Whirlpool CSP2860TQ Guide d'installation

INSTALLATION

INSTRUCTIONS

Commercial Stacked Dryer

Gas (120-Volt, 60-Hz)

or Electric

(120/240-Volt, 60-Hz)

www.whirlpoolcommerciallaundry.com

W10761037A

W10761038A – SP

INSTRUCTIONS

D’INSTALLATION

Sécheuse à usage

commercial superposée

à gaz (120 Volts, 60 Hz)

TABLE OF CONTENTS

Page

Dryer Safety ............................................................................. 2

Tools & Parts ........................................................................... 5

Dimensions/Clearances ........................................................ 6

Location Requirements ......................................................... 7

Gas Dryer Electrical Requirements ..................................... 8

Gas Requirements ................................................................. 9

Electric Dryer Electrical Requirements ............................. 10

Dryer Venting Requirements .............................................. 12

Gas Supply Connection ...................................................... 14

Installing Coin Slide and Coin Box ...................................... 16

Electric Dryer Electrical Connections ............................... 17

Leveling ................................................................................. 21

Complete Installation ........................................................... 22

Reversing Dryer Door Swing ............................................... 23

Changing to a 30- or 60-Minute Timing Cam ..................... 24

Maintenance Instructions .................................................... 25

If You Need Assistance ........................................................ 25

Warranty ............................................................................... 26

TABLE DES MATIÈRES

Page

Sécurité de la sécheuse ........................................................ 27

Outils et pièces ..................................................................... 30

Dimensions/Distances de dégagement ............................. 31

Exigences de l’emplacement ............................................... 32

Exigences électriques pour la sécheuse à gaz .................. 33

Exigences de gaz................................................................... 34

Exigences concernant l’évacuation de la sécheuse ......... 35

Raccordement à la canalisation de gaz ............................. 37

Installation de la glissière à monnaie

et de la caisse à monnaie .................................................... 39

Nivellement ............................................................................40

Achever l’installation ............................................................. 41

Inversion du sens d’ouverture de la porte ..........................42

Installation d’une came de minutage

de 30 ou 60 minutes ..............................................................43

Instructions d’entretien .........................................................44

Si vous avez besoin d’assistance ........................................44

Garantie ................................................................................. 45

Actual unit may or may not contain doors

with windows, depending on model.

Selon le modèle, le présent appareil

n’offre peut-être pas de hublot de porte.

2

DRYER SAFETY

■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer

smells gas. This information should be obtained from your gas supplier.

■ Post the following warning in a prominent location.

3

DRYER SAFETY

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

4

DRYER SAFETY

■ Clean dryer lint screen before or after each load.

■ Do not use this dryer without the lint screen in place.

■ Do not repair or replace any part of the dryer or attempt

any servicing unless specically recommended in this

Installation Instructions or in published user-repair

instructions that you understand and have the skills

to carry out.

■ Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

■ Do not use heat to dry articles containing foam rubber

or similarly textured rubber-like materials.

■ The nal part of a tumble dryer cycle occurs without heat

(cool-down cycle) to ensure that the articles are left at

a temperature that ensures that the items will not be

damaged.

■ WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated. (Avoids risk

of spontaneous combustion).

■ Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint,

dust, and dirt.

■ The interior of the dryer and dryer exhaust vent should

be cleaned periodically by qualied service personnel.

■ See “Electrical Requirements” section for grounding

instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic precautions, including

the following:

SAVE THESE INSTRUCTIONS

■ Read all instructions before using the dryer.

■ This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

■ WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear

the area. Contact the dryer owner immediately.

■ Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch re.

■ Do not dry articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other ammable, or explosive

substances as they give off vapors that could ignite

or explode.

■ Do not dry unwashed items in the dryer.

■ Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

■ Before the dryer is removed from service or discarded,

remove the doors to the dryer compartment.

■ Do not reach into the dryer if the drum is moving.

■ Do not open door while dryer is in operation. It will stop.

■ Do not install or store the dryer where it will be exposed

to the weather.

■ Do not tamper with controls.

5

Tools Needed:

8" (200 mm) 8" (200 mm) or 10" (250 mm) Flat-Blade Screwdriver Phillips Screwdriver

or 10" (250 mm) Adjustable Wrench

Pipe Wrench That Opens to 1" (25 mm)

Torx

®†

T-20 Security 1" (25 mm) Hex-Head 5⁄16" (8 mm) Socket Wrench Pliers (that open to

Screwdriver or Bit Socket Wrench 1

9

/

16

" [39 mm])

Level Utility Knife 1/4" (6 mm) Nut Driver 27" (686 mm)

Wood Block

Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound Putty Knife

(for installing new exhaust vent) Suitable for Gas Type

Flashlight (optional) 1" (25 mm) Ruler or Measuring Tape

Open-End Wrenches

TOOLS & PARTS

Parts Supplied:

10-32 x 5/16" Serrated Screws (4) Security Cotter Pins (2)

†® TORX and T-20 are registered trademarks of Acument Intellectual Properties, LLC.

6

DIMENSIONS/CLEARANCES

Dimensions

Clearances

Front View

Recessed Front View Recessed Side View

Side View Back View

7

Your dryer can be installed in a basement, laundry room,

or recessed area.

Companion appliance location requirements should also

be considered.

IMPORTANT:

■ Do not install or store the dryer where it will be exposed

to the weather. Proper installation is your responsibility.

■ This dryer must not be installed in a closet with a door.

You will need:

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■ A level oor with a maximum slope of 1" (25 mm) under

entire dryer. Installing the dryer on soft oor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

Dryer installation clearances

■ The location must be large enough to allow the dryer door

to be fully opened.

■ Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

■ Additional clearances might be required for wall, door,

and oor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

LOCATION REQUIREMENTS

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

■ Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

■ Make sure that lower edges of the cabinet, plus the back

and bottom sides of the dryer, are free of obstructions to

permit adequate clearance of air openings for combustion

air. See “Recessed Area Installation Instructions” below

for minimum spacing requirements.

Recessed Area Installation Instructions

This dryer may be installed in a recessed area. For recessed

area installations, minimum clearances can be found on the

warning label on the rear of the dryer or in “Dimensions/

Clearances.”

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes

and ordinances.

The dryer must be exhausted outdoors.

8

Gas Dryer Grounding

IMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA

70, latest edition, or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrical installer determine

that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■ Do not ground to a gas pipe.

■ Do not have a fuse in the neutral or ground circuit.

■ A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

■ Check with a qualied electrician if you are not sure

the dryer is properly grounded.

GAS DRYER ELECTRICAL REQUIREMENTS

9

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and

ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certied by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level

at the B.T.U. rating indicated on the model/serial plate. Burner

input adjustments are not required when the dryer is operated

up to this elevation.

When installed above 10,000 feet (3048 m), a four percent

(4%) reduction of the burner B.T.U. rating shown on the model/

serial plate is required for each 1,000 foot (305 m) increase in

elevation. For assistance when converting to other gas types

and/or installing above 10,000 feet (3048 m) elevation, contact

your local service company.

Gas Supply

GAS REQUIREMENTS

10

Electric Dryer GroundingIt is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

■ The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

■ A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch

Park, Quincy, MA 02269.

■ To supply the required 3 or 4 wire, single phase, 120/240

volt, 60 Hz., AC only electrical supply (or 3 or 4 wire,

120/208 volt electrical supply, if specied on the serial/

rating plate) on a separate 30-amp circuit, fused on both

sides of the line. A time delay fuse or circuit breaker is

recommended. Connect to an individual branch circuit.

Do not have a fuse in the neutral or grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type

of electrical connection you will be using and follow the

instructions provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor

is permanently connected to the neutral conductor (white

wire) within the dryer. If the dryer is installed with a 4-wire

electrical supply connection, the neutral ground conductor

must be removed from the external ground connector (green

screw), and secured under the neutral terminal (center or

white wire) of the terminal block. When the neutral ground

conductor is secured under the neutral terminal (center or

white wire) of the terminal block, the dryer cabinet is isolated

from the neutral conductor.

■ If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-wire

connection” section.

■ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

and (2) areas where local codes prohibit grounding through

the neutral conductor.

ELECTRIC DRYER ELECTRICAL REQUIREMENTS

(U.S.A. ONLY) (ÉTATS-UNIS SEULEMENT)

11

Electric Dryer Power Supply Cord

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■ A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or “U” shaped spade terminals

with upturned ends.

■ A UL listed strain relief.

If your outlet looks like this:

4-Wire

Receptacle

(14-30R)

3-Wire

Receptacle

(10-30R)

Then choose a 4-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

4-wire power supply cord, at least 4 ft. (1.22 m)

long, must have four 10-gauge copper wires and

match a 4-wire receptacle of NEMA Type 14-30R.

The ground wire (ground conductor) may be either

green or bare. The neutral conductor must be

identied by a white cover.

Then choose a 3-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

3-wire power supply cord, at least 4 ft. (1.22 m)

long, must have three 10-gauge copper wires and

match a 3-wire receptacle of NEMA Type 10-30R.

If your outlet looks like this:

ELECTRIC DRYER ELECTRICAL REQUIREMENTS

(U.S.A. ONLY) (ÉTATS-UNIS SEULEMENT)

Direct Wire

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper

cable (with ground wire), covered with exible metallic

conduit. All current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

12

DRYER VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible metal vent shall be used for

exhausting.

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may result

in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 7

3

⁄

4

ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or exible metal vents. Review “Vent System Chart” and

if necessary, modify existing vent system to achieve best drying

performance.

4"

(102 mm)

4" (102 mm) Heavy, Metal Exhaust Vent

Elbows:

■ 45° elbows provide better airow than 90° elbows.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Better

Good

13

4" (102 mm) Diameter Exhaust Hoods

Vent Hoods

DRYER VENTING REQUIREMENTS

Exhaust hood must be at least 12" (305 mm) from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of 90˚ Turns

Box and

Louvered Hood

Angled Hood

0 64 ft. (19.5 m) 58 ft. (17.7 m)

1 54 ft. (16.5 m) 48 ft. (14.6 m)

2 44 ft. (13.4 m) 38 ft. (11.6 m)

3 35 ft. (10.7 m) 29 ft. (8.8 m)

4 27 ft. (8.2 m) 21 ft. (6.4 m)

For vent systems not covered by the vent specication chart,

see your parts distributor.

Provision must be made for enough air for combustion

and ventilation. (Check governing codes and ordinances.)

See “Recessed Area Installation Instructions” in the “Location

Requirements” sections.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄

2

"

(64 mm) outlet exhaust hood may be used. A 2

1

⁄

2

" (64 mm)

outlet creates greater back pressure than other hood types.

For permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 4" (102 mm) clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

12" min.

(305 mm)

Vent collar

Box Hood Louvered Hood Angled Hood

14

The outside end of main vent should have a sweep elbow

directed downward.

If main vent travels vertically through the roof, rather than

through wall, install a 180° sweep elbow on end of vent at least

2 ft. (610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1⁄2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

12" min.

(305 mm)*

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 5663 l/min. (200 CFM)

of air per dryer. Large-capacity lint screens of proper design

may be used in main vent if checked and cleaned frequently.

The room where the dryers are located should have make-up

air equal to or greater than CFM of all the dryers in the room.

Back-draft Damper Kit, Part No. 3391910, is available from

your distributor and should be installed in the vent of each

dryer to keep exhausted air from returning into dryers and to

keep exhaust in balance within main vent. Unobstructed return

air openings are required.

Each vent should enter the main vent at an angle pointing in

the direction of the airow. Vents entering from the opposite

side should be staggered to reduce the exhausted air from

interfering with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

Keep air openings free of dry cleaning uid fumes. Fumes

create acids which, when drawn through the dryer heating

units, can damage dryers and items being dried.

A clean-out cover should be located on the main vent for

periodic cleaning of the vent system.

If an Exhaust Hood Cannot be Used Multiple Dryer Venting

DRYER VENTING REQUIREMENTS

24" min.

(610 mm)

* Minimum clearance above

any accumulation of snow,

ice, or debris such as leaves

1. Remove red cap from gas pipe on back of dryer.

2. Connect gas supply to dryer. Use a pipe thread compound

approved for the type of gas supplied. If exible metal

tubing is used, be certain there are no kinks.

If necessary for service, open the toe panel. Use a putty

knife to press on the toe panel locks located at the upper

corners of the toe panel. Pull downward on the toe panel

to open. Toe panel is hinged at the bottom.

3. Open the shut-off valve in the gas supply line and make sure

the dryer has its own gas supply opened.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show

a leak. Correct any leaks found.

Make Gas Connection

GAS SUPPLY CONNECTION

30˚ max.

air ow

Air Flow

15

This dryer is equipped for use with natural gas. It is design-

certied by CSA International for LP (propane and butane)

gases with appropriate conversion. No attempt shall be made

to convert dryer from gas specied on serial/rating plate for use

with a different gas without consulting the serving gas supplier.

Conversion must be done by a qualied service technician.

Gas conversion kit part numbers are listed on gas valve

burner base.

Type of Gas

GAS SUPPLY CONNECTION

Recommended Method

Provide a gas supply line of 1⁄2" (13 mm) rigid (IPS) pipe to

dryer location. Pipe joint compounds that resist action of LP

gas must be used. Do not use TEFLON

®†

tape. With LP gas,

piping or tubing size can be 1⁄2" (13 mm) minimum. Usually, LP

gas suppliers determine size and materials used in the system.

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping, accessible for

gauge testing, must be installed immediately downstream of

the installed shut-off valve to the dryer (as shown above). The

dryer must be disconnected from the gas supply piping system

during any pressure testing of the system at test pressures in

excess of 1/2" psig (352 kg/m

2

).

Alternate Method

The gas supply may also be connected using 3⁄8" (10 mm)

approved copper or aluminum tubing. If the total length of

the supply line is more than 20 ft. (6.1 m), larger tubing will

be required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off

valve installed within 6 ft. (1.8 m) of dryer in accordance

with National Fuel Gas Code, ANSI Z223.1. This valve should

be located in same room as dryer. It should be in a location

that allows ease of opening and closing. Do not block access

to shut-off valve. In Canada, an individual manual shut-off

valve must be installed in accordance with the B149 installation

codes CAN/CGA B149.1 and CAN/CGA B149.2.

Gas Supply Line

Flexible Metal Appliance Connector

It is recommended that a new exible stainless steel gas line,

design-certied by CSA International, be used for connecting

the dryer to the gas supply line. (The gas pipe which extends

through the lower rear of the dryer is provided with 3⁄8"

[10 mm] male pipe thread.)

NOTE: Do not kink or damage the exible stainless steel gas

line when moving the dryer.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe ttings

to obtain an in-line connection to the dryer.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

16

INSTALLING COIN SLIDE AND COIN BOX

The console houses the factory-installed accumulator timer

with actuating arm and button.

The factory-installed timer is set to provide 45 minutes (4 pins)

of drying time when activated by the coin slide. Timer cams

for 30-minute (6 pins) and 60-minute (3 pins) drying times are

included in the parts bag.

The coin slide mechanism, control panel lock and key, and coin

box lock and key are not included and are available from the

usual industry sources.

1. Move dryer to desired location

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging oor covering.

Using two or more people, move dryer to desired installation

location.

Check that each leg is approximately 1" (25 mm) from base.

Open dryer and remove the literature and parts packages.

Wipe drum interior with a damp cloth to remove any dust.

2. Install coin slide and coin box

a. Install coin vaults and locks (not supplied) into meter case

openings.

b. Install control panel lock and key (not supplied).

c. If you wish to change the 45-minute dryer timing cams

to either 30- or 60-minute timing cams, see “Changing

to a 30- or 60-Minute Timing Cam” section. Complete all

of the steps given in that section before going to Step d.

d. Open control panel and rest it on the bottom edge of

the opening. Attach slide extension (with ange pointing

down) to one of the coin-slide mechanisms.

e. Insert the coin-slide mechanism through the opening

to the left of the control panel.

f. Secure the coin slide mechanism from inside the control

panel using the 3⁄16" bolt and washer included with the

slide mechanism.

g. Install the coin box.

h. Repeat Steps d, e, f, and g for the other coin-slide

mechanism.

i. For added security between the upper dryer

and the collar, insert the cotter hair pin through

the connecting bolt.

j. Close the control panel.

17

Power Supply Cord Strain Relief

1. Insert strain relief.

2. Insert power cord into strain relief.

Remove Terminal Block Cover

Strain Relief

ELECTRIC DRYER ELECTRICAL CONNECTIONS

(U.S.A. ONLY) (ÉTATS-UNIS SEULEMENT)

Direct Wire Strain Relief

1. Insert strain relief.

2. Insert conduit into strain relief and tighten clamp.

18

ELECTRIC DRYER ELECTRICAL CONNECTIONS

Power Cord

4-wire receptacle (NEMA Type 14-30R)

3-wire receptacle (NEMA Type 10-30R)

Standard Power Supply Cord Connectors

Flanged Spade Connector Ring Connector

Connecting Ground and Neutral Wires

1. Remove center terminal block screw and the ground wire

by removing the external ground connector screw.

2. Connect ground and neutral wire to center terminal block.

Connection Options

Connecting 4-Wire Connection: Power Supply Cord

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire

connections.

Direct Wire

4-wire direct

3-wire direct

1"

(25 mm)

5"

(127 mm)

Connecting Direct Wire Ground

3. Connect ground wire (green or bare) with external ground

connector screw.

Connecting Remaining Wires

4. Connect remaining wires with outer terminal block screws.

19

2. Connect neutral wire to center terminal block.

3. Connect remaining wires with outer terminal block screws.

Standard Power Cord Connectors

Flanged Spade Connector Ring Connector

Connecting Neutral Wire

1. Loosen or remove center terminal block screw.

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire

connections.

Direct wire cable must have 5 ft. (1.52 m) of extra length so

dryer can be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable,

leaving bare ground wire at 5" (127 mm). Cut 1

1

⁄

2

" (38 mm)

from 3 remaining wires. Strip insulation back 1" (25 mm).

Shape ends of wires into a hook shape.

Connecting 3-Wire Connection: Power Supply Cord

Connecting 4-Wire Connection: Direct Wire

ELECTRIC DRYER ELECTRICAL CONNECTIONS

Connecting Ground and Neutral Wires

1. Remove center terminal block screw and the ground wire

by removing the external ground connector screw.

20

2. Connect neutral wire to center terminal block.

3. Connect remaining wires to outer terminal block.

Connecting Ground and Neutral Wires (cont.)

2. Connect ground and neutral wire to center terminal block.

Connecting Direct Wire Ground

3. Connect ground wire (green or bare) with external ground

connector screw.

Use where local codes permit connecting

cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft. (1.52 m) of extra length so

dryer can be moved if needed.

Strip 3

1

⁄

2

" (89 mm) of outer covering from end of cable. Strip

insulation back 1" (25 mm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape ends of

wires into a hook shape.

Connecting Neutral Wire

1. Loosen or remove center terminal block screw.

Connecting Remaining Wires

4. Connect remaining wires to outer terminal block.

Connecting 3-Wire Connection: Direct Wire

Connecting 4-Wire Connection: Direct Wire

ELECTRIC DRYER ELECTRICAL CONNECTIONS

La page charge ...

Whirlpool CSP2860TQ Guide d'installation

Whirlpool CSP2860TQ Guide d'installation

dans d''autres langues

Documents connexes