Lumination LRX Series LED Luminaire EMBB Guide d'installation

Taper
Guide d'installation
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 1 of 5
(Rev 05/19/23)
IND342-Lumination-LRX-Series-LED-Luminaire-EMBB-New-Construction-Installation-Guide_R01
Installation Guide
IND342
Lumination® LED Luminaire
EMBB New Construction
(LRX Series)
BEFORE YOU BEGIN / AVANT DE COMMENCER
Read these instructions and IOTA ILB-CP instruction manual completely and carefully.
Wear work gloves to prevent dirt and oil from being transferred to the luminaire.
IMPORTANT SAFEGUARDS / MESURES DE SÉCURITÉ IMPORTANTES
Turn power o before inspection, installation or removal.
Properly ground electrical enclosure.
To prevent electrical shock, do not mate unit connector until
installation is complete and AC power is supplied to the unit.
This kit provides more than one power supply output source.
To reduce the risk of electrical shock, disconnect both normal
and emergency sources by turning o the AC branch circuit
and by disconnecting the unit connector.
Battery is a sealed unit. Components are not replaceable.
Replace the entire unit when necessary.
Installation and servicing should be performed by qualied
personnel only. De-energize before opening.
The kit is for use with grounded LED luminaires listed to UL
standards. Not for use in heated air outlets or hazardous
locations.
The kit requires an unswitched AC power source of 120 to 277
volts, 50/60Hz.
Do not mount near gas or electric heaters.
The use of accessory equipment not recommended by
manufacturer may cause unsafe condition.
The kit should be mounted in locations and at heights where
it will not readily be subjected to tampering by unauthorized
personnel.
The kit and frame will supply output listed as below for 90
minutes.
For use in 0°C minimum, 40°C maximum ambient
temperature.
Do not use this equipment for other than intended use.
Install in accordance with the National Electrical Code and
local regulations.
Lighting xture manufacturers, electricians, and endusers
need to ensure product system compatibility before nal
installation
Couper l’alimentation avant l’inspection, l’installation ou d’eectuer de la maintenance
Eectuer une mise à la terre adéquate du boitier électrique.
Pour prévenir les chocs électriques, ne pas connecter le connecteur de l’unité de
la batterie avant que l’installation ne soit complétée et que le CA ne soit fourni au
luminaire.
Cette trousse fournie plus d’une source de sortie d’alimentation. Pour réduire les
risques d’électrocution, déconnecter toutes les sources de courant en débranchant le
CA de la dérivation et aussi en déconnectant le connecteur de l’unité.
La batterie est une unité scellée dont les composantes ne sont pas remplaçables.
Remplacer l’unité entière lorsque nécessaire.
L’installation et la maintenance doivent être eectuée par du personnel qualié
seulement. Couper la tension avant de procéder.
Cette trousse a été conçue pour être utilisé avec des luminaires DEL possédant une
mise à la terre et listés sous un standard UL. Ne pas utiliser pour un usage dans un
conduit d’air chaud ou dans des emplacements dangereux.
Cette trousse requière une source d’alimentation en CA de 120 à 277 volts sans
interrupteur à 50/60Hz.
L’utilisation d’équipement accessoire non recommandé par le manufacturier peut
causer des conditions dangereuses.
Cette trousse devrait être installée dans un emplacement adéquat et à une hauteur
appropriée dans le but d’empêcher toute manipulation non autorisée.
Cette trousse et ce châssis fourniront la source lumineuse répertoriée pour 90 minutes
Peut-être utilisé à une température ambiante entre 0°C minimum et 40°C maximum.
Ne pas utiliser cet équipement pour autre chose que pour l’utilisation prévue.
Installer en conformité avec le code électrique national et la réglementation locale
Les fabricants d’appareils d’éclairage, les électriciens et les utilisateurs naux doivent
s’assurer de la compatibilité du produit avant l’installation nale.
CAUTION / ATTENTION
Follow all NEC and local codes.
Use only UL approved wire for input/output connections.
Minimum size 18AWG copper wire or 14AWG for
continuous runs.
Suivre tous les codes NEC ainsi que les codes locaux.
Utiliser seulement du câblage approuvé par UL pour les connections d’entrées et
de sorties. Utiliser des conducteurs de cuivre de grosseur 18AWG minimum ou de
grosseur 14AWG dans le cas de montage en rangée continue.
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 2 of 5
(Rev 05/19/23)
IND342-Lumination-LRX-Series-LED-Luminaire-EMBB-New-Construction-Installation-Guide_R01
Lumination® (LRX - Series) Installation Guide
Kit vs Fixture
LRXR EMBB Fixture LRXR EMBB Frame Kit LRXS EMBB Fixture LRXS EMBB Frame Kit
SAP Description SAP Description SAP Description SAP Description
LRXR610ABBCCEL FRAME6REL07 LRXS610ABBCCEL FRAME6SEL07
LRXR618ABBCCEL FRAME6REL10 LRXS618ABBCCEL FRAME6SEL10
LRXR618ABBCCEL FRAME6REL10 LRXS618ABBCCEL FRAME6SEL10
LRXR810ABBCCEL FRAME8REL07 LRXS810ABBCCEL FRAME8SEL07
LRXR818ABBCCEL FRAME8REL10 LRXS818ABBCCEL FRAME8SEL10
LRXR830ABBCCEL FRAME8REL10 LRXS830ABBCCEL FRAME8SEL10
LRXR840ABBCCEL LRXS840ABBCCEL
Nomenclature for LRX Series:
I - “A” Denotes color rendering index (CRI)
8 - 80
9 - 90
II - “BB” Denotes correlated color temperature (CCT)
27 - 2700K
30 - 3000K
35 - 3500K
40 - 4000K
50 - 5000K
Provided Item Qty.
1 LRX EMBB Frame Kit 1
2 LRX EMBB Fixture 1
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• The luminaire must be supplied with 120-277 VAC,
50/60 Hz (In 120-277V application).
• Connected to an individual properly grounded branch
circuit, protected by a 15 or 20 ampere circuit breaker. Use
min. 75°C supply conductor.
Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance with National Electric
Code (NEC) Article 600 and local codes.
Fixture Requirements
LRXREL Fixture Thickness of Ceiling LRXSEL Fixture Thickness of Ceiling
SAP Description Max.(mm) SAP Description Max.(mm)
LRXR610ABBCCEL 15 LRXS610ABBCCEL 15
LRXR618ABBCCEL LRXS618ABBCCEL
LRXR618ABBCCEL
20
LRXS618ABBCCEL
20
LRXR810ABBCCEL LRXS810ABBCCEL
LRXR818ABBCCEL LRXS818ABBCCEL
LRXR830ABBCCEL LRXS830ABBCCEL
LRXR840ABBCCEL LRXS840ABBCCEL
III - “CC” Denotes dimming type
MD - 0-10V Dimming
PH - Phase cut Dimming
• FRAME6REL07, FRAME8REL07, FRAME6SEL07, FRAME8SEL07 shall be mounted height Max. 22.71 ft. (6.92m)
• FRAME6REL10, FRAME8REL10, FRAME6SEL10, FRAME8SEL10 shall be mounted height Max. 25.91 ft. (7.92m)
Thickness of ceiling is listed below:
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 3 of 5
(Rev 05/19/23)
IND342-Lumination-LRX-Series-LED-Luminaire-EMBB-New-Construction-Installation-Guide_R01
Lumination® (LRX - Series) Installation Guide
Fixture
Diameter
Hole
Diameter
RX6 5.9–6.5 in.
RX8 7.6–8.2 in. L-brackets
Mounting brackets
1
Cut the appropriate
size hole into ceiling
tile.
Frame Installation
Components
1
2 3 4 5
Provided Item Qty.
1 Frame (6-inch or 8-inch) 1
2 Mounting brackets 2
3 L-Bracket 2
4 U-Bracket (used only with RC Series Installs) 1
5 Wing nut 3
Fixture
Diameter
Hole
Diameter
RX6 5.9–6.5 in.
RX8 7.6–8.2 in.
L-brackets
Mounting brackets
2
Place side L-brackets on existing frame screws
and tighten with screwdriver on both sides of
the frame. Then attach mounting brackets to
both L-brackets with wing nuts (provided).
Fixture
Diameter
Hole
Diameter
RX6 5.9–6.5 in.
RX8 7.6–8.2 in.
L-brackets
Mounting brackets
3
Slide hanger bars through
adjustable mounting brackets.
Bars Conduit
A B
Adjust height and
tighten wing nut
4
Option A: Mount xture by attaching hanger bars
to T-Grid ceiling (BH3 SKU 94890).
Option B: Mount xture with ½” EMT conduit.
Note: Supplied by 3rd party
Bars Conduit
A B
Adjust height and
tighten wing nut
5
Adjust xture height to be ush with ceiling and
tighten both mounting bracket wing nuts.
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 4 of 5
(Rev 05/19/23)
IND342-Lumination-LRX-Series-LED-Luminaire-EMBB-New-Construction-Installation-Guide_R01
Lumination® (LRX - Series) Installation Guide
1
Ensure that the power to the unit is turned o. Use proper lockout and tagout procedures.
EMBB Installation
2
Secure the battery on the ceiling. Attach the test switch to the LRX EMBB xture. First remove the nut from the end
of test switch, then put test switch through the hole of xture, then thread nut to test switch.
Brown
Blue
Black
Unswitched Power (L1)
Common (N)
Switched Power (L2)
Grounding
Dimming (+)
Dimming (–)
Green
Violet
Gray
Connect male and female ends
of the battery unit connector
4
Connect AC and dimming leads in the junction box. Verify that AC supply line and dimming leads are connected properly.
• If dimming leads will not be utilized, please do not remove the wire connectors.
• For phase cut dimming product, dimming leads can be disconnected.
• Connect male and female ends of the battery unit connector. Then the battery will discharge. Please refer to the picture shown above.
• Wire diagram is shown above.
• Dimming compatibility for both 0-10V and phase cut, please refer to Current’s website: www.LED.com.
Brown
Blue
Black
Unswitched Power (L1)
Common (N)
Switched Power (L2)
Grounding
Dimming (+)
Dimming (–)
Green
Violet
Gray
Connect male and female ends
of the battery unit connector
Tighten nut on
inside of housing
Remove nut from
test switch
Attach to housing
Tighten nut on
inside of housing
Remove nut from
test switch
Attach to housing
Tighten nut on
inside of housing
Remove nut from
test switch
Attach to housing
Box closed
3
Secure the battery on the ceiling. Attach the test switch to the LRX EMBB xture. First remove the nut from the end
of test switch, then put test switch through the hole of xture, then thread nut to test switch.
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 5 of 5
(Rev 05/19/23)
IND342-Lumination-LRX-Series-LED-Luminaire-EMBB-New-Construction-Installation-Guide_R01
Lumination® (LRX - Series) Installation Guide
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A)/NMB-005(A)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
NOTE: For switchable product, please refer to the gure bellowing for operation. For 1000/650lm product, default output level is 1000lm.
Push switch up or left to activate 650lm. For 4000/3000lm, default output level is 4000lm.
Load springs into upright position by twisting the springs
upward and carefully insert the xture to the hole of the
frame. Ensure xture is secure.
• All kit and frame will be completely addressed on ceiling
5
Springs up
Lumens Setting Switch
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Lumination LRX Series LED Luminaire EMBB Guide d'installation

Taper
Guide d'installation