Modern Forms PD-87924 Harmonix Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
PD-87924
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Mounting Screw
Qty:1Extra
A
Wire Connector
Qty:3pcs+1Extra
B
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
PD-87924
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screw (B) and mounting back plate from the xture.
4. Secure the mounting back plate to the junction box using standard
junction box screws that comes with the junction box. Note: the side
of the mounting plate marked “GND” must face out.
5. Adjust the xture wire length by pushing the cable gripper on the canopy
and pulling the wire as desired. Make sure the wires are the same length.
a. Retract these wires close to a desirable length to within the canopy
before securing the xture in place. Using the cable gripper to adjust
more than 18” of wire length is not desirable.
b. Warning: Shortening these cables without professional helps or electronic
background is not advisable. Any modications to the xture will result in
voiding the warranty of the product.
6. Hook the safety cord to the mounting back plate slot.
7. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Please follow these if shortening the wire is needed. Take note or take picture of how the wires are being connected and label each wire clearly.
Using the Fig. 4 as given below as reference.
9. Secure the xture to the mounting back plate using the mounting screw (B) .
10. This xture features electronic low voltage (ELV) or 0-10V dimming capabilities.
See notes below for specic dimming wires information.
11. To utilize ELV dimming: use wires black (hot), white (neutral) and bare copper
ground wire (ground).
12. To utilize 0-10V dimming: use wire purple (dim+), pink or gray (dim-), black (hot),
white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the xture in order to
allow the 0-10V dimming to function properly.
Ø31
2"
Ø23
4"
Ø71
2"
Cord
Safety cord
Mounting Backplate
Junction box
Driver input wire
Canopy
A
Wire connector
Fixture
Mounting screw
B
Driver(2pcs)
LD-700MA35U-DIM-IS
Push up
Cable-gripper
Junction box screw
Ground wire
Purple - Dim+
Pink or Gray - Dim-
Red - Fixture+
Black - Fixture-
Black - Hot
White - Neutral
3
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
PD-87924
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Driver
Input
Output
Black(L)
White(N)
Black(-)Red(+)
I
nput
Output
Black(L)
White(N)
Black(L)
White(N)
Black(-)Red(+)
Driver
+ -
+-+-
+ -
-
1
-
2
-
3
Modern Forms PD-87924 Harmonix Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-43728 Metric Mode d'emploi
-
-
-
-
-
-
-
-
-