Genie ACSCTG-UNIV2 Universal Garage Door Opener Remote Mode d'emploi

Marque: Genie

Modèle: ACSCTG-UNIV2 Universal Garage Door Opener Remote

Catégorie: Porte de garage

Taper: Mode d'emploi

XXXXX.00XXX - PR4, 02/2021

UNIVERSAL 2-BUTTON REMOTE

INSTRUCTIONS

WARNING

MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.

•DO NOT install transmitter unless the door operator’s safety device works as required by the

door operator’s manual.

• Wall Console must be mounted in sight of door, at least 5 feet above oor and clear of moving

door parts.

•Keep people clear of opening while door is moving.

•DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

•Close door then disconnect opener using the manual release handle.

•DO NOT use transmitter or door operator.

• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

NOT FOR USE WITH ANY GARAGE DOOR OPENER MANUFACTURED PRIOR TO 1993.

SAFETY BEAMS (PHOTOCELLS) MUST BE IN PLACE AND OPERATIONAL.

AVERTISSEMENT

UNE PORTE EN MOUVEMENT PEUT CAUSER DE GRAVES

BLESSURES, VOIRE LA MORT.

• N’installez PAS le transmetteur à moins que l’appareil de sécurité du dispositif de fermeture de

porte ne fonctionne conformément au manuel du dispositif de fermeture de porte. La console

murale doit être montée à la vue de la porte, à au moins 5 pieds au-dessus du sol et il ne doit y

avoir aucune pièce de porte en mouvement à proximité.

• Éloignez les gens de l’ouverture lorsque la porte est en mouvement.

• NE permettez PAS aux enfants de jouer avec le transmetteur ou le dispositif de fermeture de

porte.

• Si l’inversion de sécurité ne fonctionne pas correctement :

• Fermez la porte, puis déconnectez le dispositif d’ouverture à l’aide de la poignée de dégagement

manuel.

• N’utilisez PAS le transmetteur ni le dispositif de fermeture de porte.

• Référez-vous aux manuels du propriétaire de la porte et de l’ouvre-porte avant de tenter toute

réparation.

THINGS TO KNOW BEFORE STARTING:

• During programming, the garage door opener may operate. Ensure that the

garage door opening is clear of personnel or any obstructions.

• Do not to press the LEARN button for longer than the noted 2-3 seconds as it

could cause your existing, operational remotes and keypads to no longer work.

• All buttons are factory set to Genie Intellicode® 1.

Below are the brands and specications that this remote is compatible with. Find the

ID# in Chart A below that references your specic opener specication. You will need

this number during programming. Refer to STEP 1 to nd the type and/or LEARN/

PROGRAM button.

NOTE: During programming, the garage door opener will operate. Ensure that

the garage door opening is clear of personnel or any obstructions.

Chart A

Genie® and Intellicode® are registered trademarks of The Genie Company. All other listed names and trademarks

are the property of their respective owners.

STEP 1 - Find Specications & Learn Button

1. Locate the brand and opener/receiver specications for your device by consulting the label on the

opener/receiver, the instruction manual, the current remote controls for the opener, or the original

manufacturer of the opener/receiver.

2. Find the LEARN/PROG button on your device - shape, color or name of this button could vary by

brand. For garage door openers, be sure to check under the light covers. For commercial or gate

openers, this button may be on the circuit board of the opener. In some cases, this button could

also be on an external receiver that is mounted on or nearby the product. Consult the devices

manual if needed.

Activation Tab: Pull tab to activate the remote.

STEP 2 - Activate Remote/Button Layout & LED

LED - The LED will light with each button press and will also light

in response to button presses during dierent programming

modes.

PRGM

SET

RADIO

SIGNAL

LEARN

CODE

LEARN

Gate

Receivers

EXAMPLES:

*For Marantec® openers, reference operator manual to program remotes to the operator head.

FCC Part 15.21 Statement:

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

FCC / IC Statement:

This device complies with FCC Part 15 and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation of the device.

Programming Assistance:

If the opener does not activate after the steps shown, repeat steps or

contact Customer Care by website chat (www.geniecompany.com)

or by phone at: 1-800-354-3643 for programming assistance.

You may also scan this QR code for additional information and links.

STEP 3 - Programming Remote

IMPORTANT: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button -

move immediately to the proper section below. For all other ID#s, proceed to LEARN

METHOD section.

LEARN METHOD

Review Chart A to nd your specications and available programming options. Each

button can be programmed individually to operate up to 2 dierent brands of garage

door openers and gate receivers.

1. Remove activation tab from inside battery compartment.

2. Find and remember the required number of button presses (ID#) in the LEARN

METHOD column next to your brands/specication in Chart A.

REMEMBER: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button

ONLY - Move immediately to instructions below. For all other ID#s, proceed to step 3.

3. On remote, press and hold down BOTH buttons at the same time – as soon as the

RED LED begins ashing, immediately release both buttons (@ 5 seconds).

4. On remote, press button of your choice the required number of times from CHART

5. When presses are complete, simply wait until the GREEN LED blinks and then goes

out.

6. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.

7. Press and release button you just programmed once every 2 seconds until the

garage door opener operates.

8. Test the button - programming is complete.

TIP: Allow the LED light on the universal transmitter to stop ashing before your next

button press.

ONLY for ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn:

1. Remove activation tab from inside battery compartment.

2. On remote, press and hold down BOTH buttons at the same time – as soon as the

RED LED begins ashing, immediately release both buttons (@ 5 seconds).

3. On remote, press button of your choice four times.

4. When presses are complete, simply wait until the GREEN LED blinks and then goes

out.

5. On remote, press and hold down the button you just chose until the GREEN LED

blinks and goes out again – then release (@5 seconds).

6. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.

7. Press the remote button you chose ONE time. Opener will click.

8. On the opener, press the LEARN/PROGRAM button again for 2-3 seconds then

release.

9. Press the remote button you chose ONE time again. Opener will click again.

10. Press the remote button again and the opener will activate.

11. Test the button - programming is complete.

TIP: Allow the LED light on the universal remote to stop ashing before your next

button press.

Clearing Remote

Clearing out the remote

To clear any existing programming from the remote, perform the following:

1. Press and hold down BOTH buttons at the same time – continue holding down

both buttons until the GREEN LED blinks and goes out (@10 seconds).

Installing Visor Clip - Changing Batteries

Remove visor clip and screw from back of remote.

Pry case open with small coin or screwdriver.

Replace battery with CR2032 coin cell.

Insert visor clip to any of the 4 slots in back of case dependent on

mounting preference.

AVAILABLE PROGRAM METHOD LEARN METHOD ID#

Brand Name Specication Notes Number of

Button Presses (ID#)

Genie® 315/390 MHz, Intellicode® I, 1995-current 1

Overhead Door® 315/390 MHz, CodeDodger® I, 1995-current 1

Chamberlain®

LiftMaster®

CraftsMan®

Purple Learn Button, Security +®, 2006-2014, 315 MHz 2

Orange/Red Learn Button, Security +®, 1996-2005, 390 MHz 3

Yellow Learn Button, Security +2.0®, 2011-current, 390 MHz 4

Green Learn Button, Billion Code®, 1993-1995, 390 MHz 5

Genie® 315/390 MHz, Intellicode® II, 2010-2011 6

Overhead Door® 315/390 MHz, CodeDodger® II, 2010-2011 6

Sommer® 310 MHz, Rolling Code 7

Linear® 318 MHz, Mega Code® 8

Wayne Dalton® 372.5 MHz, Rolling Code, 1999-current 9

Ryobi® 372.5 MHz, Rolling Code 10

Guardian® 303 MHz, Fixed Learn Code 11

Xtreme® brand 303 MHz, Fixed Learn Code 11

Marantec® 315 MHz, Fixed Learn Code 12

FAAC® 433.92 MHz, Rolling Code 13

Visor Clip

Change Battery

Genie ACSCTG-UNIV2 Universal Garage Door Opener Remote Mode d'emploi

Marque: Genie

Modèle: ACSCTG-UNIV2 Universal Garage Door Opener Remote

Catégorie: Porte de garage

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Genie ACSCTG-UNIV2 Universal Garage Door Opener Remote Operating instructions

Documents connexes

Genie ACSCTG 2-Button Universal Remote Mode d'emploi

Genie ACSCTG-UNIV2 Universal Garage Door Opener Remote Mode d'emploi

Genie ACSCTG-UNIV2 Universal Garage Door Opener Remote Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents