resideo RTH9585WF Smart Series Manuel utilisateur

User Guide

Read and save these

instructions.

For help please visit

resideo.com

RTH9585WF

Smart Series

M37768

72

Find rebates: resideo.com

Color Touchscreen

Programmable

Thermostat

In the box you will find

• Thermostat

• Wallplate

• Screws and anchors

• Quick Start Guide

• Thermostat ID Card

• Wire labels

• User Guide

• C-wire addendum

69-2715EF—07 ii

Welcome

Congratulations on your purchase of a color touchscreen programmable thermostat. When

registered to Total Connect Comfort, you can remotely monitor and control the heating and

cooling system in your home or business—you can stay connected to your comfort system

wherever you go.

Total Connect Comfort is the perfect solution if you travel frequently, own a vacation home,

a business, or manage an investment property or if you are simply looking for peace of

mind.

This thermostat works with common 24 volt systems such as forced air, hydronic,

heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas

fireplace, or with 120/240 volt systems such as baseboard electric heat.

MERCURY NOTICE: If this product is replacing a control that contains mercury in a

sealed tube, do not place the old control in the trash. Contact your local waste

management authority for instructions regarding recycling and proper

disposal.

NOTICE: To avoid possible compressor damage, do not run air conditioner if the

outside temperature drops below 50°F (10°C).

CAUTION: ELECTRONIC WASTE NOTICE

The product should not be disposed of with other household waste. Check for

the nearest authorized collection centers or authorized recyclers. The correct

disposal of end-of-life equipment will help prevent negative consequences

for the environment and human health.

Need help?

Visit resideo.com or call 18006333991 for assistance before returning the thermostat to

the store.

1 69-2715EF—07

About your new thermostat

Home screen quick reference ...................... 2

Business screen quick reference ...............3

Installation

Installing your thermostat ..........................14

Connecting to your WiFi network ..........15

Registering your thermostat online ....... 18

Operation

Setting the time/date ....................................19

Setting the fan .................................................. 19

Setting system mode ....................................20

Preset energy-saving schedules .............20

Adjusting program schedules ...................21

Overriding schedules–home ..................... 22

Overriding schedules–business ..............22

Viewing equipment status ..........................23

Setting vacation hold–home ..................... 23

Setting holiday/event schedules–

business ............................................................24

Setting custom events–business ...........25

Setting holiday schedule–business.......25

Setting holiday override–business ......... 26

Initiating occupancy mode–business .......26

Customizing screen color ...........................27

Setting preferences ........................................27

Cleaning the thermostat screen ..............28

Adjusting security settings .........................28

Software updates ............................................29

Unregistering your thermostat ................. 29

Smart Response Technology ....................30

Pre-occupancy purge....................................31

Compressor protection.................................31

Auto changeover ..............................................31

Setting advanced preferences .................34

Changing system setup ............................... 35

Appendices

Frequently asked questions .......................36

Getting help and responding to

alerts ...................................................................37

Troubleshooting ...............................................38

Limited warranty ..............................................41

Table of contents

With your new thermostat, you can:

• Connect to the Internet to monitor and control your heating/cooling system.

• View and change your heating/cooling system settings.

• View and set temperature and schedules.

• Receive alerts via email and get automatic upgrades.

• View outdoor temperature and humidity (requires WiFi set up and registration).

Features of your thermostat

69-2715EF—07 2

Quick reference: home use

FAN. Select fan mode.

HOME. Touch to

display Home screen.

Current time.

Outdoor conditions.

Outdoor temperature

and humidity appear

after registration.

Current status.

Shows system mode

(heat/cool).

MODE. Select system mode

(heat, cool, auto, em heat).

SETTINGS. Touch to

display options. Start here

to set a program schedule.

Current setting. Change

temperature setting

and select temporary or

permanent hold.

Indoor conditions. Shows

indoor temperature and

humidity.

3 69-2715EF—07

Quick reference: business use

FAN. Select fan mode.

HOME. Touch to

display Home screen.

Current time.

Outdoor conditions.

Outdoor temperature

and humidity appear

after registration.

Current status.

Shows system mode

(heat/cool).

Override. Touch to

temporarily override

the program schedule.

MODE. Select system mode

(heat, cool, auto, em heat).

SETTINGS. Touch to

display options. Start here

to set a program schedule.

Thermostat location.

Quickly identify which

thermostat is in control of a

specific area.

Current setting. Change

temperature setting

and select temporary or

permanent hold.

Indoor conditions. Shows

indoor temperature and

humidity.

69-2715EF—07 4

Setting up your thermostat

Setting up your programmable touchscreen thermostat is easy. It is preprogrammed and

ready to go as soon as it is installed and registered.

Install your thermostat.

Connect it to your home wireless network.

Register online for remote access.

Before you begin, you may want to watch a

brief installation video.

Use the QR Code® at the front of this guide, or go to

resideo.com

2

3

1

5 69-2715EF—07

Installing your thermostat

You might need the following tools to install this thermostat:

• No. 2 Phillips

screwdriver

• Pen

• Pencil

• Level (optional)

• Drill and bits

(3/16” for drywall,

7/32” for plaster)

(optional)

• Hammer (optional)

• Electrical tape

(optional)

1 Switch OFF power to your

heating/cooling system.

Important! To protect your equipment, switch

OFF the power to your heating/cooling system

at the breaker box or the system switch.

or

M31535

Circuit breaker

box

Heating/

cooling system

power switch

C

M33823A

If you have an older thermostat with a

sealed mercury tube, turn to page ii for

proper disposal instructions.

Terminal designation

2 Remove old thermostat faceplate and leave

wires connected.

2a Take a picture of the wire

connections for later reference.

Note: You will need a

picture of your wire

connections to wire the

new thermostat.

69-2715EF—07 6

Installing your thermostat

3 Label the wires.

Use the supplied sticky tags to label

each wire as you disconnect it. Label

wires according to the old thermostat

terminal designations, not by wire color.

Note: If no tag matches a terminal

designation, write the appropriate

letter on a blank sticky tag.

Blank tags

Sticky tag

Terminal

designation

C

MCR31537

7 69-2715EF—07

Note: Wrap the wires around a pencil

to prevent them from falling back into

the wall.

LEVEL

HERE

R

Y

C

W

G

MCR34499

C

K

Rc

R

W-

O/B

Y

G

W2-

Aux/E

Y2

L

4 Mount wallplate for thermostat.

Mount your new wallplate using

screws and anchors included with

the thermostat.

If necessary:

Drill 3/16-in holes for drywall.

Drill 7/32-in holes for plaster.

Note: You may be able to use your

existing wall anchors. Hold the

wallplate up to the existing anchors to

check for alignment. Wallplate

Important! This thermostat requires a C, or common, wire for power. The C, or common, wire

brings 24 VAC power to the thermostat. If you are replacing an existing thermostat, it might

not have a C wire connected to it. Many older mechanical or battery operated thermostats do

not require a C wire. See the C Wire Addendum document included in this package for more

information.

Note: Not all heating/cooling systems label the 24 VAC common C. Check your system

manual or contact the manufacturer to find out which terminal is the 24 VAC common.

View the Alternate Wiring videos at resideo.com

Wiring

For conventional heating/cooling systems (natural gas, oil or electric furnace, air

conditioner), see page 8. See “Glossary” on page 39 for further definition.

For a heat pump system, see page 9. See “Glossary” on page 39 for further

definition.

Installing your thermostat

69-2715EF—07 8

Wiring (Conventional System)

6A Wire the thermostat to your

conventional system.

a Starting with the C Wire, match the sticky tag

on the wire to the terminal labels.

You must have a C wire.

b

Straighten wire and gently slide

into terminal

hole until it clicks into place. (If you need to

remove a wire, use a pen tip to press the

terminal release and then pull wire out.)

Note: Refer to the wiring picture you took

in Step 2.

Tip: To make it easier to slide the wire into place,

use a pen tip to hold down the terminal release.

MCR34540

C

K

Rc

R

W-

O/B

Y

G

W2-

Aux/E

Y2

L

W

Y

G

R

C

Labels don’t match?

See alternate wiring

keys on page 11 -

page 12.

Terminal release

Remove jumper loop ONLY if

you have both R and Rc wires.

EXAMPLE WIRING

Yours may look different

Note: The wiring for your application might

be different than the wiring shown below.

9 69-2715EF—07

Installing your thermostat

Wiring (Conventional System continued)

c In the image on the right, check the

box next to each connection. You will

use this checklist in Step 9.

d Verify wire is firmly secured by gently

pulling on wire.

e Repeat steps a–d for all other wires.

f Push any excess wire back into the

wall opening after all wires are

installed.

g Continue to page 12.

Important!

Check the box for each wire

you connect. You will need this

information in Step 9.

C

K

Rc

R

W-O/B

Y

G

W2-

Aux/E

Y2

L

Wiring (Heat Pump System)

6B Wire thermostat to your heat pump.

a Starting with the C Wire, match the sticky tag on

the wire to the terminal labels.

You must have a C wire. See page 8.

b Slide wire gently into terminal hole

until it clicks into place. (If you need

to remove a wire, use a pen tip to

press the terminal release and then

pull the wire out.)

Note: Refer to the wiring picture you took

in Step 2.

Tip: To make it easier to slide the wire into place,

use a pen tip to hold down the terminal release.

Note: The wiring for your application might

be different than the wiring shown below.

MCR34566

C

K

Rc

R

W-

O/B

Y

G

W2-

Aux/E

Y2

L

O

Y

G

R

C

AUX

Labels don’t match?

See alternate wiring keys on

page 11 - page 12..

Terminal release

Remove jumper loop ONLY if

you have both R and Rc wires.

EXAMPLE WIRING

Yours may look different

69-2715EF—07 10

Installing your thermostat

Wiring (Heat Pump System continued)

c In the image on the right, check the box next to

each connection. You will use this checklist in

Step 9.

d Verify wire is firmly secured by gently

pulling on wire.

e Repeat steps a–d for all other wires.

Note: If old thermostat has separate wires on

AUX and E, use a wire nut to attach both wires to a

separate wire. Slide this third wire into the

W2Aux/E terminal.

f Push any excess wire back into the wall opening

after all wires are installed.

g Continue to page 11.

Labels don’t match?

See alternate wiring

keys on page 11 -

page 12.

Important!

Check the box for each wire

you connect. You will need

this information in Step 9.

C

K

Rc

R

W-O/B

Y

G

W2-

Aux/E

Y2

L

11 69-2715EF—07

Alternate wiring (Conventional

System)

Use this if your wire labels

don’t match the terminal labels.

Note: You must have a C wire

or equivalent. See page 8.

Alternate wiring key

(Conventional System)

1• If you have both an R and Rc wire, unplug the jumper loop by pulling on the wire

loop.

• If your old thermostat had both R and RH wires, connect the R wire to the Rc

terminal, the RH wire to the R terminal, and unplug the jumper loop.

MCR36751

C

R

W

Y

G

1

C

K

Rc

R

W-

O/B

Y

G

W2-

Aux/

E

Y2

L

W1

W2

Y2

RH 4V

Rc

R

C1 XB

Installing your thermostat

Alternate wiring

(Heat Pump System)

Use this if your wire labels don’t

match the terminal labels.

Note: You must have a C wire

or equivalent. See page 8.

MCR36752

C

R

O

Y

G

2

C

K

Rc

R

W-

O/B

Y

G

W2-

Aux/E

Y2

L

3

4

5

AUX

XX2

Y2

1

B

6

XB

Rc

R

VVR

1

L

F

WW1W2

69-2715EF—07 12

Alternate wiring key (Heat Pump System)

Thermostat

Wallplate

LEVEL

HERE

M34498A

If you have both an R and Rc wire, unplug the jumper loop by pulling on the wire loop.

If your old thermostat had both R and RH wires, connect the R wire to the Rc terminal,

the RH wire to the R terminal, and unplug the jumper loop.

If your old thermostat had both V and VR wires, check

resideo.com for help.

If your old thermostat had separate O and B wires, and is controlling a single zone

heat pump system, attach the B wire to the C. If there is more than one thermostat

controlling the system, call Resideo zoning at 8006333991 for wiring assistance.

If your old thermostat had separate Y1, W1, and W2 wires, check resideo.com for help.

If the old thermostat has separate wires on Aux and E, use a wire nut to attach both

wires to a separate wire. Slide this third wire into the W2Aux/E terminal.

This is the system monitor. If the monitor finds a problem, you will see an orange alert

button on the thermostat home screen.

2

1

4

6

3

5

7 Attach thermostat to wallplate.

Align the thermostat with the wallplate

and then snap into place.

13 69-2715EF—07

Installing your thermostat

8 Switch heating/cooling system ON.

Important!

8a Verify that the C wire is connected at the

thermostat and at the heating/cooling system.

8b Make sure the heating/cooling system door is

firmly secured.

8c Switch power back ON for your heating/cooling

system at the breaker box or its power switch.

M31544

or

Circuit breaker

box

Heating/

cooling system

power switch

Before connecting to your WiFi network, you need to set initial

thermostat options to define your heating/cooling system:

• Language

• Home or business

You can customize other options later.

9 Follow prompts on the screen to select

appropriate options.

9a Touch the language you want the

thermostat to display, then touch Next.

9b Select Home or Business installation, then touch Next.

9c Touch Next, or name the thermostat location—touch

THERMOSTAT and follow the rest of the instructions.

9d Select what type of heating and cooling equipment your

thermostat will control and touch Next.

Note: Touch the orange Help button on any screen for more

information.

69-2715EF—07 14

Installing your thermostat

9e Select your system type and touch Next. The

system type determines other selections for

completing initial setup. Use the checklist from

Step 6A-d when making selections.

9f Touch Next after making selections on each

screen.

9g Touch Done on the last screen. The thermostat

displays an option to connect to your WiFi

network.

Note: Touch the orange Help button on any screen for

more information.

After touching

Done

on the final screen of the initial set

up, the thermostat displays an option to connect to

your WiFi network.

1 Connect the WiFi network.

Touch Yes to connect the thermostat to your WiFi

network. The screen displays the message “Searching

for wireless networks. Please wait...” after which it

displays a list of all WiFi networks it can find.

Note: If you cannot complete this step now, touch

I’ll

do it later

. The thermostat will display the home screen.

Complete this process by selecting

SETTINGS

>

WiFi Setup

.

Continue with Step 2.

2 Select the network.

2a Touch the name of the network you

want to use. The thermostat displays a

password page.

Ye s

Your Network

Note: If your home network is not

shown on the list, touch

Rescan

.

15 69-2715EF—07

2b Using the keyboard, touch the characters that

spell out your home network password.

2c Touch Done. The thermostat displays “Connecting

to your network. Please wait...” then shows a

“Connection Successful” screen.

2d Touch OK to display the registration information

screen.

2e Note your Thermostat MAC and Thermostat CRC.

You need these numbers to complete online

registration.

Done

OK

Connecting to your WiFi network

To register your thermostat, follow the instructions

beginning on page 18.

Note: The Register Online screen remains active until

you complete registration and/or touch Done.

Note: If you touch Done before you register online, your

home screen displays an orange alert button telling you

to register. Touching that button displays registration

information and an option to snooze the task.

Done

Register online

for remote

access

69-2715EF—07 16

Reconnecting your WiFi network

1 Touch SETTINGS.

2 Select WiFi Setup.

3 Touch the name of the network you want to use. The

thermostat may display a password page.

4 To enter a password, touch characters to spell out

your home network password, then touch Done.

5 The thermostat displays “Connecting to your

network. Please wait...” then a “Connection

Successful” screen.

6 Touch Next.

• If your thermostat is registered, you will see your

signal strength and other status information.

Touch Done.

• If the screen displays “Register Online for Remote

Access,” follow instructions on page 18.

SETTINGS

Wi-Fi Setup

Disconnecting your WiFi network

1 Touch SETTINGS.

2 Select WiFi Setup.

3 Touch Disconnect from Network. The thermostat will

display a question to confirm your selection.

4 Touch Yes to confirm that you want to disconnect

from the network. The thermostat will display the

WiFi Setup screen.

5 Touch OK to display the menu.

SETTINGS

Wi-Fi Setup

Disconnect from Network

OK

17 69-2715EF—07

M31570

To view and set your thermostat remotely,

you must have a Total Connect Comfort

account. Use the following steps.

1 Open the Total Connect Comfort web

site.

Go to mytotalconnectcomfort.com

View the Thermostat

Registration video at

resideo.com

Registering your thermostat online

2 Login or create an account.

If you have an account,

click Login

– or –

click Create An Account

2a Follow the instructions on the screen.

2b Check your email for an activation message

from My Total Connect Comfort. This may take

several minutes.

Note: If you do not receive a response, check your

junk mailbox or use an alternate e-mail address.

2c Follow activation instructions in the email.

2d Log in.

69-2715EF—07 18

Registering your thermostat

online

3 Register your thermostat.

After you are logged in to your Total

Connect Comfort account, register your

thermostat.

3a Follow the instructions on the screen.

After adding your thermostat location,

you must enter the thermostat’s unique

identifiers:

• MAC ID

• MAC CRC

Note: These IDs are listed on the Register

Online screen or on the Thermostat ID Card

included in the thermostat package. The IDs

are not case sensitive.

Home logo is used under license from Honeywell International Inc.

Printed in U.S.A.

Resideo Inc., 1985 Douglas Drive North,

Golden Valley, MN 55422

69-2723EFS-03

Thermostat ID Card

Use the MAC ID and CRC ID to register

this product at mytotalconnectcomfort.com

Carte d’identiﬁcation de thermostat

Utilisez l’identiﬁcation MAC et l’identiﬁcation CRC pour enregistrer

ce produit à mytotalconnectcomfort.com

Tarjeta de identiﬁcación del termostato

Utilice la identiﬁcación MAC y la identiﬁcación CRC para inscribir este

producto en mytotalconnectcomfort.com

ww

w

.r

es

i

deo

.

com

MAC ID MAC CRC

When the thermostat is successfully

registered, the Total Connect Comfort

registration screen will display a SUCCESS

message.

You can now control your thermostat from

anywhere through your laptop, tablet, or

smartphone.

°

72

GET IT ON

Total Connect Comfort free app is

available for Apple® iPhone®, iPad® and

iPod touch® devices at iTunes® or at

Google Play® for all Android™ devices.

La page charge ...

resideo RTH9585WF Smart Series Manuel utilisateur

Ce manuel convient également à

resideo RTH9585WF Smart Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents