©2007 Stillwater Designs
ZX
SUBWOOFERAMPLIFIER
CLASS-DMONOCHANNEL
ZX1000.1, ZX1500.1, ZX2500.1
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least
4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled
passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to
mount the amplifi er.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to
the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er,
the ZX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the
source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the
RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Either input method will provide a
low-level output signal at the RCA output, which effectively passes the audio signal to another amplifi er
or component. Keep the audio signal cable away from factory wiring harnesses and other power wiring.
If you need to cross this wiring, cross it at a 90 degree angle.
Install the provided external fuse within 18” (45cm) of the ZX amplifi er and in-line with the power cable.
Install a second fuse within 18” (45cm) of the battery and in-line with the power cable connected to your
amplifi er. These ZX series mono amplifi ers deliver Kilo-Watts of power. We recommend an alternator
with a minimum 140 ampere output capacity, at least one extra battery located within 50” (130cm) to
the amplifi er, an extra fuse located within 18” (45cm) of the extra battery, all power and ground feeds
to be as short as possible, and utilize 12, 10 or 8 gauge speaker wire. See Figure 2. If you ever need
to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it. See the chart below for
power and ground wire size, and fusing recommendations.
ZX.1SeriesAmplifi er
Owner’sManual
MonoChannel: ZX1000.1 / ZX1500.1 / ZX2500.1
Authorized Kicker Dealer:
Purchase Date:
Amplifi er Model Number:
Amplifi er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INSTALLATION
2
ZX.1AMPLIFIER
CONFIGURATION
3
+12V
18"
(45cm)
24"
(60cm)
KUNEK
10 - COMA
Figure 2
Minimum impedance of 2 ohms while in bridged operation
Ground
Remote
Turn-On
Fuse
Battery
One Channel Operation (Mono)
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
+
+
>
+
>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Amplifi er
To Source Unit
Figure 1
ModelZX1000.1 1 (ONE) 100 AMPERE FUSE PowerGroundWire 1/0GA
ModelZX1500.1 1 (ONE) 150 AMPERE FUSE PowerGroundWire 1/0GA
ModelZX2500.1 1 (ONE) 300 AMPERE FUSE PowerGroundWire 1/0GA
Signal In
Signal Out
Source Unit
Performance
Model ZX1000.1 ZX1500.1 ZX2500.1
RMS Power in Watts, all channels driven @14.4
Volts, 4Ω mono, ≤ 1% THD+N
500 x 1 750 x 1 1250 x 1
@ 2Ω mono, ≤ 1.5% THD+N 1000 x 1 1500 x 1 2500 x 1
Length: in(cm) 16 3/4 (42.5) 20 (50.7) 27 1/2 (69.7)
Specifi cations common to all models:
Height: in(mm) 2 1/8 (54mm)
Width: in(mm) 9 5/8 (244mm)
Frequency Response, ± 1 db: 25 Hz - 200 Hz
Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity:
Low Level: 125mV-5V
High Level: 250mV-10V
Selectable Electronic Crossover: Variable Low-Pass, 50 - 200Hz, 24dB per octave
Subsonic Filter 24 db/Octave Subsonic Filter Fixed @ 25Hz
Bass Boost: Variable 0-18db Bass Boost @ 40Hz
3. Confi guration The following diagram shows the most common confi gurations for your Kicker ZX
series amplifi er.
One Channel Operation These ZX amplifi ers are capable of operating into a minimum impedance of
2 ohms. If you are using multiple voice coils, the net impedance of the voice coils must be equal to or
greater than 2 ohms.
Operation
1. Automatic Turn-On Selection The ZX series offers three different automatic turn-on modes that can
be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode
causes the REM terminal to have +12V out for turning on additional amplifi ers.
Remote Turn-On Set the switch to +12V to use the remote turn-on lead from your source unit. Run
18 Ga wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the
amplifi er’s positive and negative power terminals. This is the preferred automatic turn-on method.
DC Offset Turn-On If Remote Turn-On is not an option, the next best setting is DC Offset. The DC
Offset mode detects a 6 volt surge from the HI Level speaker outputs when the source unit has been
turned on.
Signal Sense Turn-On The Audio setting is the fi nal alternative for Automatic turn-on. This is a Signal
Sense turn-on method that detects the incoming audio signal from your source unit and automatically
turns on the amp. This turn-on method will not work properly if the input gain control is not set
appropriately.
2. Input Level The RCA inputs on Kicker ZX amplifi ers are capable of receiving either Hi or Low-level
signals from your source unit. If the only output available from your source unit is a Hi-Level signal,
simply press in the Input Level switch on the amplifi er. Refer to the wiring section of this manual for more
detailed instructions.
3. Input Gain Control The input gain control is not a volume control. It matches the output of the
source unit to the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear
audible distortion, then turn it down a little.
4. Bass Boost Control The variable bass boost control on the top of the amplifi er is designed to give
you increased output 0 - 18dB at 40 Hz. The setting for this control is subjective. If you turn it up, you
must go back and adjust the input gain control to avoid clipping the amplifi er.
5. Crossover Control The variable crossover on the top of the amplifi er allows you to adjust the
crossover frequency from 50-200Hz. The setting for this control is subjective; 80Hz is a good place to
start.
6. RemoteBass(Level Control) With the remote
bass level control, you have the ability to control
the output level of the amplifi er remotely. To
mount the remote bass level control, simply
screw the metal bracket to the chosen location.
Then slide the housing onto the bracket until
it snaps into place. Run the cable from the
controller to the “Remote Bass” jack on the
amplifi er chassis.
TroubleShooting
If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses,
poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There
is an illuminated red badge on top of the amplifi er denoting the power state of the amp in addition to
the Protection LED on the end panel of your Kicker ZX series amplifi er. When the red badge is lit this
indicates the amplifi er is turned on and the amplifi er is functioning properly.
RED Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt
power terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)
3) Check for reversed power and ground connections. 4) Ground terminal, for proper conductivity. 5)
Check for blown fuses.
OPERATION
ZX.1AMPLIFIER
4
RED Badge Light on, no output? Check the following: 1) RCA connections 2) Test speaker
outputs with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4)
Check for a signal in the RCA cable feeding the amplifi er with the VOM meter set to measure “AC”
voltage.
End Panel LED fl ashing with loud music? The yellow LED indicates low battery voltage. Check
all the connections in your vehicle’s charging system. It may be necessary to replace or charge your
vehicle’s battery or replace your vehicle’s alternator.
End Panel LED on, no output? 1) Amplifi er is very hot. Thermal protection is engaged. Test for
proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for
minimum recommended impedance and multiple speaker wiring suggestions). Also check for adequate
airfl ow around the amplifi er. 2) Amplifi er shuts down only while vehicle is running. Voltage protection
circuitry is engaged. Voltage to the amplifi er is not within the 9-16 volt operating range. Have the vehicle’s
charging and electrical system inspected. 3) Amplifi er will only play at low volume levels. Short circuit
protection is engaged. Check for speaker wires shorted to each other or to the vehicle chassis. Check
for damaged speakers, or speaker(s) operating below the minimum recommended impedance.
No or Low Output? 1) Check the balance and fader control on source unit 2) Check the RCA (or
speaker input) and speaker output connections
Reduced Bass Response? Check system phasing by reversing a speaker connection from positive to
negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper
grounding 4) Check the gain settings and turn them down if they are set too high.
Ground Noise? Kicker amplifi ers are engineered to be fully compatible with all manufacturers’ head
units. Some head units may require additional grounding to prevent noise from entering the audio signal.
If you are experiencing this problem with your head unit, in most cases running a ground wire from the
RCA outputs on the head unit to the chassis will remedy this issue.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are
correct. Improper connections can result in blown amplifi er fuses as well as the failure of other critical
systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the
Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on
the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab,
choose the subject you are interested in, and then download or view the corresponding information.
Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specifi c
questions.
PERFORMANCE
5
AUTO
TURN ON
INPUT
LEVEL
LR
SPKR +
SPKR -
INPUT
REMOTE BASS
OUTPUT
LO
HI
LR
+12V
DC
OFFSET
AUDIO
Model ZX1000.1
500 x 1 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -62 CEA-2006 (ref: 1W, A-weighted)
AUTO
TURN ON
INPUT
LEVEL
L
R
L
INPUT
OUTPUT
R
SPKR +
SPKR -
+12V
DC
OFFSET
AUDIO
LO
HI
REMOTE BASS
Slide the housing until it snaps into the metal bracket
4 Conductor
Phone Cable
Back View
Side View
Mount the metal bracket
Model ZX1500.1
750 x 1 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -55 CEA-2006 (ref: 1W, A weighted)
Model ZX2500.1
1500 x 1 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -50 CEA-2006 (ref: 1W, A-weighted)
WARRANTY
ZX.1AMPLIFIER
6
ElectronicsLimitedWarranty
Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is
warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original receipt.
Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the
warranty period, Kicker will repair or replace (at its discretion) the defective merchandise with equivalent merchandise at
no charge. Warranty replacements may have cosmetic scratches and blemishes. Discontinued products may be replaced
with more current equivalent products.
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to
the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty
as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or
implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore these
exclusions may not apply to you. This warranty gives you specifi c legal rights; however you may have other rights that
vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Defective merchandise should be returned to your local Authorized Stillwater Designs (Kicker) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater
Designs directly. You can confi rm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (Kicker), call the Kicker
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package all
defective items in the original container or in a package that will prevent shipping damage, and return to:
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return-only defective components. The
return of functioning items increases your return freight charges. Non-defective items will be returned freight-collect to
you.
Include a copy of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing
the Customer’s name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without
proof-of-purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid;
items sent freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed.
It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be considered
abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifi er clipping or distortion
o Items previously repaired or modifi ed by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products returned without a Return Merchandise Authorization (RMA) number
o Freight Damage
o The cost of shipping product to Kicker
o Service performed by anyone other than Kicker
HOW LONG WILL IT TAKE?
Kicker strives to maintain a goal of 72-hour service for all electronics (amplifi ers, crossovers, equalizers, etc.) returns.
Delays may be incurred if lack of replacement inventory or parts is encountered.
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service
Department at (405) 624-8510.
NOTE: All specifi cations and performance fi gures are subject to change. Please visit the www.kicker.com for the most current information.
InternationalWarranty
Contact your International Kicker dealer or distributor concerning specifi c procedures for your country’s warranty policies.
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning
up a system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at
the same volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently
damage your hearing. Please use common sense when controlling volume.
GARANTÍA INTERNACIONAL VersiónEspañol
Comuníquese con su concesionario o distribuidor Kicker internacional para obtener infor ación sobre procedimientos
específi cos relacionados con las normas de garantía de su país.
ADVERTENCIA: Los excitadores Kicker son capaces de producir niveles de sonido que pueden dañar permanentemente
el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el oído que escuchar un
sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es muy fuerte y que puede
dañar permanentemente el oído. Sea precavido cuando controle el volumen.
La frase “combustible para vivir la vida Livin’ Loud™ a todo volumen” se refi ere al entusiasmo por la vida que la marca
Kicker de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible (“a
todo volumen”) en todo sentido. La línea de altavoces y amplifi cadores Kicker es la mejor del mercado de audio de
automóviles y por lo tanto representa el “combustible” para vivir a todo volumen en el área de “estéreos de automóvil” de
la vida de nuestros clientes. Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos
locales sobre ruido en cuanto a los niveles legales y apropiados de audición fuera del vehículo.
INTERNATIONALE GARANTIE DeutscheVersion
Nehmen Sie mit Ihren internationalen Kicker-Fachhändler oder Vertrieb Kontakt auf, um Details über die Garantieleistungen
in Ihrem Land zu erfahren.
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann!
Wenn Sie ein System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein
nicht verzerrtes System auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass der
Schallpegel zu laut ist und zu permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung bitte
vernünftig!
Der Slogan “Treibstoff für Livin’ Loud” bezieht sich auf die mit den Kicker-Autostereosystemen assoziierte Lebensfreude
und die Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten (“Livin’ Loud”) zu
streben. Die Lautsprecher und Verstärker von Kicker sind auf dem Markt für Auto-Soundsysteme führend und stellen somit
den “Treibstoff” für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren Kunden, sich bezüglich der
zugelassenen und passenden Lautstärkepegel außerhalb des Autos an die örtlichen Lärmvorschriften zu halten.
GARANTIE INTERNATIONALE VersionFrançaise
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou distributeur
International Kicker.
AVERTISSEMENT: Les haut-parleurs Kicker ont la capacité de produire des niveaux sonores pouvant endommager
l’ouïe de façon irréversible ! L’augmentation du volume d’un système jusqu’à un niveau présentant une distorsion audible
endommage davantage l’ouïe que l’écoute d’un système sans distorsion au même volume. Le seuil de la douleur est
toujours le signe que le niveau sonore est trop élevé et risque d’endommager l’ouïe de façon irréversible. Réglez le volume
en faisant prevue de bon sens !
L’expression “ carburant pour vivre plein pot “ fait référence au dynamisme de la marque Kicker d’équipements audio
pour véhicules et a pour but d’encourager nos clients à faire le maximum (“ vivre plein pot “) dans tous les aspects de leur
vie. Les haut-parleurs et amplifi cateurs Kicker sont les meilleurs dans le domaine des équipements audio et représentent
donc pour nos client le “ carburant pour vivre plein pot “ dans l’aspect “ installation audio de véhicule “ de leur vie.
Nous encourageons tous nos clients à respecter toutes les lois et réglementations locales relatives aux niveaux sonores
acceptables à l’extérieur des véhicules.
GARANTIE
7
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510
10262007-E+08ZX.1
-
1
-
2
-
3
-
4
Kicker ZX1500.1 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Kicker ZX1500.1 Owner's manual
Documents connexes
-
Kicker 2008 ZX300.1 Owners Le manuel du propriétaire
-
Kicker ZX1500.1 Le manuel du propriétaire
-
-
Kicker ZX1500.1 Le manuel du propriétaire
-
-
-
-
-
Kicker DXA1000.1 Le manuel du propriétaire
-