Smart Station
Model 7590
What’s Included in the Box
▪ Device
▪ USB-C Cable
Operation Instructions
1. Power On: On the
right side of the
Smart Station, hold
circle power button
down for 3 seconds.
2.
PowerO: On the right side of the Smart Station, hold
circle power button down for 2 seconds. Two options
then pop-up on the screen to either Power O or Restart.
3. Charging: Plug USB-C cable into bottom of device and
then into power source
4. Connecting to a Module: Power on module by holding
down the circle on the left for 1 second. A blue LED
light will start to blink indicating Bluetooth® is on.
- The module will appear in the list on the Smart Station.
If not, hit Refresh.
- Press desired module on screen to connect to
Smart Station. A green check mark indicates a
successful connection.
- Press Done
Now you’re ready to take measurements.
The OmniTrak™ Smart Station can be used in conjunction
with any OmniTrak™ Module to provide immediate feedback
as to the conditions in the immediate area. Take measurements,
create reports, and analyze data provided to help improve
conditions. This instrument is a handheld device, not to be
worn on the body, or near an individual’s head.
Dispose of battery in accordance with local rules
and regulations.
Smart Station
Model 7590
SpecicationsSpecications
AC and DC Power Requirements
AC/DC Power SupplyAC/DC Power Supply 100 to 240VAC, 100 to 240VAC,
50/60 Hz, 0.3A50/60 Hz, 0.3A
Device Input PowerDevice Input Power 5 VDC,10W 5 VDC,10W
2A, 10W2A, 10W
Environmental/Installation Requirements
Maximum AltitudeMaximum Altitude 3000 meters (10,000 feet)3000 meters (10,000 feet)
Pollution DegreePollution Degree 22
Installation CategoryInstallation Category II
Operating TemperatureOperating Temperature 5°C to 40°C5°C to 40°C
Storage TemperatureStorage Temperature -20°C to 60°C-20°C to 60°C
HumidityHumidity 0% - 95% 0% - 95%
(non-condensing)(non-condensing)
Compliance
FCC ID: 2A22JOTSTATIONFCC ID: 2A22JOTSTATION IC ID: 28101-OTSTATIONIC ID: 28101-OTSTATION
This device complies with part 15 of the FCC Rules. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 1. This device may not cause harmful interference.
2. This device must accept any interference 2. This device must accept any interference
received, including interference that may received, including interference that may
cause undesired operation.cause undesired operation.
Per FCC 15.21 Changes or modications not expressly Per FCC 15.21 Changes or modications not expressly
approved by TSI will void the product warranty and may approved by TSI will void the product warranty and may
void the user’s authority to operate the equipment.void the user’s authority to operate the equipment.
This device contains license-exempt transmitter(s)/This device contains license-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science receiver(s) that comply with Innovation, Science
and Economic Development Canada’s license- and Economic Development Canada’s license-
exempt RSS(s). Operation is subject to the exempt RSS(s). Operation is subject to the
following two conditions:following two conditions:
1. This device may not cause interference.1. This device may not cause interference.
2. This device must accept any interference, including 2. This device must accept any interference, including
interference that may cause undesired operation interference that may cause undesired operation
of the device.of the device.
Le présent appareil est conforme aux CNR d’Industrie Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux de licence. L’exploitation est autorisée aux deux
conditions suivantes: conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et 1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage 2. l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.susceptible d’en compromettre le fonctionnement.
To satisfy RF exposure requirements, this device and its To satisfy RF exposure requirements, this device and its
antenna may be operated near a persons body and the antenna may be operated near a persons body and the
extremities, but must be operated with a separation distance extremities, but must be operated with a separation distance
of at least 20 cm from all person’s head.of at least 20 cm from all person’s head.
Pour satisfaire aux exigences d’exposition RF, cet appareil Pour satisfaire aux exigences d’exposition RF, cet appareil
et son antenne peuvent être utilisés à proximité du corps et et son antenne peuvent être utilisés à proximité du corps et
des extrémités d’une personne, mais doivent être utilisés des extrémités d’une personne, mais doivent être utilisés
avec une distance de séparation d’au moins 20 cm de avec une distance de séparation d’au moins 20 cm de
la tête de toute personne. la tête de toute personne.
4420176118
TSI Incorporated
- Visit our website www.tsi.com for more information.
USA Tel: +1 800 874 2811
UK Tel: +44 149 4 459200
France Tel: +33 1 41 19 21 99
Germany Tel: +49 241 523030
India Tel: +91 80 67877200
China Tel: +86 10 8219 7688
Singapore Tel: +65 6595 6388
Printed in U.S.A.
P/N 5003016 Rev B
©2023 TSI Incorporated
Specications are subject to change without notice.
Wi-Fi is a registered trademark of Wi-Fi Alliance®.
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc.
TSI, and the TSI logo are registered trademarks of TSI Incorporated
in the United States and may be protected under other country’s
trademark registrations.
Smart Station
Model 7590
LASER WARNING
▪ OmniTrak™ Modules are Class 1 laser-based instruments.
▪ During normal operation, you will not be exposed to laserradiation.
▪ DO NOT open the OmniTrak™ Module when it is poweredON.
▪ You will not be exposed to the laser radiation when the OmniTrak™ Module is disassembled.
▪ The PM sensor has a laser inside it. DO NOT open the PM sensor inside OmniTrak Module
when the OmniTrak Module is powered.
AVERTISSEMENT LASER
▪ Les modules OmniTrak™ sont des instruments à base de laser de classe 1.
▪ Pendant le fonctionnement normal, vous ne serez pas exposé au rayonnement laser.
▪ N’ouvrez PAS le module OmniTrak™ lorsqu’il est sous tension.
▪ Vous ne serez pas exposé au rayonnement laser lorsque le module OmniTrak™ est démonté.
▪ Le capteur PM contient un laser. NE PAS ouvrir le capteur PM à l’intérieur du module OmniTrak
lorsque ce dernier est alimenté.
WARNING
▪ DO NOT attempt to replace the battery in this instrument.
▪ DO NOT abuse the battery in any way as the battery may rupture or catchre.
▪ DO NOT use a substitute or non-rechargeable battery in this instrument.
▪ DO NOT short-circuit, incinerate, dismantle or mutilate Lithium ion batteries
▪ DO NOT expose to water or heat.
▪ DO NOT use any battery which shows signs of damage, such as bulging, swelling,
a swollen plastic wrap, liquid in the plastic wrap, etc.
-
1
-
2
-
3
dans d''autres langues
- English: tsi 7590 User manual
Documents connexes
Autres documents
-
Stanley STHT77366 Manuel utilisateur
-
Samsung NP400B2YI Manuel utilisateur
-
Ingenico iSMP4 Manuel utilisateur
-
Sony SVE14A15FBS Safety guide
-
-
Sony SVP13227CBS Safety guide
-
-
-