Modern Forms WS-57919 Ice Mode d'emploi

Taper
Mode d'emploi
1
INSTALLATION INSTRUCTIONS
     
WS-57919/WS-57919F/WS57927/WS-57927F/WS-57937/WS-57937F
      
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headqua rters/Eas tern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
                                                                               
                                                                    
Read all instructions before installing.
System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
Retain installation instructions for future maintenance reference.
     All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
            Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
                                                                      
Lisez toutes les instructions avant l’installation.
Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
     Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
            Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Plastic Anchor
Qty: 2pcs+1 Extra
Mounting Screw
Qty:1 Extra
5/32"-32x1/2
Nickel Plating
Wire Connector
Qty: 3pcs+1Extra
Spacer
Qty:2pcs+1Extra
ABCE
Conversion Plate
Qty:1pc
G
F
Mounting Ring
Qty:1pc
Wood Screw
Qty: 2pcs+1Extra
DH
Mounting Screw
Qty:2pcs+1 Extra
5/32"-32×1
2
INSTALLATION INSTRUCTIONS
     
WS-57919/WS-57919F/ WS-57927/WS 57927F/ WS-57937/WS-57937F
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
     
            
                 
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headqua rters/Eas tern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Wire Connector
A
Ground Wire
Wood Screw
Mitered Glass
(WS-57919/WS-57919F: RPL-GLA-57919)
(WS-57927/WS-57927F: RPL-GLA-57927)
(WS-57937/WS-57937F: RPL-GLA-57937)
Mounting Screw
B
Junction Box Screw
Mounting Back Plate
S
witch Box
Plastic Anchor
C
D
Junction Box
Mounting Ring
Junction Box Screw
F
Plastic Anchor
C
Spacer
E
Conversion Plate
G
Wood Screw
D
Mounting Screw
B
Mounting Back Plate
Mounting Screw
H
4 7/8"
WS-57919/WS-57919F:15 9/16"
WS-57927/WS-57927F:19 1/2"
WS-57937/WS-57937F:23 7/16"
WS-57919/WS-57919F:12 3/16"
WS-57927/WS-57927F:16 1/8"
WS-57937/WS-57937F:19 7/8"
1 3/8"
1 5/8"
8"
4 1/2"
1 3/8"
1 5/8"
1 3/8"
1 3/4"
Ø4"
                                               
                                                                                  
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNT ON 2”x4” SWITCH BOX (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Drill holes in the wall aligned with the key hole located in the mounting plate, insert the plastic anchor (C).
5. Connect the fixture’s wires to switch box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet box has
a green or bare copper ground wire, connect the fixtures ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
6. Secure the mounting plate to the switch box using junction box screws, fasten it to the wall using wood screw (D). The side of the
mounting plate marked “GND” must face out.
7. Place the fixture on the mounting back plate and secure it with mounting screw (B).
OR
MOUNT ON 4”x4”JUNCTION BOX (Fig. 2)
3. Remove the mounting screw (B) from the fixture.
4. Drill holes in the wall aligned with the key hole located in the mounting plate, insert the plastic anchor (C).
5. Connect the fixture’s wires to junction box wires as shown in Fig. 3, making sure that all wire connectors (A) are
secured. If your outlet box has a green and bare copper ground wire, connect the fixture’s ground wire to it. Otherwise,
connect the fixture’ ground wire directly to back plate using the green screw provided.
6. Secure the mounting ring (F) to the junction box using junction box screws, the side of the mounting plate marked “GND” must face out.
7. Secure the mounting plate and conversion plate (G) to the mounting ring with mounting strew (H), fasten the mounting back plate to the
wall using wood screw (D) and spacer (E).
8. Place the fixture on the mounting back plate and secure it with mounting screw (B).
3
INSTALLATION INSTRUCTIONS
579-Wall Sconce
WS-57919/WS-57919F/ WS-57927/WS 57927F/ WS-57937/WS-57937F
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
  • Page 1 1
  • Page 2 2
  • Page 3 3

Modern Forms WS-57919 Ice Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues