WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
1
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5812
WARNING
IMPORTANT: NEVER attempt to do any work without shutting off the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL listing of this fixture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación UL esta lámpara.
5812
This instruction apply to the model(s) below:
*Note: WAC Smart Transformer is required to power the fixture. (sold separately)
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
2
Mounting Stake
Qty: 1pcs
Outdoor Rated Wire Nut
Qty: 2pcs
Hex Key
Qty: 1pcs
Adjustable Shroud
Qty: 1pc
MOUNTING ACCESSORIES
Step 1: Determining the location
1. Make sure your main power is off.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood. Hammer untill
the bottom of the stake flange is flush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the stake flange is flush with the ground.
Fill the rest of the hole with the removed soil and pack it tight
to secure the stake.
4. Screw the fixture onto the stake provided, leading the wire from
the fixture through the wire slot in the stake.
Step 2: Wiring the Fixture
*Note: WAC Smart Transformer is required to power the fixture.
(sold separately)
5. Cut the power supply wire from the transformer at the location
of the fixture.
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches is separated.
7. Strip off ½ inch of the insulating material from each wire and
connect one to each of the wires from the fixture using the
outdoor rated wire nuts provided.
Hammer
Wood
Mounting Stake
Soil
WAC SmartTransformer
To Next Fixture
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5812
Wall Wash Light
Wire Slot
Fixture Wires
Mounting Stake
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
3
Step 3: Installing the Fixture
8. Screw the fixture onto the stake provided, leading the wire from
the fixture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench. When finish
burying the wires, close the trench.
10. Repeat steps for other fixtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the fixtures
light up.
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint screw and adjust the head of the fixture
to the desired direction before retightening the screw.
13. Rotating: Loosen the mounting knob and rotate the fixture to
the desired position before retightening the knob.
Note: To install multiple fixtures, follow diagram above.
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5812
Runs to
the next
fixture
WAC Smart Transformer
Tilting
Joint Screw
Locking Nut
Rotating
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
4
Step 5: Beam Angle Adjustment:
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5812
1. Note the three pre-determined beam angles on the beam angle
changing dial.
2. Use the provided Hex Key to slightly loosen the set screw one or
two turns. Do not remove set screw from the fixture.
CAUTION: Do not remove set screw from the fixture. It should only
be removed from the fixture for servicing. Consult factory
for service instruction.
3. Hold the fixture body and rotate the dial until the Set screw is
aligned with the desired beam angle. This beam angle may be
one of the pre-determined markings or any number in between.
CAUTION: Keep the arrow marking on the fixture body between the
beam angle range.
4. Tighten the set screw until it stops. Do not over tighten.
Hex Key
Beam Changing Dial
Set Screw
STEP 6: Shroud Adjustment:
1. Loosen the thumb screw on the shroud.
2. Rotate the shroud until it is in the desired position to properly cut
off glare.
3. Retighten the thumb screw to lock the shroud in place.
Thumb Screw
Shroud
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
5
ACCESSORIES
I. Surface Mount Accessory
The surface mount accessory is used to mount the fixture to a hard
surface like wood or cement or as alternative to the mounting stake.
Installation: Mount the accessory to a hard surface using No. 10 Philips
head screws that are at least half an inch long. If mounting on concrete
or something similar, first use a plastic anchor sized for No. 10 screws.
If mounting on a soft surface first attach the included spikes.
Create a route underneath the accessory for your wire to travel through.
Lead your wire through the created route and screw your fixture onto
the surface mount accessory.
II. Tree Mount Accessory:
The tree mount accessory is a way for fixtures to be mounted on
the trunk or a branch of a tree while minimizing damage to the tree.
Installation: Mark the screw hole locations at the point of installation.
Thread one hex nut from flat side of wood screw bolt until end of
threaded. Use a wrench to screw the bolt into the tree until the
unthreaded portion of the bolt meets the surface of the tree.
(Do this for all three bolts.) Place the tree mount bracket onto the bolts
and secure it using additional hex nuts. Attach light fixture and lead wire
through the bracket. Place all wire nuts into the tree mount bracket.
III. Extension Accessory
Using extension rods and rod joiners, fixtures can be mounted
away from a surface in any desired direction.
Rods come in 5 sizes: 4 inches, 8 inches, 12 inches, 18 inches, and
24 inches. These rods can be connected via either straight or
90 degree rod joiners.
Installation: Screw in a rod joiner into your mounting accessory.
Screw an extension rod to the other side of the rod joiner.
Continue to use rod joiners and extension rods until the fixture is
in the desired position.
No. 10 Tapping Screw
Surface Mount
Accessory
Removable Spike
Tree Mount BracketHexnutWood Screw Bolt
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5812
Fixture
Extension Rods
90
Rod Angle
Rod Joiners
Mounting Stake
-
1
-
2
-
3
-
4
-
5
dans d''autres langues
Documents connexes
-
WAC Lighting 5611 Mode d'emploi
-
-
-
-
-
-
-
-
-