Alpine KTX-PRS8 Guide d'installation

Catégorie
Kits de voiture
Taper
Guide d'installation

Ce manuel convient également à

Mobile
Media
Solutions
Perfect Fit
201
0-up
Toyota Prius {Excluding
C,
V and
models
with
Factory Navigation
or
JBL)
KTX-PRS8
Ford Trim
Panel
x
1
(Panel 7304)
Power Harness x
1
Steering
Wheel Remote
Control Module x
1
Left Bracket x 1
(Panel 7306)
Right Bracket x
1
(Panel 7305)
Introduction
This KTX-PRS8 Perfect Fit
installation
kit is
for
Select
201
0+
Toyota Prius.
Included are
all the
parts needed
to
install
your
Alpine INE-Z928HD
Audio Video Navigation system in
Select
201
0+
Toyota Prius. KTX-PRS8 Perfect Fit
installation kit
also includes
an
interface
module
that
allows
steering
wheel
remote
control
of
the
Alpine
system. Refer
to
the
individual
instruction sections
of
this
manual
to
remove your
vehicle's
factory radio and
assemble
the kit.
Caution!
Disconnect
your
vehicle's
negative
battery
terminal
before
the
installation
to
help
prevent
electrical
damage. We
recommend
the
use
of
a
digital
multimeter
to
check
vehicle
wiring.
Do
not
use
a
test
light!
A
test
light
or
grounded
wire
probe
can
cause
damage
to
the
vehicle's
computer
and/or
diagnostic
systems.
Avoid
all
factory
airbag
wiring.
Airbags
can
accidentally
deploy
causing
serious
injury
or
even
death.
Notes:
See
your
vehicle's
instructions
for
any
special tools
your
installation
might require.
Read
all instructions accompanying your car stereo for proper wiring and mounting
instructions.
1
Factory Stereo
Removal
1. Use a
Panel Removal Tool
to
unsnap trim
bezel
around shifter
unplug
and remove.
2. Use a Panel Removal Tool
to
unsnap the center
console/pocket surround
panel
and remove.
3. Use a
Panel Removal Tool
to
unsnap the push/start
trim
bezel,
(Do
not
unplug).
4.
Use a
Panel Removal Tool
to
unsnap the
stereo trim bezel, unplug and remove.
5. Extract
(4)
1
Omm
bolts
securing the stereo,
unplug
and remove.
6.
Use a Panel Removal Tool
to
unsnap the A/C
climate control assembly, unplug
and remove.
2
Mounting The Stereo
1.
Mount
brackets
to
INE-Z928HD with screws
supplied
with the radio.
3.
Use
(4)
1
Omm
bolts
(from step
5)
to
secure radio in dash.
Steering
Wheel Controls
Steering
Wheel Control
Operation
(when
vehicle
is equipped}
1.
Seekffrack
Up
2.
Source
3.
Seekffrack
Down
4.
Mute
5.
Volume Down
6.
Volume
Up
2.
Plug
in the
supplied radio harnesses, steering
wheel controls, and radio
replacement module.
Run
Bluetooth
mic, and
install
foot
brake and
parking brake wires.
3
Wiring Harness Diagram
To
Toyota Prius
Vehicle
Harness
To
Parking
Brake
{-)
Yellow/Blue
at
the parking brake
F====~
in drivers
kick
panel
To
aftermarket
amplifier
remote
turn on
To
Reverse
Trigger
Blue/White
{+).Use
only
with a Orange/White
back
up
camera
{+)
side
of
the reverse
light
Liability Disclaimer
To
Steering
Wheel
Remote
Control
Module
10A
To
Head Unit
INE-Z928HD
Audio
Video
Navigation
System
To
AuxIn
Due
to
changes in design and manufacturing that may
occur
with your specific vehicle, it
is important that you
do
not
rely solely on vehicle information contained in this
installation
manual, such as dash disassembly, wire harness, and codes.
Such
information should be
confirmed with the vehicle manufacturer. Alpine Electronics,
Inc. and its
affiliated
companies
is not responsible
for
damage that may occur
to
you
or
your automobile during the
installation
of
the Perfect Fit Kit.
If
you have any further questions, feel
free
to
contact Alpine Tech Support at
1-800-NAV-HELP.
ALPINE ELECTRONICS OF AMERICA, INC.,
19145 Gramercy Place, Torrance,
CA 90501, U.S.A
ALPINE ELECTRONICS OF
CANADA,
INC.,
777 Supertest Road, Toronto, Ontario M3J 2M9,
Canada
Do not send products
to
these addresses.
Call
the
toll
free number
or
visit the website
to
locate a service center.
4
-.-
--
--
PERFECT
'oQiu[J
~N
s
PERFECT
FIT™
INSTALLATION KIT
KIT
D'
INSTALLATION
PERFECT
FIT™
ALPINE
ELECTRONICS
OF
AMERICA,
INC.
www
.alpine.com
DRIVING MOBILE MEDIA SOLUTIONS
KTX-PRSS-5
2010-UP
TOYOTA PRIUS
INSTALLATION
KIT
(EXCLUDES PRIUS C
& V)
KTX-PRSS-5
2010-UP
TOYOTA PRIUS
INSTALLATION KIT
(EXCLUDES
PRIUS
C
&
V)
~
#/ff/ILPINE
®
Mobile
Media
Solutions
9
PERFECT SHAPE
AND
COLOR
MATCH
TO OEM DASH FOR FACTORY FIT
##MLPINE
®
INCLUDES ALPINE-TO-VEHICLE HARNESS FOR
PLUG-AND-PLAY INSTALLATION
INCLUDES RETAINING CLIPS
Mobile
Media
Solutions
INSTRUCTION
MANUAL
WITH STEP-BY-STEP INSTALLATION OF
ALL
COMPONENTS
CORRESPONDANCE PARFAITE
AVEC
LA
FORME ET COULEUR
DU
TABLEAU DE BORD
DE
L'EQUIPEMENTIER POUR
UN
ASPECT
SORTIE D'USINE
COMPREND UN HARNAIS POUR
CONNECTER
L'UNITE ALPINE
AU
VEHICULE POUR
UNE
INSTALLATION
PR~TE
A
L'EMPLOI
COMPREND LES CLIPS
DE
MAINTIEN
MANUEL
D'INSTRUCTIONS DETAILLANT L'INSTALLATION PAS
A
PAS
DE
TOUS LES COMPOSANTS
Alpine, Alpine Mobile
Media
Solutions,
Driving
Mobile
Media
Sol~.:~tions
are registered trademarks
of
Alpine Electronics, Inc.
Alpine, Alpine Mobile Media
Solutions,
Driving
Mobile
Media
Solutions
sont
des
marques deposees
d'Aipine Electronics,
Inc.
MADE
IN CHINA
FABRIQUE
EN
CHINE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Alpine KTX-PRS8 Guide d'installation

Catégorie
Kits de voiture
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues