Tineco CL2011E FLOOR ONE S2 SERIES Smart Cordless Vacuum and Washer Manuel utilisateur

FLOOR ONE S2 SERIES

Smart Cordless Vacuum & Washer

Instruction Manual

Manual De Uso

Mode D’emploi

*Actual product may differ from illustration.

TINECO IS HERE TO HELP.

We’ll get back to you within 1 business day.

www.tineco.com

1-855-292-8864

Mon. - Fri. 9am - 6pm (CST)

EN

1

CONTENTS

Important Safety Instructions ...............................................................2

Specications ........................................................................................6

Overview ................................................................................................7

Assembly ...............................................................................................9

Operation ............................................................................................10

Maintenance .......................................................................................14

Troubleshooting ..................................................................................18

Warranty ..............................................................................................19

TINECO IS HERE TO HELP.

We’ll get back to you within 1 business day.

www.tineco.com

1-855-292-8864

Mon. - Fri. 9am - 6pm (CST)

EN

2

Important Safety Instructions

SAVE THESE INSTRUCTIONS

Household use only.

When using an electrical appliance, basic precautions should always be followed, including

the following:

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the

warnings and instructions may result in electric shock, re and/or serious injury.

WARNING – To reduce the risk of re, electric shock, or injury:

1. This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children should not play with the

appliance. Cleaning and user maintenance shall not be performed by children without

supervision.

2. The appliance is not to be used by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction.

3. Use only indoors, on non-carpeted oor surfaces such as vinyl, tile, sealed wood, etc.

Be careful not to run over loose objects or edges of area rugs. Stalling the brush may

result in premature belt failure.

4. Do not allow to be used as a toy. Close attention is necessary when used by or near

children, pets or plants.

5. Use only as described in this manual. Use only manufacturer’s recommended

attachments.

6. Do not use with a damaged cord or plug. If appliance has been dropped, damaged,

left outdoors, dropped into water, or is not working as it should, return it to a service

center.

7. Do not handle charger, including charger plug, and charger terminals with wet hands.

8. Do not put any object into openings. Do not use with any opening blocked; keep free

of dust, lint, hair, and anything that may reduce air ow.

9. Keep hair, loose clothing, ngers, and all parts of your body away from openings and

moving parts.

10. Use extra care when cleaning on stairs.

11. Do not use to pick up ammable or combustible liquids, such as gasoline, or use in

areas where they may be present.

12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot

ashes.

13. Do not use without lter.

14. Prevent unintentional activation. Ensure the switch is in the off-position before picking

up or carrying the appliance. Carrying the appliance with your nger on the switch or

energizing appliance that have the switch on invites accidents.

15. Always switch off the appliance before making any adjustments, changing accessories,

or storing the appliance. Such preventive safety measures reduce the risk of starting the

appliance accidentally.

EN

3

16. Recharge only with the charger specied by Tineco. A charger that is suitable for one

type of battery pack may create a risk of re when used with another battery pack.

17. Use appliances only with specically designated Tineco battery packs. Use of any other

battery packs may create a risk of injury and re.

18. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid comes into eye contact, seek

medical help. Liquid ejected from the battery may cause irritation or burns.

19. Do not use a battery pack or appliance that is damaged or modied. Damaged or

modied batteries may exhibit unpredictable behavior resulting in re, explosion or risk

of injury.

20. Do not expose a battery pack or appliance to re or excessive temperature. Exposure

to re or temperature above 266°F (130°C) may cause an explosion.

21. Follow all charging instructions and do not charge the battery pack or appliance

outside of the temperature range specied in the instructions. Charging improperly or

at temperatures outside of the specied range may damage the battery and increase

the risk of re.

22. Have servicing performed by a qualied repair person using only identical replacement

parts. This will ensure that the safety of the product is maintained.

23. This appliance contains battery cells that are non-replaceable. Do not modify or

attempt to repair the appliance or the battery pack except as indicated in the

instructions for use and care.

24. Always turn off this appliance before connecting or disconnecting the motorized

nozzle.

25. Do not charge or store the appliance outdoors or inside the car. Only charge, store or

use the battery in a dry indoor area where the temperature is higher than 39.2°F (4°C)

but lower than 104°F (40°C). The charger is for indoor use only.

26. Do not use to pick up ultrane particles, such as lime, cement, sawdust, gypsum

powder, or ashes.

27. Do not use to pick up sharp objects, such as metallic nails, pieces of glass, metal paper

clips, or pins.

28. Do not use to pick up hazardous material and chemicals, such as solvent, drain cleaner,

strong acids, or strong alkali.

29. Stop using immediately if the appliance is overheating, making unusual noises,

producing unusual odors, performing low suction, or leaks electricity.

30. Turn cleaner OFF and disconnect from electrical outlet for long-term storage.

31. Always clean the Dirty Water Tank after each use to avoid potential blockage, which

may lead to low suction power, motor overheating, or reduce the service life of the

appliance.

32. Store appropriately indoors in a dry place after use.

33. Do not place or submerge appliance in standing water or try to clean ooded areas.

34. All data and technical instructions of this manual are based on results from lab

tests of Tineco or designated third parties. The company reserves all rights for nal

explanations.

35. The plug must be removed from the socket-outlet before cleaning or maintaining the

appliance.

36. A hazard may occur if the appliance runs over the supply cord.

37. Do not use the appliance when the water depth is more than 5mm above the surface.

EN

4

38. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord

around sharp edges or corners. Do not run appliance over cord. Keep cord away from

heated surfaces.

39. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

Range of Usage

1. The cordless hard oor cleaner is to be used on indoor hard oors, such as vinyl, tile,

sealed wood, etc. Use on a rough surface may not get the best performance.

2. Keep your appliance away from heat sources, such as replace or heater, to avoid

casing deformation.

3. Do not use to pick up ammable or combustible liquids, ultrane particles, sharp

objects, hazardous material, chemicals or anything that is burning or smoking, as

described above.

About Cleaning Solution

1. A large amount of cleaning solution entering into the motor may cause damage to the

appliance.

2. Add solution as instructed in the Product Operation section. We recommend using the

provided cleaning solution. Do not use the product with acidic, alkaline solution, or any

substances harmful to the environment.

3. Keep out of the reach of children. Avoid contact with eyes and skin, otherwise, rinse

thoroughly with water. If irritation persist, seek medical advice. If product is swallowed

seek medical advice.

4. Dirty water and solution disposal should comply with local environmental regulations.

About the Appliance

1. Do not modify or attempt to repair the appliance except as indicated in the instructions

for operating and cleaning.

2. Charge the appliance with the Tineco adaptor. Input Voltage: AC 100-240V. Both high

and low voltages can damage the adaptor, appliance, or even cause danger to the user.

3. Use extra care when cleaning on stairs.

4. Ensure that the Power Switch is in the OFF-position before picking up or carrying

the appliance. Do not lay at or lean the appliance so as to prevent dirty water from

entering into the motor.

5. To avoid being tripped accidentally, please put away the appliance on the storage tray.

6. Always install the Dirty Water Tank and Clean Water Tank properly before use.

7. Do not allow the appliance or charger to get wet to avoid risk of re or injury caused by

a short circuit.

EN

5

TINECO/Floor One S2 Series

This appliance complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This appliance may not cause harmful interference, and (2) this appliance must accept

any interference received, including interference that may cause undesired operation.

TINECO INTELLIGENT, INC.

1700 WESTLAKE AVENUE N., SUITE 200, SEATTLE, WA, 98109, USA

WWW.TINECO.COM

1-855-292-8864

CAUTION: Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital appliance, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

(1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver.

(3) Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

(4) Consult the dealer or an experienced radio/TV technician for help.

EN

6

Specications

Product FLOOR ONE S2 SERIES

AC Input 100-240V~

Voltage 21.6V 4000mAh Lion

Rated Power 190 W

Running Time ≥35 mins

Charging Time ~5 hrs

Water Flow Rate 30~100ml per min

CWT Capacity 0.6L

DWT Capacity 0.5L

Waterproof IPX4

Only use the Tineco provided adaptor: KL-WA260080-A3 or YLS0241A-T260080.

Disposal

• The battery contains materials that are harmful to the environment and must be removed from the

appliance before it is discarded.

• When removing the battery, the appliance must be powered off.

• Batteries, chargers, accessories and packaging should be sorted for environmental friendly recycling.

Do not put them into re, water or soil. Do not dispose of batteries and chargers into household

waste!

• If battery leakage contacts skin or clothing, immediately ush with water to avoid irritation and seek

medical help.

EN

7

Overview

Note:

Accessories may vary between markets. If you require more accessories, please go to www.tineco.com

or store.tineco.com.

R

Q

P

S

A

B

J

L

C

M

D

K

N

E

F

G

H

IO

A. Self-cleaning Button

B. AUTO/MAX

C. Power On/Off

D. Digital Display

E. Clean Water Tank Release

F. Clean Water Tank Handle

G. Dirty Water Tank Release

H. Dirty Water Tank Handle

I. Brush Roller Cover Release

J. Tube

K. Clean Water Tank (CWT)

L. Dirty Water Tank (DWT)

M. Floater

N. Brush Roller Cover

O. Brush Roller

P. Deodorizing & Cleaning Solution

Q. Cleaning Tool

R. Adaptor

S. Storage Tray

EN

8

Digital Display

A. Self-cleaning Icon

B. Brush Roller Tangled Indicator

C. Dirt Monitoring Loop

(Blue to red according to the dirt

amount)

D. AUTO Mode

E. CWT Empty

F. Water Level

G. Tineco Logo

H. Battery Level Indicator

A B C D E F G H

EN

9

Assembly

How to Assemble/Disassemble

Note:

For water tank and brush assembly, please refer to “Operation” and “Maintenance”.

To assemble the handle, insert it into the

appliance until you hear a “Click”.

In the event that the handle need to be

disassembled, press the spring to release the

handle with a tool (like a screwdriver) and lift the

released handle from the appliance.

click

EN

10

Stop Working Start Again

Operation

Preparing for Use

Before rst use, please charge the appliance for 5 hours (refer to “Charging Instructions” for details).

* Based on results from Tineco lab tests. Lab temperature 39.2°F (4°C) ~ 104°F (40°C).

AUTO MAX

Tips:

• Solution mode/ Water Only mode:

Appliance starts with Solution mode by

default. Power on while the appliance is

upright, long-press

AUTO MAX

for 3s to switch

between the two modes.

• Switch to Water Only mode:

LED Loop: Red → Blue (use water only)

• Switch to Solution mode:

LED Loop: Blue → Red (use cleaning solution)

Press the button and the appliance will start in

AUTO mode by default. Press it again to turn off

the appliance. Switch between AUTO and MAX

mode by pressing the

AUTO MAX

button.

<142°

The appliance will stop working when put uprightly

and start running again when you recline.

* Do not recline more than 142° to protect against

water leakage.

Place the appliance on the storage tray

vertically after use.

Note:

• Do not vacuum foamed liquid.

• To vacuum water left on the surface, the appliance will switch off in 3 seconds after power off.

EN

11

Filling Clean Water Tank

MAX

Press the Clean Water Tank release button to

remove it from the appliance.

Open the tank cap, and ll with tap water to the

Max line. When deep cleaning is necessary, add

one bottle cap of solution to the CWT and tightly

close the cap.

②

①

click

Note:

Only use water under 140°F/60°C.

DO NOT USE HOT WATER.

Place the tank back into the appliance. You

should hear a “Click” if done correctly.

Charging Instructions

Please charge the appliance when the indicator is blinking.

1. To charge the appliance, connect the external charging cord

to the appliance and plug it into the wall outlet.

2. To avoid tripping hazards, please place the appliance on the

storage tray near a wall during charging.

Warning:

• Only charge the appliance with the adaptor supplied by Tineco.

• During long periods of not being used, the appliance must be charged once every 3 months for

optimal performance.

• Store indoors in a dry place. Do not expose the appliance to sunlight or freezing temperatures.

Recommended temperature range: 39.2°F (4°C) ~ 104°F (40°C).

EN

12

Cleaning Mode Selection

AUTO Mode

• In AUTO mode, the iLoop™ sensor automatically detects how dirty the oor is and applies the

appropriate amount of detergent and suction power.

• A red dirt monitoring loop indicates more dirt is detected, and a blue loop indicates less dirt is

detected. This mode automatically provides the best cleaning solution.

Clean: on Min

Power

Vary depending

on dirt amount

Heavy dirt: on

Max Power

MAX Mode

AUTO MAX

• In AUTO mode, press the AUTO/MAX button to enter MAX mode. The AUTO indicator on the

display will turn off.

• In Max mode, the appliance will apply max suction power and will spray water/solution for deeper

cleaning.

Note:

Keep sharp objects away from the digital display screen to avoid scratches and scrapes.

EN

13

Charging Time

• A full charge takes approximately 5 hours.

• Estimated data was obtained by a Tineco Laboratory using ambient temperatures between

39.2°F(4°C) to 104°F (40°C).

Indicator

When in Use

Battery level ≥ 10%: battery indicator will be illuminated.

Battery level < 10%: battery indicator will be blinking.

Off: no power detected or possible battery malfunction.

Solid red light: dirt sensor malfunction or blocked.

Indicator blinking: CWT is empty.

Indicator blinking: brush roller is not installed or has a blockage.

Indicator blinking: appliance is in need of self-cleaning.

During Charging

Tineco indicator: blinking.

Fully Charged

In 5 minutes: Tineco indicator illuminated.

After 5 minutes: all indicator lights turn off.

EN

14

Maintenance

Note:

• For optimal performance and to prevent odors, always clean and dry DWT, oater, lters, brush

roller, brush roller cover completely after each use.

• Please make sure each part is installed correctly or the appliance may not work properly.

• After maintenance, place the appliance on the storage tray vertically. Do not expose the appliance

to direct sunlight, and store it indoors in a dry place.

Main Body

AUTO MAX

To reduce the risk of injury, switch off before

performing maintenance.

Use a cloth to clean the surface with a neutral

detergent. The cloth should be dry to prevent

water from entering the appliance.

When LED loop illuminates red, remove Dirty

Water Tank, clean the dirt sensor with a damp

cloth or cleaning tool.

EN

15

Dirty Water Tank

• When dirty water reaches the Max line, the oater will block off the DWT and create a high pitched

sound indicating it’s time to switch off the appliance.

• Pull up the tank lid to empty the DWT. Rinse the inside of the DWT and place back into the

appliance.

Filter & Floater

If the lter and the oater have been blocked, rinse with water.

Remove the lter from the tank lid, remove the oater, and rinse both parts with water.

Dry Filter

Grasp recessed area on each side of the lter and pull upward. Rinse under running water and must be

completely dry before recombining with the lid of the DWT.

EN

16

Self-cleaning

1. Place the appliance on the storage tray and plug in.

Press the self-cleaning button and begin the process.

2. Once complete, the appliance will begin charging.

Clean the Dirty Water Tank after cleaning completed.

Note:

• Ensure the appliance is plugged in and the battery level

is >10%.

• Before self-cleaning cycle, please clean the DWT and

ensure the water level in the CWT exceeds 40%.

Brush Roller Cover

Grab the front handle while pressing the button

and pull upward to remove.

Rinse with water.

②

①

click

When replacing, always latch the brush cover into

place to avoid leakage.

EN

17

Brush Roller

Remove the brush roller by grabbing the brush

roller tab and pulling upward.

Remove the hair and debris wrapped around the

roller and rinse with water (brush roller tab can be

removed). Replace the brush roller back onto the

storage tray, and allow it to dry completely before

reinstalling.

Remove hair and debris from the brush roller

chamber and the opening with a tissue or a

damp cloth.

Replace the brush roller by inserting the brush

roller end into the right side of the holder, then

lock the pull tab into place by pressing downward.

Note:

To maintain high performance, replace the brush roller every 6 months.

EN

18

Troubleshooting

Problem Possible cause Solution

The appliance does not turn on Auto protection for overheating Restart after cooling down

The appliance has no power Charge the appliance

Weak suction

The dry lter is not installed,

or the dry lter is dirty

Install the dry lter or clean and

allow it to dry completely

Suction mouth is blocked Pull up the brush roller and

remove blockages

Brush roller tangled

indicator blinking

The brush roller is blocked Remove blockages

The brush roller is not

installed Install brush roller correctly

CWT empty indicator

blinking CWT is empty Rell CWT

All lights off in

operation Battery overheat or malfunction Cool the appliance down and

restart

Battery level indicator

blinking Low battery Charge the appliance, or restart

LED loop illuminates

red

Dirt sensor malfunction or

blocked

Remove blockages, clean the

debris channel, or restart

Self-cleaning icon

blinking Brush roller is dirty Start self-cleaning

Note:

If the above troubleshooting guide fails to provide a solution, please visit our website

www.tineco.com for further support.

La page charge ...

Tineco CL2011E FLOOR ONE S2 SERIES Smart Cordless Vacuum and Washer Manuel utilisateur

Tineco CL2011E FLOOR ONE S2 SERIES Smart Cordless Vacuum and Washer Manuel utilisateur

dans d''autres langues