Küppersbusch FK2545.0i Manuel utilisateur

BEDIENUNGSANWEISUNG

mit Montageanweisungen

INSTRUCTIONS FOR USE

and installation

Lesen Sie unbedingt die Gebrauchsanleitung

und den Montageplan vor Aufstellung,

Installation sowie Inbetriebnahme.

Please read the users and installation

instructions carefully before installation

of the appliance and before starting to use it.

Service und Kundendienst

Telefon: 0209 – 401 631

Email: [email protected]

EN DE ES PT FR IT NL EL PL TR

FK2545.0i

Please read this user manual first!

Dear Customer,

We hope that your product, which has been produced in modern plants and

checked under the most meticulous quality control procedures, will provide you

an effective service.

Therefore, read this entire user manual carefully before using the product and

keep it as a reference. If you handover the product to someone else, give the user

manual as well.

The user manual will help you use the product in a fast and safe way.

• Read the manual before installing and operating the product.

• Make sure you read the safety instructions.

• Keep the manual in an easily accessible place as you may need it later.

• Read the other documents given with the product.

Remember that this user manual is also applicable for several other models.

Differences between models will be identified in the manual.

Explanation of symbols

Throughout this user manual the following symbols are used:

CImportant information or useful tips.

AWarning against dangerous conditions for life and property.

BWarning against electric voltage.

A

C

SUPPLIER’S NAME MODEL IDENTIFIER (*)

INFORMATION

C

The model information as stored in the product data base

can be reached by entering following website and searching

for your model identiﬁer (*) found on energy label.

https://eprel.ec.europa.eu/

EN

5

1 Your refrigerator 6

2 Safety and environment

instructions 7

General safety ...................................7

HC warning ......................................8

For models with water dispenser ......9

Intended use .....................................9

Child safety ........................................9

Compliance with WEEE Directive and

Disposing of the Waste Product .........9

Compliance with RoHS Directive .......9

Package information ........................10

3 Installation 11

Points to be paid attention to when the

relocation of the refrigerator .............11

Before you start the refrigerator, .......11

Changing the illumination lamp .......12

Disposing of the packaging .............12

Disposing of your old refrigerator .....12

Placing and Installation ....................12

Reversing the doors ........................13

4 Preparation 14

5 Using your refrigerator 15

Thermostat setting button................15

Cooling ............................................15

Freezing ...........................................16

Defrost ............................................16

Stopping your product .....................17

6 Maintenance and cleaning 18

Protection of plastic surfaces ..........18

7 Troubleshooting 19

CONTENTS

6EN

C Figures that take place in this instruction manual are schematic and may not

correspond exactly with your product. If the subject parts are not included in the

product you have purchased, then it is valid for other models.

1 Your refrigerator

1. Dairy compartment

2. Egg tray (1 pcs.)

3. Door shelves

4. Bottle shelf

5. Bottle gripper

6. Air grill

7. Crisper

8. Crisper cover

9. Defrost water collection channel -

Drain tube

10. Movable shelves

11. Interior light & Thermostat knob

12. a.) Freezing compartment & ice tray

(for models) b.) Frozen food

compartment & ice tray (for

models)

11

10

8

7

9

12

64

1

2

3

5

*

EN

7

This section provides the safety

instructions necessary to prevent the

risk of injury and material damage.

Failure to observe these instructions will

invalidate all types of product warranty.

Intended use

A

WARNING:

Keep ventilation openings,

in the appliance enclosure or

in the built-instructure, clear

of obstruction.

A

WARNING:

Do not use mechanical

devices or other means

to accelerate the defrosting

process, other than those

recommended by the

manufacturer.

A

WARNING:

Do not damage the

refrigerant circuit.

A

WARNING:

Do not use electrical

appliances inside the food

storage compartments of the

appliance, unless they are of

the type recommended by

the manufacturer.

This appliance is intended to be used

in household and similar applications

such as

– staff kitchen areas in shops, offices

and other working environments;

– farm houses and by clients in hotels,

motels and other residential type

environments;

– bed and breakfast type environments;

– catering and similar non-retail

applications.

General safety

• This product should not be used

by persons with physical, sensory

and mental disabilities, without

sufficient knowledge and experience

or by children. The device can only

be used by such persons under

supervision and instruction of a

person responsible for their safety.

Children should not be allowed to

play with this device.

• In case of malfunction, unplug the

device.

• After unplugging, wait at least 5

minutes before plugging in again.

• Unplug the product when not in use.

• Do not touch the plug with wet

hands! Do not pull the cable to plug

off, always hold the plug.

• Do not plug in the refrigerator if the

socket is loose.

• Unplug the product during

installation, maintenance, cleaning

and repair.

• If the product will not be used for

a while, unplug the product and

remove any food inside.

• Do not use the product when the

compartment with circuit cards

located on the upper back part of

the product (electrical card box

cover) (1) is open.

2 Safety and environment instructions

8EN

1

• Do not use steam or steamed

cleaning materials for cleaning

the refrigerator and melting the

ice inside. Steam may contact the

electrified areas and cause short

circuit or electric shock!

• Do not wash the product by

spraying or pouring water on it!

Danger of electric shock!

• In case of malfunction, do not use

the product, as it may cause electric

shock. Contact the authorised

service before doing anything.

• Plug the product into an earthed

socket. Earthing must be done by a

qualified electrician.

• If the product has LED type lighting,

contact the authorised service for

replacing or in case of any problem.

• Do not touch frozen food with wet

hands! It may adhere to your hands!

• Do not place liquids in bottles and

cans into the freezer compartment.

They may explode.

• Place liquids in upright position after

tightly closing the lid.

• Do not spray flammable substances

near the product, as it may burn or

explode.

• Do not keep flammable materials

and products with flammable gas

(sprays, etc.) in the refrigerator.

• Do not place containers holding

liquids on top of the product.

Splashing water on an electrified

part may cause electric shock and

risk of fire.

• Exposing the product to rain,

snow, sunlight and wind will cause

electrical danger. When relocating

the product, do not pull by holding

the door handle. The handle may

come off.

• Take care to avoid trapping any part

of your hands or body in any of the

moving parts inside the product.

• Do not step or lean on the door,

drawers and similar parts of the

refrigerator. This will cause the

product to fall down and cause

damage to the parts.

• Take care not to trap the power

cable.

HC warning

If the product comprises a cooling

system using R600a gas, take care

to avoid damaging the cooling system

and its pipe while using and moving the

product. This gas is flammable. If the

cooling system is damaged, keep the

product away from sources of fire and

ventilate the room immediately.

C

The label on the inner left

side indicates the type of gas

used in the product.

EN

9

For models with water

dispenser

• Pressure for cold water inlet shall

be maximum 90 psi (620 kPa). If

your water pressure exceeds 80 psi

(550 kPa), use a pressure limiting

valve in your mains system. If you

do not know how to check your

water pressure, ask for the help of a

professional plumber.

• If there is risk of water hammer

effect in your installation, always

use a water hammer prevention

equipment in your installation.

Consult Professional plumbers if you

are not sure that there is no water

hammer effect in your installation.

• Do not install on the hot water inlet.

Take precautions against of the

risk of freezing of the hoses. Water

temperature operating interval shall

be 33°F (0.6°C) minimum and

100°F (38°C) maximum.

• Use drinking water only.

Intended use

• This product is designed for

home use. It is not intended for

commercial use.

• The product should be used to store

food and beverages only.

• Do not keep sensitive products

requiring controlled temperatures

(vaccines, heat sensitive medication,

medical supplies, etc.) in the

refrigerator.

• The manufacturer assumes no

responsibility for any damage due to

misuse or mishandling.

• Original spare parts will be provided

for 10 years, following the product

purchasing date.

Child safety

• Keep packaging materials out of

children’s reach.

• Do not allow the children to play

with the product.

• If the product’s door comprises a

lock, keep the key out of children’s

reach.

Compliance with WEEE

Directive and Disposing of

the Waste Product

This product complies with

EU WEEE Directive (2012/19/EU). This

product bears a classification symbol

for waste electrical and electronic

equipment (WEEE).

This product has been

manufactured with high

quality parts and materials

which can be reused and

are suitable for recycling.

Do not dispose of the

waste product with normal

domestic and other wastes at the end

of its service life. Take it to the collection

center for the recycling of electrical and

electronic equipment. Please consult

your local authorities to learn about

these collection centers.

Compliance with RoHS

Directive

• This product complies with EU WEEE

Directive (2011/65/EU). It does

not contain harmful and prohibited

materials specified in the Directive.

10 EN

Package information

Packaging materials of the product

are manufactured from recyclable

materials in accordance with our

National Environment Regulations. Do

not dispose of the packaging materials

together with the domestic or other

wastes. Take them to the packaging

material collection points designated

by the local authorities.

EN

11

3 Installation

B In case the information which are

given in the user manual are not

taken into account, manufacturer will

not assume any liability for this.

Points to be paid attention

to when the relocation of the

refrigerator

1. Your refrigerator should be

unplugged.Before transportation of

your refrigerator, it should be emptied

and cleaned.

2. Before it is re-packaged, shelves,

accessories, crisper, etc. inside your

refrigerator should be fixed with

adhesive tape and secured against

impacts. Package should be bound

with a thick tape or sound ropes

and the transportation rules on the

package should be strictly observed.

3. Original packaging and foam

materials should be kept for future

transportations or moving.

Before you start the

refrigerator,

Check the following before you start

to use your refrigerator:

1. Attach 2 plastic wedges as illustrated

below. Plastic wedges are intended

to keep the distance which will ensure

the air circulation between your

refrigerator and the wall. (The picture

is drawn up as a representation and it

is not identical with your product.)

2. Clean the interior of the refrigerator as

recommended in the “Maintenance

and cleaning” section.

3. Connect the plug of the refrigerator

to the wall socket. When the fridge

door is opened, fridge internal lamp

will turn on.

4. When the compressor starts to

operate, a sound will be heard. The

liquid and gases sealed within the

refrigeration system may also give rise

to noise, even if the compressor is

not running and this is quite normal.

5. Front edges of the refrigerator may

feel warm. This is normal. These

areas are designed to be warm to

avoid condensation.

Electrical connection

Connect your product to a grounded

socket which is being protected by a

fuse with the appropriate capacity.

Important:

The connection must be in compliance

with national regulations.

• The power plug must be easily

accessible after installation.

• Electrical safety of your refrigerator

shall be guaranteed only if the earth

system in your house complies with

standards.

• The voltage stated on the label

located at left inner side of your

product should be equal to your

network voltage.

• Extension cables and multi plugs

must not be used for connection.

12 EN

B A damaged power cable must be

replaced by a qualified electrician.

B Product must not be operated before

it is repaired! There is the risk of electric

shock!

Disposing of the packaging

The packing materials may be

dangerous for children. Keep the packing

materials out of the reach of children or

dispose of them by classifying them in

accordance with the waste instructions

stated by your local authorities. Do not

throw away with regular house waste,

throw away on packaging pick up spots

designated by the local authorities.

The packing of your refrigerator is

produced from recyclable materials.

Disposing of your old

refrigerator

Dispose of your old refrigerator without

giving any harm to the environment.

• You may consult your authorized

dealer or waste collection center of

your municipality about the disposal of

your refrigerator.

Before disposing of your refrigerator,

cut out the electric plug and, if there

are any locks on the door, make them

inoperable in order to protect children

against any danger.

Placing and Installation

A If the entrance door of the room

where the refrigerator will be installed is

not wide enough for the refrigerator to

pass through, then call the authorized

service to have them remove the doors

of your refrigerator and pass it sideways

through the door.

1. Install your refrigerator to a place that

allows ease of use.

2. Keep your refrigerator away from heat

sources, humid places and direct

sunlight.

3. There must be appropriate air

ventilation around your refrigerator

in order to achieve an efficient

operation. If the refrigerator is to be

placed in a recess in the wall, there

must be at least 5 cm distance with

the ceiling and at least 5 cm with the

wall. Do not place your product on

the materials such as rug or carpet.

4. Place your refrigerator on an even

floor surface to prevent jolts.

Changing the illumination

lamp

To change the Bulb/LED used for

illumination of your refrigerator, call your

AuthorisedService.

The lamp(s) used in this appliance

is not suitable for household room

illumination. The intended purpose of

this lamp is to assist the user to place

foodstuffs in the refrigerator/freezer in

a safe and comfortable way.The lamps

used in this appliance have to withstand

extreme physical conditions such as

temperatures below -20 °C.

(only chest and upright freezer)

CThis product is equipped with a

lighting source of the "G" energy class.

The lighting source in this product

shall only be replaced by professional

repairers.

EN

13

Reversing the doors

3

5

2

1

6

4

D

B

A

C

7

11

10

9

8

E

F

G

14 EN

4 Preparation

• Your refrigerator should be installed at

least 30 cm away from heat sources

such as hobs, ovens, central heater

and stoves and at least 5 cm away

from electrical ovens and should not

be located under direct sunlight.

• The ambient temperature of the room

where you install your refrigerator

should at least be 10°C. Operating

your refrigerator under cooler

conditions is not recommended with

regard to its efficiency.

• Please make sure that the interior

of your refrigerator is cleaned

thoroughly.

• If two refrigerators are to be installed

side by side, there should be at least

2 cm distance between them.

• When you operate your refrigerator

for the first time, please observe the

following instructions during the initial

six hours.

• The door should not be opened

frequently.

• It must be operated empty without

any food in it.

• Do not unplug your refrigerator. If

a power failure occurs out of your

control, please see the warnings in

the “Recommended solutions for the

problems” section.

• Original packaging and foam

materials should be kept for future

transportations or moving.

EN

15

5 Using your refrigerator

Thermostat setting button

The operating temperature is regulated

by the temperature control.

Warm Cold

1 2 3 4 5

(Or) Min. Max.

1 = Lowest cooling setting

(Warmest setting)

5 = Highest cooling setting

(Coldest setting)

(Or)

Min. = Lowest cooling setting

(Warmest setting)

Max. = Highest cooling setting

(Coldest setting)

The average temperature inside the

fridge should be around +5°C.

Please choose the setting according

to the desired temperature.

Please note that there will be different

temperatures in the cooling area.

The coldest region is immediately

above the vegetable compartment.

The interior temperature also depends

on ambient temperature, the frequency

with which the door is opened and the

amount of foods kept inside.

Frequently opening the door causes

the interior temperature to rise.

For this reason, it is recommended

to close the door again as soon as

possible after use.

The interior temperature of your

refrigerator changes for the following

reasons;

• Seasonal temperatures,

• Frequent opening of the door and

leaving the door open for long

periods,

• Food put into the refrigerator

without cooling down to the room

temperature,

• The location of the refrigerator in the

room (e.g. exposing to sunlight).

• You may adjust the varying interior

temperature due to such reasons

by using the thermostat. Numbers

around the thermostat button

indicates the cooling degrees.

• If the ambient temperature is higher

than 32°C, turn the thermostat

button to maximum position.

• If the ambient temperature is lower

than 25°C, turn the thermostat

button to minimum position.

Cooling

Food storage

The fridge compartment is for the

short-term storage of fresh food and

drinks.

16 EN

Freezing

Freezing food

The freezing compartment is marked

with this symbol.

You can use the appliance for freezing

fresh food as well as for storing pre-

frozen food.

Please refer to the recommendations

given on the packaging of your food.

Storing frozen food

The frozen food compartment is

marked with symbol.

The frozen food compartment is

suitable for the storage of pre-frozen

food. The recommendation for storage,

as stated on the food packaging,

should be observed at all times.

Defrost

A) Fridge compartment

Fridge compartment performs full-

automatic defrosting. Water drops and

a frosting up to 7-8 mm can occur

on the inner rear wall of the fridge

compartment while your refrigerator

cools down. Such formation is normal

as a result of the cooling system.

The frost formation is defrosted by

performing automatic defrosting with

certain intervals thanks to the automatic

defrosting system of the rear wall. User

is not required to scrape the frost or

remove the water drops.

Water resulting from the defrosting

passes from the water collection groove

and flows into the evaporator through

the drain pipe and evaporates here by

itself.

Check regularly to see if the drain

pipe is clogged or not and clear it with

the stick in the hole when necessary.

Deep freezer compartment does not

perform automatic defrosting in order

to prevent decaying of the frozen food.

EN

17

Stopping your product

If your thermostat is equipped with

“0” position:

- Your product will stop operating

when you turn the thermostat button to

“0” (zero) position. Your product will not

start unless to you turn the thermostat

button to position “1” or one of the

other positions again.

If your thermostat is equipped with

“min” position:

- Unplug your product to stop it.

B) Freezer compartment

Defrosting is very straightforward

and without mess, thanks to a special

defrost collection basin.

Defrost twice a year or when a frost

layer of around 7 (1/4”) mm has formed.

To start the defrosting procedure,

switch off the appliance at the socket

outlet and pull out the mains plug.

All food should be wrapped in several

layers of newspaper and stored in a

cool place (e.g. fridge or larder).

Containers of warm water may be

placed carefully in the freezer to speed

up the defrosting.

Do not use pointed or sharp-edged

objects, such as knives or forks to

remove the frost.

Never use hair dryers, electrical

heaters or other such electrical

appliances for defrosting.

Sponge out the defrost water

collected in the bottom of the freezer

compartment. After defrosting, dry the

interior thoroughly.

Insert the plug into the wall socket and

switch on the electricity supply.

18 EN

6 Maintenance and cleaning

A Never use gasoline, benzene or

similar substances for cleaning

purposes.

B We recommend that you unplug the

appliance before cleaning.

B Never use any sharp abrasive

instrument, soap, household

cleaner, detergent and wax polish for

cleaning.

C Use lukewarm water to clean the

cabinet of your refrigerator and wipe it

dry.

C Use a damp cloth wrung out in

a solution of one teaspoon of

bicarbonate of soda to one pint of

water to clean the interior and wipe it

dry.

B Make sure that no water enters the

lamp housing and other electrical

items.

B If your refrigerator is not going to be

used for a long period of time, unplug

the power cable, remove all food,

clean it and leave the door ajar.

C Check door seals regularly to ensure

they are clean and free from food

particles.

A To remove door racks, remove all the

contents and then simply push the

door rack upwards from the base.

ANever use cleaning agents or water

that contain chlorine to clean the

outer surfaces and chromium coated

parts of the product. Chlorine causes

corrosion on such metal surfaces.

Protection of plastic

surfaces

C Do not put the liquid oils or oil-cooked

meals in your refrigerator in unsealed

containers as they damage the

plastic surfaces of your refrigerator. In

case of spilling or smearing oil on the

plastic surfaces, clean and rinse the

relevant part of the surface at once

with warm water.

EN

19

7 Troubleshooting

Please review this list before calling the service. It will save your time and

money. This list includes frequent complaints that are not arising from defective

workmanship or material usage. Some of the features described here may not

exist in your product.

The refrigerator does not operate.

• The plug is not inserted into the socket correctly. >>>Insert the plug into the

socket securely.

• The fuse of the socket which your refrigerator is connected to or the main fuse

have blown out. >>>Check the fuse.

Condensation on the side wall of the fridge compartment (MULTIZONE, COOL

CONTROL and FLEXI ZONE).

• Ambient is very cold. >>>Do not install the refrigerator in places where the

temperature falls below 10 °C.

• Door has been opened frequently. >>>Do not open and close the door of

refrigerator frequently.

• Ambient is very humid. >>>Do not install your refrigerator into highly humid

places.

• Food containing liquid is stored in open containers. >>>Do not store food with

liquid content in open containers.

• Door of the refrigerator is left ajar. >>>Close the door of the refrigerator.

• Thermostat is set to a very cold level. >>>Set the thermostat to a suitable level.

• Compressor is not running

• Protective thermic of the compressor will blow out during sudden power

failures or plug-out plug-ins as the refrigerant pressure in the cooling system

of the refrigerator has not been balanced yet. The refrigerator will start running

approximately after 6 minutes. Please call the service if the refrigerator does not

startup at the end of this period.

• The fridge is in defrost cycle. >>>This is normal for a full-automatically defrosting

refrigerator. Defrosting cycle occurs periodically.

• The refrigerator is not plugged into the socket. >>>Make sure that the plug is fit

into the socket.

• Temperature settings are not made correctly. >>>Select the suitable temperature

value.

• There is a power outage. >>>Refrigerator returns to normal operation when the

power restores.

The operation noise increases when the refrigerator is running.

20 EN

• The operating performance of the refrigerator may change due to the changes in

the ambient temperature. It is normal and not a fault.

The refrigerator is running frequently or for a long time.

• New product may be wider than the previous one. Larger refrigerators operate

for a longer period of time.

• The room temperature may be high. >>>It is normal that the product operates

for longer periods in hot ambient.

• The refrigerator might be plugged in recently or might be loaded with food.

>>>When the refrigerator is plugged in or loaded with food recently, it will take

longer for it to attain the set temperature. This is normal.

• Large amounts of hot food might be put in the refrigerator recently. >>>Do not

put hot food into the refrigerator.

• Doors might be opened frequently or left ajar for a long time. >>>The warm air

that has entered into the refrigerator causes the refrigerator to run for longer

periods. Do not open the doors frequently.

• Freezer or fridge compartment door might be left ajar. >>>Check if the doors are

closed completely.

• The refrigerator is adjusted to a very low temperature. >>>Adjust the refrigerator

temperature to a warmer degree and wait until the temperature is achieved.

• Door seal of the fridge or freezer may be soiled, worn out, broken or not

properly seated. >>>Clean or replace the seal. Damaged/broken seal causes

the refrigerator to run for a longer period of time in order to maintain the current

temperature.

Freezer temperature is very low while the fridge temperature is sufficient.

• The freezer temperature is adjusted to a very low value. >>>Adjust the freezer

temperature to a warmer degree and check.

Fridge temperature is very low while the freezer temperature is sufficient.

• The fridge temperature is adjusted to a very low value. >>>Adjust the fridge

temperature to a warmer degree and check.

Food kept in the fridge compartment drawers is frozen.

• The fridge temperature is adjusted to a very high value. >>>Adjust the fridge

temperature to a lower value and check.

Temperature in the fridge or freezer is very high.

EN

21

• The fridge temperature is adjusted to a very high value. >>>Fridge compartment

temperature setting has an effect on the temperature of the freezer. Change the

temperatures of the fridge or freezer and wait until the relevant compartments

attain a sufficient temperature.

• Doors are opened frequently or left ajar for a long time. >>>Do not open the

doors frequently.

• Door is ajar. >>>Close the door completely.

• The refrigerator is plugged in or loaded with food recently. >>>This is normal.

When the refrigerator is plugged in or loaded with food recently, it will take longer

for it to attain the set temperature.

• Large amounts of hot food might be put in the refrigerator recently. >>>Do not

put hot food into the refrigerator.

• Vibrations or noise.

• The floor is not level or stable. >>> If the refrigerator rocks when moved slowly,

balance it by adjusting its feet. Also make sure that the floor is strong enough to

carry the refrigerator, and level.

• The items put onto the refrigerator may cause noise. >>>Remove the items on

top of the refrigerator.

There are noises coming from the refrigerator like liquid flowing, spraying, etc.

• Liquid and gas flows occur in accordance with the operating principles of your

refrigerator. It is normal and not a fault.

Whistle comes from the refrigerator.

• Fans are used in order to cool the refrigerator. It is normal and not a fault.

Condensation on the inner walls of refrigerator.

• Hot and humid weather increases icing and condensation. It is normal and not a

fault.

• Doors are opened frequently or left ajar for a long time. >>>Do not open the

doors frequently. Close them if they are open.

• Door is ajar. >>>Close the door completely.

Humidity occurs on the outside of the refrigerator or between the doors.

• There might be humidity in the air; this is quite normal in humid weather. When

the humidity is less, condensation will disappear.

Bad odour inside the refrigerator.

22 EN

• No regular cleaning is performed. >>>Clean the inside of the refrigerator regularly

with a sponge, lukewarm water or carbonate dissolved in water.

• Some containers or package materials may cause the smell. >>>Use a different

container or different brand packaging material.

• Food is put into the refrigerator in uncovered containers. >>>Keep the food in

closed containers. Microorganisms spreading out from uncovered containers

can cause unpleasant odours.

• Remove the foods that have expired best before dates and spoiled from the

refrigerator.

The door is not closing.

• Food packages are preventing the door from closing. >>>Replace the packages

that are obstructing the door.

• The refrigerator is not completely even on the floor. >>>Adjust the feet to

balance the refrigerator.

• The floor is not level or strong. >>>Make sure that the floor is level and capable

to carry the refrigerator.

Crispers are stuck.

• The food is touching the ceiling of the drawer. >>>Rearrange food in the drawer.

If The Surface Of The Product Is Hot.

• High temperatures may be observed between the two doors, on the side panels

and at the rear grill while the product is operating. This is normal and does not

require service maintenance!Be careful when touching these areas.

La page charge ...

Küppersbusch FK2545.0i Manuel utilisateur

Küppersbusch FK2545.0i Manuel utilisateur

dans d''autres langues

Autres documents