ALTA AP6-Pro Mode d'emploi

Marque: ALTA

Modèle: AP6-Pro

Catégorie: Commutateurs réseau

Taper: Mode d'emploi

QUICK START GUIDE

MODEL: AP6-Pro

Before You Begin

Download the Alta app on your mobile device,

and create your free Alta account.

You may also visit manage.alta.inc to manage

your Alta devices.

manage.alta.inc

Package Contents

AP6-Pro Mounting Plate Ceiling Mount

Anchors

(Qty. 2)

Wall-Mount

Screws (Qty. 2)

Ceiling Tile

Screws (Qty. 2)

T-Bar Screws Nuts Rubber Feet

Note: Be sure to use the included

mounting hardware for installation.

Installation Requirements

• Ethernet cabling (CAT 5 or above)

• 48V PoE+ switch or PoE injector

• Phillips screwdriver

• Drill and drill bit for wall or ceiling mounting

Hardware Overview

Front

LED

Logo Indicator

Logo Indicator If you need to remove the AP

from the mount, use a ﬂat blade screwdriver to

disengage the Mounting Plate here.

LED Illuminates white by default when AP is

online and functional. Can be changed to blue,

white, or off in the Alta app or management

interface. Flashes when booting.

Back

RESET

PoE

Ethernet Port

Reset Button

Reset Button Press down for 10 seconds until

the LED begins ﬂashing to reset the AP to

factory defaults.

Ethernet Port Connects to an Ethernet cable

from your PoE+ Switch. An optional 48V, 0.5A

adapter can be purchased and used to power

the AP.

Hardware Installation

Ceiling Tile Mount

1. Remove the appropriate ceiling tile.

2. Align the Mounting Plate in the desired

location ﬂat on the tile (typically centered).

Mark the areas indicated below for the

screws and the Ethernet cable.

3. Secure the Mounting Plate to the Ceiling

Mount with the ceiling tile between using

the two Ceiling Tile Screws and the two Nuts.

Assembled Top View Assembled Bottom View

Proceed to “Connecting The AP” on page 13

Wall Mount

1. Position the Mounting Plate in the desired

location and use a pencil to mark the holes.

2. If running cabling along the wall, remove the

notch on the AP.

RESET

PoE

3. Secure the Mounting Plate to the wall

using the Wall-Mount Screws and a Phillips

screwdriver. Be sure to use the screws

included with the product.

If mounting on drywall, use the anchors to

ensure secure mounting. Use a 6 mm drill

bit to drill the holes for the anchors and

insert them in the wall.

Note: Ensure the included Wall-Mount

Screws are ﬂush with Mounting Plate.

Proceed to “Connecting The AP” on page 13

T-Bar Ceiling TIle Mount

1. Use a small Phillips head screwdriver to

loosen the two pre-installed screws on the

Ceiling Mount to allow enough clearance for

the T-Bar.

2. Rotate the Ceiling Mount around the T-Bar.

3. Tighten both screws using a Phillips

screwdriver.

4. Connect the Mounting Plate to the Ceiling

Mount with the T-Bar Screws.

Proceed to “Connecting The AP” on page 13

Connecting The AP

The AP is powered over Ethernet, it can be

48V, 0.5A PoE Injector.

1. Connect an Ethernet cable from your PoE+

Switch (or optional PoE Injector).

2. Connect the other end to the Ethernet

Port on the AP. If mounting on the wall,

the Ethernet cable can be fed through the

removable notch area.

RESET

PoE

3. Align the AP with the Mounting Plate.

RESET

PoE

4. Slightly tilt the AP right and then left as you

slide the AP down the Mounting Plate to

lock it into place.

Set Up Your Device

1. Follow the instructions in the Alta app or

management interface to set up your AP.

1.0

bcb923123426

New AP

Home Base

Set Up

Disconnecting the AP

If you need to remove the AP from the mount,

use a ﬂat blade screwdriver to disengage the

Mounting Plate at the logo indicator.

Speciﬁcations

Model: AP6-Pro

Dimensions 190mm (7.5") x 125mm (4.9")

32mm (1.25")

Weight 0.4 kg (0.9 lbs)

Mount Material Ceiling/Wall: Polycarbonate

Drop Ceiling: Steel

Weatherprooﬁng IP54

Network Interface Ethernet, WiFi, Bluetooth

Management Interface (1) GbE RJ45 Port

Button(s) Reset/Factory Reset

LED Blue, White

Power Method PoE+

Power Supply

PoE+ Enabled Network Switch

48V, 0.5A PoE Adapter

(Optional)

Supported Voltage Range 42.5-57V DC

Max. Power Consumption 25W

Max. Transmit Power 2.4 GHz: 23 dBm @2NSS

5 GHz: 26 dBm @4NSS

MIMO 2.4 GHz: 2 x 2

5 GHz: 4 x 4

Throughput Rate 2.4 GHz: Up to 573 Mbps

5 GHz: Up to 5.8 Gbps

Mounting Wall, ceiling, drop-ceiling,

table top

Operating Temperature -30 to 60° C (-22 to 140° F)

Operating Humidity 5 to 95% Noncondensing

Certiﬁcations CE, FCC, IC

Compliance

Federal Communication Commission

Interference Statement

This product has been tested and found to comply with the

limits for a Class B digital device pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference

to radio communications. Operations of this equipment

in a residential area is likely to cause harmful interference

in which case the user will be required to correct the

interference at his own expense.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

FCC Caution

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired

operation.

This device is restricted to indoor use.

Non-Modiﬁcation Statement

Changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

FCC Radiation Statement

This equipment complies with FCC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance

20cm between the radiator and your body.

CAN ICES-003(B) / NMB-003(B)

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans

le présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

The device for operation in the band 5150-5250 MHz is

only for indoor use to reduce the potential for harmful

interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz

sont réservés uniquement pour une utilisation à l’intérieur

aﬁn de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux.

ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation

exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d’exposition

aux rayonnements IC établies pour un environnement

non contrôlé. Cet équipement doit être installé et utilisé

avec un minimum de 20cm de distance entre la source de

rayonnement et votre corps.

The transmitter module may not be co-located with any

other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un

autre émetteur ou antenne.

The Country Code Selection feature is disabled for products

marketed in the US/Canada.

For product available in the USA/Canada market, only

channel 1~11 can be operated. Selection of other channels is

not possible.

Pour les produits disponibles aux États-Unis / Canada du

marché, seul le canal 1 à 11 peuvent être exploités. Sélection

d’autres canaux n’est pas possible.

La page est en cours de chargement...

ALTA AP6-Pro Mode d'emploi

Marque: ALTA

Modèle: AP6-Pro

Catégorie: Commutateurs réseau

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: ALTA AP6-Pro User guide

ALTA AP6-Pro Mode d'emploi

ALTA AP6-Pro Mode d'emploi

dans d''autres langues

Autres documents