Maytag GGG388LXB03 Installation Instructions Manual

Maytag
Marque
Maytag
Modèle
GGG388LXB03
Catégorie
Cuisinières
Taper
Installation Instructions Manual

Ce manuel convient également à

INSTALLATIONINSTRUCTIONS
30" (76.2 CM) DOUBLEOVEN GAS RANGES
INSTRUCTIONSPOURL'INSTALLATIONDESCUISINIERES
A GAZ A DOUBLEFOURDE30" (76,2 CM)
TableofContents
RANGE SAFETY ............................................................................. 2
INSTALLATION REQUIREMENTS ................................................ 3
Tools and Parts............................................................................ 3
Location Requirements ............................................................... 3
Electrical Requirements ............................................................... 5
Gas Supply Requirements ........................................................... 5
INSTALLATION INSTRUCTIONS .................................................. 7
Unpack Range ............................................................................. 7
Adjust Leveling Legs ................................................................... 7
Install Anti-Tip Bracket ................................................................ 7
Make Gas Connection ................................................................. 8
Verify Anti-Tip Bracket Is Installed and Engaged ........................ 9
Level Range ................................................................................. 9
Electronic Ignition System ......................................................... 10
Complete Installation ................................................................. 11
GAS CONVERSIONS ................................................................... 11
LP Gas Conversion .................................................................... 11
Natural Gas Conversion ............................................................ 15
Tabledes mah_res
SleCURITle DE LA CUISINIERE ................................................... 19
EXIGENCES D'INSTALLATION ................................................... 20
Outils et pieces ........................................................................... 20
Exigences d'emplacement ......................................................... 21
Specifications electriques .......................................................... 22
Specifications de I'alimentation en gaz ..................................... 23
INSTRUCTIONS D'INSTALLATION ............................................. 24
Deballage de la cuisiniere .......................................................... 24
Reglage des pieds de nivellement ............................................. 24
Installation de la bride antibasculement .................................... 25
Raccordement au gaz ................................................................ 25
Verifier que la bride antibasculement est bien
installee et engagee .................................................................... 26
Reglage de I'aplomb de la cuisiniere ......................................... 27
Systeme d'allumage electronique .............................................. 27
Achever I'installation .................................................................. 28
CONVERSIONS POUR CHANGEMENT DE GAZ....................... 29
Conversion pour I'alimentation au propane ............................... 29
Conversion pour I'alimentation au gaz naturel .......................... 33
iMPORTANT:
Save for local electrical inspector's use.
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
iMPORTANT :
_, conserver pour consultation par I'inspecteur local des installations 61ectriques.
Installateur : Remettre les instructions d'installation au propri6taire.
Propri6taire : Conserver les instructions d'installation pour r6f6rence ult_rieure.
W10430959A
RANGESAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death,
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance,
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or
the gas supplier,
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.
In the State of Massachusetts, the following installation instructions apply:
m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
m If using a ball valve, it shall be a T-handle type.
m A flexible gas connector, when used, must not exceed 3 feet.
2
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
Iq Anti-Tip
Ra_ '''Bracket
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
Tools needed
• Tape measure • 1/8"(3.2 mm) drill bit
• Phillips screwdriver • Marker or pencil
• Torx®tT-20®screwdriver • Pipe-joint compound
resistant to LP gas
• Flat-blade screwdriver
• 1/8"flat-blade screwdriver • Noncorrosive leak-detection
solution
• Level
For LP/Natural Gas
• Hand or electric drill Conversions
• Wrench or pliers • 1/2"combination wrench
• Pipe wrench • 9/32"(7.0 mm) nut driver
• Wle" combination wrench • Masking tape
Parts supplied
Check that all parts are included.
• LP/Natural Gas Conversion Kit (located on back of range near
lower side)
• Burner grates
• Burner caps
• Oven racks
• 2 - #12 x 1%" screws (for mounting anti-tip bracket)
• Anti-tip bracket (taped inside upper oven with literature
package)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
Parts needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See "Electrical Requirements" and
"Gas Supply Requirements" sections.
I"®TORX and T-20 are registered trademarks of Saturn Fasteners, Inc.
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
• It is the installer's responsibility to comply with installation
clearances specified on the rating number plate. The rating
number plate is located behind the control panel.
• The range should be located for convenient use in the
kitchen.
• Recessed installations must provide complete enclosure of
the sides and rear of the range.
• To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
or microwave hood combination that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
• All openings in the wall or floor where range is to be installed
must be sealed.
• Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
• The floor anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see "Install Anti-Tip
Bracket" section.
• Grounded electrical supply is required. See "Electrical
Requirements" section.
• Proper gas supply connection must be available. See "Gas
Supply Requirements" section.
• Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
• Use an insulated pad or _¼"(0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest edition, or with local
codes.
Mobile home installations require:
• When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
Product Dimensions
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
A
\
A
F
A. 353/4"_+%" (90.8 _+0.3 cm)
cooktop height (minimum)
with levering legs screwed
aft the way in
B. Model/serial/rating plates
(located behind the
control panel)*
C. 47%" _+%" (119. 7 _+0.3 cm) overall
height (minimum) with leveling
legs screwed all the way in**
D. 281/2'' _+1/4"(72.4 _+0.6 cm) depth
with handle
E. 26%" to 27¼" _+%" (66.4 to
69.2 cm _+0.3 cm)***
F. 2915/16'' _+1A6"(76.0 _+0.2 cm) width
*Model/serial/rating plates may be rotated up from behind the
control panel for viewing from the front of the range.
**Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
***Excludes handle. Dimension given is from wall to front of oven
door and will vary based on electrical outlet receptacle
installation.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
A. 18" (45. 7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to the top of the cooktop, see NOTE.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of the range to the side
waft or other combustible material.
G. Cabinet door or hinges should not extend into the cutout.
H. 3" (7.6 cm) distance from wall
I. 11/2'' (3.8 cm) min. from right side cabinet
J. 8" (20.3 cm) width
K. 7" (17.8 cm) min. from floor
L. 2" (5.1 cm) min. from floor
*Drill on centerline 11¼'' (3.1 cm) from rear wall for gas supply
line.
**Gas lines must be installed within the shaded area to ensure
proper alignment of this oven with cabinets.
***Electrical plugs must be installed within the shaded area to
ensure proper alignment of this oven with cabinets.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is covered by not less than 1/4"(0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT: The range must be electrically grounded in
accordance with local codes and ordinances, or in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70
or Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is
required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this range be provided.
• Electronic ignition systems operate within wide voltage limits,
but proper grounding and polarity are necessary. Check that
the outlet provides 120-volt power and is correctly grounded.
• The wiring diagram is located on the back of the range in a
clear plastic bag.
Explosion Hazard
Use a new CSA international approved gas supply line.
install a shut=off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Fai(ure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest
edition.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturers instructions.
Type of Gas
Natural gas:
This range is design-certified by CSA International for use with
Natural gas or, after proper conversion, for use with LP gas.
• This range is factory set for use with Natural gas. See "Gas
Conversions" section. The model/serial rating plate located
behind the control panel has information on the types of gas
that can be used. If the types of gas listed do not include the
type of gas available, check with the local gas supplier.
LP gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier. See "Gas
Conversions" section.
Gas Supply Line
• Provide a gas supply line of 3_,,(1.9 cm) rigid pipe to the
range location. A smaller size pipe on longer runs may result
in insufficient gas supply. With LP gas, piping or tubing size
can be 1/2"(1.3 cm) minimum. Usually, LP gas suppliers
determine the size and materials used in the system.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON ®ttape.
Flexible metal appliance connector:
• If local codes permit, a new CSA design-certified,
4 to 5 ft (122 to 152.4 cm) long, 1/2"(1.3 cm) or
3_,,(1.9 cm) I.D., flexible metal appliance connector may
be used for connecting range to the gas supply line.
• A 1/2"(1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the appliance
pressure regulator.
• Do not kink or damage the flexible metal tubing when
moving the range.
Must include a shutoff valve:
The supply line must be equipped with a manual shutoff
valve. This valve should be located in the same room but
external to the range opening, such as an adjacent cabinet. It
should be in a location that allows ease of opening and
closing. Do not block access to shutoff valve. The valve is for
turning on or shutting off gas to the range.
B
A _N
A. Gas supply line
B. Shutoff valve "opon" position
C. To range
Gas Pressure Regulator
The gas pressure regulator supplied with this range must be
used. The inlet pressure to the regulator should be as follows for
proper operation:
Natural gas:
Minimum pressure: 5" WCP
Maximum pressure: 14" WCP
LP gas:
Minimum pressure: 11" WCP
Maximum pressure: 14" WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at a
rate of 4% for each 1,000 ft (304.8 m) above sea level (not
applicable for Canada).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least
1" water column pressure above the manifold pressure shown
on the model/serial rating plate.
Line pressure testing above 1/2psi gauge (14" WCP)
The range and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2psi (3.5 kPa).
Line pressure testing at 1/2psi gauge (14" WCP) or lower
The range must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than 1/2psi (3.5 kPa).
t®TEFLON isa registered trademark of E.I. Du Pont De Nemours and Company.
6
INSTALLATIONINSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
1. Remove shipping materials, tape and film from the range.
Keep cardboard bottom under range.
2. Remove oven racks and parts package from inside oven.
3. To place range on its back, take 4 cardboard corners from the
carton. Stack one cardboard corner on top of another.
Repeat with the other 2 corners. Place them lengthwise on
the floor behind the range to support the range when it is laid
on its back.
4. Using 2 or more people, firmly grasp the range and gently lay
it on its back on the cardboard corners.
5. Pull cardboard bottom firmly to remove.
6. Use an adjustable wrench to loosen the leveling legs.
7. Place cardboard or hardboard in front of range. Using 2 or more
people, stand range back up onto cardboard or hardboard.
1.
2.
3.
1_ ¸, _ _ , _% ,#_ _,_
I,,,._IJ]iI_,,,,i4_>I
If range height adjustment is necessary, use a wrench or
pliers to loosen the 4 leveling legs.
This may be done with the range on its back or with the range
supported on 2 legs after the range has been placed back to
a standing position.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto the cardboard or
hardboard.
Adjust the leveling legs to the correct height. Leveling legs
can be loosened to add up to a maximum of 1" (2.5 cm). A
minimum of 3Ad'(5.0 mm) is needed to engage the anti-tip
bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, then tilt forward to
adjust the rear legs.
When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its final location, check that the anti-
tip bracket will slide under the range and onto the rear
leveling leg prior to anti-tip bracket installation.
.,.,.ullPlI-,p
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Remove the anti-tip bracket that is taped inside the upper
oven with the package containing literature.
2. Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor, you can use the wall
mounting method.
3.
Determine and mark edge of range in the cutout space. The
mounting bracket can be installed on either the left side or
right side of the cutout. Position mounting bracket in cutout
so that right (or left) edge of the bracket is 15/le"(2.4 cm) from
the marked edge of the range, as shown.
: A
t %
I
I
1
B............ii
I i
i
I
x_ x _
,J
A. Anti-tip bracket
B. Mark edge of range.
C. 1%d' (2.4 cm)
4.
5.
Drill two %" (3.0 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following
illustrations.
Floor Mounting Wall Mounting
A. #12 x 1%" screws
B.Anti-tip bracket
A. #12 x 1%" screws
B. Anti-tip bracket
Using a Phillips screwdriver, mount anti-tip bracket to the wall
or floor with the two #12 x 1s/8'' screws provided.
Explosion Hazard
Use a new CSA International approved gas supply line.
instal a shut=off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
3=
Use a 15Ae"combination wrench and an adjustable wrench to
attach the flexible connector to the adapters. Check that
connector is not kinked.
..............A
r
i
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have Y2"male
pipe thread)
D. Flexible connector
E.Manual gas shutoff valve
F Y2"or 3/4"gas pipe
G. Use pipe-joint compound.
H. Adapter
4. Gas supply pipe must be located within the shaded area as
shown in the "Cabinet Dimensions" illustration in "Location
Requirements" section.
A
A. Gas pressure regulator
B.Adapter
C. Flexible connector
D. Manual shutoff valve
Complete connection
1. Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
Typical flexible connection
1. Apply pipe-joint compound made for use with LP gas to the
smaller thread ends of the flexible connector adapters (see B
and G in the following illustration).
2. Attach one adapter to the gas pressure regulator and the
other adapter to the gas shutoff valve. Tighten both adapters.
2=
A. Closed valve
B. Open valve
Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear, a
leak is indicated. Correct any leak found.
8
3=
4=
1=
Remove cooktop burner caps and grates from parts
package. Align recess in burner caps with pins in burner
base. Burner caps should be level when properly positioned.
If burner caps are not properly positioned, surface burners
will not light. Place burner grates over burners and caps.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Plug into a grounded 3 prong outlet.
Place the outside of your foot against the bottom front of the
oven door to keep the unit from moving, and grasp the lower
right or left side of the control panel as shown.
NOTE: If your countertop is mounted with a backsplash, it
may be necessary to grasp the range higher than is shown in
the illustration.
3. If the rear of the range lifts more than 1/2"(1.3 cm) off the floor
without resistance, stop tilting the range and lower it gently
back to the floor. The range foot is not engaged in the anti-tip
bracket.
IMPORTANT: If there is a snapping or popping sound when lifting
the range, the range may not be fully engaged in the bracket.
Check to see if there are obstructions keeping the range from
sliding to the wall or keeping the range foot from sliding into the
bracket. Verify that the bracket is held securely in place by the
mounting screws.
4. Slide the range forward, and verify that the anti-tip bracket is
securely attached to the floor or wall.
5. Slide range back so the rear range foot is inserted into the
slot of the anti-tip bracket.
IMPORTANT: If the back of the range is more than 2" (5.1 cm)
from the mounting wall, the rear range foot may not engage the
bracket. Slide the range forward and determine if there is an
obstruction between the range and the mounting wall. Changes
to the gas supply must be performed by a qualified service
technician. If you need assistance or service, refer to the
"Assistance or Service" section of the Use and Care Guide, or the
cover or "Warranty" section of the User Instructions, for contact
information.
6. Repeat steps 1 and 2 to ensure that the range foot is
engaged in the anti-tip bracket.
If the rear of the range lifts more than 1/2"(1.3 cm) off the floor
without resistance, the anti-tip bracket may not be installed
correctly. Do not operate the range without anti-tip bracket
installed and engaged. Please reference the "Assistance or
Service" section of the Use and Care Guide, or the cover or
"Warranty" section of the User Instructions, to contact
service.
1=
2.
Place rack in oven.
Place level on rack and check levelness of range, first side to
side; then front to back.
3. If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.
4. Use wrench to adjust leveling legs up or down until range is
level. Push range back into position.
5. Check that rear leveling leg is engaged in anti-tip bracket.
NOTE: Range must be level for satisfactory baking performance.
2. Slowly attempt to tilt the range forward.
If you encounter immediate resistance, the range foot is
engaged in the anti-tip bracket.
Initial lighting and gas flame adjustments
Cooktop and oven burners use pilotless igniters in place of
standing pilots. When the cooktop control knob is turned to the
"LITE" position, the system creates a spark to light the burner.
This sparking continues, as long as the control knob is turned to
"LITE."
When the oven control is turned to the desired setting, a glow bar
igniter heats and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the "LITE" position.
The flame should light within 4 seconds. The first time a burner is
lit it may take longer than 4 seconds to light because of air in the
gas line.
If burners do not light properly:
• Turn cooktop control knob to the "OFF" position.
• Check that the range is plugged in and the circuit breaker has
not tripped or the household fuse has not blown.
• Check that the gas shutoff valve is set to the "open" position.
• Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, turn the
control knobs to "Off" and contact your dealer or authorized
service company for assistance.
Adjust Flame Height
Adjust the height of top burner flames. The cooktop "LO" burner
flame should be a steady blue flame approximately 1¼.(0.64 cm)
high.
A
3. Replace the control knob.
4. Test the flame by turning the control from "LO" to "HI,"
checking the flame at each setting.
5. Repeat steps 1 - 4 for each burner.
Check Operation of Both Oven Bake Burners
1. Press the BAKE keypad for the desired oven.
"BAKE" scrolls down in the upper text display area or scrolls
up in the lower text display area, depending on oven
selection, and 350°F is displayed. After 3 seconds "Set temp"
scrolls in the selected oven text display area, followed by
"Push START."
2. Press START pad. "Baking" scrolls in the selected oven text
display area. Then, after 3 seconds, "Preheating" scrolls in
the display.
The igniter used to light the bake burner will glow. Once the
igniter is hot, the oven bake burner should light. Under certain
conditions, it may take up to 60 seconds for it to light.
If burners do not light properly:
• Press OFF/CANCEL to turn off the oven.
• Check that the range is plugged in and circuit breaker has not
tripped or the household fuse has not blown.
• Check that the gas shutoff valve is set to the "open" position.
Repeat start-up. If burner does not light, press OFF/CANCEL to
turn off the oven and contact your dealer or authorized service
company for assistance.
Check Operation of Oven Broil Burner
A. Low flame
B. High flame
To adjust standard burners:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
If the "low" flame needs to be adjusted:
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem in the low position using a pair of pliers.
Use a 1/8"(3.0 ram) flat-blade screwdriver to turn the screw
located in the center of the control knob stem until the flame
is the proper size.
1. Press BROIL for the upper oven. "BROIL" scrolls down in the
upper text display area, and 550°F is displayed. After
3 seconds, "Set temp" scrolls in the upper oven text display
area, followed by "Push START."
2. Press START. "Broiling" scrolls in the upper oven text display
area and remains there until the set temperature is reached.
The igniter used to light the broil burner will glow. Once the
igniter is hot, the oven burner should light. Under certain
conditions, it may take up to 60 seconds for it to light.
If burners do not light properly:
• Press OFF/CANCEL to turn off the oven.
• Check that the range is plugged in and circuit breaker has not
tripped or the household fuse has not blown.
• Check that the gas shutoff valve is set to the "open" position.
Repeat start-up. If burner does not light, press OFF/CANCEL to
turn off the oven and contact your dealer or authorized service
company for assistance.
10
C_,_,_,,,@_ t_ _,,,_tc __
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check that the range is level. See "Level Range."
5. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see
the "Range Care" section of the Use and Care Guide or User
Instructions.
6. Read the Use and Care Guide or User Instructions.
7. Turn on surface burners and oven. See the Use and Care
Guide or User Instructions for specific instruction on range
operation.
If range does not operate, check the following:
• Household fuse is intact and tight, or circuit breaker has not
tripped.
• Range is plugged into a grounded 3 prong outlet.
• Electrical supply is connected.
• See "Troubleshooting" in the Use and Care Guide or User
Instructions.
8=
When the range has been on for 5 minutes, check for heat. If
the range is cold, turn off the range and check that the gas
supply line shutoff valve is open.
• If the gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
• If the gas supply line shutoff valve is open, press the
CANCEL button on the oven control panel and contact a
qualified technician.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the Use
and Care Guide or the cover of the User Instructions, or contact
the dealer from whom you purchased your range.
GAS CONVERSIONS
Gas conversions from Natural gas to LP gas or from LP gas to
Natural gas must be done by a qualified installer.
Explosion Hazard
Use a new CSA International approved gas supply line.
instal a shut-off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
LI S
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1=
Turn manual shutoff valve to the closed position.
....................B
J ............... ......................C
A. Torange
B.Shutoff valve(closedposition)
C. Gassupply line
2. Unplug range or disconnect power.
11
To Convert Gas Pressure Regulator
1. Locate gas pressure regulator at the rear of the range.
° _ _li
rli
A.Gaspressure regulator
IMPORTANT: Do not remove the gas pressure regulator.
2. Unscrew the regulator cap and remove the plastic cover.
3. Push the bake burner cover to the right.
4=
5.
A
A. Bakeburner cover
Lift up and remove oven bake burner cover.
Unscrew wing nut and remove oven baffle.
A. Plastic cover
B. Regulator cap
3. Flip the regulator cap over and replace the plastic cover.
A
......... "C
#
A. Natural gas position
B. LP gas position
C. Plastic cover
4. Screw the regulator cap securely back into place. Do not
overtighten.
To Convert Oven Bake Burners
To Convert Lower Oven Bake Burner:
1. Remove oven racks from inside the oven cavity.
2. Remove oven door. See "Oven Door" section in the Use and
Care Guide for oven door removal instructions.
A. Oven baffle
B. Wing nut
6. Remove the oven bake burner screw and set aside.
7. Gently set the bake burner to the side.
B
A. Igniter and wires
B. Bake burner screw
12
8. Unscrew and remove the cover over the orifice. 11. Position the oven bake burner over the orifice hood and
reinstall using screw.
A
B
A
9=
A.Orifice cover
Turn the Number 0.070 Natural gas orifice hood
counterclockwise to remove.
A. Number 0.070 Natural gas orifice hood
10. Install the Number 0.044 LP gas orifice hood, turning it
clockwise 4 or 5 turns. Do not overtighten.
C
A. Bake burner orifice hood
B. Oven bake burner
C. Oven bake burner screw
To Convert Upper Oven Bake Burner
12. Repeat steps 1 through 8 above for conversion of the upper
oven bake burner.
13. Remove the Number 0.055 Natural gas orifice spud in the
upper oven and replace with a Number 0.037 LP gas orifice
spud.
14. Reverse steps to reinstall the orifice covers, oven bake
burners, oven baffles and oven bake covers in both ovens.
To Convert Oven Broil Burner
1. Remove broil burner screw and set aside.
2. Remove the broil burner from the broil burner orifice hood.
The broil burner will hang in the back of the oven while
changing the orifice hood.
A
A. Number 0.044 LP gas orifice hood
A. Broil burner screw
B. Broil burner orifice hood
13
3. Turn the Number 0.054 Natural gas broil burner orifice hood
counterclockwise to remove.
3. Using a Phillips or Torx_)screwdriver, remove the burner base.
A .........
, _F"_ ...........
B ................................._
__ :"1_- .......................................................E
4=
A
/
A.Number 0.054 Naturalgas broil burner orifice hood
Install the green Number 0.037 LP gas broil burner orifice
hood, turning it clockwise 4 or 5 turns. Do not overtighten.
...., .......
4=
A. Burner cap
B. Gas tube opening
C. Burner base screws
D. Burner base
Apply masking tape to the end of a %2"(7.0 mm) nut driver to
help hold the Natural gas orifice spud in the nut driver while
changing it. Press nut driver down onto the Natural gas orifice
spud and remove by turning it counterclockwise and lifting
out. Set the Natural gas orifice spud aside.
A
9
A. Number 0.037 LP gas broil burner orifice hood
5. Place the broil burner on the broil burner orifice hood. Insert
the broil burner Iocator pin in the hole in the oven back.
6. Position the broil burner against the roof of the oven cavity
and attach with screw.
A B
A. Broil burner orifice hood
B. Broil burner
To Convert Surface Burners
1. If the burner grates are installed, remove them.
2. Remove the burner caps.
A. Natural gas orifice spud
Use the following chart for correct LP gas orifice spud for each
burner. Refer to the model/serial rating plate behind the control
panel for proper sizing of LP gas orifice spuds for each burner
location.
LP Gas Orifice Spud Chart
Burner Rating Color Number
4,000 BTU Blue 64L
7,000 BTU Black 81L
9,100 BTU Green 97L
14,000 BTU Red 114L
5. Replace the Natural gas orifice spud with the correct LP gas
orifice spud. See the "LP Gas Orifice Spud Chart."
6. Replace burner base and hand tighten the screws.
7. Replace burner cap.
8. Repeat steps 1 through 7 for the remaining burners.
9. Place Natural gas orifice spuds in plastic parts bag for future
use and keep with literature package.
10. Replace burner grates.
11. Complete installation. See "Make Gas Connection" and
"Electronic Ignition System" sections.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
1¼.to 1/2"long. The outer cone is not as distinct as the inner
cone. LP gas flames have a slightly yellow tip.
IMPORTANT: You may have to adjust the "LO" setting for
each cooktop burner. See "Adjust Flame Height" in the
"Electronic Ignition System" section.
14
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
2. Unscrew the regulator cap and remove the plastic cover.
/
A. Plastic cover
B. Regulator cap
3. Flip the regulator cap over and replace the plastic cover.
1. Turn manual shutoff valve to the closed position.
2=
...................S
A. Torange
B.Shutoff valve(closedposition)
C. Gassupply line
Unplug range or disconnect power.
To Convert Gas Pressure Regulator
1. Locate gas pressure regulator at the rear of the range.
........................
A.Gaspressure regulator
IMPORTANT: Do not remove the gas pressure regulator.
A. LP gas position
B. Natural gas position
C. Plastic cover
4. Screw the regulator cap securely back into place. Do not
overtighten.
To Convert Oven Bake Burners
To Convert Lower Oven Bake Burner:
1. Remove oven racks from inside the oven cavity.
2. Remove oven door. See "Oven Door" section in the Use and
Care Guide for oven door removal instructions.
3. Push the bake burner cover to the right.
4,
A
A. Bakeburner cover
Lift up and remove oven bake burner cover.
15
5. Unscrew wing nut and remove oven baffle. 9. Turn the Number 0.044 LP gas orifice hood counterclockwise
to remove.
A
A. Oven baffle
B. Wing nut
6. Remove the oven bake burner screw and set aside.
7. Gently set the bake burner to the side.
B
A. Igniter and wires
B. Bake burner screw
8. Unscrew and remove the cover over the orifice.
A.Number 0.044 LP gas orifice hood
10. Install the Number 0.070 Natural gas orifice hood, turning it
clockwise 4 or 5 turns. Do not overtighten.
A
A. Number 0.070 Natural gas orifice hood
11. Position the oven bake burner over the orifice hood and
reinstall using screw.
B
A
A. Orifice cover
A
C
A. Bake burner orifice hood
B. Oven bake burner
C. Oven bake burner screw
To Convert Upper Oven Bake Burner
12. Repeat steps 1 through 8 above for conversion of the upper
oven bake burner.
13. Remove the Number 0.037 LP gas orifice spud in the upper
oven and replace with a Number 0.055 Natural gas orifice
spud.
14. Reverse steps to reinstall the orifice covers, oven bake
burners, oven baffles and oven bake covers in both ovens.
16
To Convert Oven Broil Burner
1. Remove broil burner screw and set aside.
2. Remove the broil burner from the broil burner orifice hood.
The broil burner will hang in the back of the oven while
changing the orifice hood.
B
3,
A. Broil burner screw
B. Broil burner orifice hood
Turn the green Number 0.037 LP gas broil burner orifice hood
counterclockwise to remove.
5. Place the broil burner on the broil burner orifice hood. Insert
the broil burner Iocator pin in the hole in the oven back.
6. Position the broil burner against the roof of the oven cavity
and attach with screw.
A B
J
A. Broil burner orifice hood
B. Broil burner
To Convert Surface Burners
1. If the burner grates are installed, remove them.
2. Remove the burner caps.
3. Using a Phillips or Torx®screwdriver, remove the burner base.
4,
A.Number 0.037 LPgas broil burner orifice hood
Install the Number 0.054 Natural gas broil burner orifice hood,
turning it clockwise 4 or 5 turns. Do not overtighten.
i ..................
A. Number 0.054 Natural gas broil burner orifice hood
4,
A. Burner cap C. Burner base screws
B. Gas tube opening D. Burner base
Apply masking tape to the end of a %2"(7.0 mm) nut driver to
help hold the LP gas orifice spud in the nut driver while
changing it. Press nut driver down onto the LP gas orifice
spud and remove by turning it counterclockwise and lifting
out. Set the LP gas orifice spud aside.
A
A. LP gas orifice spud
Use the following chart for correct Natural gas orifice spud for
each burner. Refer to the model/serial rating plate behind the
control panel for proper sizing of Natural orifice spuds for each
burner location.
17
Natural Gas Orifice Spud Chart
Burner Rating Color Number
5,000 BTU Green 107N
7,300 BTU Yellow 125N
9,200 BTU Orange 142N
10,000 BTU Clear 149N
15,000 BTU White 180N
16,000 BTU Black 195N
5. Replace the LP gas orifice spud with correct Natural gas
orifice spud. See the "Natural Gas Orifice Spud Chart."
6. Replace burner base and hand tighten the screws.
7=
8.
9.
10.
11.
Replace burner cap.
Repeat steps 1 through 7 for the remaining burners.
Place LP gas orifice spuds in plastic parts bag for future use
and keep with literature package.
Replace burner grates.
Complete installation. See "Make Gas Connection" and
"Electronic Ignition System" sections.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
1¼.to 1/2"long. The outer cone is not as distinct as the inner
cone. Natural gas flames do not have yellow tips.
IMPORTANT: You may have to adjust the "LO" setting for
each cooktop burner. See "Adjust Flame Height" in the
"Electronic Ignition System" section.
18
SECURITEDELACUISINIERE
Votre securite et celle des autres est tres importante.
Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de
toujours lire tousles messages de s_curit_ et de vous y conformer.
Voici le symbole d'alerte de s_curit&
Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves & vous
et & d'autres.
Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient •
Risque possible de d_cbs ou de blessure grave si vous ne
suivez pas imm_diatement les instructions.
Risque possible de d_cbs ou de blessure grave si vous
ne suivez pas les instructions.
Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
AVERTISSEMENT • Si les renseignements dans ce manuel ne sont pas exactement
observes, un incendie ou une explosion peut survenir, causant des dommages au
produit, des blessures ou un deces.
- Ne pas entreposer ni utiliser de ressence ou d'autres vapeurs ou liquides inflammables
proximite de cet appareil ou de tout autre appareil electromenager.
- QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :
• Ne pas tenter d'allumer un appareil.
• Ne pas toucher a un commutateur electrique.
• Ne pas utiliser le telephone se trouvant sur les lieux.
• Appeler immediatement le fournisseur de gaz a partir du telephone d'un voisin. Suivre
ses instructions.
• .&.defaut de joindre votre fournisseur de gaz, appeler les pompiers.
- L'installation et rentretien doivent _tre effectues par un installateur qualifie, une agence
de service ou le fournisseur de gaz,
AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.
Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).
Pour d'autre information, contacter le fournisseur de gaz local.
En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".
19
Dans 1'12tatdu Massachusetts, les instructions d'installation suivantes sont applicables :
• Les travaux d'installation et reparation doivent 6tre executes par un plombier ou tuyauteur qualifie ou licencie, ou par le
personnel qualifie d'une entreprise licenciee par 1'12tatdu Massachusetts.
• Si une vanne & boisseau spherique est utilisee, elle doit comporter une manette "T".
• Si un conduit de raccordement flexible est utilise, sa Iongueur ne doit pas depasser 3 pi.
Risque de basculement
Un enfant ou une personne adulte peut faire basculer la cuisini_re, ce qui peut causer un
d_cbs.
Fixer la bride antibasculement au plancher ou au mur, conform_ment aux instructions
d'installation.
Faire glisser de nouveau la cuisinibre de fa_on a ce que le pied arribre de la cuisinibre se
trouve dans la fente de la bride antibasculement.
R_engager la bride antibasculement si la cuisinibre a _t_ d_plac_e.
Ne pas faire fonctionner la cuisinibre si la bride antibasculement n'est pas install_e et engag_e.
Le non-respect de ces instructions peut causer un d_cbs ou des br_lures graves aux enfants et
aux adultes.
Bride
""" antibasculement
Pied de la cuisiniere
Pour v_rifier que la bride antibasculement est bien install_e et engag_e :
• Faire glisser la cuisini_re vers I'avant.
• V_rifier que la bride antibasculement est bien fix_e au plancher ou au mur.
• Faire de nouveau glisser la cuisini_re vers I'arri_re de sorte que le pied de la cuisini_re
se trouve sous la bride antibasculement.
• Voir les instructions d'installation pour plus de d_tails.
EXIGENCESD'INSTALLATION
D@C@S
Rassembler les outils et pieces necessaires avant d'entreprendre
I'installation. Lire et suivre les instructions fournies avec chacun
des outils de la liste ci-dessous.
Outils n_cessaires
• M_tre-ruban • Marqueur ou crayon
• Tournevis Phillips • Compose d'etancheite des
raccords filetes - resistant
• Tournevis Torx®tT-20®
au gaz propane
• Tournevis & lame plate • Solution non corrosive de
• Tournevis a lame plate de V8" detection des fuites
• Niveau Pour conversions pour gaz
• Perceuse manuelle ou propane/naturel
electrique • Cle mixte de Y2"
• Cle ou pince • Tourne-ecrou de %2"
(7,0 mm)
• Cle a tuyauterie
• Ruban adhesif de masquage
• Cle mixte de _5/le"
• Foret de V8"(3,2 mm)
Pi_ces fournies
Verifier que toutes les pieces sont presentes.
• Ensemble de conversion pour gaz naturel/propane (situe
I'arriere de la cuisiniere, pros de la partie inferieure)
Grilles de brQleur
Chapeaux de brQleur
Grilles du four
2 vis #12 x 1%" (pour le montage de la bride antibasculement)
Bride anti-basculement (fixee par ruban adhesif &I'interieur
du four superieur avec le sachet de documentation)
La bride antibasculement doit _tre solidement fixee & la
cloison arriere ou au plancher. La profondeur du plancher
peut necessiter des vis plus Iongues pour I'ancrage de la
bride dans lesous-plancher. Des vis plus Iongues sont
disponibles aupr_s de votre quincaillerie locale.
Pi_ces n_cessaires
Verifier les codes Iocaux et consulter le fournisseur de gaz.
Verifier I'alimentation en gaz et I'alimentation electrique
existantes. Voir les sections "Specifications electriques" et
"Specifications de I'alimentation en gaz".
I"®TORX et T-20 est un marques d6pos6e de Saturn Fasteners, Inc.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Maytag GGG388LXB03 Installation Instructions Manual

Maytag
Marque
Maytag
Modèle
GGG388LXB03
Catégorie
Cuisinières
Taper
Installation Instructions Manual
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents