Faber Inca In-Light 35 SSV with VAM Guide d'installation

INLT21SSV

INLT28SSV

INLT35SSV

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

INCA IN-LIGHT

2

CONTENTS

Section Page

Important safety instructions

3

Range hood dimensions

6

Installation height requirements

7

Parts

8

Tools needed

10

Venting method

11

Preparing the cabinet

12

Preparing to mount the range hood

13

Choosing venting method

16

Attach venting: option 1 - rear or top vented

17

Attach venting: option 2 - non ducted recirculating

18

Connecting house power

19

Operating the controls

22

Remote control

23

Cleaning stainless steel

24

Cleaning the lter cover panel

24

Caring for lters

25

Replacing the activated charcoal lter

26

Changing and Inserting the charcoal lter

27

Replacing bulbs

27

Wiring diagram

28

Warranty

29

3

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS Range Hood

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b) Always turn hood ON when cooking at high heat or when ambeing food (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or

lter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a) SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then turn off the

burner. BE CAREFUL TO PREVENT BURNS. If the ames do not go out immediately

EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate

it.

2. The re is small and contained in the area where it started.

3. The re department is being called.

4. You can ght the re with your back to an exit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with

any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explo-

sive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Installation Work And Electrical Wiring Must Be Done By Qualied Person(s) In Accor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcient air is needed for proper combustion and exhausting of gases through the

ue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating

equipment manufacturer's guideline and safety standards such as those published by

the National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

4

ALL WALL AND FLOOR OPENINGS WHERE THE Range Hood IS INSTALLED

MUST BE SEALED.

This Range Hood requires at least 24" of clearance between the bottom of the Range

Hood and the cooking surface or countertop. This hood has been approved by UL at this

distance from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking

surface or countertop. Consult the cooktop or range installation instructions given by the

manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements"

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either

through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to

provide efcient performance. The size of the ductwork should be uniform. Do not install

two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking

to seal exterior wall or oor opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air

turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making

cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut,

then a supporting frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION - To reduce risk of re and to properly exhaust air, be sure to duct air outside

– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces,

or garages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a nonme-

tallic thermal break should be installed to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the thermal break. The break should be as

close as possible to where the vent system enters the heated portion of the house.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

4. Ducted fans must always be vented to the outdoors.

5

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit.

A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local

codes in accordance with the electrical rating of this unit as specied on the serial/rating

plate located inside the unit near the eld wiring compartment.

ELECTRICAL INSTALLATION WITH WIRING BOX

THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform

to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all

local codes and ordinances. Wire size and connections must conform with the rating of

the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker)

through exible, armored or nonmetallic sheathed copper cable. Allow some slack in

the cable so the appliance can be moved if servicing is ever necessary. A UL Listed,

1/2" conduit connector must be provided at each end of the power supply cable (at

the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through

wood must be sanded until smooth. A hole through metal must have a grommet.

• Electrical ground is required on this Range Hood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other

materials, DO NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral

or grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the Range

Hood is properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

6

RANGE HOOD DIMENSIONS

DRAFT 19-JUN-2020 14:46

21"

28"

35"

21"

28"

35"

DRAFT 19-JUN-2020 14:46

7

INSTALLATION HEIGHT REQUIREMENTS

MIN. 24" OVER ELECTRIC / MIN. 30" OVER GAS

Min. 24" Min. 30"

8

PARTS

REF. PART

QTY

A

Hood body 1

B

Bracket 2

D

Recirculation vent grill 2

E

Damper flaps 2

F

Metallic damper ring 1

Z

Remote Control 1

REF

PART

G

Pozi Screws (1/8" x 3/8")

2

I

Pozi Screws (1/8" x 5/8")

4

L

Screws plug

2

PARTS INCLUDED

9

A

D

E

F

Z

B

10

PARTS NEEDED

PARTS (cont.)

PART

6" Round Metal Ductwork

Foil tape

TOOLS NEEDED

TOOL

Tape Measure

Pencil

Electric Drill with 5/16" Drill Bit

Phillips Screwdriver

Metal sheers

Work gloves

ACCESSORIES AVAILABLE

ACCESSORY SKU#

Activated Charcoal Filter Kit #FILTER1

Activated Charcoal Filter Kit Washable Long Lasting #FILTER1LL

Direct Connect Wiring Box #WIREBOX

Standard Liner 24 (Use only with INLT21SSV) #LINE24ST

Standard Liner 30 (Use only with INLT28SSV) #LINE30ST

Standard Liner 36 (Use only with INLT28SSV) #LINE36ST

Pro Liner 36 (Use only with INLT35SSV) #LINE36PT

Self supporting liner (Use only with INLT28SSV) #LINSPT301228

Self supporting liner (Use only with INLT28SSV) #LINSPT361228

11

VENTING METHOD

Option 1: REAR OR TOP VENTED

Option 2: RECIRCULATING

Rear

6"

1

Requires purchase of

Activated Charcoal

Accessory kit.

6"

Top

12

1

2

















The Hood can be installed directly on the underside of the cabinet.

If you use the Self supporting liner #LINSPT301228 or

#LINSPT361228, please follow the instructions included in the

corresponding self supporting liner manual.

If you do not use the Self supporting liner, create a cut out in the

bottom of the cabinet as shown in the illustration.

PREPARING THE CABINET

21"

28"

35"

13

PREPARING TO MOUNT THE RANGE HOOD

Attach the brackets

B

with two screws

I

as shown in the

center of the cut out on each side. The edge of the bracket

should align with the cut out edge.

If you are installing a Self supporting liner (#LINSPT301228 or

#LINSPT361228), brackets need to be attached directly to the

bottom lip of the metal liner.

3

B

=

4x

2x













I

14

Open the filter panel cover away from you by pulling down from the magnetic catch.

Remove the grease filters by pushing the release tab towards the back of the hood.

4

5

Ø 120

F

MIN.

200mm

6

7

F

Ø 125

Ø 150

5

ZZ

15

6

Insert the hood in the cut out until the side installation clips snap into place

above the previously installed side wall brackets. Lock the hood into position

by tightening the 2 screws Vf from underneath.

Insert the 2 plastic hole covers

L

one on each side into the screw holes.

[

(3)

2x

Vf

L

2x

16

CHOOSING VENTING METHOD

Option 1: REAR OR TOP VENTED

Option 2: RECIRCULATING

7

Requires purchase of

Activated Charcoal

Accessory kit.

Rear

6"

Top

Go to Pg.17

Go to Pg.18

17

Install the Damper flaps

E

that are

included with hood by snapping the

tabs into place inside the top of the

hood before connecting ductwork.

Install Roof or Wall Cap purchased

separately. Connect the 6" metal

ductwork to the Roof or Wall Cap

and then attach ductwork. Seal with

foil tape.

D



D



Install Metal damper ring

F

included with

the Hood.

1

2

3

ATTACH VENTING: OPTION 1 - REAR OR TOP

VENTED

F

E

18

1

ATTACH VENTING: OPTION 2 - NON DUCTED

RECIRCULATING

Required Activated Charcoal Filter

Accessory - sku # - FILTER1

Long Lasting Activated Charcoal Filter

Accessory - sku # FILTER1LL

(purchased separately)

For Non-Ducted Recirculation venting

route the ductwork to a location above

the hood where the discharge is vented

back into the room.

Use the included Recirculation Vent Grill

D

to cover the opening. Secure the grill

with the 2 screws

G

provided in the

Install Kit.

A straight 6" round duct that is at least

15" in length should be used to lead air

from the top of the hood exhaust outlet

to the exit of the cabinet above.





´

D

G

19

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

The power cord shall be accessible for inspection after installation.

ELECTRICAL INSTALLATION WITH OPTIONAL WIRING BOX

For permanent wiring, use only the Direct Connect Wiring Box accessory sku

WIREBOX, manufactured by Faber.

Max. 33 7/16”

ELECTRICAL INSTALLATION WITH CONNECTION CABLE

GROUNDING INSTRUCTIONS This appliance must be grounded. In the event

of an electrical short circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electric current. This appliance is equipped

with a cord having a grounding wire with a grounding plug. The plug must be

plugged into an outlet that is properly installed and grounded.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are not completely

understood, or if doubt exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a

qualified electrician install an outlet near the appliance.

CONNECTING HOUSE POWER

8

20

FOR NON-DUCTED RECIRCULATION OPTION

Attach each charcoal filter to the black grid on each side of the blower.

Press the charcoal filter tightly to the black grid on the blower side and

rotate the filter clockwise (towards the front of the insert hood) until it locks

into place. Turn counterclockwise (towards the back of the insert hood)

to remove (for more details see paragraph Changing and Inserting the

Charcoal Filter)

.

1

2

Required Activated Charcoal Filter

Accessory - sku # - FILTER1

Long Lasting Activated Charcoal

Filter Accessory - sku # FILTER1LL

(purchased separately)

9

La page charge ...

Faber Inca In-Light 35 SSV with VAM Guide d'installation

Faber Inca In-Light 35 SSV with VAM Guide d'installation

dans d''autres langues

Documents connexes

Autres documents