Axis P3384-V Manuel utilisateur

ENGLISH DEUTSCH ITALIANO ESPAÑOL

INSTALLATION GUIDE

FRANÇAIS

AXIS P33 Network Camera Series

AXIS P3346 Network Camera

AXIS P3346-V Network Camera

AXIS P3367-V Network Camera

AXIS P3384-V Network Camera

Legal Considerations

Video and audio surveillance can be prohibited by laws

that vary from country to country. Check the laws in

your local region before using this product for

surveillance purposes.

This product includes one (1) H.264 decoder license. To

purchase further licenses, contact your reseller.

Electromagnetic Compatibility (EMC)

This equipment has been designed and tested to fulfill

applicable standards for:

• Radio frequency emission when installed according to

the instructions and used in its intended environment.

• Immunity to electrical and electromagnetic

phenomena when installed according to the

instructions and used in its intended environment.

USA - This equipment has been tested using a shielded

network cable (STP) and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Canada - This Class B digital apparatus complies with

Canadian ICES-003.

Europe - This digital equipment fulfills the

requirements for RF emission according to the Class B

limit of EN 55022.This product fulfills the requirements

for immunity according to EN 55024 residential and

commercial environments.

Australia - This digital equipment fulfills the

requirements for RF emission according to the Class B

limit of AS/NZS CISPR 22.

Japan - B

Korea -

ࢇ̛̛Еɼࢽࡈ%̗ࢷ࢕ળࢶଢ̛̛Ի۰

࣯Իɼࢽ߾۰یࡈଜЕʨࡶּࢶࡳԻଜֲֻҘ

एࠇ߾۰یࡈଟܹ࢑ݡТЬ

Safety

This product complies with EN/IEC/UL 60950-1, Safety

of Information Technology Equipment.

Equipment Modifications

This equipment must be installed and used in strict

accordance with the instructions given in the user

documentation. This equipment contains no

user-serviceable components. Unauthorized equipment

changes or modifications will invalidate all applicable

regulatory certifications and approvals.

Liability

Every care has been taken in the preparation of this

document. Please inform your local Axis office of any

inaccuracies or omissions. Axis Communications AB

cannot be held responsible for any technical or

typographical errors and reserves the right to make

changes to the product and documentation without

prior notice. Axis Communications AB makes no

warranty of any kind with regard to the material

contained within this document, including, but not

limited to, the implied warranties of merchantability

and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible

for incidental or consequential damages in connection

with the furnishing, performance or use of this material.

RoHS

This product complies with both the European

RoHS directive, 2002/95/EC, and the Chinese

RoHS regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member

states.

The WEEE marking on this product (see right) or its

documentation indicates that the product must not be

disposed of together with household waste. To prevent

possible harm to human health and/or the environment,

the product must be disposed of in an approved and

environmentally safe recycling process. For further

information on how to dispose of this product correctly,

contact the product supplier, or the local authority

responsible for waste disposal in your area.

Business users should contact the product supplier for

information on how to dispose of this product correctly.

This product should not be mixed with other commercial

waste. For more information, visit

www.axis.com/techsup/commercial waste

Support

Should you require any technical assistance, please

contact your Axis reseller. If your questions cannot be

answered immediately, your reseller will forward your

queries through the appropriate channels to ensure a

rapid response. If you are connected to the Internet, you

can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support by logging in to your

private support area.

ENGLISH

Safeguards

Please read through this Installation Guide carefully before installing the Axis product. Keep the

Installation Guide for further reference.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure. Do not install the

product on unstable brackets, unstable or vibrating surfaces or walls, since this could cause

damage to the product.

• Only use applicable tools when installing the Axis product; excessive force could cause

damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Use only accessories that comply with technical specification of the product. These can be

provided by Axis or a third party.

• Use only spare parts provided by or recommended by Axis.

• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for ser-

vice matters.

• This Axis product shall be used in compliance with local laws and regulations.

• To use this Axis product outdoors, it shall be installed in an approved outdoor housing.

• The Axis product should be installed by a trained professional. Observe relevant national

and local regulations for the installation.

Transportation

• Keep the protective packaging. When transporting the Axis product, the protective packag-

ing shall be replaced in its original position.

• When transporting the Axis product, use the original packaging or equivalent to prevent

damage to the product.

Battery Replacement

This Axis product uses a 3.0 V CR2032 lithium battery as the power supply for its internal real-time

clock (RTC). Under normal conditions this battery will last for a minimum of 5 years. Low battery

power affects the operation of the RTC, causing it to reset at every power-up. A log message will

appear when the battery needs replacing. The battery should not be replaced unless required!

If the battery does need replacing, please contact www.axis.com/techsup for assistance.

• Dispose of used batteries according to the manufacturer's instructions.

• Risk of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent battery, as recommended by the manufacturer.

Dome Cover Cleaning

• Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks

clean to the eye and never polish the surface. Excessive cleaning could damage the surface.

• For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free

neutral soap or detergent with water and a soft cloth. Rinse well with clean lukewarm

water. Dry with a soft cloth to prevent water spotting.

• Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning in direct

sunlight or at elevated temperatures.

AXIS P33/P33-V Network Camera Series Installation Guide Page 5

ENGLISH

AXIS P33/P33-V Network Camera Series

Installation Guide

This installation guide provides instructions for installing an AXIS P33/P33-V Network Camera

Series on your network. For all other aspects of using the product, please see the User’s Manual,

available on www.axis.com

Notes:

• Before you begin, make sure that the package contents, the required cables, tools,

and documentation are available. See Package contents below.

• This network camera is intended to operate with PoE; if not available use AXIS PoE Midspan 1 port (not

included).

Package contents

1. “Package contents” on page 5

2. “Hardware overview” on page 6

3. “Mount the camera” on page 7

4. “Assign an IP address” on page 9

5. “Set the password” on page 12

6. “Adjust the Lens” on page 15

7. “Complete the installation” on page 16

Item Models/variants/notes

Network camera AXIS P3346, AXIS P3346-V

AXIS P3367-V, AXIS P3384-V

Dome covers Clear transparent cover

Smoked transparent cover

Labels 2 adhesive serial no. labels

Mounting kit Resitorx screw driver, drill template, 2 screws and plugs,

terminal block connector

CD AXIS Network Video Product CD including product documentation,

installation tools and other software

Printed materials Installation Guide (this document)

Axis Warranty Document

AVHS Authentication key

Optional accessories Mounting bracket (region specific)

See www.axis.com for information on available accessories

Page 6 AXIS P33/P33-V Network Camera Series Installation Guide

Hardware overview

Dimension (HxW)

AXIS P3346 = 101 x 148 mm (4” x 5.83”)

AXIS P3346-V = 104 x 148 mm (4.07” x 5.83”)

AXIS P3367-V = 104 x 148 mm (4.07” x 5.83”)

AXIS P3384-V = 104 x 148 mm (4.07” x 5.83”)

Weight

AXIS P3346 = 490 g (1.1 lb)

AXIS P3346-V = 700 g (1.53 lb)

AXIS P3367-V = 700 g (1.53 lb)

AXIS P3384-V = 700 g (1.53 lb)

Network connector

LED indicators

Control button

I/O connector

(PoE)

Camera unit

Network cable

Dome cover

out Audio

in

SD memory card slot

Wall screws

Audio

Camera unit

Fan output

connector

Built-in microphone

AXIS P33/P33-V Network Camera Series Installation Guide Page 7

ENGLISH

Mount the camera

Note: Please remove the rubber band for transport-safety from the camera unit before you mount the

camera.

a. This Axis product can be mounted with the cables routed through or along the wall. This

product can also be fitted with a metal conduit for protecting the cabling when they are routed

along the wall. See the illustration that follows.

Mount camera directly onto the wall

1. Using the drill template drill 2 holes in the wall.

2. Route and connect all required cables. Required cables include the network cable and may

include external input/output devices and the active speaker/external microphone.

3. Attach the camera unit to the wall using screws and plugs appropriate for the wall material.

Mount camera using a mounting bracket (not included)

1. Using the drill template drill 2 holes in the wall.

2. Route all required cables through the wall and through the holes in the mounting bracket.

Required cables include the network cable and may include external input/output devices and

the active speaker/external microphone.

3. Attach the mounting bracket to the wall, using screws and plugs appropriate for the wall

material.

4. Connect cables.

5. Insert the SD memory card (optional).

6. Attach the camera unit to the mounting bracket using the two M4x8 screws provided.

Note: These instructions are for mounting the camera on a wall. The mounting bracket can also be used

for mounting the network camera to a junction box.

Page 8 AXIS P33/P33-V Network Camera Series Installation Guide

Network cable

M4x8 screw

Mounting bracket (Optional/not included)

Metal conduit (Optional/not included)

Wall screws

Network cable

AXIS P3346

AXIS P33/P33-V Network Camera Series Installation Guide Page 9

ENGLISH

Assign an IP address

The network camera is designed for use on an Ethernet network and requires an IP address for

access. Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. If your network does not have a DHCP server, the network camera will use

192.168.0.90 as the default IP address.

AXIS IP Utility and AXIS Camera Management are the recommended methods for setting an IP

address in Windows. These free applications are available on the Axis Network Video Product CD

supplied with this product, or they can be downloaded from www.axis.com/techsup Depending on

the number of cameras you wish to install, use the method that suits you best.

Notes:

• If you are unable to set the IP address, check for any firewall blocking the operation.

• See page 17 for other available methods for setting or discovering the IP address of the network camera,

in relation to other operating systems.

Method Recommended for Operating system

AXIS IP Utility

See page 10

Single camera

Small installations

Windows

AXIS Camera Management

See page 11

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows Vista

Window 7

Page 10 AXIS P33/P33-V Network Camera Series Installation Guide

AXIS IP Utility - single camera/ small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. You can also

manually set a static IP address through this application. AXIS IP Utility is available on the Axis

Network Video Product CD, or it can be downloaded from www.axis.com/techsup

Note that you must install the network camera on the same network segment (physical subnet) as

the computer running AXIS IP Utility.

Automatic discovery

1. Check that the network camera is connected to the network and that power has been applied.

2. Start AXIS IP Utility.

3. When AXIS P3346/AXIS P3346-V/AXIS P3367-V/AXIS P3384-V appears in the window,

double-click to open the camera’s home page.

4. See page 12 for instructions on how to set the password.

Set the IP address manually (optional)

1. Acquire an unused IP address on the same network segment your computer is connected to.

2. Select the network camera in the list.

3. Click the button Assign new IP address to selected device - and enter the serial number

and IP address for the network camera. The serial number is located on the product label.

4. Click the Assign button and follow on-screen instructions. Note that the camera must be

restarted within two minutes for the new IP address to be set.

5. Click the Home Page button to access the camera’s web pages.

6. See page 12 for instructions on how to set the password.

AXIS P33/P33-V Network Camera Series Installation Guide Page 11

ENGLISH

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show connection

status, manage firmware upgrades and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the camera appears in the window, right-click the link

and select Live View Home Page.

3. See page 12 for instructions on how to set the password.

Assign an IP address in a single device

1. Select AXIS P3346/AXIS P3346-V/AXIS P3367-V/AXIS P3384-V

in AXIS Camera Management and click the Assign IP button

.

2. Select Assign the following IP address and enter the IP

address, the subnet mask, and default router the device will

use.

3. Click OK.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of assigning IP

addresses to multiple devices, by suggesting IP addresses from a

specified range.

1. Select the devices you wish to configure (different models can be

selected) and click the Assign IP button .

2. Select Assign the following IP address range and enter the range

of IP addresses, the subnet mask, and default router the devices will use.

3. Click the OK button.

Page 12 AXIS P33/P33-V Network Camera Series Installation Guide

Set the password

To gain access to the product, the password for the default administrator user root must be set. This

is done in the Configure Root Password dialog, which is displayed when the network camera is

accessed for the first time.

To prevent network eavesdropping when setting the root password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate.

To set the password via a standard HTTP connection, enter it in the Configure Root Password

window. To set the password via an encrypted HTTPS connection, follow these steps:

1. Click the Create self-signed certificate button.

2. Provide the requested information and click OK. The certificate is created and the password can

now be set securely. All traffic to and from the network camera is encrypted from this point on.

3. Enter a password and then re-enter to confirm the spelling. Click OK. The password has now

been configured.

4. To log in, enter the user name “root” in the dialog as requested.

Note: The default administrator user name root cannot be deleted.

5. Enter the password as set above, and click OK. If the password is lost, the network camera must

be reset to the factory default settings. See page 21.

If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream

in Internet Explorer. You will need administrator rights on the computer to do this.

Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as administrator.

Right-click the Internet Explorer icon and select Run as administrator.

To configure the password directly via an

unencrypted connection, enter the

password here.

To create an HTTPS connection, start by

clicking this button.

AXIS P33/P33-V Network Camera Series Installation Guide Page 13

ENGLISH

6. AXIS P3346-V/AXIS P3367-V:

The capture mode must be set the first time network

camera is accessed. Select the desired capture mode

from the drop-down list and click OK.

Note: The capture mode can be changed later from the prod-

uct’s web pages, but this will reset most other settings.

For more information, see the online help or User’s

Manual.

Power Line Frequency

Note: Only applicable to AXIS P3384-V.

Power line frequency is set the first time the Axis product is accessed and can only be changed by

resetting the product to factory default.

Select the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product. Selecting

the wrong frequency may cause image flicker if the product is used in fluorescent light

environments.

Note: When using 50 Hz, the maximum frame rate is limited to 25 fps.

Note: Power line frequency is different in different geographic regions. In the Americas, 60 Hz is usually

used; most other parts of the world use 50 Hz. Local variations may apply, always check with the

local authorities.

Page 14 AXIS P33/P33-V Network Camera Series Installation Guide

Access the video stream

The Live View page of the network camera is displayed with links to the setup tools which allow

you to customize the camera.

If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream

in Internet Explorer. You will need administrator rights on the computer to do this.

Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as an administrator.

Right-click the Internet Explorer icon and select Run as administrator.

AXIS P33/P33-V Network Camera Series Installation Guide Page 15

ENGLISH

Adjust the Lens

Open the Live View page in the web interface and make the following adjustments to the camera:

1. Loosen the locking screw and tilt adjustment screws.

2. Turn the lens (with the lens holder) to the desired position. Make sure the horizontal lines on

either side of the lens are aligned horizontally.

Note: Ensure that the mark on the lens cover, between the horizontal lines, is facing up.

3. Once satisfied, gently tighten the locking screw and tilt adjustment screws to secure the

camera’s position.

4. Open the Focus Adjustment page in the Web interface under Setup > Basic Setup > Focus &

Zoom, and follow the on-screen instructions. Use the image window to adjust the focus and

zoom. See the online help files for more information.

Note: Due to the dome’s refraction, the image may appear slightly out of focus once the dome has been

placed. To correct this go to the Focus Adjustment page in the Web interface under Setup > Basic

Setup > Focus & Zoom, and adjust the focus again.

Warning! Adjusting the focus and zoom manually can damage the lens.

Locking screw

Tilt adjustment screw Tilt adjustment screw

Horizontal line

Page 16 AXIS P33/P33-V Network Camera Series Installation Guide

Complete the installation

1. If the cables are routed along the wall, remove the side lid from the camera’s dome cover.

2. Rotate the black protective shield inside the dome casing to match the camera’s position.

3. Clean the dome with a dry soft cloth to remove dust and finger prints and use a blower to

remove dust from the lens.

4. Mount the dome casing using the supplied tamper-proof screws and screw driver. Now that the

dome is in place, check that the camera is properly focused.

The installation is now complete.

Side lid

Dome cover

Camera unit

Network cable

Dome cover

AXIS P33/P33-V Network Camera Series Installation Guide Page 17

ENGLISH

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address. All

methods are enabled by default, and all can be disabled.

AXIS Video Hosting System (AVHS)

The camera can also be connected to an AVHS service for hosted video. If you have subscribed to an

AVHS service, follow the instructions in the Service Provider’s Installation Guide. For more

information and help to find a local AVHS Service Provider, go to www.axis.com/hosting

The camera owner authentication key is supplied with this product. The key is associated with the

camera’s unique serial number (S/N) as shown on the top of the label.

Note: Save the key for future reference.

Use in operating

system

Notes

UPnP™

Windows When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Page 18 AXIS P33/P33-V Network Camera Series Installation Guide

Set the IP address with ARP/Ping

1. Acquire a free static IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the camera’s label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the network camera and then start/restart the

network camera, by disconnecting and reconnecting power. If PoE is used, start/restart the

network camera by disconnecting and then reconnecting the network cable.

5. Close the command prompt when you see ‘Reply from 192.168.0.125:...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on

your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Unit connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using shielded

cables is recommended.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from

a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system or an

active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo

connector must be used for the audio out.

SDHC memory card slot - The high capacity SD memory card can be used for local recording with

removable storage.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

AXIS P33/P33-V Network Camera Series Installation Guide Page 19

ENGLISH

I/O terminal connector - Used in applications for e.g. motion detection,

event triggering, time lapse recording and alarm notifications. In addition to

an auxiliary power and a GND pin, it provides the interface to:

• 1 transistor output - For connecting external devices such as

relays and LEDs. Connected devices can be activated by the

VAPIX® Application Programming Interface (API), by the output buttons on the Live

View page or by an Action Rule. The output will show as active (shown under System

Options > Ports & Devices) if the alarm device isactivated.

• 1 digital input - An alarm input for connecting devices that can toggle between an

open and closed circuit, for example: PIRs, door/window contacts, and glass break

detectors. When a signal is received the state changes and the input becomes active

(shown under System Options > Ports & Devices).

The following connection diagram gives an example of how to connect an auxiliary device to the

Fixed Dome Network Camera.

Function Pin Notes Specifications

GND 1 Ground

3.3V DC

Power

2 Can be used to power auxiliary equipment.

Note: This pin can only be used as power out.

Max. load = 50mA

Digital

Input

3 Connect to GND to activate, or leave floating (or

unconnected) to deactivate.

Min. input= - 40V DC

Max. input= + 40V DC

Digital

Output

4 Uses an open-drain NFET transistor with the source

connected to GND. If used with an external relay, a

diode must be connected in parallel with the load,

for protection against voltage transients.

Max. load = 100mA

Max voltage = + 40V DC

Pin1

Pin2

Pin3

Pin4

1

2

E.g. push button

3

4

3.3V

max. 50mA

D

S

G

Page 20 AXIS P33/P33-V Network Camera Series Installation Guide

LED indicators

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Amber Steady during startup, during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

La page charge ...

Axis P3384-V Manuel utilisateur

Axis P3384-V Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents