Hitachi C 10FCE2 Le manuel du propriétaire

Marque: Hitachi

Modèle: C 10FCE2

Catégorie: Scies à onglet

Taper: Le manuel du propriétaire

Ce manuel convient également à

Compound Miter Saw

Kapp-und Gehrungssäge

Scie à onglets

Sega circolare orientabile

Afkort en paneelzaagmachine

Ingletadora

Serra de esquadria

C 10FCH2 • C 10FCE2

Handling instructions

Bedienungsanleitung

Mode d’emploi

Instruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste instruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

001Cover_C10FCH2_WE_7L 3/11/09, 9:491

T O

U U

00Table_C10FCH2_WE_7L 3/11/09, 9:521

10 11

12 13

16 17

1514

[

A0c

00Table_C10FCH2_WE_7L 3/11/09, 9:522

22 23

25 v

\ {

n o

[ q

00Table_C10FCH2_WE_7L 3/11/09, 9:523

26 27

28 29

30 31

6 mm

17 mm

•

ç£

†¢

J§

}

†

00Table_C10FCH2_WE_7L 3/11/09, 9:524

English Deutsch Français

1Handle Griff Poignée

2Lock lever (C) Sperrhebel (C) Levier de verrouillage (C)

3Motor Head Motorkopf Tête de moteur

4Gear Case Getriebegehäuse Réducteur

5Dust Bag Staubbeutel

Bacquet de réception des copeaux

6Laser Marker (Only C10FCH2) Lasermarkierer (Nur C10FCH2) Marqueur à laser

(C10FCH2 seulement)

7Turn Plate Drehplatte Plaque tournante

86 mm Wing Bolt 6 mm-Flügelschraub Boulon à ailettes de 6 mm

9Vise Assembly Schraubstocksatz Ensemble d’étau

:Sub Fence (B) Hilfsführung (B) Guide auxiliaire (B)

AFence (B) Gitter (B) Guide (B)

BTurntable Drehbühne Plaque tournante

CSide Handle Seitengriff Poignée latérale

DLever Hebel Levier

EIndicator (A) (For miter scale) Zeiger (A) (Für Gehrungsskala)

Indicateur (A) (Pour l'échelle d'onglet)

FTable Insert Tischeinsatz Plaque d’insertion

GFence (A) Gitter (A) Guide (A)

HIndicator (B) Anzeiger (B) Indicateur (B)

(For bevel scale) (Für Schrägschnittsskala) (pour échelle de biseau)

ILower Guard Unterer Schutz Guide inférieur

JSaw Blade Sägeblatt Lame de scie

KMotor Motor Moteur

LNameplate Typenschild Plaque signalétique

MTrigger Switch Auslöserschalter Interrupteur à détente

NSwitch (For laser marker) Schalter (Für Lasermarkierer) Interrupteur (Pour marqueur à laser)

(Only C10FCH2) (Nur C10FCH2) (C10FCH2 seulement)

OBase Grundplatte Socle

PHolder (B) Halter (B) Support (B)

QClamp Lever Klemmhebel Levier de serrage

RLocking Pin Verriegelungsstift Goupille de verrouillage

SDuct Kanal Conduit

TRight Angle Rechter Winkel Angle droit

ULine Linie Ligne

VWarning Sign Warnsymbol Signe d’avertissement

W6 mm Bolt 6 mm-Schraube Boulon 6 mm

XM6 × 20 Screw M6 × 20 Schraube Vis M6 × 20

YScrew Holder Schraubenhalter Support de vis

Z6 mm Wing Bolt (B) 6 mm-Flügelschraub (B) Boulon à ailettes de 6 mm (B)

[Vise Shaft Schraubstockachse Arbre de l’étau

\6 mm Wing Bolt (A) 6 mm-Flügelschraub (A) Boulon à ailettes de 6 mm (A)

]Workpiece Werkstück Pièce

`Vise Plate Schraubstockbacke Talon

aKnob Knopf Bouton

bM6 Flat screw M6 Flache Schraube Vis à tête plate M6

cPlate (A) Platte (A) Plaque (A)

dM6 Nylon nut M6 Nylon-Mutter Écrou en nylon M6

eM10 Bolt M10 Schraube Boulon M10

00Table_C10FCH2_WE_7L 3/11/09, 9:525

English Deutsch Français

fLaser line Laserlinie Raie laser

gGroove Nut Rainure

h4 mm Hex. Bar Wrench 4 mm-Sechskantschlüssel Clé à tige hexagonale de 4 mm

iMarking (pre-marked) Markierung (vor-gekennzeichnet) Marquage (pré-marqué)

jMiter Scale Gehrungsskala Echelle d'onglet

kHolder (Optional accessory) Halter (Sonderzubehör) Support (Accessoire en option)

lSteel Square Stahlwinkel Equerre en acier

6 mm Wing Nut (Optional accessory)

Flügelschraube, 6 mm Ecrou à ailettes de 6 mm

(Sonderzubehör) (Accessoire en option)

nHeight Adjustment Bolt 6 mm Höheneinstellschraube, 6 mm Boulon de réglage de la hauteur

(Optional accessory) (Sonderzubehör) de 6 mm (Accessoire en option)

oBase Surface Grundfläche Surface du socle

p6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

(Optional accessory) (Sonderzubehör) (Accessoire en option)

qStopper (Optional accessory) Anschlag (Sonderzubehör) Butée (Accessoire en option)

r6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

(Optional accessory) (Sonderzubehör) (Accessoire en option)

s6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

Crown Molding Vise Ass’y Schraubstocksatz für Ensemble d'étau de corniche à

t(Optional accessory) Kronenform (Sonderzubehör) courbe complexe

(Accessoire en option)

u6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

v6 mm Wing Bolt 6 mm-Flügelschraube Boulon à ailettes de 6 mm

wCrown Molding Stopper (L) Kronenformanschlag (L) Butée de corniche à courbe

(Optional accessory) (Sonderzubehör) complexe (L) (Accessoire en option)

xCrown Molding Stopper (R) Kronenformanschlag (R) Butée de corniche à courbe

(Optional accessory) (Sonderzubehör) complexe (R) (Accessoire en option)

y6 mm Knob Bolt 6 mm-Knopfschraube Vis moletée de 6 mm

zKnob Knopf Bouton

{Crown molding Kronenform Corniche à courbe complexe

|4 mm Machine Screw 4 mm-Maschinenschraube Vis à métaux de 4 mm

}Spindle Cover Spindelabdeckung Couvercle de l’arbre

~Spindle Lock Spindelhebel Verrou en fuseau

å10 mm Box Wrench 10 mm Steckschüssel Clé à écrous de 10 mm

çWasher (B) Unterlegscheibe (B) Rondelle (B)

†Bolt Schraube Boulon

¢Washer Unterlegscheibe Rondelle

£Washer (A) Unterlegscheibe (A) Rondelle (A)

§Color (A) Farbe (A) Couleur (A)

•Hex. Head Bolt Sechskantschraube Boulon à tête hexagonale

¶Steel Square Stahlwinkel Equerre en acier

ßWear limit line Verschleißgrenze Repère de limite d’usure

®Groove for Driver Aussparung für Schraubendreher Rainure pour clé à écrous

©Brush Cap Bürstenkappe Bouchon de carbone

00Table_C10FCH2_WE_7L 3/11/09, 9:526

Italiano Nederlands Español

1Manico Greep Empuñadura

2Leva di blocco (C) Vergrendelgreep (C) Palanca de fijación(C)

3Testa motore Motorkop Cabezal del motor

4Cassa ingranaggi Tandwielkast Caja de engranajes

5Raccoglipolvere Stofzak Bolsa para el polvo

6Marcatore laser (Solo C10FCH2) Lasermarkeerinrichting Marcador láser (Sólo C10FCH2)

(Alleen voor C10FCH2)

7Piatto girevole Draaischijf Placa giratoria

8Vite ad alette da 6 mm 6 mm Vleugelbout Perno de aletas de 6 mm

9Gruppo morsa Bankschroef Conjunto del tornillo de carpintero

;Guida secondaria (B) Subgeleider (B) Tope-guía secundario (B)

AGuida de appoggio (B) Geleider (B) Protección (B)

BPiatto girevole Draaitafel Plataforma

CManico laterale Zijgreep Asa lateral

DLeva Hendel Palanca

EIndicatore (A) Indicator (A) Indicador (A)

(Per la scala di quartabuono) (Voor verstekschaal) (Para escala de nivel)

FInserimento tavola Tafel-inzetstuk Inserto de mesa

GGuida de appoggio (A) Geleider (A) Protección (A)

HIndicatore (B) Indicator (B) Indicador (B)

(Per scala di smussatura) (Voor Afschuinschaal) (Para escala en Bisel)

IProtezione inferiore Onderste afscherming Protector inferior

JLama sega Zaagblad Cuchilla de sierra

KMotore Motor Motor

LTarghetta Specificatieplaatje Placa de identificación

MInterruttore a grilletto Startschakelaar Gatillo

Interruttore (Per marcatore laser) Schakelaar Interruptor (Para marcador láser)

N(Solo C10FCH2) (Voor lasermarkeerinrichting) (Sólo C10FCH2)

(Alleen voor C10FCH2)

OBase Basis Base

PSupporto (B) Houder (B) Soporte (B)

QLeva morsetto Klemhendel Palanca de fijación

RPerno di blocco Vergrendelpen Pasador de bloqueo

SCondotto Buis Conducto

TAngolo Retto Rechte Hoek Ángulo recto

URiga Lijn Línea

VSegnale di Avvertimento Waarschuwingssymbool Señal de precaución

WBullone da 6 mm 6 mm bout Perno de 6 mm

XVite M6 × 20 M6 × 20 Schroef M6 × 20 tornillos

YPortavite Schroefhouder Sujetador de rosca

ZVite ad alette da 6 mm (B) 6 mm Vleugelbout (B) Perno de aletas de 6 mm (B)

[Albero della Morsa Bankschroef Schacht Eje de tornillo de carpintero

\Vite ad alette da 6 mm (A) 6 mm Vleugelbout (A) Perno de aletas de 6 mm (A)

]Pezzo da lavorare Werkstuk Pieza de trabajo

`Piastra morsa Klemplaat Placa de tornillo

aManopola Knop Perilla

bVite piatta M6 M6 Platkopschroef Tornillo plano M6

cPiastra (A) Schijf (A) Placa (A)

dDado di nylon M6 M6 Nylon moer Tuerca de nylon M6

00Table_C10FCH2_WE_7L 3/11/09, 9:527

Italiano Nederlands Español

eBullone M10 M10 Bout Perno M10

fLinea laser Laserstreep Línea de láser

gScanalatura Groef Ranura

hChiave a barra esagonale da 4 mm Imbus Steeksleutel Llave de barra hexagonal de

4 mm 4 mm

iMarcatura (pre-contrassegnato) Markering (pre-pre-marked) Marcaje (pre-marcado)

jScala di quartabuono Verstekschaal Escala de ingletes

kSupporto (Accessori opzionali) Houder (Optionele toebehoren) Soporte (Accessorio opcionales)

lQuadrato di acciaio Stalen winkelhaak Escuadra de acero

mDado ad alette da 6 mm 6 mm vleugelmoer Tuerca de aletas de 6 mm

(Accessorio opzionale) (Optioneel toebehoren) (Accesorio opcional)

nBullone di regolazione altezza da Hoogte-afstelbout 6 mm Perno de ajuste de altura de

6 mm (Accessorio opzionale) (Optioneel toebehoren) 6 mm (Accesorio opcional)

oSuperficie della base Voetplaat Superficie de la base

pVite ad alette da 6 mm 6mm Vleugelbout Perno de aletas de 6 mm

(Accessorio opzionale) (Optioneel toebehoren) (Accesorio opcional)

qFermo (Accessori opzionali) Aanslag (Optionele toebehoren) Retén (Accessorio opcionales)

rVite ad alette da 6 mm 6 mm Vleugelbout Perno de aletas de 6 mm

(Accessorio opzionale) (Optionele toebehoren) (Accessorio opcional)

sVite ad alette da 6 mm 6 mm Vleugelbout Perno de aletas de 6 mm

Gruppo morsa di modanatura a Kroonvormklem Conj. de tornillo de carpintero

tcorona (Accessorio opzionale) (Optioneel toebehoren) para moldura en vértice

(Accesorio opcional)

uVite ad alette da 6 mm 6 mm Vleugelbout Perno de aletas de 6 mm

vVite ad alette da 6 mm 6 mm Vleugelbout Perno de aletas de 6 mm

wFermo per modanatura a corona Kroonvormstopper (L) Retén de moldura en vértice

(L) (Accessorio opzionale) (Optioneel toebehoren) (L) (Accesorio opcional)

xFermo per modanatura a corona Kroonvormstopper (R) Retén de moldura en vértice

(R) (Accessorio opzionale) (Optioneel toebehoren) (R) (Accesorio opcional)

yBullone a manopola da 6 mm 6 mm bout Perno de perilla de 6 mm

zManopola Knop Perilla

{Modanatura a corona Kroonvorm Moldura en vértice

|Vite da macchina da 4 mm 4 mm Machine Schroef Tornillo de máquina de 4 mm

}Coperchio dell’alberino Drijfas-afdekking Cubierta de husillo

~Fermo dell’alberino Spilvergrendeling Seguro del eje

åChiave chisa de 10 mm 10 mm naafbussleutel Lllave de tubo de 10 mm

çRondella (B) Sluitring (B) Arandela (B)

†Bullone Schroef Perno

¢Rondella Sluitring Arandela

£Rondella (A) Sluitring (A) Arandela (A)

§Colore (A) Kleur (A) Color (A)

•Bullone a Testa esagonale Imbus bout Perno de cabeza hexagonal

¶Quadrato di acciaio Stalen winkelhaak Escuadra de acero

ßRiga di limite usura Slijtagegrens Línea de límite de desgaste

®Scanalatura per elemento motore Groef Schroevendraaier Ranura para herramienta

©Coperchio spazzola Borstel Kap Tapa de cepillo

00Table_C10FCH2_WE_7L 3/11/09, 9:528

Português

1Empunhadeira

2Alavanca de bloqueio (C)

3Cabeça do motor

4Caixa de engrenagens

5Coletor de poeira

6Marcador a laser

(Somente no C10FCH2)

7Placa de rotação

8Parafuso de borboleta de 6 mm

9Conjunto de morsa

?Subguia (B)

AGuia (B)

BMesa rotatória

CEmpunhadeira lateral

DAlavanca

EIndicador (A)

(Para régua de entalhe)

FCalço de mesa

GGuia (A)

HIndicador (B)

(para escala de bisel)

IGuarda da lâmina inferior

JLâmina de serra

KMotor

LPlaca de identificação

MGatilho do interruptor

Interruptor (Para marcador a laser)

(Somente no C10FCH2)

OBase

PAlça (B)

QAlavanca de aperto

RPino de travamento

SConduta

TÂngulo direito

ULinha

VSinal de aviso

WParafuso de 6 mm

XParafuso M6 × 20

YSuporte do parafuso

ZParafuso de borboleta de 6 mm (B)

[Veio do torno

\Parafuso de borboleta de 6 mm (A)

]Peça de trabalho

`Placa da morsa

aBotão

bParafuso de cabeça chata M6

cPlaca (A)

dPorca de nylon M6

Português

eParafuso M10

fLinha a laser

gSulco

Chave de barra sextavada de 4 mm

iMarca

jRégua de entalhe

kAlça (Acessório opcional)

lRégua de aço

Porca de asas de 6 mm

(Acessório opcional)

nParafuso de ajuste de altura de

6 mm (Acessório opcional)

oSuperfície de base

pParafuso de borboleta de 6 mm

(Acessório opcional)

qTrava (Acessório opcional)

rParafuso de borboleta de 6 mm

(Acessório opcional)

sVite ad alette da 6 mm

Conjunto de morsa de moldura

tda coroa (Acessório opcional)

uParafuso de borboleta de 6 mm

vParafuso de borboleta de 6 mm

wObturador de moldura da

coroa (L) (Acessório opcional)

xObturador de moldura da

coroa (R) (Acessório opcional)

yParafuso de botão de 6 mm

zBotão

{Moldura da coroa

|Parafuso de máquina de 4 mm

}Protetor da haste

~Trava da haste

åChave de caixa de 10 mm

çArruela (B)

†Parafuso

¢Arruela

£Arruela (A)

§Cor (A)

•Parafuso de cabeça sextavada

¶Régua de aço

ßLinha de limite de desgaste

®Ranhura para chave

©Tampa da escova

00Table_C10FCH2_WE_7L 3/11/09, 9:529

Symbols

WARNING

The following show symbols used

for the machine. Be sure that you

understand their meaning before

use.

Symbole

WARNUNG

Die folgenden Symbole werden für

diese Maschine verwendet. Achten

Sie darauf, diese vor der

Verwendung zu verstehen.

Symboles

AVERTISSEMENT

Les symboles suivants sont utilisés

pour l’outil. Bien se familiariser

avec leur signification avant

d’utiliser l’outil.

Simboli

AVVERTENZA

Di seguito mostriamo i simboli

usati per la macchina. Assicurarsi

di comprenderne il significato

prima dell’uso.

Read all safety warnings and all

instructions.

Failure to follow the warnings and

instructions may result in electric

shock, fire and/or serious injury.

Always wear eye

protection.

Lesen Sie sämtliche

Sicherheitshinweise und

Anweisungen durch.

Wenn die Warnungen und

Anweisungen nicht befolgt

werden, kann es zu Stromschlag,

Brand und/oder ernsthaften

Verletzungen kommen.

Lire tous les avertissements de

sécurité et toutes les instructions.

Tout manquement à observer ces

avertissements et instructions peut

engendrer des chocs électriques,

des incendies et/ou des blessures

graves.

Leggere tutti gli avvertimenti di

sicurezza e tutte le istruzioni.

La mancata osservanza degli

avvertimenti e delle istruzioni

potrebbe essere causa di scosse

elettriche, incendi e/o gravi lesioni.

Symbolen

WAARSCHUWING

Hieronder staan symbolen

afgebeeld die van toepassing zijn op

deze machine. U moet de betekenis

hiervan begrijpen voor gebruik.

Símbolos

ADVERTENCIA

A continuación se muestran los

símbolos usados para la máquina.

Asegúrese de comprender su

significado antes del uso.

Símbolos

AVISO

A seguir aparecem os símbolos

utilizados pela máquina. Assimile

bem seus significados antes do

uso.

Lees alle waarschuwingen en

instructies aandachtig door.

Nalating om de waarschuwingen

en instructies op te volgen kan in

een elektrische schok, brand en/of

ernstig letsel resulteren.

Draag altijd

oogbescherming.

Lea todas las instrucciones y

advertencias de seguridad.

Si no se siguen las advertencias e

instrucciones, podría producirse

una descarga eléctrica, un

incendio y/o daños graves.

Utilice siempre una

protección ocular.

Leia todas as instruções e avisos

de segurança.

Se não seguir todas as instruções

e os avisos, pode provocar um

choque eléctrico, incêndio e/ou

ferimentos graves.

Utilize sempre

protecção para os olhos.

Tragen Sie immer einen

Augenschutz. Indossate sempre le

protezioni oculari.

Only for EU countries

Do not dispose of electric tools

together with household waste

material!

In observance of European

Directive 2002/96/EC on waste

electrical and electronic equipment

and its implementation in

accordance with national law,

electric tools that have reached the

end of their life must be collected

separately and returned to an

environmentally compatible

recycling facility.

Nur für EU-Länder

Werfen Sie Elektrowerkzeuge nicht

in den Hausmüll!

Gemäss Europäischer Richtlinie

2002/96/EG über Elektro- und

Elektronik- Altgeräte und

Umsetzung in nationales Recht

müssen verbrauchte

Elektrowerkzeuge getrennt

gesammelt und einer

umweltgerechten

Wiederververtung zugeführt

werden.

Pour les pays européens

uniquement

Ne pas jeter les appareils électriques

dans les ordures ménagères!

Conformément à la directive

européenne 2002/96/EG relative aux

déchets d’équipements électriques

ou électroniques (DEEE), et à sa

transposition dans la législation

nationale, les appareils électriques

doivent être collectés à part et être

soumis à un recyclage respectueux

de l’environnement.

Solo per Paesi UE

Non gettare le apparecchiature

elettriche tra i rifiuti domestici.

Secondo la Direttiva Europea

2002/96/CE sui rifiuti di

apparecchiature elettriche ed

elettroniche e la sua attuazione in

conformità alle norme nazionali, le

apparecchiature elettriche esauste

devono essere raccolte

separatamente, al fine di essere

reimpiegate in modo eco-

compatibile.

Alleen voor EU-landen

Geef elektrisch gereedschap niet

met het huisvuil mee!

Volgens de Europese richtlijn 2002/

96/EG inzake oude elektrische en

elektronische apparaten en de

toepassing daarvan binnen de

nationale wetgeving, dient

gebruikt elektrisch gereedschap

gescheiden te worden ingezameld

en te worden afgevoerd naar een

recycle bedrijf dat voldoet aan de

geldende milieu-eisen.

Sólo para países de la Unión

Europea

¡No deseche los aparatos eléctricos

junto con los residuos domésticos!

De conformidad con la Directiva

Europea 2002/96/CE sobre residuos

de aparatos eléctricos y electrónicos

y su aplicación de acuerdo con la

legislación nacional, las

herramientas eléctricas cuya vida

útil haya llegado a su fin se deberán

recoger por separado y trasladar a

una planta de reciclaje que cumpla

con las exigencias ecológicas.

Apenas para países da UE

Não deite ferramentas eléctricas

no lixo doméstico!

De acordo com a directiva

europeia 2002/96/CE sobre

ferramentas eléctricas e

electrónicas usadas e a

transposição para as leis

nacionais, as ferramentas

eléctricas usadas devem ser

recolhidas em separado e

encaminhadas a uma instalação de

reciclagem dos materiais

ecológica.

Toujours porter des

verres de protection.

Always wear hearing

protection. Stets Gehörschutz

tragen.

Porter des protections

anti-bruit en permanence.

Indossare sempre i

dispositivi di protezione

acustica.

Draag altijd

gehoorbescherming.

Utilice siempre

protecciones auriculares.

Use sempre proteção

auditiva.

00Table_C10FCH2_WE_7L 3/11/09, 9:5210

English

GENERAL OPERATIONAL PRECAUTIONS

WARNING! When using electric tools, basic safety

precautions should always be followed to reduce the risk

of fire, electric shock and personal injury, including the

following.

Read all these instructions before operating this product

and save these instructions.

For safe operations:

1. Keep work area clean. Cluttered areas and benches

invite injuries.

2. Consider work area environment. Do not expose

power tools to rain. Do not use power tools in damp

or wet locations. Keep work area well lit.

Do not use power tools where there is risk to cause

fire or explosion.

3. Guard against electric shock. Avoid body contact

with earthed or grounded surfaces (e.g. pipes,

radiators, ranges, refrigerators).

4. Keep children and infirm persons away. Do not let

visitors touch the tool or extension cord. All visitors

should be kept away from work area.

5. Store idle tools. When not in use, tools should be

stored in a dry, high or locked up place, out of reach

of children and infirm persons.

6. Do not force the tool. It will do the job better and

safer at the rate for which it was intended.

7. Use the right tool. Do not force small tools or

attachments to do the job of a heavy duty tool. Do

not use tools for purposes not intended; for example,

do not use circular saw to cut tree limbs or logs.

8. Dress properly. Do not wear loose clothing or

jewelry, they can be caught in moving parts. Rubber

gloves and non-skid footwear are recommended

when working outdoors. Wear protecting hair

covering to contain long hair.

9. Use eye protection. Also use face or dust mask if

the cutting operation is dusty.

10. Connect dust extraction equipment.

Cutting operation by this compound miter saw may

produce considerable amount of dust from

extraction duct on fixed guard.

(Dust material: Wood or Aluminium)

If devices are provided for the connection of dust

extraction and collection facilities ensure these are

connected and properly used.

11. Do not abuse the cord. Never carry the tool by the

cord or yank it to disconnect it from the receptacle.

Keep the cord away from heat, oil and sharp edges.

12. Secure work. Use clamps or a vise to hold the work.

It is safer than using your hand and it frees both

hands to operate tool.

13. Do not overreach. Keep proper footing and balance

at all times.

14. Maintain tools with care. Keep cutting tools sharp

and clean for better and safer performance. Follow

instructions for lubrication and changing

accessories. Inspect tool cords periodically and if

damaged, have it repaired by authorized service

center. Inspect extension cords periodically and

replace, if damaged. Keep handles dry, clean, and

free from oil and grease.

15. Disconnect tools. When not in use, before servicing,

and when changing accessories such as blades, bits

and cutters.

16. Remove adjusting keys and wrenches. Form the

habit of checking to see that keys and adjusting

wrenches are removed from the tool before turning

it on.

17. Avoid unintentional starting. Do not carry a plugged-

in tool with a finger on the switch. Ensure switch is

off when plugging in.

18. Use outdoor extension leads. When tool is used

outdoors, use only extension cords intended for

outdoor use.

19. Stay alert. Watch what you are doing. Use common

sense. Do not operate tool when you are tired.

20. Check damaged parts. Before further use of the tool,

a guard or other part that is damaged should be

carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, free running of

moving parts, breakage of parts, mounting and any

other conditions that may affect its operation. A

guard or other part that is damaged should be

properly repaired or replaced by an authorized

service center unless otherwise indicated in this

handling instructions. Have defective switches

replaced by an authorized service center. Do not use

the tool if the switch does not turn it on and off.

21. Warning

The use of any accessory or attachment, other than

those recommended in this handling instructions,

may present a risk of personal injury.

22. Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant

safety requirements. Repairs should only be carried

out by qualified persons using original spare parts.

Otherwise this may result in considerable danger

to the user.

PRECAUTIONS ON USING COMPOUND MITER SAW

1. Keep the floor area around the machine level. Well

maintained and free of loose materials e.g. chips

and cut-offs.

2. Provide adequate general or localized lighting.

3. Do not use power tools for applications other than

those specified in the handling instructions.

4. Repairing must be done only by authorized service

facility. Manufacturer is not responsible for any

damages and injuries due to the repair by the

unauthorized persons as well as the mishandling of

the tool.

5. To ensure the designed operational integrity of

power tools, do not remove installed covers or

screws.

6. Do not touch movable parts or accessories unless

the power source has been disconnected.

7. Use your tool at lower input than specified on the

nameplate; otherwise, the finish may be spoiled and

working efficiency reduced due to motor overload.

8. Do not wipe plastic parts with solvent. Solvents such

as gasoline, thinner, benzine, carbon tetrachloride,

alcohol, may damage and crack plastic parts. Do not

wipe them with such solvent. Clean plastic parts with

a soft cloth lightly dampened with soapy water.

9. Use only original HiKOKI replacement parts.

10. This tool should only be disassembled for

replacement of carbon brushes.

11. The exploded assembly drawing on this handling

instructions should be used only for authorized

service facility.

12. Never cut ferrous metals or masonry.

13. Adequate general or localized lighting is provided.

Stock and finished workpieces are located close to

the operators normal working position.

14. Wear suitable personal protective equipment when

necessary, this could include:

Hearing protection to reduce the risk of induced

hearing loss.

Eye protection to reduce the risk of injuring an eye.

Respiratory protection to reduce the risk of

inhalation of harmful dust.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5211

English

Gloves for handling saw blades (saw blades shall

be carried in a holder wherever practicable) and

rough material.

15. The operator is adequately trained in the use,

adjustment and operation of the machine.

16. Refrain from removing any cut-offs or other parts

of the workpiece from the cutting area whilst the

machine is running and the saw head is not in the

rest position.

17. Never use the compound miter saw with its lower

guard locked in the open position.

18. Ensure that the lower guard moves smoothly.

19. Do not use the saw without guards in position, in

good working order and properly maintained.

20. Use correctly sharpened saw blades. Observe the

maximum speed marked on the saw blade.

21. Do not use saw blades which are damaged or

deformed.

22. Do not use saw blades manufactured from high

speed steel.

23. Use only saw blades recommended by HiKOKI.

Use of saw blade comply with EN847-1.

24. The saw blades should be from 235 mm to 255 mm

external diameter ranges.

25. Select the correct saw blade for the material to be

cut.

26. Never operate the compound miter saw with the

saw blade turned upward or to the side.

27. Ensure that the workpiece is free of foreign matter

such as nails.

28. Replace the table insert when worn.

29. Do not use the saw to cut other than aluminium,

wood or similar materials.

30. Do not use the saw to cut other materials than those

recommended by the manufacturer.

31. Blade replacement procedure, including the method

for repositioning and a warning that this must be

carried out correctly.

32. Connect the compound miter saw to a dust

collecting device when sawing wood.

33. Take care when slotting.

34. When transporting or carrying the tool, do not grasp

the holder. Grasp the handle instead of the holder.

35. Start cutting only after motor revolution reaches

maximum speed.

36. Promptly cut OFF the switch when abnormality

observed.

37. Shut off power and wait for saw blade to stop before

servicing or adjusting tool.

38. During a miter or bevel cut the blade should not be

lifted until it has stopped rotation completely.

39. Take all the possibility of residual risks in cutting

operation into your consideration, such as the laser

radiation to your eyes, the inadvertent access to

moving parts on slide mechanical parts on machine

and so on.

59 mm × 144 mm

0° or

89 mm × 101 mm

Miter 45° 59 mm × 102 mm

Bevel Left 45° 41 mm × 144 mm

Compound (Bevel Left 45°, Miter 45°)

41 mm × 102 mm

Saw Blade Dimensions (oD × iD × Thickness) 255 mm × 30 mm × 2.3 mm

Miter Cutting Angle Right and Left 0° – 52°

Bevel Cutting Angle Left 0° – 45°

Compound Cutting Angle Miter (Right and Left) 0° – 45°

Voltage (by areas)* (110 V, 230 V)

Power Input* 1520 W

No-Load Speed 5000 min–1

Machine Dimensions (Width × Depth × Height) 460 mm × 628 mm × 561 mm

Weight (Net) 12 kg (C10FCH2) / 11.9 kg (C10FCE2)

Maximum output Po<3 mW Class Laser Product

(Iambda) 654 nm

Laser medium Laser Diode

Max. Cutting

Capacity

Height × Width

Laser Marker

(Only Model C10FCH2)

SPECIFICATIONS

* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) 255 mm TCT Saw blade (mounted on tool) ............. 1

(2) Dust bag ...................................................................... 1

(3) 10 mm Box wrench .................................................... 1

(4) Vise Assembly ............................................................ 1

(5) 4 mm Hex.bar wrench (only C10FCH2) .................... 1

(6) Sub Fence (B) ............................................................. 1

(7) Flat screw .................................................................... 1

(8) M6 Nylon nut .............................................................. 1

(9) Plate (A) ....................................................................... 1

(10) Holder (B) .................................................................. 1

(11) Side handle ............................................................... 1

Standard accessories are subject to change without

notice.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5212

English

OPTIONAL ACCESSORIES (SOLD SEPARATELY)

(1) Extension Holder and Stopper

(2) Crown molding Vise Ass'y (Include Crown molding

Stopper (L))

(3) Crown molding Stopper (L)

(4) Crown molding Stopper (R)

Optional accessories are subject to change without notice.

APPLICATION

䡬Cutting various types of aluminium sash and wood.

UNPACKING

䡬Carefully unpack the power tool and all related items

(standard accessories).

䡬Check carefully to make certain all related items

(standard accessories) are present.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the trigger

switch is in the ON position, the power tool will start

operating immediately, inviting serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be kept

as short as practicable.

4. When the power tool is prepared for shipping, its

main parts are secured by a locking pin

Move the handle slightly so that the locking pin can

be disengaged.

CAUTION

䡬Set for transport

Lock the locking pin into the gear case (Fig. 3).

Remove a 6 mm wing bolt.Turn the turn plate as the

Fig. 5, and fix it again with the 6 mm wing bolt.

Lower guard cover the teeth of the blade to the front

of the machine.

䡬Cutting work

Move the handle slightly so that the locking pin can

be disengaged.

Remove a 6 mm wing bolt.Turn the turn plate as Fig.

6, and fix it again with the 6 mm wing bolt.

5. Attach the dust bag to the main unit (Fig. 1)

(1) When the dust bag has become full of sawdust, dust

will be blown out of the dust bag when the saw blade

rotates.

Check the dust bag periodically and empty it before it

becomes full.

(2) During bevel and compound cutting, attach the dust

bag at a right angle to the base surface as shown in

Fig. 4.

CAUTION

䡬Empty the dust bag frequently to prevent the duct and

the safety cover from becoming clogged.

Sawdust will accumulate more quickly than normal

during bevel cutting.

6. Installation

Ensure that the machine is always fixed to bench.

Attach the power tool to a level, horizontal work bench.

Select 8 mm diameter bolts suitable in length for the

thickness of the work bench.

Bolt length should be at least 35 mm plus the thickness

of the work bench.

For example, use 8 mm × 60 mm bolts for a 25 mm

thick work bench.

ADJUSTING THE POWER TOOL PRIOR TO USE

CAUTION

Make all necessary adjustments before inserting the

plug in the power source.

1. Check to see that the lower guard operates smoothly

CAUTION

䡬This compound miter saw is equipped with a saw

head lock as safety device.

䡬To lower the saw head to cut, the lock must be released

by pressing the lock lever (C) with your thumb.

(1) When you push down the handle while pushing the

lock lever (C), check that the lower guard revolves

smoothly (Fig. 7).

(2) Next, check that the lower guard returns to the original

position when the handle is raised.

PRACTICAL APPLICATIONS

WARNING

䡬To avoid personal injury, never remove or place a

workpiece on the table while the tool is being

operated.

䡬Never place your limbs inside of the line next to

warning sign while the tool is being operated. This

may cause hazardous conditions (see Fig. 8).

CAUTION

䡬It is dangerous to remove or install the workpiece

while the saw blade is turning.

䡬When sawing, clean off the shavings from the

turntable.

䡬If the shavings accumulate too much, the saw blade

from the cutting material will be exposed. Never

subject your hand or anything else to go near the

exposed blade.

1. Tightly secure the material by vise assembly to be

cut so that it does not move during cutting

2. Switch operation

Pulling the trigger turns the switch on. Releasing the

trigger turns the switch off.

3. Holder (B), clamp lever adjustment (Fig. 9)

Attach the included holder (B) in the position as shown

in Fig. 9 and adjust the holder (B) until its bottom

surface contacts the work bench surface. After

adjustments, securely tighten the 6mm bolt with the

included 10mm box wrench. Loosen the M6 × 20 screw

on the clamp lever and attach to a position where the

clamp lever can be easily operated.

4. Using the Vise Assembly (Standard accessory) (Fig. 10)

(1) The vise assembly can be mounted on either the left

fence {Fence (B)} or the right fence {Fence (A)} by

loosening the 6 mm wing bolt (A).

(2) The screw holder can be raised or lowered according

to the height of the workpiece by loosening the 6 mm

wing bolt (B). After the adjustment, firmly tighten the

6 mm wing bolt (B) and fix the screw holder.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5213

English

(3) Turn the upper knob and securely fix the workpiece

in position.

WARNING

䡬Always firmly clamp or vise to secure the workpiece

to the fence; otherwise the workpiece might be thrust

from the table and cause bodily harm.

CAUTION

䡬Always confirm that the motor head does not contact

the vise assembly when it is lowered for cutting. If

there is any danger that it may do so, loosen the 6

mm wing bolt and move the vise assembly to a

position where it will not contact the saw blade.

5. Install the sub fence (B) (Fig. 11)

In the case of direct angle cutting and angle cutting,

use the sub fence. The sub fence (B) can be installed

on the right side of the guide fence (B). Place the

attached plate (A) in the position as shown in Fig. 11,

insert the tip in the groove of fence (B) and

simultaneously, insert flathead screw M6 into fence (B),

sub fence (B), and plate (A), then tighten nylon nut M6

with the included 10mm box wrench until the sub fence

(B) can smoothly rotate. Then, you can realize stable

cutting of the material with a wide back face.

WARNING

䡬In the case of left bevel cutting, rotate the sub fence

(B). Supposing it is not able to rotate it, it will contact

the blade or some part of the tool, causing in serious

injury to operator.

6. Using an ink line

Upon lowering the motor section, the lower guard is

raised and the saw blade appears.

Align the ink line with the saw blade.

CAUTION

Never lift the lower guard while the saw blade is

rotating.

The sub fence will not only make contact and

adversely affect cutting accuracy, this could also result

in damage to the guard.

7. Install the side handle (Fig. 12)

Remove the M10 bolt and install the side handle that

came enclosed with this unit.

8. Position adjustment of laser line (Only Model

C10FCH2)

Ink lining can be easily made on this tool to the laser

marker. A switch lights up the laser marker (Fig. 13).

Depending upon your cutting choice, the laser line

can be aligned with the left side of the cutting width

(saw blade) or the ink line on the right side.

The laser line is adjusted to the width of the saw blade

at the time of factory shipment. Adjust the positions

of the saw blade and the laser line taking the following

steps to suit the use of your choice.

(1) Light up the laser marker and make a groove of about 5

mm deep on the workpiece that is about 38 mm in height

and 89 mm in width. Hold the grooved workpiece by vise

as it is and do not move it.

(2) Then insert a 4 mm hex. bar wrench in the 12 diameter

hole on the side of the gear case, turn the hex. socket

set screw to move the laser line. (If you turn the Hex.

socket screw clockwise, the laser line will shift to the

right and if you turn it counterclockwise, the laser line

will shift to the left.) When you work with the ink line

aligned with the left side of the saw blade, align the

laser line with the left end of the groove (Fig. 14). When

you align it with the right side of the saw blade, align

the laser line with the right side of the groove.

(3) After adjusting the position of the laser line, draw a

right-angle ink line on the workpiece and align the

ink line with the laser line. When aligning the ink line,

slide the workpiece little by little and secure it by vise

at a position where the laser line overlaps with the

ink line. Work on the grooving again and check the

position of the laser line. If you wish to change the

laser line’s position, make adjustments again

following the steps from (1) to (3).

WARNING (Fig. 16 and Fig. 17)

䡬Make sure before plugging the power plug into the

receptacle that the main body and the laser marker

are turned off.

䡬Exercise utmost caution in handling a switch trigger for

the position adjustment of the laser line, as the power

plug is plugged into the receptacle during operation.

If the switch trigger is pulled inadvertently, the saw

blade can rotate and result in unexpected accidents.

䡬Do not remove the laser marker to be used for other

purposes.

CAUTION

䡬Laser radiation - Do not stare into beam.

䡬Laser radiation on work table. Do not stare into beam.

If your eye is exposed directly to the laser beam, it

can be hurt.

䡬Do not dismantle it.

䡬Do not give strong impact to the laser marker (main

body of tool); otherwise, the position of a laser line

can go out of order, resulting in the damage of the

laser marker as well as a shortened service life.

䡬Keep the laser marker lit only during a cutting

operation. Prolonged lighting of the laser marker can

result in a shortened service life.

䡬Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

NOTE

䡬Perform cutting by overlapping the ink line with the

laser line.

䡬When the ink line and the laser line are overlapped,

the strength and weakness of light will change,

resulting in a stable cutting operation because you

can easily discern the conformity of lines. This ensures

the minimum cutting errors.

䡬In outdoor or near-the-window operations, it may

become difficult to observe the laser line due to the

sunlight. Under such circumstances, move to a place

that is not directly under the sunlight and engage in

the operation.

䡬Do not tug on the cord behind the motor head or hook

your finger, wood and the like around it; otherwise,

the cord may come off and the laser marker may not

be lit up.

䡬Check and make sure on a periodic basis if the position

of the laser line is in order. As regards the checking

method, draw a right-angle ink line on the workpiece

with the height of about 38 mm and the width of 89

mm, and check that the laser line is in line with the

ink line [The deviation between the ink line and the

laser line should be less than the ink line width (0.5

mm)] (Fig. 15).

9. Cutting operation

(1) As shown in Fig. 18 the width of the saw blade is the

width of the cut. Therefore, slide the workpiece to the

right (viewed from the operator’s position) when

length is desired, or to the left when length is

desired.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5214

English

(Only Model C10FCH2)

If a laser marker is used, align the laser line with the

left side of the saw blade, and then align the ink line

with the laser line.

(2) Once the saw blade reaches maximum speed, slowly

push down the handle while pushing the lock lever

material to be cut.

(3) Once the saw blade contacts the workpiece, push the

handle down gradually to cut into the workpiece.

(4) After cutting the workpiece to the desired depth, turn

the power tool OFF and let the saw blade stop

completely before raising the handle from the

workpiece to return it to the full retract position.

CAUTION

䡬For maximum dimensions for cutting, refer to

“SPECIFICATIONS” table.

䡬Increased pressure on the handle will not increase the

cutting speed. On the contrary, too much pressure

may result in overload of the motor and/or decreased

cutting efficiency.

䡬Confirm that the trigger switch is turned OFF and the

power plug has been removed from the receptacle

whenever the tool is not in use.

䡬Always turn the power off and let the saw blade stop

completely before raising the handle from the

workpiece. If the handle is raised while the saw blade

is still rotating, the cut-off piece may become jammed

against the saw blade causing fragments to scatter

about dangerously.

䡬Every time one cutting of deep-cutting operation is

finished, turn the switch off, and check that the saw

blade has stopped. Then raise the handle, and return

it to the full retract position.

䡬Be absolutely sure to remove the cut material from

the top of the turntable, and then proceed to the next

step.

10. Miter cutting procedures

(1) Loosen the side handle and push the lever for angle

stoppers. Then, adjust the turntable until the indicator

aligns with desired setting on the miter scale (Fig. 19).

(2) Re-tighten the side handle to secure the turntable in

the desired position.

NOTE

䡬Positive stops are provided at the right and left of the

0° center setting, at 15°, 22.5°, 31.6° and 45° settings.

Check that the miter scale and the tip of the indicator

are properly aligned.

䡬Operation of the saw with the miter scale and indicator

out of alignment, or with the side handle not properly

tightened, will result in poor cutting precision.

CAUTION

䡬Never remove the side handle; use of the tool without

it would be hazardous.

To prevent an accident or personal injury always firmly

tighten the miter handle.

11. Bevel cutting procedures (Fig. 20 and Fig. 21)

(1) Loosen the clamp lever and bevel the saw blade to

the left.

(2) Adjust the bevel angle to the desired setting while

watching the bevel angle scale and indicator, then

secure the clamp lever.

WARNING

䡬When the workpiece is secured on the left or right

side of the blade, the short cut-off portion will come

to rest on the right or left side of the saw blade. Always

turn the power off and let the saw blade stop

completely before raising the handle from the

workpiece.

If the handle is raised while the saw blade is still

rotating, the cut-off piece may become jammed

against the saw blade causing fragments to scatter

about dangerously.

䡬When stopping the bevel cutting operation halfway,

start cutting after pulling back the motor head to the

initial position.

Starting from halfway, without pulling back, causes

the safety cover to be caught in the cutting groove of

the workpiece and to contact the saw blade.

12. Compound cutting procedures

Compound cutting can be performed by following the

instructions in 9 and 10 above. For maximum

dimensions for compound cutting, refer to

“SPECIFICATIONS” table.

CAUTION

䡬Always secure the workpiece with the right hand side

for compound cutting. Never rotate the table to the

right for compound cutting, because the saw blade

might then contact the clamp or vise that secures the

workpiece, and cause personal injury or damage.

13. Cutting long materials

When cutting long materials, use an auxiliary platform

which is the same height as the holder (optional

accessory) and base of the special auxiliary

equipment.

Capacity: wooden material (W × H × L)

120 mm × 40 mm × 1000 mm

14. Installing the holders (Optional accessory)

The holders help keep longer workpieces stable and

in place during the cutting operation.

(1) As indicated in Fig. 22, use a steel square for aligning

the upper edge of the holders with the base surface.

Loosen the 6 mm wing nut. Turn a height adjustment

bolt 6 mm, and adjust the height of the holder.

(2) After adjustment, firmly tighten the wing nut and

fasten the holder with the 6 mm knob bolt (optional

accessory). If the length of Height Adjustment Bolt 6

mm is insufficient, spread a thin plate beneath. Make

sure the end of Height Adjustment Bolt 6 mm does

not protrude from the holder.

15. Stopper for precision cutting (Stopper and holder are

optional accessory)

The stopper facilitates continuous precision cutting

in lengths of 280 mm to 450 mm.

To install the stopper, attach it to the holder with the 6

mm wing bolt as shown in Fig. 23.

16. Confirmation for use Crown molding vise, Crown

molding Stopper (L) and (R) (Optional accessory)

(1) Crown molding Stopper (L) and (R) (optional

accessories) allow easier cuts of crown molding

without tilting the saw blade. lnstall them in the base

both-sides side to be shown in Fig. 24. After inserting

tighten the 6 mm knob bolts to secure the Crown

molding Stoppers.

(2) The crown molding vise (B) (Optional accessory) can

be mounted on either the left fence (Fence (B)) or the

right fence (Fence (A)). lt can unite with the slope of

the crown molding and vice can be pressed down.

Then turn the upper knob, as necessary, to securely

attach the crown molding in position. To raise or lower

01Eng_C10FCH2_WE_7L 3/11/09, 9:5215

English

the vise assembly, first loosen the 6 mm wing bolt.

After adjusting the height, firmly tighten the 6 mm

wing bolt; then turn the upper knob, as necessary, to

securely attach the crown molding in position (See

Fig 25).

Position crown molding with its WALL CONTACT

EDGE against the guide fence and its CEILING

CONTACT EDGE against the Crown molding Stoppers

as shown in Fig. 25. Adjust the Crown molding

Stoppers according to the size of the crown molding.

Tighten the 6 mm wing bolt to secure the Crown

molding Stoppers.

WARNING

䡬Always firmly clamp or vise to secure the crown

molding to the fence; otherwise the crown molding

might be thrust from the table and cause bodily harm.

Do not bevel cutting. The main body or saw blade

may contact the sub fence, resulting in an injury.

CAUTION

䡬Always confirm that the motor head (see Fig. 1) does

not contact the crown molding vise assembly when it

is lowered for cutting. If there is any danger that it

may do so, loosen the 6 mm knob bolt and move the

crown molding vise assembly to a position where it

will not contact the saw blade.

MOUNTING AND DISMOUNTING SAW BLADE

WARNING

䡬To prevent an accident or personal injury, always turn

off the trigger switch and disconnect the power plug

from the receptacle before removing or installing a

blade.

If cutting work is done in a state where the bolt is not

sufficiently tightened, the bolt can get loose, the blade

can come off, and the lower guard can get damaged,

resulting in injuries.

Also, check that the bolts are properly tightened before

plugging the power plug into the receptacle.

䡬If the bolts are attached or detached using tools other

than the 10 mm box wrench (standard accessory),

excessive or improperly tightening occurs, resulting

in injury.

1. Mounting the saw blade (Fig. 26, Fig. 27, Fig. 28 and

Fig. 29)

(1) Rotate the lower guard (plastic) to the top position.

(2) Use the driver to loosen the 4 mm screw fastening

the spindle cover and then remove the spindle cover.

(3) Press in spindle lock and loosen bolt with 10 mm box

wrench (standard accessory).

Since the bolt is left-hand threaded, loosen by turning

it to the right as show in Fig. 28.

NOTE

䡬If the spindle lock cannot be easily pressed in to lock

the spindle, turn the bolt with 10 mm box wrench

(standard accessory) while applying pressure on the

spindle lock.

The saw blade spindle is locked when the spindle lock

is pressed inward.

(4) Remove the bolt and washer (B).

(5) Lift the lower guard and mount the saw blade.

WARNING

When mounting the saw blade, confirm that the

rotation indicator mark on the saw blade and the

rotation direction of the gear case (see Fig. 1)are

properly matched.

(6) Thoroughly clean washer (B) and the bolt, and install

them onto the saw blade spindle.

(7) Press in the spindle lock and tighten the bolt by turning

it to the left by standard accessories wrench(10 mm

box wrench) as indicated in Fig. 28.

CAUTION

䡬Confirm that the spindle lock has returned to the

retract position after installing or removing the saw

blade.

䡬Tighten the bolt so it does not come loose during

operation.

䡬Confirm that the bolt has been properly tightened

before the power tool is started.

2. Dismounting the saw blade

Dismount the saw blade by reversing the mounting

procedures described in paragraph 1 above.

The saw blade can easily be removed after lifting the

lower guard.

CAUTION

䡬Never attempt to install saw blades except

235 mm – 255 mm in diameter.

MAINTENANCE AND INSPECTION

WARNING

To avoid an accident or personal injury, always

confirm the trigger switch is turned OFF and that the

power plug has been disconnected from the

receptacle before performing any maintenance or

inspection of this tool.

1. Inspecting the saw blade

Always replace the saw blade immediately upon the

first sign of deterioration or damage.

A damaged saw blade can cause personal injury and

a worn saw blade can cause ineffective operation and

possible overload to the motor.

CAUTION

䡬Never use a dull saw blade. When a saw blade is dull,

its resistance to the hand pressure applied by the tool

handle tends to increase, making it unsafe to operate

the power tool.

2. Inspecting the lever (Fig. 30 and Fig. 31)

If the M6 hexagonal head bolts (2) are loose, align the

sides of the fence and saw blade with the steel square.

After adjusting the saw blade and fence to a ninety-

degree angle, tighten the lever securing hexagonal

head bolts (2).

3. Inspecting the carbon brushes (Fig. 32 and Fig. 33)

The carbon brushes in the motor are expendable

parts.

If the carbon brushes become excessively worn, motor

trouble might occur.

Therefore, inspect the carbon brushes periodically and

replace them when they have become worn to the

wear limit line as shown in Fig. 32.

Also, keep the carbon brushes clean so that they will

slide smoothly within the brush holders.

The carbon brushes can easily be removed after

removal of the brush caps (see Fig. 33) with a slotted

(minus) screwdriver.

4. About Handling the Motor (see Fig. 1)

Winding of the motor is said to be the heart of this

tool. Exercise utmost caution not to damage the

winding by exposing it to wash oil or water.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5216

English

NOTE

䡬Accumulation of dust and the like inside the motor

can result in a malfunction.

After using the motor for 50 hours or so, carry out no-

load running, and blow in the dry air from a wind hole

at the motor's rear. Such action is effective to

discharge dust and the like.

5. Inspecting the screws

Regularly inspect each component of the power tool

for looseness.

Re-tighten screws on any loose part.

WARNING

䡬To prevent personal injury, never operate the power

tool if any components are loose.

6. Inspecting the lower guard for proper operation

Before each use of the tool, test the lower guard (see

Fig. 7) to assure that it is in good condition and that it

moves smoothly.

Never use the tool unless the lower guard operates

properly and it is in good mechanical condition.

7. Storage

After operation of the tool has been completed, check

that the following has been performed:

(1) Trigger switch is in OFF position,

(2) Power plug has been removed from the receptacle,

(3) When the tool is not in use, keep it stored in a dry

place out of the reach of children.

8. Lubrication

Lubricate the following sliding surfaces once a month

to keep the power tool in good operating condition

for a long time (Fig. 1 and Fig. 2).

Use of machine oil is recommended.

Oil supply points:

* Rotary portion of hinge

* Rotary portion of vise assembly

9. Cleaning

Periodically remove chips, dust and other waste

material from the surface of the power tool, especially

from the inside of the lower guard with a damp, soapy

cloth. To avoid a malfunction of the motor, protect it

from contact with oil or water.

(Only Model C10FCH2)

If the laser line becomes invisible due to chips and

the like adhered onto the window of the laser marker's

light-emitting section, wipe and clean the window with

a dry cloth or a soft cloth moistened with soapy water,

etc.

10. Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION

Repair, modification and inspection of HiKOKI Power

Tools must be carried out by a HiKOKI Authorized

Service Center.

Especially laser device should be maintained by the

authorized agent by laser manufacturer.

Always assign the repair of laser device to HiKOKI

Authorized Service Center.

This Parts List will be helpful if presented with the

tool to the HiKOKI Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

HiKOKI Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

NOTE

Due to HiKOKI’s continuing program of research and

development the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: -Neutral

Brown: -Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal

marked with the letter L or coloured red. Neither code

must be connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not

be applicable to other markets except The United

Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN61029.

The typical A-weighted sound pressure level: 95 dB (A)

The typical A-weighted sound power level: 108 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration

value: 2.6 m/s2.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5217

English

Information for power supply system to be used with

electric tools provided with rated voltage 230 V~

Switching operations of electric apparatus cause voltage

fluctuations.

The operation of this electric tool under unfavorable mains

conditions can have adverse effects to the operation of other

electric apparatus.

With a mains impedance equal or less than 0.29 Ohms

there will probably be no negative effects.

Usually, the maximum permissible mains impedance will

not be exceeded when the branch to the power outlet is

fed from a junction box with a service capacity of 25

ampere or higher.

In case of power failure, or when the power plug is pulled

out, immediately return the switch to OFF position. This

prevents an uncontrolled restart.

01Eng_C10FCH2_WE_7L 3/11/09, 9:5218

Deutsch

ALLGEMEINE VORSICHTSMASSNAHMEN

WARNUNG! Bei der Verwendung von Elektrowerkzeugen

müssen immer die grundlegenden Vorsichtsmaßnahmen

befolgt werden, um das Risiko von Feuer, elektrischem

Schlag und persönlicher Verletzung und den

nachfolgenden Punkten zu vermeiden.

Lesen Sie diese Anweisungen völlig, bevor Sie dieses

Erzeugnis verwenden, und bewahren Sie diese

Anweisungen auf.

Für sicheren Betrieb:

1. Der Arbeitsplatz sollte sauber gehalten werden.

Unaufgeräumte Arbeitsplätze und Werkbänke

erhöhen die Unfallgefahr.

2. Die Betriebsbedingungen beachten. Elektrowerkzeuge

sollten nicht dem Regen ausgesetzt werden.

Ebenfalls sollten Sie nicht an feuchten oder nassen

Plätzen gebraucht werden. Der Arbeitsplatz sollte

gut beleuchtet sein.

Verwenden Sie Elektrowerkzeuge nicht an Orten,

an denen die Gefahr von Feuer oder Explosion

besteht.

3. Schutzmaß nahmen gegen elektrische Schläge

treffen. Darauf achten, daß das Gehäuse nicht in

Kontakt mit geerdeten Flachen kommt (z.B. Rohre,

Radiatoren, Elektroherde, Kühlschränke).

4. Kinder und gebrechliche Personen sollten vom

Gerät ferngehalten werden. Andere Personen nicht

mit dem Werkzeug oder dem Verlängerungskabel

in Kontakt kommen lassen. Besucher sollten vom

Arbeitsbereich ferngehalten werden.

5. Nicht benutzte Werkzeuge sollten sicher aufbewahrt

werden. Sie sollten an einem trockenen und

hochgelegenen oder verschließbaren Ort

aufbewahrt werden, außerhalb der Reichweite von

Kindern und gebrechlichen Personen.

6. Werkzeuge sollten nicht mit übermäßiger Gewalt

verwendet werden. Ihre Leistung ist besser und

sicherer, wenn sie mit der vorgeschriebenen

Geschwindigkeit verwendet werden.

7. Nur die korrekten Werkzeuge verwenden. Niemals

ein kleineres Werkzeug oder Zusatzgerat für

Arbeiten verwenden, die Hochleistungsgerate

erfordern. Nur Werkzeuge verwenden, die dem

Verwendungszweck entsprechen, d.h. niemals eine

Kreissäge zum Sägen von Ästen oder Baum-

stämmen verwenden.

8. Die richtige Kleidung tragen. Keine lose Kleidung

oder Schmuck tragen, da sich lose Kleidungsstücke

in den bewegenden Teilen verfangen können. Bei

Arbeiten im Freien sollten Gummihandschuhe und

rutschfeste Schuhe getragen werden. Tragen Sie

eine schützende Haarabdeckung, um langes Haar

zurückzuhalten.

9. Es sollte eine Sicherheitsbrille getragen werden.

Bei Arbeiten mit Staubentwicklung sollte eine

Gesichtsoder Staubmaske getragen werden.

10. Schließen Sie eine Staubabsaugvorrichtung an.

Sägen mit dieser Verbundsäge kann eine

beträchtliche Menge Staub aus dem Auslass am

fixierten Schutz verursachen.

(Staubmaterial: Holz oder Aluminium)

Wenn Vorrichtungen für den Anschluß von

Staubabsaug- und -sammelvorrichtungen

vorhanden sind, so stellen Sie sicher, daß diese

angeschlossen sind und richtig verwendet werden.

11. Niemals das Kabel mißbrauchen. Ein Werkzeug

niemals am Kabel tragen oder bei Abtrennung

von der Steckdose das Kabel harausreißen. Das

Kabel sollte gegen Hitze, Öl und scharfe Kanten

geschützt werden.

12. Den Arbeitsplatz gut absichern. Zwingen oder einen

Schraubstock zur Befestigung des Werkstücks

verwenden. Das ist sicherer als die Benutzung der

Hände und macht beide Hände zur Bedienung des

Werkzeugs frei.

13. Sich niemals weit überbeugen. Immer einen festen

Stand und ein sicheres Gleichgewicht bewahren.

14. Die Werkzeuge sollten sorgfältig behandelt werden.

Für einen einwandfreien und sicheren Betrieb sollten

sie stets scharf sein und saubergehalten werden.

Die Anleitungen für schmierung und Austausch

des Zuehörs unbedingt einhalten. Die Kabel der

Geräte regelmäßig überprüfen und bei

Beschädigung durch eine autorisierte

Kundendienststelle reparieren lassen. Ebenfalls die

Verlägerungskabel regelmäßig überprüfen und bei

Beschadigung auswechseln. Die Handgriffe sollten

stets trocken und sauber sein, sowie keine Öl- oder

Schmierfett stellen aufweisen.

15. Werkzeuge vom Netz trennen, wenn sie nicht

benutzt werden, vor Wartungsarbeiten und beim

Austausch von Zubehörteilen wie z.B. Blätter,

Bohrer und Messer.

16. Alle Stellkeile und Schraubenschlüssel entfernen.

Vor Einschaltung des Gerätes darauf achten, daß

alle Stellkeile und Schraubenschlüssel entfernt

worden sind.

17. Ein unbeabsichtigtes Einschalten sollte vermieden

werden. Niemals ein angeschlossenes Werkzeug

mit dem Finger am Schalter tragen. Vor Anschluß

überprüfen, ob das Gerät ausgeschaltet ist.

18. Im Freien ein Verlängerungskabel verwenden. Nur

ein Verlängerungskabel verwenden, das für die

Verwendung im Freien markiert ist.

19. Den Arbeitsvorgang immer unter Kontrolle haben.

Das Gerät niemals in einem abgespannten Zustand

verwenden.

20. Beschädigte Teile überprüfen. Vor Benutzung des

Werkzeugs sollten beschädigte Teile oder

Schutzvorrichtungen sorgfältig überprüft werden,

um festzustellen, ob sie einwandfrei funktionieren

und die vorgesehene Funktion erfüllen,

Ausrichtung, Verbindungen sowie Anbringung sich

bewegender Teile überprüfen. Ebenfalls

uberprufen, ob Teile gebrochen sind. Teile oder

Schutzvorrichtungen, die beschädigt sind, sollten,

wenn in dieser Bedienungsanleitung nichts anderes

erwähnt ist, durch eine autorisierte

Kundendienststelle ausge wechselt oder repariert

werden. Dasselbe gilt für defekte Schalter. Wenn

sich das Werkzeug nicht mit dem Schalter einoder

ausschalten läßt, sollte das Werkzeug nicht

verwendet werden.

21. Warnung

Die Verwendung von anderem Zubehör oder

anderen Zusätzen als in dieser Bedienungs-

anleitung empfohlen kann das Risiko einer

Körperverletzung einschließen.

22. Lassen Sie Ihr Werkzeug durch qualifiziertes Personal

reparieren.

Dieses Elektrowerkzeug entspricht den zutreffenden

Sicherheitsanforderungen. Reparaturen sollten nur von

qualifiziertem Personal unter Verwendung von

Originalersatzteilen durchgeführt werden, da sonst

beträchtliche Gefahr für den Benutzer auftreten kann.

02Ger_C10FCH2_WE_7L 3/11/09, 9:5219

La page charge ...

Hitachi C 10FCE2 Le manuel du propriétaire

Marque: Hitachi

Modèle: C 10FCE2

Catégorie: Scies à onglet

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: Hitachi C 10FCE2 Manuale del proprietario
español: Hitachi C 10FCE2 El manual del propietario
Deutsch: Hitachi C 10FCE2 Bedienungsanleitung
Nederlands: Hitachi C 10FCE2 de handleiding
português: Hitachi C 10FCE2 Manual do proprietário

Hitachi C 10FCE2 Le manuel du propriétaire

Ce manuel convient également à

Hitachi C 10FCE2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents