RPAA1, B1, C1 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!
It is the installer’s responsibility to make sure all components
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the RPAX1 does not exceed 50 lbs
(22.68 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: The RPAX1 mounts are designed to be
mounted to a 1-1/2" NPT or NPSM following ANSI/ASME
B1.20.1 (Schedule 40, 0.154" minimum thickness steel or
aluminum-ASTM B221) threaded extension column.
NOTE: RPAA1, RPAB1 and RPAC1 models are included in
these installation instructions. Throughout these
instructions "RPAX1" is used to designate all of the
models covered by these instructions.
--SAVE THESE INSTRUCTIONS--
Installation Instructions RPAA1, B1, C1
3
DIMENSIONS
4.02
102.0
4° ROLL
ADJUST
12.31
312.7
6.11
155.1
27° YAW
ADJUST
1.50" DIA NPT
3.73
94.8
25° PITCH
ADJUST
DIMENSIONS: INCHES
[MILLIMETERS]
RPAA1, B1, C1 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions RPAA1, B1, C1
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
3/32" (included)
5/32" (included)
R (4)
S (1)
5/32" U (4) V (4)
T (8)
Q (1)
[RPAX1]
[security box leg]
[spacer] [washer] [adhesive washer]
A (4)
#10-24 x 1/4"
B (4)
M3 x 10mm
C (4)
M4 x 10mm
D (4)
M5 x 12mm
E (4)
M6 x 12mm
F (4)
1/4-20 x 1/2"
G (4)
M2.5 x 10mm
H (4)
M3 x 10mm
J (4)
M4 x 10mm
K (4)
M5 x 12mm
L (4)
M6 x 12mm
O (1)
3/32"
M (4)
M4
N (4)
M6
P (4)
[thumb nut]
RPAA1, B1, C1 Installation Instructions
6
PREPARATION
Locate Mounting Site
WARNING: IMPROPER INSTALLATION MAY LEAD TO
PROJECTOR MOUNT FALLING CAUSING SEVERE
PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is
the installers responsibility to make certain the structure to
which the projector mount is being mounted is capable of
supporting five times the weight of the projector mount and all
attached equipment. Reinforce the structure as required
before installing the projector mount.
1. Determine required position of the RPAX1 projector mount.
2. Determine required distance of the projector mount from the
screen using the projector specifications.
INSTALLATION
Installing RPAX1 Outer Sleeve to Threaded Pipe
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
IMPORTANT ! : These installation instructions assume
that a 1-1/2" NPT or NPSM (Schedule 40, 0.154"
minimum thickness steel or aluminum - ASTM B221)
threaded extension column (not included) has been
properly installed (with a minimum of four threads
engaged) and is in place.
Figure 1
1. Install ceiling plate and extension accessories following
installation instruction provided by manufacturer.
2. Remove drawer from RPAX1 outer sleeve. (See Figure 1)
3. Loosen security screw on bottom of RPAX1 sleeve until set
screw is fully exposed. (See Figure 2)
Figure 2
4. Align RPAX1 outer sleeve with end of NTP pipe. (See
Figure 3)
5. Thread RPAX1 sleeve up onto pipe by turning clockwise
until hand tight. (See Figure 3)
Figure 3
2
Security
Screw
3
1
4
5
Installation Instructions RPAA1, B1, C1
7
6. Turn RPAX1 sleeve clockwise or counterclockwise until the
front of the RPAX1 is facing target. (See Figure 4)
Figure 4
7. Tighten set screw. (See Figure 4)
8. Tighten security screw until set screw cannot be seen from
set screw access hole. (See Figure 5)
Figure 5
Attaching Projector Security Legs
CAUTION: Using screws of improper length may damage
your projector! Proper screws will have adequate thread
engagement without contacting the bottom of projector
mounting holes.
1. Attach the projector security legs (R) to the projector, using
the correct size screws (A-L) and washers (M or N) for your
specific projector. (See Figure 6)
Figure 6
2. Add washers (U) to the projector security legs (R). Add
spacers (T) as necessary to the projector security legs (R).
(See Figure 7)
Figure 7
6
7
set
screw
8
security
screw
(A-L) x 4
(M) or (N) x 4
(R) x 4
Projector
or
8
(T) x 4
(U) x 4
2
(R) x 4
RPAA1, B1, C1 Installation Instructions
8
Attaching Projector to Security Mount Drawer
1. Align projector and security mount drawer so that the
projector is oriented correctly.
2. Remove the paper backing from the adhesive washers (V)
and attach projector to drawer using adhesive washers (V)
and thumb nuts (P) over the security legs (R). (See Figure 8)
Figure 8
3. Slide the security mount drawer into the RPAX1 outer
sleeve. (See Figure 9)
Figure 9
WARNING: Failure to lock RPAX1 can result in serious
personal injury or damage to equipment! Lock RPAX1
BEFORE aligning or adjusting the projector. RPAX1 MUST
be locked when it is loaded.
4. Lock the RPAX1. (See Figure 10)
Figure 10
Aligning Projector
The RPAX1 may be adjusted for vertical elevation (pitch),
horizontal tilt (roll), and rotation (yaw).
Pitch
Adjust pitch using the adjustment screws on the end of the
adjustment plate. (See Figure 11)
1. Loosen the pitch adjustment screws.
2. Adjust projector angle to desired pitch.
3. Tighten pitch adjustment screws.
Roll
Adjust roll using the two adjustment screws on the back of the
adjustment plate. (See Figure 11)
4. Loosen the two roll adjustment screws.
5. Adjust projector to desired roll.
6. Tighten roll adjustment screws.
Figure 11
(P) x 4
(V) x 4
(R) x 4
Projector
2
Projector
Security
Mount
Drawer
RPAX1
Outer
Sleeve
3
RPAX1
Lock
pitch adjustment screws
roll adjustment screws
456123
5
2
Installation Instructions RPAA1, B1, C1
9
Yaw
1. Loosen yaw adjustment screw. (See Figure 12)
2. Adjust mount to desired yaw. (See Figure 12)
3. Tighten yaw adjustment screw. (See Figure 12)
Figure 12
12 3
2
RPAA1, B1, C1 Installation Instructions
10
Installation Instructions RPAA1, B1, C1
11
RPAA1, B1, C1 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002525 Rev00
2014 Milestone AV Technologies
www.chiefmfg.com
03/14
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Chief RPAC1W Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief RPAC1W Installation guide