Parkside PFSA 20-Li A1 Mode d'emploi

CORDLESS PAINT SPRAYER PFSA 20-Li A1

CORDLESS PAINT SPRAYER

Translation of the original instructions BATTERIDREVET SPRØJTEPISTOL

Oversættelse af den originale driftsvejledning

AKKU-FARBSPRITZPISTOLE

Originalbetriebsanleitung

PISTOLET À PEINTURE SANS FIL

Traduction des instructions d’origine

ACCU-VERFSPUITPISTOOL

Vertaling van de originele gebruiksaanwijzing

IAN 354661_2010

GB / IE/NI Translation of the original instructions Page 1

DK Oversættelse af den originale driftsvejledning Side 14

FR / BE Traduction des instructions d’origine Page 29

NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 43

DE / AT / CH Originalbetriebsanleitung Seite 57

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

Avant de lire le mode d'emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l'appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

5a

B

All Parkside tools and the chargers PLG 20 A1/PLG 20 A4/PLG 20 B1/PLG 20 A2/PLG 20 A3/

PDSLG 20 A1 of the X20V Team series are compatible with the PAP 20 A1/

PAP 20 A2/PAP 20 A3/PAP 20 B1/PAP 20 B3 battery pack.

Charging times

Charging currents

2 Ah

Battery pack

PAP 20 A1/B1

3 Ah

Battery pack

PAP 20 A2

4 Ah

Battery pack

PAP 20 A3/B3

max. 2.4 A

Charger PLG 20 A1/A4/B1

60 min

2,4 A

90 min

2,4 A

120 min

2,4 A

max. 3.5 A

Charger PLG 20 A2

45 min

3,5 A

60 min

3,5 A

80 min

3,5 A

max. 4.5 A

Charger PLG 20 A3

35 min

3,8 A

45 min

4,5 A

60 min

4,5 A

max. 4.5 A

Charger PDSLG 20 A1

35 min

3,8 A

45 min

4,5 A

60 min

4,5 A

PFSA 20-Li A1 GB│IE│NI │ 1 ■

Contents

Introduction ............................................................2

Intended use ........................................................................2

Features ...........................................................................2

Package contents ....................................................................2

Technical speciﬁcations ...............................................................2

General power tool safety warnings .......................................3

1. Work area safety ..................................................................4

2. Electrical safety ...................................................................4

3. Personal safety ....................................................................4

4. Power tool use and care ............................................................5

5. Use and handling of the cordless electrical power tool .....................................5

6. Service ..........................................................................5

Additional safety instructions for paint spray guns ........................... 6

Original accessories/auxiliary equipment .................................................6

Safety guidelines for battery chargers ....................................................7

Working procedures .................................................... 7

Viscosity ...........................................................................7

Preparing the spray surface ............................................................8

Before use ............................................................. 8

Charge battery pack (see ﬁg. B) ........................................................8

Attaching/disconnecting the battery pack to/from the appliance ...............................8

Checking the battery charge level .......................................................8

Setting up .............................................................8

Assembly/disassembly ................................................................8

Selecting/changing the nozzle .........................................................8

Filling with spray material ..............................................................9

Switching the appliance on/oﬀ .........................................................9

Adjust spray pattern ..................................................................9

Selecting a jet type ...................................................................9

Maintenance and cleaning ................................................9

Cleaning/replacing the air ﬁlter ........................................................10

Disposal .............................................................. 10

Kompernass Handels GmbH warranty ....................................11

Service ............................................................... 12

Importer .............................................................12

Original Declaration of Conformity .......................................13

Ordering a replacement battery .......................................... 14

Telephone ordering .................................................................14

PFSA 20-Li A1

■ 2 │ GB│IE│NI

CORDLESS PAINT SPRAY GUN

PFSA 20-Li A1

Introduction

Congratulations on the purchase of your new

appliance. You have chosen a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product,

please familiarise yourself with all of the operating

and safety instructions. Use the product only as

described and for the range of applications spec-

iﬁed. Please also pass these operating instructions

on to any future owner.

Intended use

This appliance is suitable for applying paint,

lacquers and glazes. The use of easily ﬂammable,

combustible paints, lacquers or thinners is strictly

prohibited. Any other usage or modiﬁcation of the

appliance is deemed to be improper and carries

a signiﬁcant risk of accidents. The manufacturer

accepts no responsibility for damage(s) resulting

from improper usage. This appliance is intended

for domestic use only.

Features

(see illustration on fold-out page)

Union nut

Nozzle head

Nozzle

Spray unit

Trigger

5a

Catch

Motor unit

Screws

Air ﬁlter cover

Air ﬁlter

Paint cup

Riser pipe

Spray volume adjusting wheel

Fig. A

Cleaning brush

Cleaning needle

Measuring cup

Replacement air ﬁlter

Fig. B

Battery pack*

Release button

Battery charge level button

High-speed charger*

Red control LED

Green control LED

Package contents

1 cordless paint spray gun

2 nozzles *1 1 x 1.8 mm, 1 x 2.6 mm

1 viscosity measuring cup

1 cleaning needle

1 cleaning brush

1 set of operating instructions

1 ﬁlter

*1 1 x preﬁtted

Technical speciﬁcations

Cordless paint spray gun PFSA 20-Li A1

Rated voltage 20 V (DC)

Flow rate 700 ml/min (water)

Paint cup 1000 ml

Max. viscosity 70 DIN/s

Battery PAP 20 A1*

Type LITHIUM ION

Rated voltage 20 V (DC)

Capacity 2 Ah

Cells 5

PFSA 20-Li A1 GB│IE│NI │ 3 ■

High-speed battery charger PLG 20 A1*

INPUT

Rated voltage 230–240 V ∼, 50 Hz (AC)

Rated power

consumption 65 W

Fuse (internal) 3.15 A

T3.15A

OUTPUT

Rated voltage 21.5 V (DC)

Rated current 2.4 A

Charging time approx. 60 min

Protection class II / (double insulation)

* BATTERY AND CHARGER ARE NOT INCLUDED

Noise and vibration data

Noise measurement value determined in accordance

with EN 60745. The A-rated noise level of the

power tool is typically as follows:

Sound pressure level LpA = 72 dB (A)

Uncertainty K = 3 dB

Sound power level LWA = 83 dB (A)

Uncertainty K = 3 dB

Wear ear muﬀs!

Total vibration value of the handle ah < 2.5 m/s2

Uncertainty K = 1.5 m/s2

Symbols on the appliance

Always wear safety goggles.

Always wear a mask.

NOTE

► The vibration emission value given in these

instructions has been measured in accord-

ance with a standardised test procedure and

can be used for comparison of the power

tool with another tool.

► The speciﬁed vibration emission value can

also be used to make an initial exposure

estimate.

WARNING!

► The vibration emission value may diﬀer from

the stated value during actual use of the

power tool, depending on of the manner in

which the power tool is being used.

► Try to keep the vibration loads as low as

possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the

working time. Wherein all states of operation

must be included (e.g. times when the power

tool is switched oﬀ and times where the power

tool is switched on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future

reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

PFSA 20-Li A1

■ 4 │ GB│IE│NI

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e)

When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD re-

duces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b)

Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁnger on the

switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving

parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

PFSA 20-Li A1 GB│IE│NI │ 5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that

cannot be controlled with the switch is danger-

ous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may aﬀect

the power tool’s operation. If damaged, have

the power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits,

etc., in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

5. Use and handling of the cordless

electrical power tool

a) Charge a rechargeable battery unit using

only the charger recommended by the

manu facturer. Chargers are often designed

for a particular type of rechargeable battery

unit. There is the danger of ﬁre if other types of

rechargeable battery units are used.

b) Only the rechargeable battery units supplied

are to be used with an electrical power tool.

The use of other rechargeable battery units may

lead to the danger of injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from paper-

clips, coins, keys, nails, screws or other small

metal objects that could cause the contacts to

be bridged.

Short-circuiting the contacts of a rechargeable

battery unit may result in heat damage or ﬁre.

d) Fluids may leak out of rechargeable battery

units if they are misused. If this happens,

avoid contact with the ﬂuid. If contact occurs,

ﬂush the aﬀected area with water. Seek

additional medical help if any of the ﬂuid

gets into your eyes. Escaping battery ﬂuid may

cause skin irritation or burns.

CAUTION! RISK OF EXPLOSION!

Never charge non-rechargeable

batteries.

Protect the rechargea-

ble battery from heat (including continuous

exposure to sunlight), ﬁre, water and mois-

ture. There is a risk of explosion.

6. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

PFSA 20-Li A1

■ 6 │ GB│IE│NI

Additional safety instructions

for paint spray guns

■Keep your work area clean, well lit and

free of paint and solvents, cloths and other

inﬂammable materials. Possible risk of sponta-

neous combustion. Have a fully functioning ﬁre

extinguisher available at all times.

■Ensure adequate ventilation in the spray area

and suﬃcient fresh air in the entire room.

Evaporation of ﬂammable solvents will cause an

explosive environment.

■Do not spray or clean with materials whose

ignition point is lower than 21°C. Use water-

based materials, non-volatile hydrocarbons

or similar materials. The evaporation of volatile

solvents will cause an explosive environment.

■Do not spray near ignition sources such as

static electric sparks, open ﬂames, ignition

ﬂames, hot items, motors, cigarettes or sparks

caused by plugging in/unplugging power

cables or by operating switches. These ignition

sources could ignite a ﬁre in the environment.

■Do not spray any material if you do not know

whether it is potentially dangerous. Unknown

materials can cause hazardous conditions.

■Wear additional personal protective equip-

ment such as suitable gloves and a protective

mask/respirator when spraying or when hand-

ling chemicals. Wearing appropriate protective

equipment for the conditions reduces your

exposure to dangerous substances.

■Be aware of the potential hazards of the

sprayed material. Note the markings on the

container and the manufacturer's information

on the spray material you are using, including

the instructions to use personal protective

equipment. Follow the manufacturer's

instructions to reduce the risk of ﬁre and injuries

caused by poisons, carcinogens, etc.

■ The spray gun must not be used for spraying

ﬂammable substances. Do not clean spray guns

with ﬂammable solvents.

WARNING!

► Pay attention to the dangers that can be

caused by the sprayed substance and also

observe the labels on the containers or the

instructions given by the manufacturer of the

substance.

Original accessories/auxiliary

equipment

■ Only use the accessories and additional

equipment that are speciﬁed in the operating

instructions and are compatible with the

appliance.

WARNING!

■ Do not use any accessories that are not

recommended by PARKSIDE. This can lead to

electric shock and ﬁre.

PFSA 20-Li A1 GB│IE│NI │ 7 ■

Safety guidelines for battery

chargers

■ This appliance may be used by

children aged 8 years and above

and by persons with limited

physical, sensory or mental

capabilities or lack of experience

and knowledge, provided that

they are under supervision or

have been told how to use the

appliance safely and are aware

of the potential risks. Do not al-

low children to use the appliance

as a plaything. Cleaning and

user maintenance tasks may not

be carried out by children unless

they are supervised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their

customer service department or

a similarly qualiﬁed person.

The charger is suitable

for indoor use only.

ATTENTION!

♦ This charger can only charge the following

batteries: PAP 20 A1/PAP 20 A2/

PAP20A3/PAP20B1/PAP20B3.

♦ A current list of battery compatibility can

be found at www.Lidl.de/Akku.

Working procedures

Viscosity

This appliance can process spray materials up to

max. 70DIN/sec (viscosity). You can determine

the viscosity (thickness) of the substance with the

supplied measuring cup using a simpliﬁed

measuring procedure.

♦ Fill the supplied measuring cup to the brim

with the spray material.

♦ Remove the measuring cup from the spray

material and allow the liquid to run out.

♦ Measure the time (in seconds) until the stream

of liquid stops. This time is called "DIN seconds

(DIN/sec)".

♦ If the value is too high, gradually thin the spray

material by adding small amounts of a suitable

thinning agent and mixing the liquid.

♦ Measure the DIN seconds again. Repeat the

process until you measure a viscosity of less

than 70 DIN/sec.

NOTE

► Do not exceed the maximal viscosity of the

appliance. The spray material must not be

too thick. Otherwise, the appliance might

clog.

► Ensure that the spray material and thinning

agent are compatible. Using an unsuitable

thinning agent may cause clots that clog

the appliance. Never mix synthetic resin

varnishes with cellulose thinners.

► To ﬁnd out which thinning agent is suitable

for your spray material (water, paint thinner),

refer to the manufacturer's notes provided

with the spray material.

► Granular products and products containing

solids must not be sprayed. Their abrasive

eﬀect shortens the service life of the

appliance.

PFSA 20-Li A1

■ 8 │ GB│IE│NI

Preparing the spray surface

♦ Cover the area around the spray area thoroughly

and over a wide area. Any surface that is not

masked could become contaminated.

♦ Make sure that the spray surface is clean, dry

and free of grease.

♦ Polished surfaces should be lightly sanded and

the sanding dust removed.

Before use

Charge battery pack (see ﬁg. B)

CAUTION!

► Always unplug the appliance before you

remove the battery pack from or connect it

to the charger.

NOTE

► Never charge the battery pack at an ambient

temperature of below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level must be

checked regularly. The optimum charge level

is between 50% and 80%. The storage

climate should be cool and dry and the

ambient temperature should be between 0°C

and 50°C.

♦ Insert the battery pack into the high-speed

charger .

♦ Insert the power plug into the socket. The red

control LED lights up to indicate that the

appliance is charging.

♦ The green LED indicates that the charging

process is complete and the battery pack

is ready.

♦ Push the battery pack into the appliance.

Attaching/disconnecting the battery

pack to/from the appliance

Attaching the battery pack

♦ Push the battery pack into the handle until

it clicks into place.

Removing the battery pack

♦ Press the release button and remove the

battery pack .

Checking the battery charge level

♦ Press the battery charge level button to

check the charge level of the battery. The status

is indicated in the adjacent battery display LED

as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Setting up

Assembly/disassembly

♦ Move the ▸ mark on the spray unit to the

mark on the motor unit . Now, turn the spray

unit until the ▸ mark on the spray unit

locks into the mark on the motor unit .

♦ Release the catch

5a

. Turn the ▸ mark on

the spray unit to the mark on the motor

unit to separate the two units.

Selecting/changing the nozzle

Nozzle Use

1.8 mm nozzle all types of paints and

lacquers

2.6 mm nozzle viscous spray material

♦ Undo the union nut completely and remove

it from the spray unit .

♦ Fit the desired nozzle onto the nozzle

head .

♦ Screw the union nut back onto the spray

unit .

PFSA 20-Li A1 GB│IE│NI │ 9 ■

Filling with spray material

♦ Unscrew the paint cup from the spray unit .

♦ To work on a horizontal object, place the riser

pipe in front, facing the nozzle head . To

work overhead, place the riser pipe at the

back, facing the motor unit .

♦ Fill the paint cup with the spray material and

screw it ﬁrmly onto the spray unit .

Switching the appliance on/oﬀ

Working methods

♦ Hold the spray gun at a constant distance from

the object. The ideal spraying distance is

approx. 15 cm.

♦ Work out the best settings by carrying out a

test.

♦ Do not switch the appliance on/oﬀ over the

spray surface. Rather, start/end the spraying

process approx. 10 cm from the spray surface.

Switching on

♦ To switch on, pull the trigger and keep it

pressed in.

Switching oﬀ

♦ To stop spraying, simply release the trigger .

Adjust spray pattern

Set the spray rate

♦ Turn the spray volume adjusting wheel to the

desired position:

♦ (–) = minimum spray rate

♦ (+) = maximum spray rate

NOTE

► We recommend starting at the minimum

setting.

Selecting a jet type

♦ Undo the union nut .

♦ Turn the protruding parts of the nozzle head

so that they point to the desired symbol on the

spray unit .

The appliance has the following settings:

▯ round jet

vertical ﬂat jet

horizontal ﬂat jet

♦ Re-tighten the union nut .

Maintenance and cleaning

WARNING! RISK OF INJURY! Always

switch the appliance oﬀ and remove

the battery before carrying out any

work on the appliance.

ATTENTION!

► Never immerse the paint spray gun completely

in solvent.

NOTE

► Thorough cleaning after every use is very

important for safety and operation.

Otherwise, the needle could get blocked and

proper operation of the appliance cannot be

guaranteed.

■ Wear suitable gloves when cleaning.

■ After every use, squirt water through the

appliance.

♦ To clean the spray unit , nozzle head ,

nozzles and the spray holes inside, use

the supplied cleaning brush , cleaning

needle or a cloth. Never use petrol, solvents

or cleansers which can damage plastic.

♦ Store the device only in dry interior rooms.

PFSA 20-Li A1

■ 10 │ GB│IE│NI

Cleaning/replacing the air ﬁlter

Check the air ﬁlter regularly , otherwise

malfunctions may occur.

♦ Remove the screws from the air ﬁlter

cover .

♦ Remove the air ﬁlter cover .

♦ Remove the air ﬁlter and examine it for

contamination.

♦ If necessary, shake out the air ﬁlter and

clean it under running water. Leave the air

ﬁlter to dry.

NOTE

► If necessary, replace the air ﬁlter with the

replacement air ﬁlter .

♦ Proceed in reverse order in order to reassemble

the appliance.

Disposal

The packaging is made from environ-

mentally friendly material which can

be disposed of at your local recycling

plant.

Do not dispose of power tools in

your normal household waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in an environ-

mentally compatible manner.

Do not dispose of batteries in

your normal household waste!

Defective or worn-out rechargeable

batteries must be recycled according

to Directive 2006/66/EC. Take

the battery pack and/or appliance to a nearby

collection facility.

Please consult your local authorities regarding

suitable disposal of worn-out power tools/battery

packs.

Dispose of the packaging in an envi-

ronmentally friendly manner.

Note the labelling on the packaging

and separate the packaging material

components for disposal if necessary. The packaging

material is labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information

on how to dispose of the worn-out

product.

Environmental compatibility and material

disposal:

■ Paints and lacquers… are considered hazardous

waste and must be disposed of accordingly.

■ Observe the local regulations.

■ Observe the manufacturer's instructions.

■ Environmentally harmful chemicals must not be

allowed to get into the ground, groundwater or

any body of water.

■ Spraying work next to bodies of water or

adjoining surfaces thereof (catchment area) is

therefore not permitted.

■ When buying paints, lacquers… pay attention

to their environmental compatibility.

PFSA 20-Li A1 GB│IE│NI │ 11 ■

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

X 12 V and X 20 V Team Series battery packs

come with a 3-year warranty valid from the date of

purchase.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating instruc-

tions for the product regarding proper use of the

product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

PFSA 20-Li A1

■ 12 │ GB│IE│NI

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(e.g.IAN12345) available as proof of

purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free

of charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and information

about what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to the Lidl

service page (www.lidl-service.com) where you

can open your operating instructions by entering

the item number (IAN) 354661_2010.

WARNING!

►Have the power tool repaired by the Service

Centre or a qualiﬁed technician and only

using genuine replacement parts. This will

ensure that the safety of the appliance is

maintained.

NOTE

► Replacement parts not listed (such as the

needle, nozzles, paint cup) can be ordered

via our service hotline.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: kom[email protected]

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (oﬀ peak))

E-Mail: kom[email protected]

IAN 354661_2010

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PFSA 20-Li A1 GB│IE│NI │ 13 ■

Original Declaration of Conformity

We, KOMPERNASS HANDELS GMBH, document oﬃcer: Mr Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, GERMANY, hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EC Low Voltage Directive

(2014/35/EU, charger only)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the

declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament

and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic

appliances.

Applied harmonised standards

EN 60745-1:2009/A11:2010

EN 50580:2012/A1:2013

EN 55014-1:2017

EN 55014-2:2015

EN 60335-1:2012/A13:2017

EN 60335-2-29:2004/A2:2010

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Type designation of machine: Cordless paint spray gun PFSA 20-Li A1

Year of manufacture: 12–2020

Serial number: IAN 354661_2010

Bochum, 10/12/2020

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical changes in the sense of further product development.

PFSA 20-Li A1

■ 14 │ GB│IE│NI

Ordering a replacement battery

If you want to order a replacement battery for your appliance, you can do so easily via the Internet on

www.kompernass.com or by telephone.

Due to limited stocks, this item may sell out in a relatively short time.

NOTE

► Online ordering of replacement parts might not be possible in some countries. In this case, please

contact the Service hotline.

Telephone ordering

Service Great Britain Tel.: 0800 404 7657

Service Ireland Tel.: 1890 930 034 (0,08 EUR/Min., peak · 0,06 EUR/Min., oﬀ peak)

To ensure a fast processing of your order, have the article number of your appliance to hand

(e.g. IAN 354661) in case of questions. The article number can be found on the type plate or

the title page of these instructions.

PFSA 20-Li A1 DK │ 15 ■

Indholdsfortegnelse

Indledning ............................................................16

Forskriftsmæssig anvendelse ...........................................................16

Udstyr ............................................................................16

Pakkens indhold ....................................................................16

Tekniske data ......................................................................16

Generelle sikkerheds anvisninger for elværktøjer ...........................17

1. Sikkerhed på arbejdspladsen .......................................................18

2. Elektrisk sikkerhed ................................................................18

3. Personsikkerhed ..................................................................18

4. Anvendelse og håndtering af elværktøjet ..............................................19

5. Anvendelse og håndtering af batteridrevet værktøj .......................................19

6. Service .........................................................................20

Supplerende sikkerhedsanvisninger til malerpistoler ........................20

Originalt tilbehør/ekstraudstyr .........................................................20

Sikkerhedsanvisninger for opladere .....................................................21

Arbejdsanvisninger ....................................................21

Viskositet ..........................................................................21

Forberedelse af sprøjteﬂaden ..........................................................22

Før ibrugtagning ....................................................... 22

Opladning af batteripakken (se ﬁg. B) ...................................................22

Indsætning/udtagning af batteripakken ..................................................22

Kontrol af batteriets tilstand ...........................................................22

Ibrugtagning ..........................................................22

Montering/afmontering ..............................................................22

Valg/udskiftning af dyse .............................................................22

Påfyldning af sprøjtemedie ............................................................23

Tænd/sluk for produktet ..............................................................23

Indstilling af sprøjtebillede ............................................................23

Indstilling af stråletypen ..............................................................23

Vedligeholdelse og rengøring ............................................ 23

Rengøring/udskiftning af luftﬁlteret .....................................................24

Bortskaﬀelse ..........................................................24

Garanti for Kompernass Handels GmbH ...................................25

Service ............................................................... 26

Importør .............................................................26

Oversættelse af den originale overensstemmelseserklæring ..................27

Bestilling af reservebatteri ..............................................28

Telefonisk bestilling ..................................................................28

La page charge ...

Parkside PFSA 20-Li A1 Mode d'emploi

Parkside PFSA 20-Li A1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents