Baumer R600V Multi-Object Radar Sensor Mode d'emploi
- Taper
- Mode d'emploi
Radar Sensoren
Radar sensors
Détecteurs à radar
Multiobjekt Radarsensor
Multi-object radar sensor
Détecteur radar de multi-objet
Technische Daten Technical data Données techniques
Erfassungsbereich Sd 0,3 ... 8,5 m sensing distance Sd 0,3 ... 8,5 m Portée de détection Sd 0,3 ... 8,5 m
Önungswinkel 6° (3dB) aperture angle 6° (3dB) Angle d‘ouverture 6° (3dB)
Betriebsspannungsbereich
+Vs
9 ... 32 VDC voltage supply range
+Vs
9 ... 32 VDC Plage de tension +Vs 9 ... 32 VDC
Stromaufnahme max.
(ohne Last)
160 mA current consumption
max. (no load)
160 mA Consommation max.
(sans charge)
160 mA
Ausgangsschaltung CAN (5V) output circuit CAN (5V) circuit de sortie CAN (5V)
logische Schnittstelle CAN SAE J1939 logical interface CAN SAE J1939 interface logique CAN SAE J1939
Baud Rate 250 kBaud (500 kBaud) baud rate 250 kBaud (500 kBaud) vitesse de transmission 250 kBaud (500 kBaud)
kurzschlussfest ja short circuit protection yes Protégé contre courts-cir-
cuits
oui
verpolungsfest ja, Vs zu GND reverse polarity pro-
tection
yes, Vs to GND Protégé contre inversion
polarité
oui, Vs vers GND
Arbeitstemperatur -40 ... +70 °C operating temperature -40 ... +70 °C Température de foncti-
onnement
-40 ... +70 °C
Lagertemperatur -40 ... +85 °C storage temperature -40 ... +85 °C Température de stockage -40 ... +85 °C
Schutzart IP 68/69K protection class IP 68/69K Classe de protection IP 68/69K
R600V.DAH5-11221283
Abmessungen Dimensions Dimensions Elektrischer Anschluss Schéma de raccordement
• Alle Masse in mm
• All dimensions in mm
• Toutes les dimensions en mm
• Vor dem Anschliessen des Sensors die Anlage spannungsfrei schalten.
• Disconnect power before connecting the sensor.
• Mettre l`installation hors tension avant le raccordement du détecteur.
Connection diagram
1/4
Technische Änderungen vorbehalten Tecnical specications subject to change Sous réserve de modications techniques
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTICE: Changes or modications made to this equipment not expressly approved by Baumer may void the FCC authorization
to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Radiofrequency radiation exposure Information: This equipment complies with FCC exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canada Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two condi-
tions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. This equipment complies with IC radiation exposure limits set forth for an un-
controlled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator
and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence. L‘exploita-
tion est autorisée aux deux conditions suivantes: (1) l‘appareil ne doit pas produire de brouillage, et (2) l‘appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d‘en compromettre le fonctionnement. Cet équipement
est conforme aux limites d‘exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Ce transmetteur
ne doit pas etre place au meme endroit ou utilise simultanement avec un autre transmetteur ou antenne.
82
97
84
6,8
2x
17,4
32
62
42 11
42
+Vs
(3)
(1)
(4)
0 V
CAN HI
(2)
CAN SAE
J1939 CAN LO
2 CAN HI
4 CAN LO
1 +Vs
3 GND
Status / Status / Condition Code
Sensor voll funktionfähig (Objekt detektiert)
Sensor fully operational (object detected)
Capteur complètement opérational (object détecté)
100 ms grüne LED an / green LED on / LED verte alluminée
900 ms LED aus / o / éteinte
Sensor voll funktionfähig (kein Objekt detektiert)
Sensor fully operational (no object detected)
Capteur complètement opérational (anun object détecté)
wie oben / as above / comme ci-dessus
zusätzlich / with additional / avec supplémentaire
100 ms gelbe LED an / yellow LED on / LED jaune alluminée
Elektronikfehler
Hardware fault
Défaut de matériel
50 ms rote LED an / red LED on / LED rouge alluminée
50 ms LED aus / o / éteinte
CAN Abwurf (Fehlfunktion)
CAN bus o (malfunction)
Arrêt du bus CAN (dysfonctionnement)
50 ms magenta LED an / on / alluminée
150 ms LED aus / o / éteinte
Adresszuweisung fehlgeschlagen
Address claim failed
Assigment d‘ addresse failli
50 ms magenta LED an / on / alluminée
50 ms LED aus / o / éteinte
Warten auf Adresszuweisung
Waiting for Master ECU adress claim
En attendre il assignment d‘ adresse du maître ECU
500 ms magenta LED an / on / alluminée
500 ms LED aus / o / éteinte
Andere / other / autre blaue LED / blue LED / LED bleue
Grundinformation CAN - basic information CAN -
informations de base CAN
ISO Name
ISO name
Nom ISO
Manufacturer code:
ECU instance:
Function instance:
Function:
System:
System instance:
Industry group:
Arbitration capable:
343 (Baumer Group)
0
3
255 (non specic)
127 (non specic)
0
2
1
Geräteadresse
Device address
Adresse de l‘appareil
Unterstützt / supports „commanded address“ /
supporte adresse commandée (PGN 0xFED8)
im Bereich / in range / dans l‘ interval:
0x80 ... 0xCF (Standard / default / défault 0x80)
Objektdistanzen CAN Nachrichten - object distances CAN messages - Messages CAN des distances d‘ objet
PGN CAN Nachrichten (für 8 Objekte) / CAN messages (for 8 objects) / Messages CAN (pour 8 objets) : 0xC000
Start bit Bits Abstand
oset
décaillage
Skalierung
scaling
écaillage
Beschreibung / description / description
1 2 0 1 Mulitiplexer / multiplexor / multiplexor n = {0, 1, 2, 3}
3 2 0 1 Sensorstatus / Sensor status / état de capteur
0 = Kein Fehler / no error / Pas d‘ erreur
1 = Reversibler Fehler / reversible error / erreur reversible
2 = Irreversibler Fehler / irreversible error / erreur irréversible
5 1 0 1 Objektstatus 2n+1 / object status 2n+1 / statut d‘ objet 2n+1
6 1 0 1 Objektstatus 2n+2 / object status 2n+2 / statut d‘ objet 2n+2
7 14 0 1 mm Objektdistanz 2n+1 / object distance 2n+1 / distance d‘ objet 2n+1
21 14 0 1 mm Objektdistanz 2n+2 / object distance 2n+2 / distance d‘ objet 2n+2
35 7 0 1 % Kondenz Objektdistanz 2n+1 / object distance condence 2n+1 /
conance en la distance par raportaux objet 2n+1 [0 … 100%]
42 7 0 1 % Kondenz Objektdistanz 2n+2 / object distance condence 2n+2 /
conance en la distance par raportaux objet 2n+2 [0 … 100%]
49 8 128 0.03125 m/s Objektgeschwindigkeit 2n+1 / object speed 2n+1 /
vitesse d‘ objet 2n+1 [-4 … 3.96875 m/s]
57 8 128 0.03125 m/s Objektgeschwindigkeit 2n+2 / object speed 2n+2 /
vitesse d‘ objet 2n+2 [-4 … 3.96875 m/s]
2/4
Visuelle Diagnose Visual diagnostic Diagnostic visuel
CAN Kommunikation - CAN communication - communication CAN
Für weitere Informationen lesen Sie bitte die Bedienungsanleitung - For further information please refer to the user manual - Pour plus d‘ informations, veuillez vous référer au manuel d‘ utilisation
12345678
F
E
D
C
B
A
ModMod
Rev Drawn Approved Rev Drawn Approved
deburred
Qty Item Pos. Material Remarks
Project
Replaced by
Replacement for
This drawing is OUR PROPERTY and may
not be copied, recreated or made available
to any third party without prior permission
Baumer Electric AG
Postfach · Hummelstrasse 17 · CH-8501 Frauenfeld
Phone +41 (0)52 728 11 22 · Fax +41 (0)52 728 11 44
Drawn
Checked
Approved
Scale
R600V.DAH5-11221283
Multi object radar sensor
11221283 A
10714028 Off Highway
Radar
a 13.01.2021 cg 13.01.2021 rma
RZ.00019
cg09.03.2020
rma09.03.2020
wemi31.08.2020
1:1
13. Jan. 2021 11:02
2
3
1
4
Mating Connector
AMPSEAL 16
776524-1
PIN 1 +Vs
PIN 2 CAN HI
PIN 3 GND
PIN 4 CAN LO
82 ±0,3
62 ±0,5
97 ±0,5
17,4 ±0,5
60°
center axis
42,5 ±0,5
32 ±0,5
84 ±0,5
R600V.DAH5-11xxxxxx
11xxxxxx
SN: xxxx.10.X-xxxx-xxxx
FCC ID: xxxxxx IC ID: xxxxxx HVIN: xxxxxx
Laser marked
6,8±0,2
20max. O
11 ±0,5 18,5
42 ±0,5
42 ±0,5 (Lens)
zero distance
NOTES:
1. ELECTRICAL SPECIFICATION:
a. VOLTAGE SUPPLY RANGE: 9V…32V (12VDC/24VDC VEHICLE POWER)
b. CURRENT CONSUMPTION: <160mA (averaged)
c. RADAR FREQUENCY: 122GHz…123GHz
2. OUTPUT FUNCTION:
a. CAN SAE J1939
b. BAUD RATE: 250/500kbaud
c. OUTPUT CIRCUIT: CAN without internal 120Ω terminator (5V CAN-SYSTEM)
d. CAN UPDATE RATE: ≥ 0.2Hz … ≤ 100 Hz
e. SENSING RANGE (FROM LENS FRONT): 300mm…8500mm
f. SENSING RANGE, STATIC TARGET: 390mm…8500mm (center axis)
g. BLIND RANGE: 300mm (object detection limited)
3. MECHANICAL DATA:
a. RECTANGULAR HOUSING: 97 x (84 +17.4) x 42.5mm
b. DIAMETER MOUNTING HOLES:6.8mm±0.2mm
c. RECOMMENDED SCREWS: M6 ACC. MBM 10105
d. INSTALLATION TORQUE: Screw with property class 10.9: max torque of screw
12Nm…15Nm, Screw with property class 8.8: max torque of screw 10Nm…12Nm
e. ENCLOSURE MATERIAL: POLYAMID (GLASS FIBRE REINFORCED)
f. MOUNTING PLATE: ALUMINUM (COATED WITH CATAPHORETIC PAINTING (KTL))
g. LENS MATERIAL: Polyetherimid (PEI)
4. AMBIENT CONDITIONS:
a. STORAGE TEMPERATURE: -40°C…+85°C
b. OPERATING TEMPERATURE: -40°C…+70°C
5. SENSOR MEETS FOLLOWING REQUIREMENTS OF EMC AND ENVIRONMENT ACC. FSP:
a. EMC AGRICULTURAL MACHINERY EN ISO 14982 (12V/24V-SYSTEM)
b. EMC CONSTRUCTION MACHINERY EN 13309 (12V/24V-SYSTEM)
c. EMC EARTH MOVING MACHINERY ISO 13766 (12V/24V-SYSTEM)
d. EUROPE: RADIO EQUIPMENT AND REPEALING DIRECTIVE (RED) 2014/53/EU
e. USA / CDN: COMPLIANCE STATEMENTS SEE PAGE 2, CHAPTER 11 OF THIS
DRAWING
f. EMC (INDUSTRIAL) EN 61000-6-2 / EN 61000-6-3
g. PROTECTION CLASS ISO 20653_2013: IP68/IP69K
h. PARTICLE IMPACT EN ISO 20567-1 (GRAVEL EN11124-2)
i. RANDOM VIBRATION IEC 60068-2-64 (5Hz…2000Hz, 11.55 Grms)
j. OPERATING MECHANICAL SHOCK IEC 60068-2-27 (50g)
6. PART IS MARKED WITH BAUMER LOGO; PART NUMBER; DATE CODE, SERIAL NUMBER
7. MOUNTING RECOMMENDATION:
a. REQUIRED FLATNESS OF THE SENSOR MOUNTING SURFACE ≤0.2mm/100mm
b. DIRECT MOUNTING ONTO A STEEL PLATE WITH A THICKNESS OF 6mm WITH TWO M6 SCREWS
c. INDIRECT MOUNTING ONTO A STEEL PLATE WITH A THICKNESS OF 3mm WITH TWO M6 SCREWS
AND TWO FLANGE NUTS
8. LED FUNCTIONS (LED INSIDE LENS)
a. SENSOR FULLY OPERATIONAL: GREEN LED blinking
b. NO OBJECT DETECTED: GREEN / YELLOW blinking
c. CAN BUS WAITING ON MASTER OR ERRORS: MAGENTA LED blinking
d. HW FAULT: RED LED blinking
9. INTENDED USE / APPLICATION POLICY:
a. The suitability and functionality of a Baumer product and its performance under different applications and / or
end-use cases can only be verified by testing, and shall ultimately be the responsibility of the customer.
b. The product shall not be used:
I. For functional safety applications and in potentially explosive atmospheres.
II. In the direct control and modification of the state of function of the machine.
c. Possible malfunctions and failed measurements of the sensor must be intercepted at the system level and shall
not lead to unsafe situations in the system.
d. The customer shall perform its own safety assessment to account for sensor behavior in particular situations
(e.g. distance fluctuations in static situations, operator caused distance manipulation by hand or other objects).
e. Safety relevant information must be communicated to the end-user.
10. INTEGRATION REMARKS:
Objects within a rotational cone of ± 30° may be picked up by the sensor depending on position and/or surface
properties. When mounting behind a cover material, properties and thickness must be taken into account to avoid
excessive damping of the signal. Coatings containing metal must be avoided.
1 / 2
3/4
12345678
F
E
D
C
B
A
ModMod
Rev Drawn Approved Rev Drawn Approved
deburred
Qty Item Pos. Material Remarks
Project
Replaced by
Replacement for
This drawing is OUR PROPERTY and may
not be copied, recreated or made available
to any third party without prior permission
Baumer Electric AG
Postfach · Hummelstrasse 17 · CH-8501 Frauenfeld
Phone +41 (0)52 728 11 22 · Fax +41 (0)52 728 11 44
Drawn
Checked
Approved
Scale
R600V.DAH5-11221283
Multi object radar sensor
11221283 A
10714028 Off Highway
Radar
a 13.01.2021 cg 13.01.2021 rma
RZ.00019
cg09.03.2020
rma09.03.2020
wemi31.08.2020
1:1
13. Jan. 2021 11:02
2 / 2
11. Compliance Statements:
a. FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTICE: Changes or modifications made to this equipment not expressly approved by
Baumer may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cau se
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Radiofrequency radiation exposure Information:
This equipment complies with FCC exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between
the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
b. Canada Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20
cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
Ce transmetteur ne doit pas être place au même endroit ou utilise simultanément avec un
autre transmetteur ou antenne.
4/4
-
1
-
2
-
3
-
4
Baumer R600V Multi-Object Radar Sensor Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Baumer R600V.DAH5-11205779 Mode d'emploi
-
-
-
-
-
Baumer RR30 Mode d'emploi
-
-
