LG OLED77C9PLA Manuel utilisateur

Taper
Manuel utilisateur
www.lg.com
Copyright © 2019 LG Electronics Inc. All Rights Reserved.
Please read this manual carefully before operating
your set and retain it for future reference.
OWNER’S MANUAL
Safety and Reference
*MFL71140304*
(2012-REV03)
2
ENGLISH
Warning! Safety
Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated dangerous voltage within the product’s
enclosure that may be of sucient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS
WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
Do not place the TV and/or remote control in the following
environments:
- Keep the product away from direct sunlight.
- An area with high humidity such as a bathroom
- Near any heat source such as stoves and other devices that
produce heat.
- Near kitchen counters or humidiers where they can easily be
exposed to steam or oil.
- An area exposed to rain or wind.
- Do not expose to dripping or splashing and do not place objects
lled with liquids, such as vases, cups, etc. on or over the
apparatus (e.g., on shelves above the unit).
- Near ammable objects such as gasoline or candles, or expose
the TV to direct air conditioning.
- Do not install in excessively dusty places.
Otherwise, this may result in re, electric shock, combustion/
explosion, malfunction or product deformation.
Ventilation
- Install your TV where there is proper ventilation. Do not install in
a conned space such as a bookcase.
- Do not install the product on a carpet or cushion.
- Do not block or cover the product with cloth or other materials
while unit is plugged in.
Take care not to touch the ventilation openings. When watching
the TV for a long period, the ventilation openings may become hot.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon.
Pay particular attention to plugs, wall outlets, and the point where
the cord exits the device.
Do not move the TV whilst the Power cord is plugged in.
Do not use a damaged or loosely tting power cord.
Be sure do grasp the plug when unplugging the power cord. Do
not pull on the power cord to unplug the TV.
Do not connect too many devices to the same AC power outlet as
this could result in re or electric shock.
Disconnecting the Device from the Main Power
- The power plug is the disconnecting device. In case of an
emergency, the power plug must remain readily accessible.
Do not let your children climb or cling onto the TV. Otherwise, the
TV may fall over, which may cause serious injury.
Outdoor Antenna Grounding (Can dier by country):
- If an outdoor antenna is installed, follow the precautions below.
An outdoor antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits,
or where it can come in contact with such power lines or circuits
as death or serious injury can occur.
Be sure the antenna system is grounded to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
Antenna grounding according to the National Electrical Code,
ANSI/NFPA 70
3
ENGLISH
Grounding (Except for devices which are not grounded.)
- TV with a three-prong grounded AC plug must be connected to
a three-prong grounded AC outlet. Ensure that you connect the
earth ground wire to prevent possible electric shock.
Never touch this apparatus or antenna during a lightning storm.
You may be electrocuted.
Make sure the power cord is connected securely to the TV and wall
socket if not secured damage to the Plug and socket may occur
and in extreme cases a re may break out.
Do not insert metallic or inammable objects into the product. If a
foreign object is dropped into the product, unplug the power cord
and contact the customer service.
Do not touch the end of the power cord while it is plugged in. You
may be electrocuted.
If any of the following occur, unplug the product
immediately and contact your local customer service.
- The product has been damaged.
- If water or another substance enters the product (like an AC
adapter, power cord, or TV).
- If you smell smoke or other odors coming from the TV
- When lightning storms or when unused for long periods of time.
Even the TV is turned o by remote control or button, AC power
source is connected to the unit if not unplugged in.
Do not use high voltage electrical equipment near the TV (e.g., a
bug zapper). This may result in product malfunction.
Do not attempt to modify this product in any way without written
authorization from LG Electronics. Accidental re or electric shock
can occur. Contact your local customer service for service or repair.
Unauthorized modication could void the users authority to
operate this product.
Use only an authorized attachments / accessories approved by
LG Electronics. Otherwise, this may result in re, electric shock,
malfunction, or product damage.
Never disassemble the AC adapter or power cord. This may result in
re or electric shock.
Handle the adapter carefully to avoid dropping or striking it. An
impact could damage the adapter.
To reduce the risk of re or electrical shock, do not touch the TV
with wet hands. If the power cord prongs are wet or covered with
dust, dry the power plug completely or wipe dust o.
Batteries
- Store the accessories (battery, etc.) in a safe location out of the
reach of children.
- Do not short circuit, disassemble, or allow the batteries to
overheat. Do not dispose of batteries in a re. Batteries should
not be exposed to excessive heat.
- Caution: Risk of re or explosion if the battery is replaced by an
incorrect type.
Moving
- When moving, make sure the product is turned o, unplugged,
and all cables have been removed. It may take 2 or more people
to carry larger TVs. Do not press or put stress on the front panel
of the TV. Otherwise, this may result in product damage, re
hazard or injury.
Keep the packing anti-moisture material or vinyl packing out of
the reach of children.
Do not allow an impact shock, any objects to fall into the product,
and do not drop anything onto the screen.
Do not press strongly upon the panel with a hand or a sharp
object such as a nail, pencil, or pen, or make a scratch on it. It may
causedamage to screen.
Cleaning
- When cleaning, unplug the power cord and wipe gently with a
soft/dry cloth. Do not spray water or other liquids directly on the
TV. Do not clean your TV with chemicals including glass cleaner,
any type of air freshener, insecticide, lubricants, wax (car,
industrial), abrasive, thinner, benzene, alcohol etc., which can
damage the product and/or its panel. Otherwise, this may result
in electric shock or product damage.
4
ENGLISH
Preparing
If the TV is turned on for the rst time after it was shipped from the
factory, initialization of the TV may take a few minutes.
Image shown may dier from your TV.
Your TV’s OSD (On Screen Display) may dier slightly from that
shown in this manual.
The available menus and options may dier from the input source
or product model that you are using.
New features may be added to this TV in the future.
The device must be easily accessed to a location outlet near the
access. Some devices are not made by turning on / o button,
turning o the device and unplugging the power cord.
The items supplied with your product may vary depending on the
model.
Product specications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports if the USB cable or USB
memory stick does not t into your TV’s USB port.
A
B
A
B
* A 10 mm
* B 18 mm
Use a certied cable with the HDMI logo attached.
If you do not use a certied HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI Cable Types)
- Ultra High Speed HDMI®/
TM
cable (3 m or less)
Separate Purchase
Separate purchase items can be changed or modied for quality
improvement without any notication. Contact your dealer to buy these
items. These devices only work with certain models.
The model name or design may be changed depending on the upgrade
of product functions, manufacturer’s circumstances or policies.
Magic Remote Control
AN-MR19BA
Check whether your TV model supports Bluetooth in the Wireless
Module Specication to verify whether it can be used with the Magic
Remote.
Wall Mounting Bracket
(Depending on model)
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
A
B
Model
OLED55/65B9*
OLED55/65C9*
OLED55/65E9*
OLED77B9*
OLED77C9*
VESA (A x B) (mm) 300 x 200 400 x 200
Standard screw M6 M6
Number of screws 4 4
Wall mount bracket OLW480B OLW480B
5
ENGLISH
Lifting and moving the TV
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
It is recommended to move the TV in the box or packing material
that the TV originally came in.
Before moving or lifting the TV, disconnect the power cord and all
cables.
When holding the TV, the screen should face away from you to
avoid damage.
Hold the side and bottom of the TV frame rmly. Make sure not
to hold the transparent part, speaker, or speaker grill area. (Not
applicable for OLED55/65E9*)
When transporting a large TV, there should be at least 2 people.
When transporting the TV by hand, hold the TV as shown in the
following illustration.
(Only OLED55/65E9*)
Hold the side of the TV with one hand, and hold the bottom of the
rear cover or the side of the Stand with the other. (Hold the rear
cover when placing the TV on the oor. Holding the bottom glass
may result in injury.) (Only OLED55/65E9*)
When transporting the TV, do not expose the TV to jolts or excessive
vibration.
When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
Do not apply excessive pressure to cause exing / bending of frame
chassis as it may damage screen.
When handling the TV, be careful not to damage the protruding
buttons.
•  Avoid touching the screen at all times, as this may result
in damage to the screen.
•  When attaching the stand to the TV set, place the screen
facing down on a cushioned table or at surface to
protect the screen from scratches.
•  Do not scratch or hit the glass with metal materials or
objects. It may damage the TV or lead to an accident.
(Only OLED55/65E9*)
6
ENGLISH
Mounting on the Table
1 Lift and tilt the TV into its upright position on a table.
Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
(Depending on model)
2 Connect the power cord to a wall outlet.
•  Do not apply foreign substances (oils, lubricants, etc.) to
the screw parts when assembling the product. (Doing so
may damage the product.)
•  If you install the TV on a stand, you need to take actions
to prevent the product from overturning. Otherwise, the
product may fall over, which may cause injury.
•  Do not use any unapproved items to ensure the safety
and product life span.
•  Any damage or injuries caused by using unapproved
items are not covered by the warranty.
•  Make sure that the screws are inserted correctly and
fastened securely. (If they are not fastened securely
enough, the TV may tilt forward after being installed.)
Do not use too much force and over tighten the screws;
otherwise screw may be damaged and not tighten
correctly.
Securing TV to the Wall
(Depending on model)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
If there are bolts inserted at the eye-bolts position, remove the
bolts rst.
2 Mount the wall brackets with the bolts to the wall. Match the
location of the wall bracket and the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the at surface.
Use a platform or cabinet that is strong and large enough to
support the TV securely.
Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
7
ENGLISH
Mounting to the Wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the oor. When you attach the TV to other building materials, please
contact qualied personnel. LG recommends that wall mounting be
performed by a qualied professional installer. We recommend the use
of LG’s wall mount bracket. LGs wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
10 cm
(Depending on model)
•  Remove the stand before installing the TV on a wall
mount by performing the stand attachment in reverse.
•  For more information of screws and wall mount bracket,
refer to the Separate purchase.
•  If you intend to mount the product to a wall, attach VESA
standard mounting interface (optional parts) to the back
of the product. When you install the set to use the wall
mounting bracket (optional parts), x it carefully so as
not to drop.
•  When mounting a TV on the wall, make sure not to install
the TV by hanging the power and signal cables on the
back of the TV.
•  Do not install this product on a wall if it could be exposed
to oil or oil mist. This may damage the product and cause
it to fall.
Please use the accessory cable holder when hanging on
the wall. (Only OLED55/65C9*)
Attach the three covers when installing the wall
mount. (Only when the item is provided.) (Only
OLED55/65E9*)
8
ENGLISH
Connections
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
Antenna/Cable
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
Use a signal splitter to use more than 2 TVs.
If the image quality is poor, install a signal amplier properly to
improve the image quality.
If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
An antenna cable and converter are not supplied.
For a location that is not supported with ULTRA HD broadcasting,
this TV cannot receive ULTRA HD broadcasts directly.
Satellite dish
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω). (Depending on model)
CI module
View the encrypted (pay) services in digital TV mode. (Depending on
model)
Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
HDMI
•  When connecting the HDMI cable, the product and external devices
should be turned o and unplugged.
•  Supported HDMI Audio format :
DTS (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz),
DTS HD (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz),
True HD (48 kHz),
Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)
(Depending on model)
•  ( ) [Picture] [Additional Settings] [HDMI
ULTRA HD Deep Colour]
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
- O : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case, change the TV’s
[HDMI ULTRA HD Deep Colour] setting to o.
USB
Some USB Hubs may not work. If a USB device connected using a USB
Hub is not detected, connect it to the USB port on the TV directly.
External Devices
Available external devices are: Blu-ray player, HD receivers, DVD players,
VCRs, audio systems, USB storage devices, PC, gaming devices, and
other external devices.
The external device connection may dier from the model.
Connect external devices to the TV regardless of the order of the
TV port.
If you record a TV program on a Blu-ray/DVD recorder or VCR, make
sure to connect the TV signal input cable to the TV through a DVD
recorder or VCR. For more information of recording, refer to the
manual provided with the connected device.
Refer to the external equipment’s manual for operating
instructions.
9
ENGLISH
If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the [PICTURE]
menu until the picture is clear.
In PC mode, some resolution settings may not work properly
depending on the graphics card.
If ULTRA HD content is played on your PC, video or audio may
become disrupted intermittently depending on your PC’s
performance. (Depending on model)
When connecting via a wired LAN, it is recommended to use a CAT
7 cable. (Only when port is provided.)
Using Button
You can simply operate the TV functions, using the button.
<A type>
<B type>
Basic functions
<A type>
Power On (Press)
Power O
1
(Press and Hold)
Menu Control (Press
2
)
Menu Selection (Press and Hold
3
)
1 All running apps will close, and any recording in progress will stop.
(Depending on country)
2 You can access and adjust the menu by pressing the button when
TV is on.
3 You can use the function when you access menu control.
<B type>
Power On (Press)
Power O
1
(Press and hold)
Volume Control
Programmes Control
1 All running apps will close, and any recording in progress will stop.
(Depending on country)
Adjusting the menu
When the TV is turned on, press the button one time. You can adjust
the Menu items using the button.
<A type>
Turns the power o.
Changes the input source.
Adjusts the volume level.
Scrolls through the saved programmes.
<B type>
Turns the power o.
Accesses the settings menu.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
10
ENGLISH
To use the button, press and hold for more than 1 second.
(POWER) Turns the TV on or o.
/ You can turn your set-top box on or o by adding the set-
top box to the universal remote control for your TV.
Number buttons Enters numbers.
Accesses the [QUICK HELP].
(DASH) Inserts a between numbers such as 2-1 and 2-2.
/ Accesses the saved programmes list.
(More Actions) Displays more remote control functions.
Edits QUICK ACCESS.
- QUICK ACCESS is a feature that allows you to enter a specied app
or Live TV directly by pressing and holding the number buttons.
Audio descriptions function will be enabled.
Adjusts the volume level.
(MUTE) Mutes all sounds.
(MUTE) Accesses the [Accessibility] menu.
Scrolls through the saved programmes.
(Voice recognition) Network connection is required to use the
voice recognition function. Once the voice display bar is activated on
the TV screen, press and hold the button and speak your command
out loud.
(HOME) Accesses the Home menu.
(HOME) Shows the previous history.
(Q. Settings) Accesses the Quick Settings.
(Q. Settings) Displays the [All Settings] menu.
Wheel (OK) Press the center of button to select a menu. You
can change programmes by using button.
(up/down/left/right) Press the up, down, left or right
button to scroll the menu. If you press buttons while the
pointer is in use, the pointer will disappear from the screen and Magic
Remote will operate like a general remote control. To display the
pointer on the screen again, shake Magic Remote to the left and right.
/ Returns to the previous level.
/
Clears on-screen displays and returns to last input
viewing.
/ Shows programme guide.
Using Magic Remote
Control
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
When the message [Magic Remote battery is low. Please change the
battery.] is displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA)
matching the and ends to the label inside the compartment,
and close the battery cover. Be sure to point the magic remote toward
the remote control sensor on the TV. To remove the batteries, perform
the installation actions in reverse.
1
1
1
1
1
(Some buttons and services may not be provided depending on models
or regions.)
11
ENGLISH
1
Streaming Service buttons Connects to the Video Streaming
Service.
(INPUT) Changes the input source.
(INPUT) Accesses the [HOME DASHBOARD].
Displays the set-top box Home menu.
- When you are not watching via a set-top box: the display changes
to the set-top box screen.
, , , These access special functions in some
menus.
Runs the record function.
, (Control buttons) Controls media contents.
Registering Magic Remote Control
How to register the Magic Remote Control
To use the Magic Remote, rst pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the Wheel (OK) on
the remote control.
* If the TV fails to register the Magic Remote, try again after turning
the TV off and back on.
How to deregister the Magic Remote
Control
Press the / and (HOME) buttons at the same time, for
ve seconds, to unpair the Magic Remote with your TV.
* Pressing and holding the / button will let you cancel and
re-register Magic Remote at once.
•  It is recommended that an Access Point (AP) be located
more than 0.2 m away from the TV. If the AP is installed
closer than 0.2 m, the Magic remote control may not
perform as expected due to frequency interference.
•  Do not mix new batteries with old batteries. This may
cause the batteries to overheat and leak.
•  Failure to match the correct polarities of the battery
may cause the battery to burst or leak, resulting in re,
personal injury, or ambient pollution.
•  This apparatus uses batteries. In your community there
might be regulations that require you to dispose of these
batteries properly due to environmental considerations.
Please contact your local authorities for disposal or
recycling information.
•  Batteries inside or inside the product shall not be
exposed to excessive heat such as sunshine, re or the
like.
User Guide
For more information about this TV, read the USER GUIDE embedded in
the product.
To open the USER GUIDE ( ) [General] [About
This TV] [User Guide]
12
ENGLISH
Troubleshooting
Cannot control the TV with the remote control.
Check the remote control sensor on the product and try again.
Check if there is any obstacle between the product and the remote
control.
Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
Check if the product is turned on.
Check if the power cord is connected to a wall outlet.
Check if there is a problem in the wall outlet by connecting other
products.
The TV turns o suddenly.
Check the power control settings. The power supply may be
interrupted.
Check if the auto-o function is activated on the settings related
time.
If there is no signal while the TV is on, the TV will turn o
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), no signal is detected.
Turn the TV o/on using the remote control.
Reconnect the HDMI cable.
Restart the PC with the TV on.
Abnormal Display
If the product feels cold to the touch, there may be a small “icker”
when it is turned on. This is normal, there is nothing wrong with
product.
This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (white,
red, blue or green) at a size of 1ppm on the panel. This does not
indicate a malfunction and does not aect the performance and
reliability of the product.
This phenomenon also occurs in third-party products and is not
subject to exchange or refund.
You may nd dierent brightness and colour of the panel
depending on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel.
It is not related with the product performance, and it is not
malfunction.
Generated Sound
“Cracking noise: A cracking noise that occurs when watching or
turning o the TV is generated by plastic thermal contraction due
to temperature and humidity. This noise is common for products
where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a
large amount of current to operate a product. It varies depending
on the product.
This generated sound does not aect the performance and
reliability of the product.
•  Make sure to wring any excess water or cleaner from
the cloth.
•  Do not spray water or cleaner directly onto the TV screen.
•  Make sure to spray just enough of water or cleaner onto a
dry cloth to wipe the screen.
13
ENGLISH
Specications
(Depending on country)
Broadcasting Specifications
Digital TV Analogue TV
Television system DVB-T/T2, DVB-C, DVB-S/S2
PAL B/B, PAL B/G, PAL
D/K, PAL-I,
SECAM B/G, SECAM D/K,
NTSC-M
Channel coverage
(Band)
DVB-S/S2* DVB-C* DVB-T/T2*
46 ~ 862 MHz
950 ~ 2,150 MHz 46 ~ 890 MHz
VHF III : 174 ~ 230 MHz
UHF IV : 470 ~ 606 MHz
UHF V : 606 ~ 862 MHz
S Band II : 230 ~ 300 MHz
S Band III : 300 ~ 470 MHz
Maximum number of
storable programmes
6,000 3,000
External antenna
impedance
75 Ω
CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm
* Only DVB-T2/C/S2 support model only.
Wireless module (LGSBWAC92) Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range Output Power (Max.)
2,400 to 2,483.5 MHz
5,150 to 5,725 MHz
5,725 to 5,850 MHz (Not for EU)
18 dBm
18 dBm
12 dBm
Bluetooth
Frequency Range Output Power (Max.)
2,400 to 2,483.5 MHz 8 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is congured for the regional
frequency table.
For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.
* IEEE 802.11ac is not available in all countries.
Environment condition
Operating Temperature 0 °C to 40 °C
Operating Humidity Less than 80 %
Storage Temperature -20 °C to 60 °C
Storage Humidity Less than 85 %
14
ENGLISH
Open Source Software
Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
This oer is valid for a period of three years after our last shipment of
this product. This oer is valid to anyone in receipt of this information.
Licenses
(Magic Remote supported models only)
15
ENGLISH
Important Information for
Preventing Image Retention
OLED is a self-emissive technology, which brings many signicant
benets to image quality and performance. As with any self-emitting
display, it is possible for users of OLED TVs to experience temporary
image retention under certain conditions, such as when displaying a
static image on the screen for a long time. LG OLED TVs incorporate
dedicated functions that protect the screen from possible image
retention.
If a static image persists on screen, screen brightness is automatically
reduced in specic areas of, or across the entire screen. Once the static
image disappears, screen brightness will automatically return to its
prior setting. This is not a product malfunction.
Examples of Images that may Cause
Image Retention
Still images or xed images containing certain information
that are displayed uninterrupted on the screen, such as channel
numbers, station logos, program titles, news or movie subtitles,
and headlines.
Fixed menu or icons for video game consoles or broadcasting
set-top boxes.
Black bars shown on the left, right, top, or bottom of the screen,
such as in images with a 4:3 or 21:9 ratio.
Recommended Measures for
Preventing Image Retention
Avoid watching a video displaying an image as listed above for
extended periods of time.
Adjust your TV settings as below when turning on a video
exhibiting an image as listed above for extended periods of time.
- [Picture] [Picture Mode Settings] [Picture Mode]
[Eco]
- [Picture] [Picture Mode Settings] [OLED LIGHT] Adjust
to lower value
- [Picture] [Additional Settings] [OLED Panel Settings]
[Logo Luminance Adjustment] [High]
Turn o the menu bar of an external device, such as a set-top
box, to prevent long-term display of the menu bar of such device.
(Please refer to the manual of the applicable external device for
instructions.)
Adjust the settings as below when watching a video constantly
showing black bars on the left, right, top or bottom, in order to
remove the black bars.
- [Picture] [Aspect Ratio Settings] [Aspect Ratio]
[Vertical Zoom] or [All-Direction Zoom]
Information on Functions
Supporting Image Quality in
Relation to Temporary Image
Retention
LG OLED TVs provide a feature called Pixel Refresher, which helps to
prevent temporary image retention.
When the accumulated television viewing time reaches 2,000
hours or more (this is equivalent to watching TV for ve hours a
day over the course of a year), Pixel Refresher will be automatically
activated once your TV is turned o. When turning o your TV, a
notice will appear on the screen informing the activation of Pixel
Refresher. This feature will run for an hour while your TV is turned
o. A horizontal line may appear at the top or bottom of the screen
when the process is almost nished.
You may also manually activate Pixel Refresher via the TV menu:
( ) [Picture] [Additional Settings] [OLED
Panel Settings] [Pixel Refresher].
Whenever you watch your TV for more than four cumulative hours,
Pixel Refresher will be automatically activated for a few minutes
once your TV is turned o. (Note: Pixel Refresher will not be
activated if the power cord of your TV is not plugged in or the main
power is o.)
The model and serial number of the product are located
on the back and on one side of the product. Record them
below in case you ever need service.
Model
Serial No.
www.lg.com
Copyright © 2019 LG Electronics Inc. Tous droits réservés.
Veuillez lire attentivement ce manuel avant de mettre en
service votre produit et conservez-le an de pouvoir vous y
référer ultérieurement.
MANUEL D’UTILISATION
Sécurité et référence
2
Avertissement! Consignes
de sécurité
AVERTISSEMENT
RISQUE D'ÉLECTROCUTION.
NE PAS OUVRIR.
AVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE D'ÉLECTROCUTION,
NE RETIREZ PAS LE CAPOT (OU L'ARRIÈRE). AUCUNE PIÈCE N'EST
RÉPARABLE PAR L'UTILISATEUR LUI-MÊME. CONFIEZ L'ENTRETIEN
DE CET APPAREIL À UN PERSONNEL QUALIFIÉ.
Ce symbole est destiné à prévenir l'utilisateur de la
présence d'une «tension dangereuse» non isolée dans le
boitier du produit. Cette tension peut être d'amplitude susante
pour constituer un risque d'électrocution.
Ce symbole est destiné à prévenir l'utilisateur que des
instructions importantes sur le fonctionnement et
l’entretien (réparation) de l'appareil se trouvent dans la
documentation.
AVERTISSEMENT: AFIN DE RÉDUIRE LE RISQUE D'INCENDIE ET
D'ÉLECTROCUTION, N'EXPOSEZ PAS LE PRODUIT À LA PLUIE OU À
L'HUMIDITÉ.
POUR PRÉVENIR TOUT RISQUE D’INCENDIE, VEUILLEZ MAINTENIR
LES BOUGIES OU AUTRES OBJETS IMFLAMMABLES ÉLOIGNÉS DE CE
PRODUIT EN TOUT TEMPS.
N’installez pas la TV et la télécommande dans les
environnements suivants:
- Évitez d’exposer l’appareil à la lumière directe du soleil.
- Une zone fortement humide comme une salle de bain
- À proximité d’une source de chaleur comme une cuisinière et
tout autre appareil produisant de la chaleur.
- À proximité d’un plan de travail de cuisine ou d’un
humidicateur où elles pourraient facilement être exposées à la
vapeur ou à l’huile.
- Une zone exposée à la pluie et au vent.
- Ne placez pas d'objets contenant du liquide (tel qu'un vase, une
tasse, etc.) sur ou au-dessus de ce produit (par exemple, sur une
étagère au-dessus de l'unité).
- N'installez pas le téléviseur à proximité d'objets inammables,
comme de l'essence ou des bougies. N'exposez pas directement
le téléviseur à l'air conditionné.
- N'installez pas l'appareil dans un endroit excessivement
poussiéreux.
Le non-respect de cette consigne peut provoquer un incendie, un
choc électrique, une combustion/explosion, un dysfonctionnement
ou une déformation du produit.
Ventilation
- Installez le téléviseur dans un endroit bien aéré. Évitez les
espaces fermés, tels qu'un meuble de bibliothèque.
- N’installez pas le produit sur un tapis ou un coussin.
- Évitez de bloquer ou de couvrir le produit avec un tissu ou autre
matériau lorsque l'unité est branchée.
Évitez de toucher les ouvertures de ventilation. Lors de l'utilisation
prolongée du téléviseur, les ouvertures de ventilation peuvent
surchauer.
Protégez le câble d’alimentation contre les mauvais traitements
physiques ou mécaniques, la torsion, la pliure, le pincement, et
évitez qu’il ne puisse être pris dans une porte ou que l’on puisse
marcher dessus. Vériez soigneusement les ches, les prises
murales et les points de sortie du cordon de l'appareil.
Ne déplacez pas le téléviseur tant que le cordon d'alimentation
est branché.
N'utilisez pas de cordon d'alimentation endommagé ou déformé.
Veillez à tenir le cordon d'alimentation par la che pour le
débrancher. Ne tirez pas sur le cordon d'alimentation pour
débrancher le téléviseur.
Ne branchez pas trop d'appareils à la même prise secteur pour
éviter les risques d'incendie ou de choc électrique.
Déconnexion de l'appareil de l'alimentation principale
- La che d'alimentation est l'élément de déconnexion. En
cas d'urgence, la che d'alimentation doit rester facilement
accessible.
Ne laissez pas les enfants grimper sur la TV ou s’agripper dessus.
Dans le cas contraire, la TV risque de tomber ce qui peut entraîner
des blessures graves.
Mise à la terre de l'antenne extérieure (peut varier selon le
pays):
- Si une antenne extérieure est installée, respectez les précautions
suivantes. Un système d'antenne extérieure ne doit pas être
installé à proximité de lignes électriques aériennes ou autres
lumières ou circuits électriques. Il ne doit pas entrer en contact
avec des lignes ou circuits électriques au risque d'entraîner un
décès ou des blessures graves.
Assurez-vous que le système d'antenne est mis à la terre
pour assurer une certaine protection contre les surtensions et
l'accumulation des charges statiques. La section810 du National
Electrical Code (NEC) aux États-Unis fournit des informations
concernant la mise à la terre correcte de l'antenne et de la
structure porteuse, la mise à la terre du câble d'entrée à une
unité de décharge d'antenne, la taille des conducteurs de terre,
l'emplacement de l'unité de décharge d'antenne, la connexion
et les prérequis des électrodes de terre. Mise à la terre d'une
antenne selon le National Electrical Code, ANSI/NFPA70
FRANÇAIS
3
Mise à la terre (ne s'applique pas aux appareils ne nécessitant
pas de mise à la terre)
- Un téléviseur muni d'une che électrique secteur mise à la terre
avec trois broches doit être branché sur une prise secteur mise à
la terre avec trois broches. Veillez à brancher le câble de mise à la
terre pour éviter les chocs électriques.
Ne touchez jamais cet appareil ou cette antenne pendant un orage.
Vous pourriez vous électrocuter.
Assurez-vous que le cordon d'alimentation est bien branché
au téléviseur et à la prise murale. Si ce n'est pas le cas, la che
d'alimentation et la prise risquent d'être endommagées. Dans des
situations extrêmes, un incendie peut se déclarer.
N'insérez pas d'objets métalliques ou inammables dans le
produit. Si un corps étranger tombe dans le produit, débranchez le
cordon d'alimentation et contactez le service client.
Ne touchez pas le bout du cordon d'alimentation lorsqu'il est
branché. Vous risqueriez de subir un choc électrique.
Si vous êtes confronté à l'une des situations suivantes,
débranchez immédiatement le produit et contactez votre
service client local.
- Le produit a été endommagé.
- Si de l'eau ou une autre substance pénètre dans le produit
(adaptateur secteur, cordon d'alimentation ou téléviseur).
- Si vous sentez de la fumée ou toute autre odeur émanant du
téléviseur
- Pendant les orages ou lorsque l'appareil n'est pas utilisé
pendant un long moment.
Même si le téléviseur est éteint via la télécommande ou un
bouton, l'alimentation secteur est connectée à l'unité si elle n'est
pas débranchée.
N'utilisez pas d'appareil électrique à haute tension à proximité du
téléviseur (par exemple, un tue-mouches électrique). Cela pourrait
endommager le produit.
N'essayez pas de modier ce produit sans une autorisation écrite
de LGElectronics. Un incendie accidentel ou un choc électrique
peuvent se produire. Contactez votre service client local pour tout
service ou réparation. Des modications non autorisées peuvent
annuler le droit de l'utilisateur à utiliser ce produit.
Utilisez uniquement des pièces/accessoires approuvés par
LGElectronics. Le non-respect de cette consigne peut provoquer
un incendie, un choc électrique, un dysfonctionnement ou des
dommages au produit.
Ne démontez pas l’adaptateur secteur ou le câble d’alimentation.
Le non-respect de cette consigne peut provoquer un incendie ou
une électrocution.
Manipulez l'adaptateur avec précaution pour éviter de le faire
tomber ou de l'abîmer. Un impact pourrait endommager
l'adaptateur.
Pour réduire les risques d'incendie ou de choc électrique, ne
touchez pas le téléviseur avec les mains mouillées. Si le cordon
d'alimentation est mouillé ou couvert de poussière, séchez
intégralement la prise d'alimentation ou essuyez la poussière.
Batteries
- Rangez les accessoires (batterie, etc.) dans un endroit sûr hors
de portée des enfants.
- Ne court-circuitez pas les batteries, ne les démontez pas et ne
les laissez pas surchauer. Ne jetez pas les batteries dans un feu.
N’exposez pas les piles à une température excessive.
- Avertissement: Risque d´incendie ou d´explosion si la batterie
est remplacée par un autre modèle de batterie inadapté.
Déplacement
- Lorsque vous déplacez le produit, assurez-vous qu'il est éteint,
débranché et que tous les câbles ont été retirés. Il faut deux
(2) personnes ou plus pour porter un téléviseur de grande
taille. Ne vous appuyez pas sur le panneau avant du téléviseur
et n'appliquez aucune pression dessus. Vous risqueriez
d'endommager le produit ou de vous exposer à un risque
d'incendie ou de blessure.
Ne laissez pas le matériau d'emballage anti-humidité ou
l'emballage en vinyle à la portée des enfants.
Évitez tout impact ou chute d'objets sur l'appareil, et ne laissez
rien tomber sur l'écran.
N’appuyez pas fortement sur le panneau avec la main ou un
objet pointu tel qu'un clou, un crayon ou un stylo. Ne rayez pas le
panneau. Cela risquerait d'endommager l'écran.
Nettoyage
- Lorsque vous nettoyez le produit, débranchez le cordon
d'alimentation et essuyez délicatement la surface avec un
chion doux et sec. Ne pulvérisez pas d'eau ou autre liquide
directement sur le téléviseur. N’utilisez jamais de produit
pour vitre, de désodorisant, d’insecticide, de lubriant, de cire
pour voiture ou industrielle, d’abrasif, de diluant, de benzène,
d’alcool, etc., car ces produits risqueraient d’endommager le
produit et / ou son écran. Le non-respect de cette consigne peut
provoquer un choc électrique ou endommager le produit.
FRANÇAIS
4
Préparation
Si le téléviseur est mis sous tension pour la première fois depuis
son expédition depuis l’usine, l’initialisation peut prendre quelques
minutes.
Limage présentée peut être diérente de votre téléviseur.
L’achage à l’écran de votre TV peut diérer légèrement de celui
qui est présenté dans ce manuel.
Les menus et options disponibles peuvent être diérents selon la
source d’entrée ou le modèle de produit utilisé.
De nouvelles fonctionnalités pourront être ajoutées ultérieurement
à ce téléviseur.
Le téléviseur doit être raccordé à une prise électrique facile d'accès
située à proximité. Le bouton marche/arrêt n'est pas présent sur
tous les modèles de produit. Pour éteindre ces appareils, il est
nécessaire de débrancher le cordon d'alimentation.
Les éléments fournis avec votre produit dièrent en fonction du
modèle choisi.
Les caractéristiques des produits ou le contenu de ce manuel
peuvent être modiés sans préavis en cas de mise à jour des
fonctions.
Pour une connexion optimale, les câbles HDMI et les périphériques
USB doivent comporter des connecteurs d’une épaisseur inférieure
à 10mm et d’une largeur inférieure à 18mm. Utilisez une rallonge
prenant en charge si le câble USB ou la clé USB ne s’adapte
pas au port USB de la TV.
A
B
A
B
* A 10 mm
* B 18 mm
Utilisez un câble certié sur lequel est apposé le logo HDMI.
Si vous utilisez un câble non certié HDMI, l’écran peut ne pas
s’acher ou une erreur de connexion peut survenir. (Types de
câbles HDMI recommandés)
- CâbleHDMI®/
TM
ultra haut débit (max. 3m)
Achat séparé
Des articles vendus séparément peuvent faire l’objet de remplacements
ou de modications sans préavis dans le but d’améliorer la qualité du
produit. Contactez votre revendeur pour vous procurer ces articles. Ces
périphériques fonctionnent uniquement avec certains modèles.
Le nom ou le design du modèle peut changer en cas de mise à niveau
des fonctions du produit, des conditions de diusion ou des politiques
de condentialité du fabricant.
Magic Remote
AN-MR19BA
Vériez si votre modèle de téléviseur prend en charge la
fonctionBluetooth dans les spécications du module sans l an de
vous assurer quil est compatible avec la télécommandeMagic.
Support de xation murale
(Selon le modèle)
Veillez à utiliser des vis et un support mural conformes aux normes
VESA. Les dimensions standard des kits de support mural sont indiquées
dans le tableau suivant.
A
B
Modèle
OLED55/65B9*
OLED55/65C9*
OLED55/65E9*
OLED77B9*
OLED77C9*
VESA (A x B) (mm) 300 x 200 400 x 200
Vis standard M6 M6
Nombre de vis 4 4
Support mural OLW480B OLW480B
FRANÇAIS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

LG OLED77C9PLA Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues