Indesit IWSE 6108 ECO (EE) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and options, 7
Table of wash cycles
Wash options
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
IWSE 6108
Instructions for use
WASHING MACHINE
English,1
GB
Magyar,13
HU
Èesky,25
CZ
UK
Óêðà¿íñüêà,37
2
GB
Installation
This instruction manual should be kept in a safe
place for future reference. If the washing machine is
sold, transferred or moved, make sure that the
instruction manual remains with the machine so that
the new owner is able to familiarise himself/herself
with its operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washing machine
by screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Technical data
Model
IWSE 6108
Dimensions
width 59.5 cm
height 85 cm
depth 40 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 1000 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme 2; temperature 60°C;
using a load of 6 kg.
This appliance conforms to the
following EC Directives:
- 2004/108/EC (Electromagnetic
Compatibility)
- 2002/96/EC
- 2006/95/EC (Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washing machine. If this is not the case, replace
the socket or the plug.
The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to rain,
storms and other weather conditions.
When the washing machine has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 2.
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
ON/OFF button
: press this briefly to switch the
machine on or off. The START/PAUSE indicator light,
which flashes slowly in a green colour shows that the
machine is switched on. To switch off the washing
machine during the wash cycle, press and hold the
button for approximately 2 seconds; if the button is
pressed briefly or accidentally the machine will not
switch off. If the machine is switched off during a
wash cycle, this wash cycle will be cancelled.
WASH CYCLE knob: used to set the desired wash
cycle (see "Table of wash cycles").
OPTION buttons with indicator light: used to select
the available options. The indicator light corresponding
to the selected option will remain lit.
SPIN button
: press to reduce or completely
exclude the spin cycle - the value is indicated on the
display.
TEMPERATURE button
: press to decrease or
completely exclude the temperature: the value will be
shown on the display.
DELAYED START button
: press to set a delayed
start time for the selected wash cycle. The delay time
will be shown on the display.
START/PAUSE button
with indicator light: when
the green indicator light flashes slowly, press the
button to start a wash cycle. Once the cycle has
begun the indicator light will remain lit in a fixed
manner. To pause the wash cycle, press the button
again; the indicator light will flash in an orange colour.
If the symbol
is not illuminated, the door may be
opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new
energy saving regulations, is fitted with an automatic
standby system which is enabled after about 30
minutes if no activity is detected. Press the ON-OFF
button briefly and wait for the machine to start up
again.
Description of the washing
machine
Control panel
TEMPERATURE
Button
Detergent dispenser drawer
OPTION
buttons with
indicator lights
ON/OFF
button
SPIN SPEED
Button
START/PAUSE
button with indicator light
DISPLAY
DELAYED
START
Button
WASH CYCLE
knob
GB
5
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available programmes and the remaining time of a running cycle appear in section A; if the
DELAY START option has been set, the countdown to the start of the selected programme will appear. Pressing
the relative button, the machine automatically displays the maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings if they are compatible with the selected cycle.
The "programme phases" relative to the selected programme and the "programme phase" of the running
programme appear in section B:
Wash
Rinse
Spin
Drain
The icons corresponding to "temperature"
, "Programmed start" and "spin" appear in section C from top
to bottom:
If the
symbol lights up, the display will visualise the set "temperature" value.
When a delayed start has been set, the
symbol lights up.
If the
symbol lights up, the display will visualise the set "spin" value.
Door locked symbol
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before
opening the door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED
symbol is
switched off the door may be opened.
B
C
A
6
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the
button; the START/PAUSE indicator light will flash
slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
"Detergents and laundry".
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Set the WASH
CYCLE knob to the desired programme; a
temperature and spin speed is set for each wash
cycle; these may be adjusted. The duration of the
cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the
relevant buttons:
Modifying the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set
for the selected cycle, or the most recently-used
settings if they are compatible with the selected
cycle. The temperature can be decreased by
pressing the
button, until the cold wash "OFF"
setting is reached. The spin speed may be
progressively reduced by pressing the
button,
until it is completely excluded (the "OFF" setting). If
these buttons are pressed again, the maximum
values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the
symbol lights up on the
display. To remove the delayed start option press
the button until the text "OFF" appears on the
display.
Modifying the cycle
settings.
Press the button to enable the option; the
indicator light corresponding to the button will
switch on.
Press the button again to disable the option; the
indicator light will switch off.
If the selected option is not compatible with the
programmed wash cycle, the indicator light will
flash and the option will not be activated.
If the selected option is not compatible with
another option which has been selected previously,
the indicator light corresponding to the first option
selected will flash and only the second option will be
activated; the indicator light corresponding to the
enabled option will remain lit.
The options may affect the recommended load
value and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and
the door will be locked (the DOOR LOCKED
symbol
will be on). To change a wash cycle while
it is in progress, pause the washing machine using
the START/PAUSE button (the START/PAUSE
indicator light will flash slowly in an orange colour);
then select the desired cycle and press the START/
PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened.
Press the START/PAUSE button again to restart the
wash cycle from the point at which it was
interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text "END" on the display; when
the DOOR LOCKED
symbol switches off the door
may be opened. Open the door, unload the laundry
and switch off the machine.
If you wish to cancel a cycle which has already
begun, press and hold the button. The cycle will be
stopped and the machine will switch off.
GB
7
Wash cycles and options
Description of the wash cycle
Max
.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Cycle
duration
Prewash Wash
Fabric
softener
Normal
Eco
Time
Daily
1
Cotton with prewash:
extremely soiled whites.
90° 1000
lll
6
-
2
Cotton:
extremely soiled whites.
90° 1000
-
ll
6
-
2
Cotton (1):
heavily soiled whites and resistant colours.
60° 1000
-
ll
6
-
2
Cotton (2):
heavily soiled whites and delicate colours.
40° 1000
-
ll
6
-
3
Cotton:
heavily soiled whites and resistant colours.
60° 1000
-
ll
62,5
4
Coloured Cottons (3):
lightly soiled whites and delicate colours.
40° 1000
-
ll
62,5
5
Synthetics:
heavily soiled resistant colours.
60° 800
-
ll
2,5 1,5
6
Synthetics:
lightly soiled resistant colours.
40° 800
-
ll
2,5 1,5
Special
7
Wool:
for wool, cashmere, etc.
40° 600
-
ll
1
-
8
Silk/Curtains:
for garments in silk and viscose, lingerie.
30° 0
-
ll
1
-
9
Jeans
40° 800
-
ll
2,5
-
10
Express:
to refresh lightly soiled garments quickly (not suitable for wool, silk
and clothes which require washing by hand).
30° 800
-
ll
1,5
-
Sport
11
Sport Intensive
30° 600
-
ll
2,5
-
12
Sport Light
30° 600
-
ll
2,5
-
13
Sport Shoes
30° 600
-
ll
Max. 2
pairs
-
Partial wash cycles
Rinse
-
1000
- -
l
6
-
Spin
-
1000
- - -
6
-
Drain
-
0
- - -
6
-
Wash options
Selecting this option enables you to suitably adjust
drum rotation, temperature and water to a reduced
load of lightly soiled cotton and synthetic fabrics (refer
to the "Table of wash cycles").
enables you
to wash in less time thereby saving water and
electricity. We suggest using a liquid detergent
suitably measured out to the load quantity.
It cannot be used with the 1, 2, 7, 8, 9, 10, 11, 12,
13,
, , programmes.
The function saves energy by not heating the
water used to wash your laundry - an advantage both
to the environment and to your energy bill. Instead,
intensified wash action and water optimisation ensure
great wash results in the same average time of a
standard cycle.
For the best washing results we recommend the usage
of a liquid detergent.
It cannot be used with the 1, 7, 8, 10, 11, 12, 13,
, , programmes.
Table of wash cycles
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is
guaranteed. It is particularly useful for sensitive skin.
It cannot be used in conjunction with the 10, ,
programmes.
Easy iron
By selecting this function, the wash and spin cycles
will be modified in order to reduce the formation of
creases. At the end of the cycle the washing machine
will perform slow rotations of the drum; the indicator
lights for the EASY IRON and START/PAUSE options
will flash (the first one green, the second orange).
To end the cycle, press the START/PAUSE button or
the EASY IRON button.
For the 8 wash cycles, the machine will end the cycle
while the laundry is soaking and the EASY IRON and
START/PAUSE indicator lights will flash. To drain the
water so that the laundry may be removed, press the
START/PAUSE button or the EASY IRON button.
This function may not be used in conjunction with
wash cycles 7, 10, 11, 12, 13,
, .
The duration of the wash cycles can be checked
on the display.
Wash
cycles
The information contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 6 kg
Synthetic fabrics: max. 2,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 1 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Wool: all wool garments can be washed using
programme 7, even those carrying the "hand-wash
only"
label. For best results, use special
detergents and do not exceed 1 kg of laundry.
Silk: use special wash cycle 8 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 8.
Jeans: Turn garments inside-out before washing and
use a liquid detergent. Use programme 9.
Express: this wash cycle was designed to wash
lightly soiled garments quickly: it lasts just 15 minutes
and therefore saves both energy and time. By
selecting this wash cycle (
10
at 30°C), it is possible to
wash different fabrics together (except for wool and
silk items), with a maximum load of 1,5 kg.
Sport Intensive (
wash cycle
11): is for washing
heavily soiled sports clothing fabrics (tracksuits,
shorts, etc.); for best results, we recommend not
exceeding the maximum load indicated in the "Table
of wash cycles".
Sport Light (
wash cycle
12): is for washing lightly
soiled sports clothing fabrics (tracksuits, shorts, etc.);
for best results, we recommend not exceeding the
maximum load indicated in the "Table of wash
cycles". We recommend using a liquid detergent and
dosage suitable for a half-load.
Sport Shoes (
wash cycle
13): is for washing sports
shoes; for best results, do not wash more than 2 pairs
simultaneously.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washing machine
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.
1
2
3
GB
9
Precautions and tips
This washing machine was designed and
constructed in accordance with international safety
regulations. The following information is provided for
safety reasons and must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
Do not open the detergent dispenser drawer while
the machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
Opening the porthole door manually
In the event that it is not possible to open the
porthole door due to a powercut, and if you wish to
remove the laundry, proceed as follows:
1. remove the plug from
the electrical socket.
2. make sure the water
level inside the machine is
lower than the door
opening; if it is not, remove
excess water using the
drain hose, collecting it in a
bucket as indicated in the
figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see
figure).
4. pull outwards using the tab as indicated in the
figure, until the plastic tie-rod is freed from its stop
position; pull downwards and open the door at the
same time.
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
20
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and
during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine
(see figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use second-hand hoses.
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),
make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water ("H2O" will flash
on the display).
The washing machine
continuously takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The "option" indicator lights and the
"start/pause" indicator light flash
and an error code appears on the
display (e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see Running a wash cycle).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the
dwelling is on one of the upper floors of a building, there may be problems
relating to water drainage, causing the washing machine to fill with water
and drain continuously. Special anti-draining valves are available in shops
and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the
drain phase to be started manually.
The Easy iron option has been activated: To complete the wash cycle,
press the START/PAUSE button (see Wash cycles and options).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see Care
and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the
text for washing machines or hand and machine wash, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also
be found on the front of the appliance by opening the door.
HU
!
Magyar
Összefoglalás
Üzembe helyezés, 1415
Kicsomagolás és vízszintbe állítás
Víz- és elektromos csatlakozás
Elsõ mosási ciklus
Mûszaki adatok
A mosógép leírása, 16-17
Kezelõpanel
Kijelzõ
A mosási ciklusok végrehajtása, 18
Programok és funkciók, 19
Programtáblázat
Mosási funkciók
Mosószerek és mosandók, 20
Mosószer-adagoló fiók
A mosandó ruhák elõkészítése
Különleges programok
A bepakolt ruhák kiegyensúlyozására szolgáló
rendszer
Óvintézkedések és tanácsok, 21
Általános biztonság
Hulladékelhelyezés
Az ajtó kézi nyitása
Karbantartás és ápolás, 22
A víz elzárása és az elektromos áram kikapcsolása
A mosógép tisztítása
A mosószer-adagoló fiók tisztítása
Az ajtó és a forgódob ápolása
A szivattyú tisztítása
A vízbevezetõ csõ ellenõrzése
Rendellenességek és elhárításuk, 23
Szerviz, 24
HU
IWSE 6108
Használati utasítás
MOSÓGÉP
"
HU
Üzembe helyezés
Fontos, hogy megõrizze ezt a kézikönyvet, hogy
mindig kéznél legyen. Ha a mosógépet eladná,
átadná vagy másnál helyezné el, gondoskodjon
arról, hogy e kézikönyv a mosógéppel együtt
maradjon, hogy az új tulajdonos is megismerhesse
a készülék funkcióit és az ezekre vonatkozó
figyelmeztetéseket.
Figyelmesen olvassa el az utasításokat: fontos
információkat tartalmaznak az üzembe helyezésrõl,
a használatról és a biztonságról.
Kicsomagolás és vízszintbe állítás
Kicsomagolás
1. Csomagolja ki a mosógépet.
2. Ellenõrizze, hogy a mosógép nem sérült-e meg a
szállítás során. Ha a gépen sérülést talál, ne
csatlakoztassa, és forduljon a viszonteladóhoz.
3. Csavarozza ki a gép
hátsó részén található, a
szállításhoz szükséges
4 védõcsavart, és
távolítsa el a gumibakot
(lásd ábra).
4. Zárja le a furatokat a mellékelt mûanyag
dugókkal.
5. Minden darabot õrizzen meg: ha a mosógépet
szállítani kell, elõtte ezeket vissza kell szerelni.
A csomagolóanyag nem gyermekjáték!
Vízszintbe állítás
1. A mosógépet sík és kemény padlóra állítsa, úgy,
hogy ne érjen falhoz, bútorhoz vagy máshoz.
2. Ha a padló nem
tökéletesen vízszintes,
azt az elsõ lábak be-,
illetve kicsavarásával
kompenzálhatja (lásd
ábra). A gép felsõ
burkolatán mért dõlés
nem haladhatja meg a
2°-ot.
A pontos vízszintezés biztosítja a gép stabilitását,
így az a mûködés során nem fog rezegni, zajt
okozni, illetve elmozdulni. Szõnyegpadló vagy
szõnyeg esetén a lábakat úgy állítsa be, hogy a
mosógép alatt elegendõ hely maradjon a
szellõzésre.
Víz- és elektromos csatlakozás
Vízbevezetõ csõ csatlakoztatása
1. A vízbevezetõ csõ
csatlakoztatásához
csavarozza fel a csövet
egy 3/4-os külsõ
menettel rendelkezõ
hidegvíz csapra (lásd
ábra).
A csatlakoztatás elõtt
eressze meg a csapot
addig, amíg a víz teljesen
átlátszóvá nem válik.
2. A vízbevezetõ csõ
csatlakoztatásához
csavarozza a csövet a
mosógép hátoldalán
jobbra fent található
vízbemeneti csonkra
(lásd ábra)!
3. Ügyeljen arra, hogy a csövön ne legyen törés
vagy szûkület!
A csap víznyomásának a mûszaki adatok
táblázatában szereplõ határértékek között kell
lennie (lásd a szemben lévõ oldalt).
Amennyiben a vízbevezetõ csõ nem elég hosszú,
forduljon szaküzlethez vagy engedéllyel rendelkezõ
szakemberhez.
Soha ne használjon korábban már használt
csöveket.
Használja a készülékhez mellékelteket.
HU
#
Mûszaki adatok
Modell
IWSE 6108
Méretek
szélesség 59,5 cm
magasság 85 cm
mélység 40 cm
Ruhatöltet:
1-tõl 6 kg-ig
Elektromos
csatlakozás
lásd a készüléken található, muszaki
jellemzoket tartalma adattábt!
Vízcsatlakozások
maximális nyos 1 MPa (10 bar)
minimális nyomás 0,05 MPa (0,5 bar)
dob ûrtartalma 40 liter
Centrifuga
fordulatszám
1000 fordulat/perc-ig
EN 60456 szabvány
Szerinti
vezérlõprogramok
2-as program; hõmérséklet 60
°
C;
6 kg ruhatöltettel végezve.
Ez a berendezés megfelel a következõ
Uniós Elõírásoknak:
- 2004/108/CE (Elektromágneses
összeférhetõség)
- 2002/96/CE
- 2006/95/CE (Alacsony feszültség)
65 - 100 cm
A leeresztõcsõ csatlakoztatása
Csatlakoztassa a
leeresztõcsövet a
lefolyóhoz vagy a
padlótól 65 és 100cm
közötti magasságban
lévõ fali szifonhoz
anélkül, hogy megtörné;
illetve akassza a mosdó
vagy a kád szélére úgy,
hogy a mellékelt
csõvezetõ ívet a csaphoz
erõsíti (lásd ábra). A
leeresztõcsõ szabad
végének nem szabad
vízbe merülnie.
Toldások használata nem javasolt. Amennyiben
feltétlenül szükséges, a toldás átmérõje egyezzen
meg az eredeti csõével és semmiképpen se legyen
150cm-nél hosszabb.
Elektromos csatlakoztatás
Mielõtt a csatlakozódugót az aljzatba dugná,
bizonyosodjon meg arról, hogy:
az aljzat földelése megfelel a törvény által
elõírtnak;
az aljzat képes elviselni a készülék mûszaki
adatait tartalmazó táblázatban megadott maximális
teljesítményfelvételt (lásd szemben);
a hálózat feszültsége a mûszaki adatokat
tartalmazó táblázatban szereplõ értékek közé esik
(lásd szemben);
az aljzat kompatibilis a mosógép
csatlakozódugójával. Ellenkezõ esetben cserélje ki
az aljzatot vagy a csatlakozódugót!
A mosógép nem állítható fel nyílt téren, még akkor
sem, ha tetõ van fölötte, mivel nagyon veszélyes, ha
a gép esõnek vagy zivataroknak van kitéve.
A csatlakozódugónak a mosógép üzembe helyezett
állapotában is könnyen elérhetõ helyen kell lennie.
Ne használjon hosszabbítót vagy elosztót.
A kábel ne legyen se megtörve, se összenyomva.
A tápkábelt csak engedéllyel rendelkezõ
szakember cserélheti.
Figyelem! A fenti elõírások figyelmen kívül hagyása
esetén a gyártó elhárít minden felelõsséget.
Elsõ mosási ciklus
Üzembe helyezés után mielõtt a mosógépet
használni kezdené mosószerrel, mosandó ruha
nélkül futtassa le az 2-es mosási programot.
$
HU
Mosószer-adagoló fiók: a mosószerek és
adalékanyagok betöltésére szolgál (lásd
Mosószerek és mosandók).
BEKAPCSOLÁS/KIKAPCSOLÁS gomb
: a
készülék be-, vagy kikapcsolásához nyomja meg
röviden ezt a gombot. Amennyiben az ELINDÍTÁS/
SZÜNETELTETÉS lámpa zöld fénnyel lassan villog,
a készülék be van kapcsolva. A mosógép mosás
közben történõ leállításához hosszan, kb. 2
másodpercig tartsa lenyomva a nyomógombot a
gomb rövid, vagy véletlen megnyomása nem
kapcsolja le a készüléket. A mosógép mosás
közben történõ leállítása magát a mosás programot
is törli. A kívánt programot újból be kell állítani.
PROGRAMOK tekerõgomb: a kívánt program
beállítására szolgálnak (lásd Programtáblázat).
FUNKCIÓ jelzõlámpás gombok: a lehetséges
funkciók kiválasztására szolgál. A kiválasztott
funkció jelzõlámpája égve marad.
CENTRIFUGÁLÁS
gomb: a centrifugálás
sebességének csökkentéséhez, vagy annak teljes
kikapcsolásához nyomja meg ezt a gombot az
érték megjelenik a kijelzõn.
HÕMÉRSÉKLET
gomb: a homérséklet
csökkentéséhez vagy mellozéséhez nyomja meg
ezt a gombot - az érték megjelenik a kijelzon.
KÉSLELTETETT INDÍTÁS
gomb: a kiválasztott
program késleltetett elindításához nyomja meg ezt a
gombot. A késleltetés értéke megjelenik a kijelzõn.
ELINDÍTÁS/SZÜNETELTETÉS
jelzolámpás
gomb: ha a zöld jelzõlámpa lassan villog, a mosás
indításához nyomja meg ezt a gombot. A ciklus
elindításával a jelzõlámpa állandó fénnyel kezd
világítani. A mosás szüneteltetéséhez ismételten
nyomja meg ezt a gombot; a jelzõlámpa
narancssárga fénnyel kezd el villogni. Amennyiben a
szimbólum nem világít, az ajtót ki lehet nyitni. A
mosásnak a megszakítás idõpontjától való
folytatásához nyomja meg ismét ezt a gombot.
Készenléti üzemmód
Ez a mosógép - az energiatakarékosságra
vonatkozó legújabb eloírásoknak megfeleloen -
automatikus kikapcsolási (készenléti) rendszerrel
van ellátva, mely a használat megadott 30 percnyi
szüneteltetése esetén bekapcsol. Nyomja meg
röviden a BE/KI gombot, és várjon, amíg a készülék
újrabekapcsol.
A mosógép leírása
ELINDÍTÁS/
SZÜNETELTETÉS
jelzõlámpás gomb
Kezelõpanel
HÕMÉRSÉKLET
gomb
CENTRIFUGÁLÁS
gomb
PROGRAMOK
tekerõgomb
BEKAPCSOLÁS/
KIKAPCSOLÁS
gomb
Mosószer-adagoló fiók
FUNKCIÓ
jelzõlámpás gombok
Kijelzõ
KÉSLELTETETT
INDÍTÁS
gomb
HU
%
Kijelzõ
A kijelzõ a készülék programozásához nyújt segítséget, és számos információt szolgáltat.
Az A feliratmezõben a rendelkezésre álló programok hossza, illetve elindított ciklus esetén a program végéig
hátralévõ maradékidõ látható. KÉSLELTETETT INDÍTÁS beállítása esetén a kiválasztott program elindulásáig
hátralévõ idõt jeleníti meg. Ezenkívül a vonatkozó gomb, a készülék automatikusan kijelzi az elindított
programhoz tartozó legmagasabb homérsékletet és centrifugasebességet, vagy a legutóbb kiválasztottakat,
amennyiben azok kompatíbilisek a kiválasztott programmal.
A B feliratmezõ a kiválasztott mosási program mosási fázisait, elindított program esetén pedig az éppen
folyamatban lévõ mosási fázist jeleníti meg.
Mosás
Öblítés
Centrifugálás
Szivattyûzás
A C feliratmezoben föntrol lefelé a "homérséklet"
, a "KÉSLELTETETT INDÍTÁS" és a "centrifugálás"
szimbólumai jelennek meg:
A világító
szimbólum azt jelzi, hogy a kijelzo a beállított homérsékletet mutatja.
A világító
szimbólum azt jelzi, hogy késleltetett indítás van beállítva.
A világító
szimbólum azt jelzi, hogy a kijelzo a beállított centrifugasebességet mutatja.
Ajtózár szimbólum
A világító szimbólum azt jelöli, hogy az ajtó reteszelve van. A károk elkerülése érdekében az ajtó kinyitása
elott meg kell várni, hogy a szimbólum kialudjon.
Az ajtó menet közbeni kinyitásához nyomja meg az ELINDÍTÁS/SZÜNETELTETÉS gombot ha az
AJTÓZÁR
szimbólum kialudt, kinyithatja az ajtót.
B
C
A
&
HU
A mosási ciklusok végrehajtása
1. A KÉSZÜLÉK BEKAPCSOLÁSA. Nyomja meg a
gombot, az ELINDÍTÁS/SZÜNETELTETÉS
lámpa pedig lassan, zöld fénnyel villogni kezd.
2. A MOSANDÓ RUHÁK BEPAKOLÁSA. Nyissa ki
az ajtót! Tegye be a mosandó ruhákat, ügyelve
arra, hogy ne lépje túl a következõ oldalon
található programtáblázatban feltüntetett
ruhatöltet-mennyiséget.
3. A MOSÓSZER ADAGOLÁSA. Vegye ki a fiókot,
és a Mosószerek és mosandók fejezetben
leírtak szerint öntse a mosószert a megfelelõ
tégelybe.
4. CSUKJA BE AZ AJTÓT.
5. A PROGRAM KIVÁLASZTÁSA. A PROGRAMOK
tekerõgombbal állítsa be a kívánt programot.
Mindegyik programhoz tartozik egy hõmérséklet és
egy centrifugasebesség, melyek megváltoztatható
értékek. A kijelzõn megjelenik a ciklusidõ.
6. A MOSÁSI CIKLUS EGYÉNI BEÁLLÍTÁSAI.
Használja a megfelelõ gombokat:
A hõmérséklet és/vagy a
centrifugasebesség megváltoztatása. A
készülék automatikusan kijelzi az elindított
programhoz tartozó legmagasabb homérsékletet
és centrifugasebességet, vagy a legutóbb
kiválasztottakat, amennyiben azok kompatíbilisek
a kiválasztott programmal. Ezen értékek további
növelése nem lehetséges. A
gomb
nyomogatásával a hõmérséklet fokozatosan
csökkenthetõ egészen a hidegmosásig OFF. A
gomb nyomogatásával a centrifugasebesség
fokozatosan csökkenthetõ egészen annak
kikapcsolásáig OFF. A gomb legalsó értéken
történõ megnyomásával visszatérhet a maximális
értékekhez.
Késleltetett indítás beállítása.
A kiválasztott program késleltetett indításához
nyomogassa a megfelelõ gombot addig, míg a
késleltetés kívánt értékét el nem éri. Ha a funkció
be van kapcsolva, a kijelzõn világít a
szimbólum. A késleltetett indítás törléséhez
nyomogassa a gombot mindaddig, míg a kijelzõn
meg nem jelenik az OFF felirat.
A program
tulajdonságainak módosítása.
A funkció bekapcsolásához nyomja meg ezt a
gombot a gombon található jelzõlámpa világít.
A funkció kikapcsolásához ismételten nyomja
meg a gombot a lámpa kialszik.
! Ha a kiválasztott funkció a beállított programmal
nem kompatibilis, a jelzõlámpa villogni kezd, és a
funkció nem lesz bekapcsolva.
! Ha a kiválasztott funkció egy korábban beállított
programmal nem kompatibilis, az elsõként
kiválasztott funkció lámpája villogni kezd, és csak
a második funkció lesz bekapcsolva, a bekapcsolt
funkció lámpája folyamatosan világít.
! A funkciók megváltoztathatják az ajánlott
ruhatöltet-mennyiséget és/vagy a ciklusidõt.
7. A PROGRAM INDÍTÁSA. Nyomja meg az
ELINDÍTÁS/SZÜNETELTETÉS gombot. A
megfelelõ jelzõlámpa állandó zöld fénnyel
világítani kezd, és az ajtózár bekapcsol (az
AJTÓZÁR szimbólum világítani kezd). A program
menet közben történõ megváltoztatásához az
ELINDÍTÁS/SZÜNETELTETÉS gomb
megnyomásával szüneteltesse le a készülék
mûködését az ELINDÍTÁS/SZÜNETELTETÉS
lámpa narancssárga fénnyel lassan villogni kezd.
Ezután válassza ki a kívánt programot, és nyomja
meg újból az ELINDÍTÁS/SZÜNETELTETÉS
gombot.
Az ajtó menet közbeni kinyitásához nyomja meg
az ELINDÍTÁS/SZÜNETELTETÉS gombot ha az
AJTÓZÁR szimbólum kialudt, kinyithatja az
ajtót. A mosásnak a megszakítás idõpontjától
való folytatásához nyomja meg ismét az
ELINDÍTÁS/SZÜNETELTETÉS gombot.
8. A PROGRAM VÉGE. Ezt a kijelzõn megjelenõ
END felirat jelzi. Ha az AJTÓZÁR
szimbólum
kialszik, ki lehet nyitni az ajtót. Nyissa ki az
ajtót, szedje ki a mosott ruhákat, és kapcsolja ki
a készüléket.
Amennyiben nullázni szeretne egy már elindított
programot, tartsa hosszan lenyomva a
gombot. A
program megszakad, és a készülék kikapcsol.
HU
'
Programlrás
Max.
hom.-
(°C )
Max.
sebesség
(ford./perc)
Mosószerek
Max.
ruhamennyig
(kg)
Progra-
mido
Elo m-
osás
Mosás Öblíto Norl
Eco
Time
Hétköznapi programok
PAMUT ELO MOSÁS:
Erosen szennyezett fehér ruhák.
90° 1000
lll
6
-
PAMUT:
Erosen szennyezett fehér ruhák.
90° 1000
-
ll
6
-
PAMUT (1):
Erosen szennyezett fehér és magasabb ho mérsékleten
mosható színes ruhák.
60° 1000
-
ll
6
-
PAMUT (2):
Erosen szennyezett kényes fehér és színes ruhák.
40° 1000
-
ll
6
-
!
PAMUT:
Erosen szennyezett fehér és magasabb homérkleten
mosható színes ruhák.
60° 1000
-
ll
62,5
"
SZÍNES PAMUT (3):
Enyhén szennyezett fehér és kényes színes ruhák.
40° 1000
-
ll
62,5
#
SZINTETIKUS:
Erosen szennyezett, magasabb ho mérsékleten
mosható színes ruhák.
60° 800
-
ll
61,5
$
SZINTETIKUS:
Enyhén szennyezett, magasabb homérkleten
mosható színes ruhák.
40° 800
-
ll
2,5 1,5
Speciális programok
%
GYAPJÚ:
Gyapjú, kasmír stb. ruhanemuk mosásához.
40° 600
-
ll
1
-
&
SELYEM/FÜGGÖNY:
Selyem ruhanemukhöz, viszkózus anyagokhoz,
fernem ukhöz.
30° 0
-
ll
1
-
'
JEANS
40° 800
-
ll
2,5
-

EXPRESS:
Az enyhén szennyezett ruhadarabok gyors átöblítésére
(nem javasolt gyapjú, selyem és kézzel mosandó ruhanemukhöz).
30° 800
-
ll
1,5
-
Sport
 Sport Intensive
30° 600
-
ll
2,5
-
Sport Light
30° 600
-
ll
2,5
-
!
Sport Shoes
30° 600
-
ll
Max. 2
par
-
Részleges programok
ÖBLÍTÉS
-
1000
- -
l
6
-
CENTRIFUGÁLÁS
-
1000
- - -
6
-
SZIVATTYÚZÁS
-
0
- - -
6
-
Programok és funkciók
Programtáblázat
Programok
A mosási programok mosási ideje leolvasható a kijelzõrõl.
Mosási funkciók
Ennek az opciónak a kiválasztásakor a mechanikus
mozgás, a homérséklet és a vízhasználat kis,
pamut és muszálas holmikat tartalmazó töltetre van
optimalizálva (lásd "programtáblázat"). Az
opció használatával rövidebb ido alatt, víz- és
energiatakarékosan moshat. Javasoljuk, hogy
használjon folyékony mosószert a töltet
mennyiségéhez illo adagban.
Ez a funkció nem használható a 1, 2, 7, 8, 9, 10,
11, 12, 13,
, , programok.
Az funkció a mosandó ruhák mosóvizének
fel nem melegítésével energiát takarít meg ez
elõnyös mind a környezet, mind a villanyszámla
szempontjából. Valóban, a fokozott teljesítmény és
az optimalizált vízfogyasztás kitûnõ eredményt
biztosít normál ciklus átlagos idõtartama alatt. A
legjobb mosási eredmény elérése érdekében
folyékony mosószer használatát javasoljuk.
Ez a funkció nem használható a 1, 7, 8, 10, 11, 12,
13,
, , programoknál.
Extra öblítés
Ezen opció alkalmazásával az öblítés, valamint a
végsõ mosószereltávolítás hatékonysága.
Használata a különösen érzékeny bõrû embereknél
ajánlott.
Ez a funkció nem használható a 10,
,
programoknál.
Vasaláskönnyítés
Ez a funkció a gyûrõdések keletkezésének
csökkentése érdekében a megfelelõ idõben módosítja
a mosási beállításokat és a centrifugasebességet. A
VASALÁSKÖNNYÍTÉS lámpa és az ELINDÍTÁS/
SZÜNETELTETÉS lámpa (az elsõ zöld, a második
narancssárga fénnyel) villogni kezd. A program
befejezéséhez nyomja meg az ELINDÍTÁS/
SZÜNETELTETÉS gombot vagy a
VASALÁSKÖNNYÍTÉS gombot. A 8 programnál a
készülék a mosandó ruhák áztatásánál leáll, a
VASALÁSKÖNNYÍTÉS lámpa és az ELINDÍTÁS/
SZÜNETELTETÉS lámpa villogni kezd. Az öblítõvíz
leeresztéséhez és a mosott ruhák kiszedéséhez meg
kell nyomni az ELINDÍTÁS/SZÜNETELTETÉS gombot,
vagy a VASALÁSKÖNNYÍTÉS gombot.
Ez a funkció nem használható a 7, 10, 11, 12, 13,
, . programoknál.
A táblázatban szereplõ értékek tájékoztató jellegûek.
A viszgálószervek számára:
1) EN60456 szabvány szerinti vezérlõprogramok: állítsa be a 2-os programot 60°C-ra.
2) Hosszú pamut program: állítsa be a 2-es programot 40°C-ra.
3) Rövid pamut program: állítsa be a 4-es programot 40°C-ra.
Õ
õ
õ
õ
õ
õ
õ
õ
õ
õ
õ
õ
õ
û
û
û
û
õ
õ
HU
Mosószerek és mosandók
Mosószer-adagoló fiók
A mosás eredményessége függ a mosószer helyes
adagolásától is: ha túl sokat adagol belõle, a mosás
nem lesz hatékonyabb, de hozzájárul ahhoz, hogy
lerakódás képzõdjön a mosógépben, valamint a
környezetet is jobban szennyezi.
! Ne használjon kézi mosószert, mert túlzottan sok
hab képzõdik.
Húzza ki a mosószer-
adagoló fiókot, és a
következõk szerint tegye
bele a mosószert, illetve
az adalékot.
1-es rekesz: Mosószer elõmosáshoz (por)
2-es rekesz: Mosószer mosáshoz (por vagy folyadék)
A folyékony mosószert csak az indítás elõtt lehet
betölteni.
3-as rekesz: Adalékok (öblítõk stb.)
Az öblítõ ne érjen a rács fölé.
A mosandó ruhák elõkészítése
Osztályozza a mosandókat a következõk szerint:
- Szövet típusa / címkén lévõ szimbólum.
- Színek Válogassa külön a színes és fehér ruhákat.
Ürítse ki a zsebeket, és vizsgálja meg a gombokat.
Ne lépje túl a mosandók száraz súlyára
vonatkozóan megadott értékeket:
Magasabb hõmérsékleten mosható anyagok: max. 6kg
Mûszálas anyagok: max. 2,5kg
Kényes anyagok: max. 2kg
Gyapjú: max. 1kg
Selyem: max. 1kg
Milyen nehezek a mosandó ruhák?
1 lepedõ: 400500g
1 párnahuzat: 150200g
1 asztalterítõ: 400500g
1 fürdõköpeny: 9001200g
1 törölközõ: 150250g
Különleges programok
Gyapjú: A 7-os programmal gyapjúholmikat lehet
mosni, azokat is, melyek címkéjén a csak kézzel
mosható
utasítás szerepel. A legjobb eredmény
elérése érdekében használjon speciális mosószert,
és ne lépje túl az 1 kg ruhatöltetet.
Selyem: az összes selyem ruhadarab mosásához
használja az ehhez való, 8-es programot! A
kényesebb ruhanemûkhöz tanácsos speciálisan
rájuk kifejlesztett mosószert használni.
Függönyök: hajtogatva tegye párnahuzatba
(vászonzsákba) vagy hálós zacskóba. Használja a
8-es programot.
Jeans: A mosás elõtt fordítsa ki a ruhadarabokat,
és használjon folyékony mosószert. Használja a 9-
as programot.
Express: ez a program enyhén koszos ruhadarabok
rövid idõ alatt történõ kimosására lett kifejlesztve
mindössze 15percig tart, így energiát és idõt takarít
meg. Az 10-ös programot 30°C-ra beállítva
különbözõ jellegû anyagokat együttesen is lehet
mosni (kivéve gyapjút és selymet) maximum 1,5kg
ruhatöltet-mennyiségig.
A Sport Intensive programot (11-es program) az
nagyon koszos sportruházatok (melegítõk, rövid
nadrágok stb.) mosására tervezték. A legjobb
eredmény érdekében javasoljuk, hogy ne lépje túl a
programtáblázat-ban feltüntetett maximális töltetet.
A Sport Light programot (12-es program) az enyhén
koszos sportruházatok (melegítõk, rövid nadrágok
stb.) mosására tervezték. A legjobb eredmény
érdekében javasoljuk, hogy ne lépje túl a
programtáblázat-ban feltüntetett maximális töltetet.
Javasoljuk, hogy használjon folyékony mosószert
féladagnak megfelelõ adagban.
A Sport Shoes programot (13-as program) a
sportcipõk mosására tervezték. A legjobb eredmény
érdekében ne mosson egyszerre 2 párnál többet.
A bepakolt ruhák kiegyensúlyozására
szolgáló rendszer
A túlzott zajhatás megelõzésére, valamint a
mosandók egyenletes eloszlása érdekében a
forgódob a centrifugafázis elõtt a mosási
centrifugasebességnél kicsit nagyobb sebességre
kapcsol. Amennyiben a töltet kiegyensúlyozására
irányuló próbálkozások nem vezetnek eredményre, a
készülék az elméleti centrifugasebességnél lassabb
centrifugálásra kapcsol. Jelentõs
kiegyensúlyozatlanság esetén a mosógép,
centrifugálás elõtt megpróbálja a töltetet
megfelelõen eloszlatni. A töltet megfelelõ
eloszlásának biztosítása érdekében ajánlatos a
nagy ruhanemûket a kicsikkel összekeverni.
1
2
3
1 / 1

Indesit IWSE 6108 ECO (EE) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi