Modern Forms BL-21924 Reflex Mode d'emploi
- Taper
- Mode d'emploi
Modern Forms
www.modern forms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019
1
INSTALLATION INSTRUCTIONS
219-LED Task Lamp
BL-21924
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE
CIRCUIT BREAKER BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code
(NEC) and local regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the
supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not
designated for use with this product by Modern Forms could result in personal injury or property damage, and will void
the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that
customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et
également aux règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour
être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms.
Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages
corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé
ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire.
Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du
luminaire une fois toutes les deux semaines avec un chiffon humide.
HARDWARE
Modern Forms
www.modern forms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019 2
INSTALLATION INSTRUCTIONS
219-LED Task Lamp
BL-21924
Fig.1
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.Be careful not to lose any small parts necessary for
installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screws (B) and back plate from the fixture.
4. Secure the mounting back plate to the junction box using the screw provided with the junction box.
NOTE: The side of the mounting plate marked "GND" must face out.
CONNECTING THE WIRES (Fig. 2)
5. Connect the driver’s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If
your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the
junction box.
6. This lamp features a dimmer switch. Press and release to turn on / off. When fixture is on, press and hold the switch to
cycle from dim to bright and release when desired brightness is reached.
COMPLETING THE INSTALLATION
7. Secure the fixture to the mounting back plate using the mounting screw (B) .
Fig.2Wiring
-
1
-
2
Modern Forms BL-21924 Reflex Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-W28514 Balthus Mode d'emploi
-
-
-
-
-
-
-
-
-