%!'289+28:+

Ø11 3/4"

Ø14 7/8"

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47803R/PD-47805R/PD-47809R

Fixture Wires

Black or

Smooth

Fixture Wires

White or

Ribbed

Fixture Wires

Bare wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground)

7();*(

7()<

Instruction:Adjust

the xture wire

length by pushing

the cable gripper on

the canopy and

pulling the wire as

desired.

Driver

Fixture

Canopy

Suspending Line

(MAX 150")

Push up

Cable gripper

Mounting Screw

Wire Connector

Junction Box

Mounting Back Plate

Junction Box Screw

Wood Screw

Plastic Anchor

4CCT Switch

Switch Cover



3000K 2700K4000K

Switch

3500K

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47803R/PD-47805R/PD-47809R

-#(%!'28=+

Ø8 3/4"

Ø7 1/8"

1 3/4" 1 3/8"

++

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

-,67>+?7()<@7()=A

3. Loosen the mounting screw (B) from the xture, and remove the mounting back plate.

4. Drill holes in the wall aligned with the key holes located on the mounting back plate. Insert the plastic anchor (D)

5. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box.

Fasten the mounting back plate to the wall with the plastic anchors using the wood screws (C) provided.

Note: (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue;

(ii) The side of the mounting plate marked “GND” must face out.

6. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.

a) Before securing the canopy in place, it is recommended to retract or extend the wire within the canopy to a desirable length.

b) Due to limited space within the canopy, shorten the cable as necessary to make the installation easier. Make sure to identify and

label all the wiring properly before any trimming/shortening (Fig. 3).

,6*+.?7();@7()=@7()9A

7. Connect the xture, CCT switch, and driver's output wires to center cable as shown in Fig. 3, red to the green,

black to the black, blue to the white, brown to the bare, make sure that wire connectors(A) are secured.

Then tuck them inside the canopy.

8. The lamp can switch between four color temperatures (2700K-3000K-3500K-4000K),

which can be adjusted to your preference with the switch in the canopy (Fig.5).

 the switch comes with a detachable cover, remove the cover prior to adjusting the color temperature,

reattach the cover after adjustment is made.

9. Connect the driver’s input wires to junction box wires as shown in Fig. 2, make sure that all wire connectors(A) are secured.

If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s

ground wire directly to the back plate using the screw provided. After wires are connected, tuck them carefully inside the junction box.

--,*+,7+-?7()A

10. This xture features electronic low voltage (ELV or TRIAC) or 0-10V dimming capabilities. See notes below for specic

dimming wires information.

11. To utilize ELV or TRIAC dimming: use black (hot), white (neutral) and bare copper ground wires (ground).

12. To utilize 0-10V dimming: use purple (dim+), gray or pink (dim-), black (hot), white (neutral) and bare copper ground wires (ground).

NOTE: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.

,6.?7()<A

13. Secure the xture to the mounting back plate using the mounting screw (B). (Fig. 1)

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47803R/PD-47805R/PD-47809R

7()=

*'2:8=+

*'2:89+

*'2:8:+

3000K 2700K4000K

Switch

3500K

DC-DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White - Neutral Black - Hot

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

White - Neutral Black - Hot White - Neutral Black - Hot

3000K 2700K400 0 K

Switch

350 0 K

DC-

DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(900MA)

White - Neutral Black - Hot

Green+

Bare W-

White C-

Green+ White C-

Bare W-

3000K 2700K4000K

Switch

3500K

DC-DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

3000K 2700K4000K

Switch

3500K

DC-DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

3000K 2700K4000K

Switch

3500K

DC-DC+

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

3000K 2700K4000K

Switch

3500K

DC-DC+

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47815R



• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

• Retain installation instructions for future maintenance reference.

All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could

result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal

areas clean all external surfaces of the xture once every two weeks with a wet cloth.



• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement

avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce

produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons

aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec

un chion humide.



Plastic Anchor

Qty: 6pcs+1 Extra

Wood Screw

Qty: 6pcs+1 Extra

Wire Connector

Qty: 3pcs+1 Extra

Mounting Screw

Qty: 1 Extra

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47815R



1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.



3. Loosen the mounting screw (B) from the xture, and remove the mounting back plate.

4. Drill holes in the wall aligned with the key holes located on the mounting back plate. Insert the plastic anchor (D)

5. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box.

Fasten the mounting back plate to the wall with the plastic anchors using the wood screws (C) provided.

Note: (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue;

(ii) The side of the mounting plate marked “GND” must face out.

6. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.

a) Before securing the canopy in place, it is recommended to retract or extend the wire within the canopy to a desirable length.

b) Due to limited space within the canopy, shorten the cable as necessary to make the installation easier. Make sure to identify and

label all the wiring properly before any trimming/shortening (Fig. 3).



7. Connect the xture, CCT switch, and driver's output wires to center cable as shown in Fig. 3, red to the green,

black to the black, blue to the white, brown to the bare, make sure that wire connectors(A) are secured.

Then tuck them inside the canopy.

8. The lamp can switch between four color temperatures (2700K-3000K-3500K-4000K),

which can be adjusted to your preference with the switch in the canopy (Fig.5).

 the switch comes with a detachable cover, remove the cover prior to adjusting the color temperature,

reattach the cover after adjustment is made.

9. Secure the safety cord to the bracket on the mounting back plate to hang the xture temporarily in place and aid installation.

10. Connect the driver’s input wires to junction box wires as shown in Fig. 2, make sure that all wire connectors(A) are secured.

If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s

ground wire directly to the back plate using the screw provided. After wires are connected, tuck them carefully inside the junction box.



11. This xture features electronic low voltage (ELV or TRIAC) or 0-10V dimming capabilities. See notes below for specic

dimming wires information.

12. To utilize ELV or TRIAC dimming: use black (hot), white (neutral) and bare copper ground wires (ground).

13. To utilize 0-10V dimming: use purple (dim+), gray or pink (dim-), black (hot), white (neutral) and bare copper ground wires (ground).

NOTE: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.



14. Secure the xture to the mounting back plate using the mounting screw (B). (Fig. 1)



White - Neutral

Black - Hot Purple - Dim+

Gray or Pink - Dim-

Red - Fixture+

Black - Fixture-

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47815R

Fixture Wires

Black or

Smooth

Fixture Wires

White or

Ribbed

Fixture Wires

Bare wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground)





Instruction:Adjust

the xture wire

length by pushing

the cable gripper on

the canopy and

pulling the wire as

desired.

Driver

Fixture

Canopy

Suspending Line

(MAX 150")

Push up

Cable gripper

Mounting Screw

Wire Connector

Junction Box

Mounting Back Plate

Junction Box Screw

Wood Screw

Plastic Anchor

4CCT Switch

Switch Cover



3000K 2700K4000K

Switch

3500K

20 3/4"



1 3/4" 1 3/8"

Ø20 5/8"

Ø16 3/4"

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47815R



3000K2700K4000K

Switch

3500K

DC-DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

3000K2700K4000K

Switch

3500K

DC-DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White - Neutral Black - Hot

3000K2700K

4000K

Switch

3500K

DC-DC+

White - Neutral Black - Hot

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White - Neutral Black - Hot

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

3000K2700K4000K

Switch

3500K

DC-DC+

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

3000K2700K4000K

Switch

3500K

DC-DC+

Input

Driver

Output

Red Black

Blue

Black

Brown

(1400MA)

White C-

Green+

Bare W-

Green+

Green+ White C-

White C-

Bare W-

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023

dweLED.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION



PD-47815R

• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

• Retain installation instructions for future maintenance reference.

All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could

result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal

areas clean all external surfaces of the xture once every two weeks with a wet cloth.

• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement

avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce

produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons

aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec

un chion humide.



Plastic Anchor

Qty: 6pcs+1 Extra

Wood Screw

Qty: 6pcs+1 Extra

Wire Connector

Qty: 3pcs+1 Extra

Mounting Screw

Qty: 1 Extra