Asus ZS661KS Mode d'emploi

Taper
Mode d'emploi
E16472
First Edition / May 2020
First Edition/ May 2020
ASUS Phone (Mobile Phone)
Model: ASUS_I003D (ZS661KS)
Before you start, ensure that you have read all the safety
information and operating instructions in this User Guide to
prevent injury or damage to your device.
NOTE: For the complete E-Manual and more detailed
information, refer to https://www.asus.com/support/.
Front features
Touch screen
display
Receiver & Speaker
Front camera
Proximity
sensor and
light sensor
Fingerprint
sensor
LED
indicator
Speaker
Side & Rear features
Microphone
Microphone
USB Type-C port
Rear cameras
Rear cover
NFC
detection
area
Camera ash
Aura light
Nano SIM
card slot
Side Mount
connector
Nano SIM
card tray
eject hole
AirTrigger
touch sensor
Power key
Volume key
AirTrigger
touch sensor
Microphone
Bumper RGB LED
NOTES:
The USB Type-C port supports USB 2.0 transfer rate. The
Side Mount connector Type-C port supports USB 3.1 Gen1
transfer rate.
Go to Settings > Advanced > AirTriggers to set
AirTriggers.
Microphone
USB Type-C
port
Audio jack
To install AeroActive Cooler:
1. Place your smartphone in a horizontal position.
2. Place the AeroActive Cooler on the back side of your phone
with the ROG logo facing outwards.
3. Insert the USB plug of the AeroActive Cooler into the Side
Mount connector of your Phone.
4. Push the top part of the AeroActive Cooler and snap the clip
on the top side.
Fan
Aura
light
Side mount
connector
cover
storage
NOTES:
Connect your AeroActive Cooler to the Side Mount
connector of your ROG Phone.
We recommend that you put your side mount connector
cover into the side mount connector cover storage
to avoid missing while connecting the side mount
connector.
You can use your AeroActive Cooler while using the
bundled ROG Phone 3 Case.
AeroActive Cooler features
Use the AeroActive Cooler to keep your ROG Phone working at
a high frequency during heavy workloads by providing a better
thermal solution, and oering the ultimate user experience.
Charging your ROG Phone
To charge your ROG Phone:
1. Connect the USB connector into the power adapter’s USB
port.
2. Connect the other end of the USB Type-C cable to your ROG
Phone.
3. Plug the power adapter into a wall socket.
NOTES:
It is not recommended that you connect other devices
to your ROG Phone when you install the phone on the
AeroActive Cooler.
Docking your ROG Phone on an accessory with fan(s) will
impact the audio quality when making phone calls and
recording.
or
1
2
3
To use the kickstand of AeroActive Cooler:
Open the kickstand on the back of the AeroActive Cooler to
get optimal viewing experience.
3
1
2
USB Type-C port
* DO NOT insert a USB Type-C cable to
this port.
NOTES:
For safety purposes, use ONLY the bundled power adapter
and cable to avoid damaging your device and prevent the
risk of injury.
For safety purposes, use ONLY the bundled power adapter
and cable to charge your ROG Phone.
The input voltage range between the wall outlet and this
adapter is AC 100V - 240V. The output voltage of the USB
Type-C cable is +5V-10V 3A, 30W.
IMPORTANT!
When using your ROG Phone while it is plugged to a power
outlet, the grounded power outlet must be near to the unit
and easily accessible.
When charging your ROG Phone through your computer,
ensure that you plug the USB Type-C cable to your
computer’s USB port.
DO NOT charge your ROG phone underwater or when the
USB connector is wet.
Avoid charging your ROG Phone in an environment with
ambient temperature of above 35 °C (95 °F).
or
NOTES:
We recommend that you charge your ROG phone through
one USB Type-C port at a time.
Only the Side Mount connector has Display Port
functionality.
If you connect USB Type-C OTG or charging devices to
both of the USB Type-C ports on your ROG phone, the
Side Mount connector will become the master and the
charging current or OTG device on the bottom port will
be limited.
3
1
2
1. Push a pin into the hole on the Nano SIM card tray to eject it.
Insert the Nano SIM card(s) into the card slot(s).
Installing a Nano SIM card
To install a Nano SIM card:
2. Push the tray to close it.
Nano-SIM1
Nano-SIM2
CAUTION!
Do not use sharp tools or solvent on your device to avoid
scratches on it.
Use only a standard Nano SIM card on your ROG Phone.
NOTES:
Both Nano SIM card slots support GSM/GPRS/EDGE,
WCDMA/HSPA+/DC-HSPA+, FDD-LTE, TD-LTE, and 5G NR
Sub-6 network bands. Both Nano SIM cards can connect to
VoLTE 4G calling service, but only one can connect to 5G NR
Sub-6 data service at a time.
Actual network and frequency band usage depends on
network deployment in your area. Contact your telecom
carrier if 5G NR Sub-6 support and VoLTE 4G calling service
are available in your area.
Federal Communications Commission
Statement
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Changes or modications not expressly approved by the party
responsible for compliance could void the user‘s authority to
operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
The antenna(s) used for this transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.
The country code selection is for non-US models only and is not
available to all US models. Per FCC regulation, all WiFi products
that are marketed in US must be xed to US-operated channels
only.
The responsible party within the USA per 47 CFR Part 2.1077(a)(3):
ASUS COMPUTER INTERNATIONAL (America)
Address: 48720 Kato Rd., Fremont, CA 94538, USA
Telephone: +1-510-739-3777
RF Exposure Information (SAR)
This device has been tested and meets applicable limits for Radio
Frequency (RF) exposure.
Specic Absorption Rate (SAR) refers to the rate at which the body
absorbs RF energy. SAR limits are 1.6 Watts per kilogram (over a
volume containing a mass of 1 gram of tissue) in countries that
follow the United States FCC limit and 2.0 W/kg (averaged over
10 grams of tissue) in countries that follow the Council of the
European Union limit. Tests for SAR are conducted using standard
operating positions with the device transmitting at its highest
certied power level in all tested frequency bands.
To reduce exposure to RF energy, use a hands-free accessory or
other similar option to keep this device away from your head
and body. Carry this device at least 15 mm away from your
body to ensure exposure levels remain at or below the as-tested
levels. Choose the belt clips, holsters, or other similar body-worn
accessories which do not contain metallic components to support
operation in this manner. Cases with metal parts may change
the RF performance of the device, including its compliance with
RF exposure guidelines, in a manner that has not been tested or
certied, and use such accessories should be avoided.
The highest FCC SAR values for the device (ASUS_I003D) are as
follows:
1.17 W/Kg @1g(Head)
1.19 W/Kg @1g(Body)
The FCC has granted an Equipment Authorization for this device
with all reported SAR levels evaluated as in compliance with the
FCC RF exposure guidelines. SAR information on this device is
on le with the FCC and can be found under the Display Grant
section of www.fcc.gov/oet/ea/fccid after searching on FCC ID:
MSQI003D .
FCC Statement (HAC)
This phone has been tested and rated for use with hearing aids
for some of the wireless technologies that it uses. However, there
may be some newer wireless technologies used in this phone that
have not been tested yet for use with hearing aids. It is important
to try the dierent features of this phone thoroughly and in
dierent locations, using your hearing aid or cochlear implant, to
determine if you hear any interfering noise. Consult your service
provider or the manufacturer of this phone for information on
hearing aid compatibility. If you have questions about return or
exchange policies, consult your service provider or phone retailer.
The Federal Communications Commission has implemented rules
and a rating system designed to enable people who wear hearing
aids to more eectively use these wireless telecommunications
devices. The standard for compatibility of digital wireless phones
with hearing aids is set forth in American National Standard
Institute (ANSI) standard C63.19-2011. There are two sets of ANSI
standards with ratings from one to four (four being the best
rating): an “M” rating for reduced interference making it easier
to hear conversations on the phone when using the hearing aid
microphone, and a “T rating that enables the phone to be used
with hearing aids operating in the telecoil mode thus reducing
unwanted background noise.
The Hearing Aid Compatibility rating is displayed on the wireless
phone box.
A phone is considered Hearing Aid Compatible for acoustic
coupling (microphone mode) if it has an “M3” or “M4” rating. A
digital wireless phone is considered Hearing Aid Compatible for
inductive coupling (telecoil mode) if it has a “T3” or T4” rating.
The tested M-Rating and T-Rating for this device (ASUS_I003D)
are M3 and T4.
You’ll want to try a number of wireless phones so that you can
decide which works the best with your hearing aids. You may also
want to talk with your hearing aid professional about the extent
to which your hearing aids are immune to interference, if they
have wireless phone shielding, and whether your hearing aid has
a HAC rating.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada’s licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux normes CNR d’Industrie
Canada applicables aux appareils radio exempts de licence. Son
utilisation est sujette aux deux conditions suivantes :
(1) Cet appareil ne doit pas créer d’interférences nuisibles, et
(2) Cet appareil doit tolérer tout type d’interférences, y compris
celles susceptibles de provoquer un fonctionnement non
souhaité de l’appareil.
This device for operation in the band 5150-5250 MHz is only for
indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont
réservés uniquement à une utilisation en intérieur an de réduire
les risques d’interférence préjudiciables aux systèmes de satellites
mobiles utilisant les mêmes canaux.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the
Industry Canada (IC) radio frequency exposure limits. The Wireless
Device should be used in such a manner such that the potential
for human contact during normal operation is minimized.
This device (ASUS_I003D) has been evaluated for and shown
compliant with the IC Specic Absorption Rate (“SAR”) limits when
installed in specic host products operated in portable exposure
conditions.
Canadas REL (Radio Equipment List) can be found at the following
web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.
do?lang=eng.
Additional Canadian information on RF exposure also can be
found at the following web address: http://www.ic.gc.ca/eic/site/
smt-gst.nsf/eng/sf08792.html.
This equipment should be installed and operated with minimum
distance 15 mm between the radiator and your body.
Cet appareil doit être installé et utilisé avec une distance minimale
de 15 mm entre l’ émetteur et votre corps.
Informations concernant lexposition aux fréquences radio
(RF)
La puissance de sortie émise par cet appareil sans l est inférieure
à la limite d’exposition aux fréquences radio d’Industrie Canada
(IC). Utilisez l’appareil sans l de façon à minimiser les contacts
humains lors d’un fonctionnement normal.
Cet appareil été évalué et démontré conforme aux limites de DAS
(Débit d’absorption spécique) d’IC lorsqu’il est installé dans des
produits hôtes particuliers qui fonctionnent dans des conditions
d’exposition à des appareils portables.
Ce périphérique est homologué pour l’utilisation au Canada.
Pour consulter l’entrée correspondant à l’appareil dans la liste
d’équipement radio (REL - Radio Equipment List) d’Industrie
Canada rendez-vous sur :
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng.
Pour des informations supplémentaires concernant l’exposition
aux ondes radio au Canada, rendez-vous sur :
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html.
CAN ICES-3(B)/NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
This device and its antenna(s) must not be co-located or operated
in conjunction with any other antenna or transmitter, except
tested built-in radios.
The County Code Selection feature is disabled for products that
are marketed in the US/ Canada.
Cet appareil et son ou ses antenne(s) ne doivent pas être situés
près de ou utilisés conjointement avec une autre antenne ou un
autre émetteur, exception faite des radios intégrées qui ont été
testées.
La fonction de sélection de l’indicatif du pays est désactivée pour
les produits commercialisés aux États-Unis et au Canada.
The IC ID for this device (ASUS_I003D) is 3568A-I003D.
L’identiant Industrie Canada de cet appareil (ASUS_I003D) est:
3568A-I003D.
Using GPS (Global Positioning System) on
your ROG Phone
To use the GPS positioning feature on your ROG Phone:
Ensure that your device is connected to the Internet before
using Google Map or any GPS-enabled apps.
For rst-time use of a GPS-enabled app on your device,
ensure that you are outdoors to get the best positioning
data.
When using a GPS-enabled app on your device inside a
vehicle, the metallic component of the car window and
other electronic devices might aect the GPS performance.
Prevention of Hearing Loss
To prevent possible hearing damage, do not listen at high volume
levels for long periods.
Safety information
CAUTION! Use of controls or adjustments or performance
of procedures other than those specied herein may result in
hazardous radiation exposure.
ROG Phone care
Use your ROG Phone in an environment with ambient
temperatures between 0 °C (32 °F) and 35 °C (95 °F).
The battery
WARNING: Disassembling the battery by yourself will void its
warranty and may cause serious harm.
Your ROG Phone is equipped with a high performance non-
detachable Li-polymer battery. Observe the maintenance
guidelines for a longer battery life.
Do not remove the non-detachable Li-polymer battery as
this will void the warranty.
Avoid charging in extremely high or low temperature. The
battery performs optimally in an ambient temperature of +5
°C to +35 °C.
Do not remove and replace the battery with a non-approved
battery.
Use only ASUS battery. Using a dierent battery may cause
physical harm/injury and may damage your device.
Do not remove and soak the battery in water or any other
liquid.
Never try to open the battery as it contains substances that
might be harmful if swallowed or allowed to come into
contact with unprotected skin.
Do not remove and short-circuit the battery, as it may
overheat and cause a re. Keep it away from jewelry or metal
objects.
Do not remove and dispose of the battery in re. It
could explode and release harmful substances into the
environment.
Do not remove and dispose of the battery with your regular
household waste. Take it to a hazardous material collection
point.
Do not touch the battery terminals.
To avoid re or burns, do not disassemble, bend, crush, or
puncture the battery.
NOTES:
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
The charger
Use only the charger supplied with your ROG Phone.
Never pull the charger cord to disconnect it from the power
socket. Pull the charger itself.
Caution
Your ROG Phone is a high quality piece of equipment. Before
operating, read all instructions and cautionary markings on the
(1) AC Adapter.
Do not use the ROG Phone in an extreme environment where
high temperature or high humidity exists. The ROG Phone
performs optimally in an ambient temperature between 0 °C
(32 °F) and 35 °C (95 °F).
Do not disassemble the ROG Phone or its accessories. If
service or repair is required, return the unit to an authorized
service center. If the unit is disassembled, a risk of electric
shock or re may result.
Do not short-circuit the battery terminals with metal items.
Operator access with a tool
If a TOOL is necessary to gain access to an OPERATOR ACCESS
AREA, either all other compartments within that area containing
a hazard shall be inaccessible to the OPERATOR by the use of the
same TOOL, or such compartments shall be marked to discourage
OPERATOR access.
Regional notice for Singapore
This ROG Phone complies with IMDA
Standards.
General Usage (typical body-worn) (for
Japan)
This device (front & rear side) should be operated under a
seperation distance of 15 mm from the human body.
* The other four sides are not in close proximity to the human
body at the general use as described above.
5GHz band (W52,W53): Indoor use only (Except for the 5.2GHz
transmission with High Power Data Communication System Base
Station or Relay Station).
5.2/5.3GHz 屋内使用限定 (高出力シ通信する場合を).
India E-waste (Management) Rules 2016
This product complies with the “India E-Waste (Management)
Rules, 2016” and prohibits use of lead, mercury, hexavalent
chromium, polybrominated biphenyls (PBBs) and polybrominated
diphenyl ethers (PBDEs) in concentrations exceeding 0.1%
by weight in homogenous materials and 0.01 % by weight in
homogenous materials for cadmium, except for the exemptions
listed in Schedule II of the Rule.
電波障害自主規制について
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の
基準に基づく クラス B 情報技術装置です。この装置は、家庭環境
で使用することを目的として いますが、この装置がラジオやテ
レビジョン受信機に近接して使用されると、 受信障害を引き起
こすことがあります。   取り扱い説明書に従って正しい取り扱
いをしてください。
この装置は、クラスB情報技術装置です。この装置は
家庭環境で使用することを目的としていますが、
の装置がラジオやテレビジョン受信機に近接して使
用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。VCCI-B
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our
commitment to the highest standards for protecting our
environment. We believe in providing solutions for you to be able
to responsibly recycle our products, batteries, other components
as well as the packaging materials. Please go to http://csr.asus.
com/english/Takeback.htm for detailed recycling information in
dierent regions.
India BIS - IS 16333 Notice
Language Input : Hindi, English, Tamil
Readability: Assamese, Bangla, Bodo(Boro), Dogri, Gujarati, Hindi,
Kannada, Kashmiri, Konkani,
Maithili, Malayalam, Manipuri(Bangla), Manipuri(Meetei Mayek),
Marathi, Nepali, Oriya, Panjabi, Santhali, Sanskrit, Sindhi (Devanagari),
Tamil, Telugu, Urdu and English
Proper disposal
Risk of explosion if battery is replaced by
an incorrect type. Dispose of used batteries
according to the instructions.
DO NOT throw the battery in municipal waste. The
symbol of the crossed out wheeled bin indicates
that the battery should not be placed in municipal
waste.
DO NOT throw this product in municipal waste.
This product has been designed to enable proper
reuse of parts and recycling. The symbol of
the crossed out wheeled bin indicates that the
product (electrical, electronic equipment and
mercury-containing button cell battery) should
not be placed in municipal waste. Check local
regulations for disposal of electronic products.
DO NOT throw this product in re. DO NOT short
circuit the contacts. DO NOT disassemble this
product.
WARNING
Cancer and Reproductive Harm-
www.P65Warnings.ca.gov
NOTE: For more legal and e-labelling information, check on
your device from Settings > About > Legal information /
Regulatory labels.
TouchSense® Technology licensed from Immersion Corporation
and protected under one or more of the U.S. Patents found at the
following address
www.immersion.com/patent-marking.html and other patents
pending.
FCC COMPLIANCE INFORMATION
Per FCC Part 2 Section 2.1077
Responsible Party:
Asus Computer International
Address: 48720 Kato Rd, Fremont, CA 94538
Phone/Fax No:
(510)739-3777/(510)608-4555
hereby declares that the product
Product Name :
ASUS ROG Phone 3
Model Number :
ASUS_I003D
compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Ver. 180620
Copyright © 2020 ASUSTeK COMPUTER INC.
All Rights Reserved.
You acknowledge that all rights of this Manual remain with ASUS. Any and all rights,
including without limitation, in the Manual or website, and shall remain the exclusive
property of ASUS and/or its licensors. Nothing in this Manual intends to transfer any
such rights, or to vest any such rights to you.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED
FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME
WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS.
ASUS
Address: 1F., No.15, Lide Rd., Beitou Dist., Taipei City 112,
Taiwan
Tel: 886228943447
Fax: 886228907698
Declaration
We declare that the IMEI codes for this product, ROG Phone, are
unique to each unit and only assigned to this model. The IMEI of
each unit is factory set and cannot be altered by the user and that
it complies with the relevant IMEI integrity related requirements
expressed in the GSM standards.
Should you have any questions or comments regarding this matter,
please contact us.
Sincerely yours,
ASUSTeK COMPUTER INC.
Tel: 886228943447
Fax: 886228907698
Support: https://www.asus.com/support/
ZenTalk Fans Forum
(http://www.asus.com/zentalk/global_forward.php)
15060-XXXXXXXX
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Asus ZS661KS Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues