Q-tran Q-TRAN LQTM-eLED+AW LED Power Supply Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

INSTALLATION LED POWER SUPPLY - QTM-eLED+AW
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-05-12-22
HORIZONTAL VERTICAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stacked
More Units can be stacked
More Units can be stacked
NOTE:
Rods not included.
RECESSED
SURFACE
ROD SUSPENSION
(Horizontal)
ROD SUSPENSION
(Vertical)
VERTICAL
Double Sided
Key Hole
1/4" Rod Thru Hole
3/8" Rod Thru Hole
NOTE: Bracket can also be mounted (Top & Bottom) for Vertical Mounts.
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
4.00"
BOTTOM VIEW
14.5"
8.00" 4.00"
ISOMETRIC VIEW
8.00"
Mounting Options
Housing
INSTALLATION LED POWER SUPPLY - QTM-eLED+AW
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-05-12-22
Input Load
NEU HOT GND
0 - 10V
DIM-MOD
0-10V
Output Load Output Load 0-10V
0 - 10V
DIM-MOD
0 - 10V
DIM-MOD
0 - 10V
DIM-MOD
0 - 10V DIM-MOD
R
D
B
L
R
D
B
L
R
D
B
L
R
D
B
L
LED DRIVER (120 - 277V) LED DRIVER (120 - 277V)
0 - 10V
DIM-MOD
Adjustable
White Module
LED DRIVER (120 - 277V)
HOT
NEU
INTENSITY
CCT
QTM-eLED+AW
: for interior
0-10V NEU HOT GND
0-10V
SECONDARY
PRIMARY
+24V
CW
iQ-LED
+24V Cool
RTN
Warm
RTN
GND
Driver with Dimming Module
INSTALLATION LED POWER SUPPLY - QTM-eLED+AW
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-05-12-22
CSA Requirements
Suitable for indoor use
This power supply must be installed according to the National Electric Code and local codes and ordinances and in
accordance with applicable installation code by a person familiar with the construction and operation of the product and
the hazards involved.
Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
To avoid a hazard to children, account for all parts and destroy all packaging materials.
WITH DIMMER
Model Input Voltage
(V)
Frequency Nominal Output
Voltage (VDC)
Nominal Output
Wattage (W)
Input Current
(A)
QTM-eLED-100
QTM-eLED-200
QTM-eLED-300
120
120
120
0.95
1.90
2.85
50/60
50/60
50/60
24
24
24
100
200
300
QTM-eLED-60
QTM-eLED-120
QTM-eLED-180
120
120
120
0.60
1.20
1.80
50/60
50/60
50/60
12
12
12
60
120
180
WIRE CONNECTION
WITHOUT DIMMER
WIRE CONNECTION
WITH DIMMER
Red = +24V
Blue = -24V
Red = +24V
White = -24V
Q-Tran, Inc.
Q-TRAN, INC.
MILFORD, CT U.S.A.
(203) 367-8777
WWW.Q-TRAN.COM
CLASS: 3425 - 15
3425 - 95
LOW VOLTAGE
LIGHTING SYSTEM
Type Ic Recessed, Inherently Protected
Type IC ENCASTRE, PROTECTION INHÉRENTE
● For Supply Connections Use Wire Rated
For At Least 60 C.
● Suitable For Damp Locations
CONVIENT AUX EMPLACEMENTS HUMIDES
● 50/60 Cycle
● Class 1 or Class 2
WARNING:
RISK OF FIRE. IF INSTALLATION INVOLVES RUNNING WIRE THROUGH A
BUILDING STRUCTURE, SPECIAL WIRING METHODS ARE NEEDED. CONSULT A QUALIFIED ELECTRICIAN
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION
PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET
SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
QTM-eLED
120V
INPUT VOLTAGE OUTPUT VOLTAGE
24V12V
CONTROL TYPE
0-10V
WITH DIMMER
Model Input Voltage
(V)
Frequency Nominal Output
Voltage (VDC)
Nominal Output
Wattage (W)
Input Current
(A)
QTM-eLED-100
QTM-eLED-200
QTM-eLED-300
120 / 277
120 / 277
120 / 277
0.95 / 0.40
1.90 / 0.80
2.85 / 1.20
50/60
50/60
50/60
24
24
24
100
200
300
QTM-eLED-60
QTM-eLED-120
QTM-eLED-180
120 / 277
120 / 277
120 / 277
0.60 / 0.29
1.20 / 0.58
1.80 / 0.87
50/60
50/60
50/60
12
12
12
60
120
180
WIRE CONNECTION
WITHOUT DIMMER
WIRE CONNECTION
WITH DIMMER
Red = +24V
Blue = -24V
Red = +24V
White = -24V
Q-Tran, Inc.
Q-TRAN, INC.
MILFORD, CT U.S.A.
(203) 367-8777
WWW.Q-TRAN.COM
CLASS: 3425 - 15
3425 - 95
LOW VOLTAGE
LIGHTING SYSTEM
Type Ic Recessed, Inherently Protected
● For Supply Connections Use Wire Rated
For At Least 60 C.
● Suitable For Damp Locations
● 50/60 Cycle
● Class 1 or Class 2
WARNING:
RISK OF FIRE. IF INSTALLATION INVOLVES RUNNING WIRE THROUGH
A BUILDING STRUCTURE, SPECIAL WIRING METHODS ARE NEEDED.
CONSULT A QUALIFIED ELECTRICIAN
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
QTM-eLED
120V - 277V
INPUT VOLTAGE OUTPUT VOLTAGE
24V12V
CONTROL TYPE
0-10V
  • Page 1 1
  • Page 2 2
  • Page 3 3

Q-tran Q-TRAN LQTM-eLED+AW LED Power Supply Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à