Simplicity 1696717-00 Manuel utilisateur

Marque: Simplicity

Modèle: 1696717-00

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Ce manuel convient également à

Not for

Reproduction

80019672USCN

Revision C

Not for

Reproduction

Manual Contents:

General Information..............................................................2

Operator Safety.....................................................................2

Features and Controls..........................................................5

Operation...............................................................................6

Maintenance and Adjustments..........................................11

Storage.................................................................................13

Troubleshooting..................................................................15

Specifications......................................................................16

General Information

For additional information, refer to the

Customer Contact Guide

and

Setup Instructions

included with the unit.

The illustrations in this document are representative. Your unit

may vary from the images shown.

LEFT

and

RIGHT

are

referenced from the operating position.

The use of Important and Note in the text indicates clarifications,

exceptions, or alternatives to the procedures given.

All language translations of this document are derived from the

original English source file.

All packaging, used oil, and batteries should be recycled

according to applicable government regulations.

Operator Safety

Save these instructions for future reference. This manual

contains safety information to make you aware of the hazards

and risks associated with the product and how to avoid them.

It also contains important instructions that should be followed

during the initial set-up, operation, and maintenance of the

product.

The snowthrower is designed and intended only for clearing of

snow from hard-surface ground-level walkways and driveways

and is not intended for any other purpose.

It is important that you read and understand these instructions

before attempting to start or operate this equipment.

Be thoroughly familiar with the controls and the proper use of

the snowthrower.

Know how to stop the unit and disengage controls quickly.

Safety Alert Symbol and Signal Words

The safety alert symbol ( ) is used to identify safety

information about hazards that can result in personal injury. A

signal word (DANGER, WARNING, or CAUTION) is used with

the alert symbol to indicate the likelihood and the potential

severity of injury. In addition, a hazard symbol may be used to

represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

indicates a situation that could result in damage to

the product.

Snowthrower Hazard Symbols

MeaningSymbolMeaningSymbol

Read and understand the

operator's manual before

operating or servicing the

unit.

Safety information about

hazards that can result

in personal injury.

Remove the key before

performing service. Read

the operator's manual

before performing service.

Amputation hazard -

rotating impeller.

Amputation hazard -

rotating auger

Amputation hazard -

rotating impeller.

Thrown objects hazard.Amputation hazard - do

not touch moving parts.

Explosion hazard.Fire hazard.

Toxic fume hazard.Shock hazard.

Kickback hazard.Hot surface hazard.

Keep children away.Keep a safe distance.

— — —— — —Wear safety glasses

Not for

Reproduction

Safety Messages

DANGER

This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so could result in

death or serious injury.

Hand contact with the rotating auger inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

WARNING

Read, understand, and follow all the instructions on the

snowthrower and in the operator's manual before operating

this unit. Failure to observe the safety instructions in this

manual could result in death or serious injury.

• Only allow operators who are responsible, trained, familiar

with the instructions and physically capable to operate

the machine.

WARNING

Always wear safety glasses or eye shields during operation

or while performing an adjustment or repair to protect eyes

from foreign objects that may be thrown from the machine.

U.S.A. Models: It is a violation of California Public Resource

Code Section 4442 to use or operate the engine on any

forest-covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as defined

in Section 4442, maintained in effective working order. Other

states or federal jurisdictions may have similar laws. Contact

the original equipment manufacturer, retailer, or dealer to obtain

a spark arrester designed for the exhaust system installed on

this engine.

WARNING

This product can expose you to chemicals including gasoline

engine exhaust, which is known to the State of California to

cause cancer, and carbon monoxide, which is known to the

State of California to cause birth defects or other reproductive

harm. For more information go to www.P65Warnings.ca.gov.

Safety Decals

To avoid injury, read and understand the safety decals on the

snowthrower before operating it. Match the call out letters in

Figure 1 to the decals listed in the accompanying table.

If any safety decals become worn, damaged, or illegible, contact

an authorized service dealer to order replacements.

Not for

Reproduction

Not for

Reproduction

Features and Controls

Match the call out letters in Figure 2 to the features and controls listed in the accompanying table.

Control Symbols and Meanings

Auger controlA

Auger— — —B

Chute Control - Handle Mount (if equipped)C

Chute Control - Chute Mount (if equipped)D

Chute Control - Switch Mount (if equipped)E

Deflector Control -Trigger or Wing KnobF

Starter buttonG

Starter ReceptacleH

Starting Instructions Decal (if equipped)— — —I

Starting Instructions Decal (if equipped)— — —J

Headlight (if equipped)— — —K

Choke closed; choke openL

Fuel Tank Cap— — —M

Oil Fill/Dipstick— — —N

Primer buttonO

On / Off switchP

Starter Cord Handle— — —Q

Oil Drain Plug— — —R

Not for

Reproduction

Operation

WARNING

This snowthrower is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous.

Remember you are responsible for your safety and those

around you.

• When leaving the operating position always disengage

the auger, turn off the engine, and remove the key. Never

leave a running machine unattended.

• Never operate the snowthrower without proper guards,

and other safety protective devices in place and working.

• Be careful when operating on or crossing gravel drives,

walks, or roads. Stay alert for hidden hazards or traffic.

• Never operate the snowthrower without good visibility or

light. Always be sure of your footing, and keep a firm hold

on the handles. Walk; never run.

• Be careful to avoid slipping or falling, especially when

operating the snowthrower in reverse.

• Be careful when operating on slopes.

• After striking a foreign object, stop the engine, remove

the wire from the spark plug, thoroughly inspect the

snowthrower for any damage, and repair the damage

before restarting and operating the snowthrower.

• Do not operate the equipment without wearing adequate

winter garments. Avoid loose fitting clothing that can get

caught in moving parts. Wear footwear that will improve

footing on slippery surfaces.

• Never touch a hot muffler or engine. Allow muffler and

engine cylinder to cool before touching.

Operating Area

1. Familiarize yourself with the area in which you plan to

operate the snowthrower. Mark off all boundaries of

walkways and driveways.

2. Ensure the area to be cleared is free of debris or objects

that could be picked up by the auger and thrown from the

chute.

WARNING

This machine is capable of throwing objects that could injure

bystanders or cause damage to buildings.

3. Before starting the engine, move the snowthrower outdoors

and away from windows and doors.

WARNING

Engines give off carbon monoxide, an ordorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors

or windows are open.

4. Ensure the operating area is clear of bystanders, especially

children.

WARNING

This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so could result in

death or serious injury.

• Keep children out of the area during operation.

• Children are often attracted to the equipment. Be mindful

of all persons present.

• Be alert and turn the unit off if bystanders enter the area.

• Use extra care when approaching blind corners, shrubs,

tress, or other objects that may obscure vision.

Starting the Engine

Checking Oil

NOTICE

The engine was shipped from the factory without oil. Before

you start the engine, ensure that you add oil according to the

instructions in this manual. If you start the engine without oil,

it will be damaged beyond repair and will not be covered under

the warranty.

Use Briggs & Stratton Synthetic 5W-30 Warranty Certified oil

for best performance. Other high-quality detergent oils are

acceptable if classified for service SG, SH, SJ or higher. Do

not use any additives.

1. Place the unit on a level surface.

2. Clean the oil fill area of any moisture or debris.

3. Remove the oil dipstick (A, Figure 3) and wipe it with a clean

cloth.

4. Insert and tighten the dipstick, then remove it again to check

the oil level. It should be at the top of the full indicator (C)

5. To add oil, pour slowly into the engine oil fill (B). Do not

overfill.

6. Wait one minute before checking the oil level.

7. When the oil level is at the top of the full indicator (C), install

and tighten the dipstick.

Not for

Reproduction

Adding Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline

• A minimum of 87 octane / 87 AKI (90 RON)

• Up to 10% ethanol is acceptable

NOTICE

Do not use unapproved gasolines, such as E15 and E85. Do

not mix oil in gasoline or modify the engine to run on alternate

fuels. Use of unapproved fuels will cause engine damage that

will not be covered under warranty.

This engine is certified to operate on gasoline. The emissions

control system for this engine is EM (Engine Modifications).

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane

/ 85 AKI (89 RON) gasoline is acceptable. To remain emissions

compliant, high altitude adjustment is required. Operation without

this adjustment will cause decreased performance, increased

fuel consumption, and increased emissions. See an authorized

service dealer for high altitude adjustment information. Operation

altitudes below 2,500 feet (762 meters) with the high altitude

adjustment is not recommended.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a fire

or explosion which could result in serve burns or death.

• Do not add fuel while engine is running. Let the engine

cool at least 2 minutes before adding fuel.

• Fill the fuel tank outdoors only, using an approved fuel

container with the unit directly on the ground.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Allow any spilled fuel to evaporate before starting the

engine.

• If fuel is spilled on clothing change clothing immediately.

1. Slowly remove the fuel cap (A, Figure 4) and fill the tank

(B) with fuel. Do not fill higher than the bottom of the fuel

tank neck (C).

2. Reinstall the fuel cap. Allow any spilled fuel to evaporate

before starting the engine.

Not for

Reproduction

Starting Engine

WARNING

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a fire

or explosion which could result in serve burns or death.

• Ensure that spark plug, muffler, fuel cap, and air cleaner

(if equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• Do not use pressurized starting fluids because their

vapors are flammable.

• Do not over-prime the engine. Follow the engine starting

instructions in this manual.

• If the engine floods, set choke (if equipped) to

OPEN/RUN position, move throttle (if equipped) to FAST

position and crank until engine starts.

1. Ensure the auger control is disengaged.

2. Insert the ignition key (A, Figure 5) and turn it to the ON

position or push in the Push/Pull key.

3. Turn the choke control (B) to the Closed position.

Note:

Choke is usually not needed when starting a warm engine.

4. Press the primer (C) two times.

Note:

Primer is usually not needed when starting a warm engine.

5. Rewind start: Firmly hold the starter cord handle (D). Pull

the handle slowly until resistance is felt, then pull rapidly.

WARNING

Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

6. Electric start: Connect the extension cord (E, Figure 6) to

the starter box (F) on the engine and then to the wall

receptacle. Press the starter box pushbutton (G). After the

engine starts, disconnect the extension cord from the wall

receptacle and then from the starter box.

WARNING

Damaged or ungrounded power cords could cause electric

shock. Electric shock could cause severe burns or death.

• Use only a three-conductor power cord properly

grounded to the power source.

• If the extension cord is damaged, it must be replaced

by the manufacturer or its service agent or a similarly

qualified person.

NOTICE

To extend the life of the starter, use short starting

cycles (five seconds maximum). Wait one minute between

starting attempts.

If the engine does not start after repeated attempts, contact

an authorized service dealer or go to our website.

7. Allow the engine to warm up for several minutes. Gradually

move the choke control to the Open position.

Not for

Reproduction

Stopping the Engine

1. Turn the ignition key (A, Figure 5) to the OFF position and

remove it or remove the Push /Pull key, if equipped.

2. Keep the key in a safe place out of the reach of children.

The engine cannot be started without the key.

Adjusting the Discharge Chute and

Deflector

WARNING

Ice, gravel, or other unintended objects can be picked up by

the auger and thrown from the chute with force.

Objects thrown from the chute could cause death, serious

injury, or property damage.

• Always be aware of the direction the snow is being thrown.

NOTICE

Do not use the chute deflector or the chute rotation

handle to lift the unit. These were designed for making needed

adjustment only.

Chute Rotation - Handle Mount (if equipped)

1. Squeeze and hold the button on the chute control handle

(C, Figure 7).

2. Push the handle forward or pull it rearward to rotate the

chute.

3. Release the button to lock the chute in the desired position.

NOTICE

Do not use excessive force when trying to operate

the control.

Chute Rotation - Chute Mount (if equipped)

1. Grasp the chute control handle at the base of the chute (D,

Figure 7).

2. Turn the handle left or right to rotate the chute. A tension

plate holds the chute in the desired position.

Chute Rotation - Switch Mount (if equipped)

1. Press the switch (E, Figure 7) to rotate the chute.

2. Release the switch to lock the chute in the desired position.

Deflector Adjustment

1. Squeeze and hold the button on the deflector control handle

(F, Figure 7), or loosen the wing knob (F).

2. Move the deflector up or down to adjust the snow discharge

height and distance.

3. Release the button to lock the deflector in the desired

position, or tighten the wing knob.

Not for

Reproduction

Engaging the Auger

DANGER

The discharge chute contains a rotating auger to throw snow.

Fingers or feet can quickly become caught in the auger

resulting in traumatic amputation or severe laceration.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

1. Pull the auger control (A, Figure 8) against the handle to

engage the auger.

2. Release the auger control to disengage the auger. The

auger must stop within 5 seconds after the auger control is

released. If it does not;

• Adjust the control cable. See Adjusting the Auger

Control Cable.

• If the auger still does not stop within 5 seconds, see an

authorized dealer.

NOTICE

Do not overload the machine capacity by attempting

to clear snow at too fast of a rate.

Not for

Reproduction

Clearing a Clogged Discharge Chute

DANGER

The discharge chute contains a rotating auger to throw snow.

Fingers can quickly become caught in the auger resulting in

traumatic amputation or severe laceration. Never clear a

clogged discharge chute with your hands. Always use a

clean-out tool.

To safely clear a clogged discharge chute, follow these

instructions:

1. Stop the engine and remove the key.

2. Ensure that the auger has stopped rotating.

3. Use a clean-out tool to remove snow from the discharge

chute. Never clear a clogged discharge chute with your

hands!

Using the Headlight

Some models are equipped with a headlight to help illuminate

the area in front of the snowthrower. The headlight is on

whenever the engine is running. There is no switch.

Maintenance and Adjustments

We recommend contacting an authorized service dealer for all

maintenance, adjustments, and servicing of the unit. Some

routine maintenance tasks can be performed by the owner.

Refer to the maintenance schedule and procedures that follow.

CAUTION

All the components used to build this product must remain in

place for proper operation. Replacement parts must be of the

same design and installed in the same position as the orginial

parts. Other parts may not perform as well, may damage the

unit, and may result in injury.

WARNING

This snowthrower must be properly maintained to ensure safe

operation and performance. Failure to observe the safety

instructions in this manual could result in death or serious

injury.

• Before performing any maintenance or repairs on the

snowthrower, shut OFF the engine and remove the ignition

key or the Push/Pull key.

Maintenance Schedule

First 5 Hours

Change oil

Before Each Use

• Check engine oil level

• Check auger stop time

After Each Use

Remove accumulated snow and slush to prevent freezing of the controls,

wheels, discharge chute, and auger

Every 25 Hours or Annually

• Check scraper bar and rubber auger for wear

• Change engine oil

• Check snowthrower for loose hardware

• Check auger control cable adjustment

• Check condition of muffler and muffler guard

• Replace sparkplug (dealer service)

• Check valve clearance* (dealer service)

* Not required unless problems are noted with engine performance.

Emissions Control

Maintenance, replacement, or repair of the emissions control

devices and systems may be performed by any non-road engine

repair establishment or individual. However, to obtain “no

charge” emissions control service, the work must be performed

by a factory authorized dealer.

Changing the Engine Oil

Used oil must be disposed of properly. Do not discard with

household waste. Check with your local authorities, service

center, or dealer for safe disposal or recycling facilities.

Use Briggs & Stratton Synthetic 5W-30 Warranty Certified oil

for best performance. Other high-quality detergent oils are

acceptable if classified for service SG, SH, SJ or higher. Do not

use any additives.

1. With the engine stopped but still warm, turn the ignition key

to the OFF position and remove it or pull out the Push/Pull

key (if equipped).

WARNING

Fuel and its vapors are extremely flammable, which could

cause burns or fire resulting in death or serious injury.

Not for

Reproduction

• When performing maintenance that requires the unit to

be tipped, the fuel tank must be empty or fuel can leak

out and result in a fire or explosion.

2. Remove the oil drain plug (D, Figure 9) and tilt the

snowthrower slightly to drain the oil into an appropriate

container.

3. After the oil has drained, install and tighten the oil drain plug

(D).

4. Place the unit on a level surface.

5. Clean the oil fill area of any moisture or debris.

6. Remove the dipstick (A, Figure 10) and wipe it with a clean

cloth. Set it aside.

7. To add oil, pour slowly into the engine oil fill tube (B). See

Specifications for the oil capacity. Do not overfill.

8. Wait one minute before checking the oil level.

9. Insert and tighten the dipstick, then remove it again to check

the oil level. It should be at the top of the full indicator (C).

10. When the oil level is at the top of the full indicator, install

and tighten the dipstick.

Adjusting the Auger Control Cable

DANGER

The discharge chute contains a rotating auger to throw snow.

Fingers or feet can quickly become caught in the auger

resulting in traumatic amputation or severe laceration.

• Over-tightening the auger cable may cause the auger to

rotate even if the auger control lever is not pressed down.

The auger should rotate only when the auger control is engaged

and must stop within 5 seconds when the auger control is

released. If the auger does not rotate or does not stop as

described, adjust the control cable or contact an authorized

service dealer to adjust the control cable.

1. Shut OFF the engine and remove the ignition key or the

Push/Pull key.

2. Lift the cable cover (A, Figure 11) to expose the adjustment

loops (B) and the cable end fitting (C).

3. Remove the end fitting from the adjustment loop and

reinstall as follows:

Not for

Reproduction

• If the auger rotates while the auger control is not

engaged, lengthen the control cable by installing the

end fitting in the next lowest loop (decrease belt

tension).

• If the auger does not rotate when the auger control is

engaged, shorten the control cable by installing the end

fitting in the next highest loop (increase belt tension).

Note:

Some slack must remain in the cable when the auger

control is not engaged.

4. Lower the cable cover into place.

5. Check the operation of the auger control using the test

below. If the unit does not operate as described, DO NOT

use it. Contact an authorized service dealer to have the unit

inspected and adjusted or repaired.

Testing the Auger Control

With the engine running:

• Press down and hold the auger control lever. The auger

should rotate.

• Release the auger control lever. The auger must stop

within 5 seconds.

Maintaining the Auger and Scraper Bar

1. Shut OFF the engine and remove the ignition key or the

Push/Pull key.

2. Check the wear limit on the rubber auger (A, Figure 12) and

the gap between the scraper bar support and the ground

(B).

• If the wear limit on the rubber auger is reached, the two

rubber flights need replacing. Contact an authorized dealer.

• If the scraper bar support makes contact with the ground,

the scraper bar needs replacing. Contact an authorized

dealer.

Storage

At the end of the season, or whenever the unit will be stored for

30 days or more, follow the storage checklist below.

WARNING

Gasoline is highly flammable and its vapors are explosive.

Fumes may travel to a distant ignition source and an explosion

and/or fire could result.

• If there is fuel in the tank, do not store the unit indoors or

in a poorly ventilated area where fumes could reach

sparks, open flames, pilot lights, heat, and other ignition

sources.

Not for

Reproduction

Engine:

Fuel can become stale when stored more than 30 days. Stale

fuel can cause acid and gum deposits to form in the fuel system

and the carburetor. To keep fuel fresh, add Briggs & Stratton

Advanced Formula Fuel Treatment & Stabilizer.

• There is no need to drain the fuel from the engine if a

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system. If no stabilizer is added, the fuel must be drained

from the engine into an approved container. Then run the

engine until it stops from lack of fuel.

• While the engine is still warm, change the oil. See Changing

the Engine Oil.

Snowthrower:

• Ensure all nuts, bolts, and screws are securely fastened.

• Inspect all external moving parts for damage and wear.

Replace parts as necessary.

• For unpainted or bare metal surfaces, apply a rust

preventative product.

• Store the unit indoors and cover it.

• If the unit must be stored outdoors, cover it with a heavy

tarpaulin.

Returning the Unit to Service:

• Have an authorized service dealer perform annual

maintenance tasks. See Maintenance Schedule.

• Check the engine oil level and add oil if necessary.

• Remove any debris around the muffler and cylinder areas.

• Fill the fuel tank with fresh, clean fuel.

• Ensure all guards, shields, and covers are in place.

• Test the auger control.

Not for

Reproduction

Troubleshooting

SolutionCauseProblem

See

Adjusting the Auger Control Cable

.Control cable requires adjustmentAuger does not stop when auger control is

released

See

Adjusting the Auger Control Cable

.Control cable requires adjustmentAuger does not turn when auger control is

engaged

Turn key to the ON position.Key is offEngine does not start

Press primer button twice before pulling starter rope.Primer not pressed

Fill fuel tank with fresh fuel.Out of fuel

Turn choke to closed position before pulling starter

rope.

Choke open - cold engine

Turn choke to open position; pull starter rope several

times until engine starts.

Engine flooded

Fill fuel tank with fresh fuel.Water in fuel or old fuel

Plug in cord or replace defective cord; reset circuit

breaker.

Cord not plugged in or circuit breaker tripped (electric

start models)

Clear snow or ice from chute and deflector parts;

place snowthrower in a heated area until snow or ice

melts.

Chute or deflector is frozenChute rotation or deflector adjustment does not

work

Change oil to lighter viscosity (such as 5W-30).Incorrect oilEngine is hard to start or runs poorly

Open choke control gradually as engine warms up.Choke control set incorrectly

Stop snowthrower immediately. Contact an

Authorized Service Dealer.

Loose parts or damaged partsExcessive vibration

See

Maintaining the Auger and Scraper Bar

.Scraper bar or auger flight wornScraper bar does not clean hard surface

See

Adjusting the Auger Control Cable

.Control cable requires adjustmentSnowthrower does not discharge snow

STOP THE ENGINE! Ensure that the auger has

stopped rotating. Use a clean-out tool to remove

snow from the discharge chute. Never clear a clogged

discharge chute with your hands! See

Clearing a

Clogged Discharge Chute

Discharge chute clogged with snow

See

Maintaining the Auger and Scraper Bar

.Rubber auger is worn or damagedSnowthrower does not self-propel

For all other issues, please see an authorized dealer.

Not for

Reproduction

Specifications

The spark ignition system on this snowthrower complies with Canadian standard ICES-002.

Snow Series 150000Snow Series 130000Snow Series 120000Snow Series 100000Engine Model

20 oz (,59 L)20 oz (,59 L)20 oz (,59 L)20 oz ( ,59 L)Oil Capacity

3.2 qts (3,0 L)3.2 qts (3,0 L)3.2 qts (3,0 L)3.0 qts (2,8 L)Fuel Tank Capacity

.030 in (,76 mm).030 in (,76 mm).030 in (,76 mm).030 in (,76 mm)Sparkplug Gap

180 lb-in (20 Nm)180 lb-in (20 Nm)180 lb-in (20 Nm)180 lb-in (20 Nm)Sparkplug Torque

.010 - .014 in (,25 - ,36 mm).010 - .014 in (,25 - ,36 mm).010 - .014 in (,25 - ,36 mm).010 - .014 in (,25 - ,36 mm)Armature Air Gap

.004 - .006 in (,10 - ,15 mm).004 - .006 in (,10 - ,15 mm).004 - .006 in (,10 - ,15 mm).004 - .006 in (,10 - ,15 mm)Intake Valve Clearance

.009 - .011 in (,23 - ,28 mm).006 - .008 in (,15 - ,20 mm).009 - .011 in (,23 - ,28 mm).006 - .008 in (,15 - ,20 mm)Exhaust Valve Clearance

* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above see level and 1% for each 10° F (5.6° C) above 77° F (25° C). The engine will

operate satisfactorily at an angle up to 15°.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive Engineers)

code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are

derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are

taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments. Actual gross

engine power will be higher than net engine power and is affected by, among other things, ambient operating conditions and

engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine may not develop

the rated gross power when used in a given piece of power equipment. This difference is due to a variety of factors including,

but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application

limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing

and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this engine.

Not for

Reproduction

Índice de contenidos:

Información general............................................................17

Seguridad del operador......................................................17

Características y controles................................................20

Operación.............................................................................21

Mantenimiento y ajustes.....................................................26

Almacenamiento..................................................................29

Detección de fallas..............................................................30

Especificaciones.................................................................31

Información general

Para obtener información adicional, consulte la

Guía de contacto

del cliente

Instrucciones de montaje

incluidas con la unidad.

Las ilustraciones que aparecen en este documento son

representativas. Su unidad puede diferir de las imágenes que

se muestran.

IZQUIERDA

DERECHA

se referencian a partir

de la posición de funcionamiento.

El empleo de las palabras "Importante" y "Nota" en el texto

indica aclaraciones, excepciones o alternativas a los

procedimientos proporcionados.

Todas las traducciones de este documento se derivan del

archivo fuente original en inglés.

Todos los envases, el aceite usado y las baterías deben

reciclarse de acuerdo con las regulaciones gubernamentales

aplicables.

Seguridad del operador

Guarde estas instrucciones para futura referencia. Este

manual contiene información sobre seguridad para hacer que

tome consciencia de los peligros y riesgos asociados con el

producto y cómo evitarlos. También contiene importantes

instrucciones que deben seguirse durante la configuración

inicial, la operación y el mantenimiento del producto.

La máquina quitanieves está diseñada exclusivamente para la

limpieza de nieve de senderos y caminos de acceso de

superficies rígidas y niveladas, y no está destinada para ningún

otro propósito.

Es importante que lea y comprenda estas instrucciones antes

de intentar arrancar u operar este equipo.

Procure estar familiarizado con los controles y el uso adecuado

de la máquina quitanieves.

Aprenda cómo detener la unidad y desactivar los controles

rápidamente.

Símbolo de alerta de seguridad y palabras

de señalización

El símbolo de alerta de seguridad ( ) se usa para identificar

información de seguridad sobre riesgos que pueden provocar

lesiones personales. Se utiliza una palabra de señalización

(PELIGRO, ADVERTENCIA o PRECAUCIÓN) junto con el

símbolo de alerta para indicar la probabilidad de una lesión y

su potencial gravedad. Además, se puede usar un símbolo de

peligro para representar el tipo de riesgo.

PELIGRO indica un riesgo que, de no evitarse, puede

provocar lesiones graves o la muerte.

ADVERTENCIA indica un riesgo que, de no evitarse, podría

provocar lesiones graves o la muerte.

PRECAUCIÓN indica un riesgo que, de no evitarse, podría

ocasionar lesiones moderadas o menores.

AVISO

indica una situación que podría dar como resultado

daños al producto.

Símbolos de peligro de la máquina

quitanieves

SignificadoSímboloSignificadoSímbolo

Lea y comprenda el Manual

del operador antes de

operar o reparar la unidad.

Información de

seguridad sobre peligros

que pueden provocar

lesiones personales.

Quite la llave antes de

realizar el servicio. Lea el

Manual del operador antes

de realizar el servicio.

Peligro de amputación:

impulsor giratorio.

Peligro de amputación:

barrena giratoria.

Peligro de amputación:

impulsor giratorio.

Peligro de objetos

lanzados.

Peligro de amputación:

no toque las piezas

móviles.

Peligro de explosión.Peligro de incendio.

Peligro de vapores tóxicos.Peligro de descarga

eléctrica.

Peligro de retroceso

violento.

Peligro de superficie

caliente.

Mantenga a los niños

alejados.

Mantenga una distancia

segura.

Not for

Reproduction

SignificadoSímboloSignificadoSímbolo

— — —— — —Use gafas de seguridad.

Mensajes de seguridad

PELIGRO

Esta máquina quitanieves es capaz de amputar manos y pies,

y arrojar objetos. Lea y siga todas las instrucciones de

seguridad incluidas en este manual. Omitir esto podría tener

como consecuencia la muerte o lesiones graves.

El contacto manual con la barrena giratoria dentro de la

manga de descarga es la causa más común de lesiones

asociadas con la máquina quitanieves.

ADVERTENCIA

Lea, comprenda y siga todas las instrucciones que se

encuentran en la máquina quitanieves y en el Manual del

operador antes de operar la unidad. El incumplimiento de las

instrucciones de seguridad incluidas en este manual podría

ocasionar la muerte o lesiones graves.

• Solo permita que operadores responsables, capacitados,

familiarizados con las instrucciones y físicamente aptos

operen la máquina.

ADVERTENCIA

Utilice siempre gafas de seguridad o protectores oculares

durante el funcionamiento o mientras realice un ajuste o una

reparación para proteger los ojos de objetos extraños que

puedan ser lanzados de la máquina.

Modelos de EE. UU.: Es una violación del Código de Recursos

Públicos de California, Sección 4442, utilizar u operar el motor

en cualquier espacio con árboles, maleza o grama a menos

que el sistema de escape esté equipado con un extintor de

chispas, como lo define la Sección 4442, mantenido en correcto

funcionamiento. Otros estados o jurisdicciones federales pueden

tener leyes similares. Póngase en contacto con el vendedor, el

distribuidor o el fabricante del equipo original para obtener un

extintor de chispas diseñado para el sistema de escape

instalado en este motor.

ADVERTENCIA

Este producto puede exponerlo a sustancias químicas entre

las que se incluyen emisiones de escape de motor de

gasolina, reconocidas por el Estado de California como

causantes de cáncer; y monóxido de carbono, reconocido

por el Estado de California como causante de defectos de

nacimiento u otros problemas reproductivos. Para obtener

más información, visite www.P65Warnings.ca.gov.

Calcomanías de seguridad

Para evitar lesiones, lea y comprenda las calcomanías de

seguridad en la máquina quitanieves antes de ponerlo en

funcionamiento. Haga coincidir las letras en la Figura 1 para

las calcomanías que figuran en la tabla adjunta.

Si las calcomanías de seguridad se han desgastado, dañado

o están ilegibles, póngase en contacto con un distribuidor

autorizado de servicio para pedir repuestos.

Not for

Reproduction

Not for

Reproduction

Características y controles

Haga corresponder las letras de identificación en la Figura 2 con las características y los controles indicados en la tabla que lo

acompaña.

Símbolos de control y significados

Control de la barrenaA

Barrena— — —B

Control de la manga - Montaje de la palanca (si tiene)C

Rotación de la manga de descarga - Montaje de la

manga (si tiene)

Control de la manga - Montaje del interruptor (si tiene)E

Control del deflector - Disparador o perilla de aletaF

Botón de arranqueG

Receptáculo de arranqueH

Calcomanía con instrucciones de arranque (si tiene)— — —I

Calcomanía con instrucciones de arranque (si tiene)— — —J

Luces delanteras (si tiene)— — —K

Estrangulador cerrado, estrangulador abiertoL

Tapa y tanque de combustible— — —M

Llenado de aceite y varilla indicadora de nivel de aceite— — —N

Botón del cebadorO

Interruptor de encendido y apagadoP

Manija de la cuerda de arranque— — —Q

Tapón de drenaje de aceite— — —R

La page charge ...

Simplicity 1696717-00 Manuel utilisateur

Marque: Simplicity

Modèle: 1696717-00

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

Simplicity 1696717-00 Manuel utilisateur

Ce manuel convient également à

Simplicity 1696717-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents