lamber P700-EK Manuel utilisateur

Marque: lamber

Modèle: P700-EK

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

REV.01-09/09/06

MANUALEISTRUZIONI

INSTRUCTIONSMANUAL

INSTALLATION-BEDIENUNG

INSTRUCTIONSD'EMPLOI

P550-ek

P700-ek

LAVA-OGGETTI

LAVE-BATTERIE

WAREWASHER

ZUBEHÖRE-SPÜLERE

DICHIARAZIONE DI CONFORMITA' - DECLARATION OF CONFORMITY

DECLARATION DE CONFORMITE' - KONFORMITÄTS ERKLÄRUNG

Noi - Nous soussignés - The following - Die Unterzeichnete Fa:

dichiariamo sotto la nostra esclusiva responsabilità che il prodotto

attestons sous notre entière responsabilité que le produit suivant

hereby declares under full responsability that the following product

erklärt unter eigener Verantwortung, dass folgende Produkte

LAVAOGGETTI - LAVE-BATTERIE - WARES-WASHER – ZUBEHÖRE-SPÜLER

mod. P550-ek/P700-ek

al quale questa dichiarazione si riferisce è conforme alle seguenti norme:

auquel se réfère cette déclaration, est conforme aux normes suivantes:

for which this declaration refers to the conformity of the following standards:

auf welche sich diese Erklärung bezieht, folgendem Standard entsprechen:

- EN 60335-1 (1994) + A11,A1,A12,A13,A14,A15

Sicurezza degli apparecchi elettrici d'uso domestico e similare. Norme generali

Safety of household and similar electrical appliances-General requirements.

- EN 60335-2-58 (1997)

Sicurezza degli apparecchi elettrici d'uso domestico e similare. Parte 2':Norme particolari lavastoviglie uso

collettivo.

Safety of household and similar electrical appliances-Part 2':Particular requirements for commercial electric

dishwashing machines.

- EN 292-2 (1992) Part 1' - PART 2'

Sicurezza del macchinario-Concetti fondamentali-Principi generali progettazione-Specifiche e principi tecnici.

Safety of machinery-Basic concepts-General principles for design-Tecnical principles an specification

- EN 61770- (2000)

Apparecchi elettrici connessi alla rete idrica. Disposizioni per evitare il ritorno d’acqua per effetto sifone e il

guasto dei complessi di raccordo

Electric appliances connected to the water mains. Avoidance of backsiphonage and failure of hose-sets

in base a quanto previsto dalle Direttive:

selon ce qui est prévu par les Directives:

on the basis of what is foreseen by the Directives:

aufgrund der vorgesehenen Richtilinien:

73/23/CEE, 89/392/CEE, 91/368CEE,92/31CEE, 93/44CEE, 93/68CEE

Decliniamo ogni responsabilità per sinistri a persone o a cose derivanti da manomissioni da parte di terzi o da carenze di manutenzione o riparazione.

Nous déclinons toute responsabilité pour sinistres à personnes ou à objets qui derivent de l'intervention de la part de tiers non specialistes ou de

carences de manutention ou reparation.

We decline any responsability for injuries or damage derived from machine misuse, abuse by others or improper machine maintenance or repairs.

Wir Iehnen jegliche Verantwortung für Schäden an Personen oder Dingen ab, die auf fehlerhaftes Eingreifen Dritter oder auf mängelhafte Wartung oder

Reparation zurückzuführen.

li 01/01/06

(data/date/Datum)

(name signature or equivalent of authorized representative)

- EMC -

Noi - Nous soussignés - The following - Die Unterzeichnete Fa:

LAMBER snc di Affaba F. e c.

Via Italia 6

26855 Lodivecchio (LO) ITALY

dichiariamo sotto la nostra esclusiva responsabilità che il prodotto

attestons sous notre entière responsabilité que le produit suivant

hereby declares under full responsability that the following product

erklärt unter eigener Verantwortung, dass folgende Produkte

LAVAOGGETTI - LAVE-BATTERIE - WARES-WASHER – ZUBEHÖRE-SPÜLER

mod. P550-ek/P700-ek

al quale questa dichiarazione si riferisce è conforme alle seguenti norme:

auquel se réfère cette déclaration, est conforme aux normes suivantes:

for which this declaration refers to the conformity of the following standards:

auf welche sich diese Erklärung bezieht, folgendem Standard entsprechen:

• Electromagnetic compatibility – Requirements for household appliances, electric tools and

similar apparatus – Part 1: Emission – Product family standard – EN 55014-1 (2000) + A1

(2001)

Compatibilità elettromagnetica – Prescrizioni per gli elettrodomestici, gli utensili elettrici e gli apparecchi similari –

Parte 1: Emissione Norma di famiglia di prodotti – EN 55014-1 (2000) + A1 (2001)

• Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current

emissions (equipment input current ≤ 16 A per phase) – EN 61000-3-2 (2000)

Compatibilità elettromagnetica (EMC) – Parte 3-2: Limiti – Limiti per le emissioni di corrente armonica

(apparecchiature con corrente di ingresso ≤ 16 A per fase) – EN 61000-3-2 (2000)

• Electromagnetic compatibility (EMC) – Part 3-3: Limits – Limitation of voltage fluctuations

and flicker in low-voltage supply systems for equipment with rated current ≤ 16 A – EN

61000-3-3 (1995) + A1 (2001)

Compatibilità elettromagnetica (EMC) – Parte 3-3: Limiti – Limitazione delle fluttuazioni di tensione e dei flicker in

sistemi di alimentazione in bassa tensione per apparecchiature con corrente nominale ≤ 16 A – EN 61000-3-3

(1995) + A1 (2001)

• Electromagnetic compatibility - Requirements for household appliances, electric tools and

similar apparatus - Part 2: Immunity - Product family standard - EN 55014-2 (1997) + A1

(2001)

Compatibilità elettromagnetica - Requisiti di immunità per apparecchi elettrodomestici, utensili e degli apparecchi

elettrici similari – Parte 2: Immunità – Norma di famiglia di prodotti- EN 55014-2 (1997) + A1 (2001)

in base a quanto previsto dalle Direttive:

selon ce qui est prévu par les Directives:

on the basis of what is foreseen by the Directives:

aufgrund der vorgesehenen Richtilinien: 89/336 CEE, 92/31 CEE, 93/68 CEE

li 01/06/06

(data/date/Datum)

(name signature or equivalent of authorized representative)

INDICE ITALIANO

Note generali pag 07

Introduzione e norme di sicurezza pag. 08

Parte prima - NORME PER L'UTILIZZATORE pag. 13

Pannello Comandi pag. 14

Funzionamento ed uso; detersivi; manutenzione; inconvenienti possibili pag. 15

Parte seconda - NORME PER L'INSTALLATORE pag. 31

Schema allacciamenti pag. 32

Collegamento elettrico, scarico; alimentazione idrica pag. 33

Schema regolazioni pag. 41

Schema collegamenti pag. 42

Schema elettrico pag. 43

Dati tecnici pag. 46

SOMMAIRE FRANÇAIS

Remarque générales pag. 07

Introduction et normes de securité pag. 09

Première partie - INSTRUCTIONS POUR L'UTILISATEUR pag. 13

Emploi controles pag. 14

Fonctionnement et emploi, detersifs, entretien, inconvenients pag. 19

Deuxième partie - Instructions pour l'installateur: pag. 31

Installation pag. 32

Branchement hydraulique, vidange, branchement electrique pag. 35

Schema regulations pag. 41

Schema branchements pag. 42

Schema electrique pag. 43

Données tecniques pag. 46

CONTENTS ENGLISH

Introduction and safety notes pag. 07

General notes pag. 10

First section - FOR THE USER pag. 13

Control panel pag. 14

Working and use, cleansing agents, maintenance, possible troubles pag. 23

Second section - FOR THE INSTALLER pag. 31

Installation pag. 32

Water drain, water connections, electrical connections pag. 37

Regulations scheme pag. 41

Connections scheme pag. 42

Wiring diagram pag. 43

Specifications pag. 46

INDEX DEUTSCH

Allgemeines pag. 07

Einführung und Sichereitsnormen pag. 11

Teil 1 - FÜR DEN BENUTZER pag. 13

Steuertafel pag. 14

Arbeitsweise und Anwendung, Reinigungsmittel, Wartung, Mögliche Störungen pag. 27

Teil 2 - FÜR DEN INSTALLATEUR pag. 31

Installationsblatt pag. pag. 32

Wasserablauf, Wasserversorgung,Elektrischer Anschluß, pag. 39

Eichung pag. 41

Anschlußschema pag. pag. 42

Schaltschema pag. 43

Technische Daten pag. 46

NOTE GENERALI ITALIANO

Vi ringraziamo per la scelta da Voi fatta nell'acquisto della Vostra LAVA-OGGETTI

Il perfetto funzionamento della macchina e risultati di lavaggio ottimali sotto il profilo igienico sanitario

potranno essere garantiti solo se tutte le avvertenze del presente Manuale verranno rispettate.

Ci auguriamo che le informazioni contenute nel presente manuale Vi siano di aiuto. Esse sono basate sui

dati e sulla nostra attuale migliore conoscenza.

Leggete attentamente quanto riportato nel manuale, comprese le raccomandazioni ed i suggerimenti.

Leggete anche le condizioni di garanzia.

REMARQUES GENERALES FRANÇAIS

Nous Vous remercions de Votre choix lors de l'achat de votre LAVE-BATTERIE

Le fonctionnement parfait de l'appareil et les résultats de lavage optimaux sous le profil hygiénique

sanitaire,peuvent seulement être garantis si tous les avertissements dans ce manuel-ci sont respectés.

Nous souhaitons que les renseignements contenus dans ce manuel vous soient utiles. Ils sont basés sur les

donneés et sur notre meilleure connaissance actuelle.

Lisez attentivement ce qui est énancé dans le manuel, y compris les recommandations et les suggestions.

Lisez aussi les conditions de vente, y compris celles qui limitent la garantie.

GENERAL NORMS ENGLISH

Thank You for purchasing our WARES-WASHER Machine.

Perfect washing-up results as far as hygiene concerns and a correct operation of the dishwashing machine

can be assured only in case the instructions reported in the present manual are carefully followed.

We hope the information reported in the present manual will be helpful to You.

They are based on data and our best updated knowledge.

Carefully read the Instructions reported in the manual, recommendations and suggestions included.

Carefully read the terms of sale too, the ones limiting warranty included.

ALLGEMEINES DEUTSCH

Wir danken Ihnen, daß Sie unsere ZUBEHÖRE-SPÜLER gewählt haben.

Der perfekte Betrieb und die optimalen Reinigungsergebnisse können nur garantiert werden, wenn alle

Anweisungen beachtet werden.

Wir hoffen, daß die in vorliegendem Gebrauchshandbuch enthaltenen Informationen Ihnen hilfreich sein

werden. Die Angaben beruhen auf unserem aktuellen Kenntnisstand.

Lesen Sie bitte aufmerksam das vorliegende Gebrauchshandbuch sowie die darin enthaltenen

Empfehlungen und Hinweise. Lesen Sie bitte ebenfalls die Verkaufsbedingungen sowie die Konditionen, die

die Garantieleistungen regeln.

INTRODUCTION ENGLISH

AND SAFETY NOTES

INTRODUCTION

- The machine is an Industrial Wares-washing machine .

- The machine is in conformity to the European Norms 89/336/CEE for the radio noises.

- According to EEC directive no.23 of 19/02/1973 and the law of actuation no.791 of 18/10/1987, our

appliances are built-up according to the good technique notes in force in Italy and abroad.

- Noise level of the machine, less than 70 dB(A).

PRELIMINARY OBSERVATION

Carefully read the instructions reported in the present user manual, as it gives important indications about

safety of installation, operation and maintenance:

- carefully keep the present manual for further consultations;

- the illustrations and drawings showing the machine are intended for general reference only and are

not necessarily accurate in every instance;

- the dimensions and characteristics of the machine, given in this Manual, are not to be considered

binding and may be changed without prior notice;

- having removed the packing material, check that all the equipment is present. If there is any doubt,

do not use it and contact qualified personnel. The packing elements (plastic bags, nails, etc.) should

be kept away from children, because they are dangerous.

GENERAL SAFETY REGULATIONS

THIS SAFETY CODE HAS BEEN COMPILED IN YOUR INTEREST. Strict adherence to these rules will

reduce the risks of injury both to yourself and to others;

Personnel working with this machine must adhere strictly to all statutory safety regulations as well as the

specific rules listed below. Failure to do so may result in personal inyury and damage to the machine;

- DO NOT attempt to move, install, set-up or operate this machine until you have read and fully

understood this Manual. If doubt persists, ask your supervisor;

- never leave tools, parts or other loose material on or in the machine;

- Before switching the equipment the equipment on, make sure that the model plate data conforms to

that of the electrical and water distribution network;

- remember that even with the mains indicator in the “OFF” position, the incoming cables are still live;

- BEFORE starting the machine or the cycle, after any maintenance or repair work, make sure all

protective are correctly installed;

- be vigilant at all times, remember that your safety and that of your fellow workers depends on you;

- when moving or lifting the machine, care must be taken to comply with all the relevant regulations

governing such operations;

- installation should be carried out by qualified personnel according to the manufacturer's instructions.

- this equipment should be destined to the use which it has been conceived for. Any other application

should be considered improper and consequently dangerous;

- the equipment should only be used by personnel trained for its use;

SPECIAL SAFETY REGULATIONS

- adjustement and repairs must be carried out only by personnel qualified. Repair carried out by

unskilled personnel may be dangerous;

- perfect washing-up results as far as hygiene concerns and a correct operation of the washing machine

can be assured only in case the instructions reported in the present handbook are carefully followed;

- the machine must be only used by authorized personnel which must comply with sanitary measures;

- do not leave the machine in an environment with temperatures lower than to 0°C;

- the machine protection degree is IP21, therefore it should not be washed with direct high pressure jets

of water;

Entrata acqua 3/4"

Entrée de 'eau 3/4"

Water inlet 3/4"

Wasseranschluss 3/4"

Lavaggio superiore rotante in acciaio inox

Lavage supérieur rotatif en acier inoxydable

Stainless steel Upper rotating washing

Rotierend Oberer Wascharm aus CNS

Lavaggio inferiore rotante in acciaio inox

Lavage inférieur rotatif en acier inoxydable

Stainless steel Lower rotating washing

Rotierender Unterer Wascharm aus CNS

Filtri vasca in acciaio inox

Filtres cuve en acier inoxydable

Stainless steel Tank filters

Herausnehmbare Schmutzauffangfilter über dem Waschtank

Filtro aspirazione pompa in acciaio inox

Filtre aspiration pompe en acier inoxydable

Stainless steel Suction pump filter

Pumpenansaugfilter aus Inox

Doppia parete coibentata 20mm

Double paroi isolée 20mm

Double skin with insulation 20mm

Doppelwandige Isolation 20 mm

Doppia parete coibentata 14m

Double paroi isolée 14mm

Double skin with insulation 14mm

Doppelwandige Isolation 14mm

Vasca a "sedia" con fondo inclinato e spigoli arrotondati

Cuve inclinée avec angles arrondis

Tank with slanting bottom

Waschtank mit Gefälle komplett abgerundet

Pompa autosvuotante

Pompe autovidangeable

Autodraining washing pump

Pumpenmotor

Dosatore additivo di risciacquo

Doseur de produit pour rinçage

Rinse-aid dispenser

Nachspülmitteldosiergerät

Telaio,vasca e capot in acciaio inossidabile

Châssis, cuve et capot en acier inoxydable

Body,tank and Top in Stainless steel construction

Gehäuserahmen und Verblendungen aus Inox

Boiler coibentato in acciaio inox

Surchauffeur isolé en acier inox

Stainless steel Boiler with insulation

Isolierter Boiler aus CNS

Risciacquo inferiore rotante in acciaio inox (cono 90°)

Rinçage inférieur rotatif en acier inoxydable (cône 90°)

Stainless steel Lower rotating rinsing (cone 90°)

Rotierender Unteres Spülsystem aus CNS (Konus 90°)

Risciacquo superiore rotante in acciaio inox (cono 90°)

Rinçage supérieur rotatif en acier inoxydable (cône 90°)

Stainless steel Upper rotating rinsing ( cone 90°)

Rotierendes Oberes Spülsystem aus CNS (Konus 90°)

Troppopieno

Trop-plein

Overflow

Überlaufrohr

Scarico vasca ø 32mm

Vidange cuve ø 32mm

Water outlet ø 32mm

Ablauf ø 32mm

Fate conoscenza con l'apparecchio

Learn to use the appliance

Faites connaissance avec l'appareil

Wollen Sie den Apparat kennenlernen

NORME PER L'UTENTE

INSTRUCTIONS POUR L'UTILISATEUR

INSTRUCTIONS FOR THE USER

AUFSTELLUNGSANLEITUNG

FÜR DEN BENUTZER

OPTIONAL

Dis.1

PANNELLO COMANDI EMPLOI CONTROLES

CONTROL PANEL STEUERTAFEL

Pulsante ciclo

Bouton cycle

Cycle pushbutton

Programmdrucktaste

Lampada porta aperta

Lampe indicatrice de porte ouverte

Door opening lamp

Türkontrollampe

Lampada ciclo

Lampe indicatrice de cycle

Cycle lamp

Programmkontrollampe

Lampada temperatura

Lampe température

Température lampe

Temperaturlampe

Pulsante pompa scarico

Bouton pompe de vidange

Drain pump pushbutton

Taste für Ablaufpumpe

Pulsante selezione tempo lavaggio

Bouton sélecteur temps de lavage

Wash time selection pushbutton

Programmwahlschalter

Termometri temperatura di lavaggio e risciacquo

Thermomètre témperature de lavage et rinçage

Wash and rinse thermometer

Wasch-und Nachspültemperaturthermometer

Interruttore generale

Interrupteur général

Main switch

Hauptschalter

ENGLISH

First Section - FOR THE USER

WORKING AND USE

NOTE:

- When the objects to be washed present burnt crusts, or a long time is elapsed from cooking up to the

time of washing, it is necessary to make a previous softening in water at 50°C, by using an appropriate

softeningproducts;

- Never deep naked hands in detergent water;

- While the machine is running, never open the door too rapidly;

- Only use specific anti-frothing detergents.

OPERATION BEFORE WASHING

BEFORE STARTING THE WORKING OPERATION BE

SURE THAT:

- the cock is open;

- the filters and the overflow are in

their housings;

- the wash arm and the rinse arm are free to

pivot;

- brightener and washing powder dispenser

containers are loaded.

THEN PROCEED:

A - Put the detergent directly into the tank, by

paying attention to distribute it uniformly

on the filters, the quantity being according to

supplier's instructions.

N.B. When using chlorinated detergent, it is

suggested to use an automatic dispenser; if

otherwise, brownish spots might appear on the

surfaces, because of chlorine reactions, if

powering the detergent directly in the tank.

B - Place the objects in the basket minding to

previously remove all solid waste and fat.

N.B.: When the objects to be washed present

burnt crusts, or a long time is elapsed from

cooking up tothe time of washing, it is necessary

to make a previous softening in water at 50°C,

by using an appropriate softening product.

C - Turn the machines on by wall switch and

push the switch “A” situated in Dis.1.

At this moment the thermometer display lights up

And the tank fills up. When the tank is full the

control lamp for cycle “2” lights up.

D – Introduce the basket in the ware-washer.

The control lamp “E” will flash in case the door of

the dishwasher is open.

Before you start the cycle be sure that the control

lamp “D” is flashing. This means that the water for

the washing cycle and the rinsing water

temperature reached the ideal temperature for

working.

E – Choose the washing period cycle and push

the button “B” between the following items:

- lamp 1 flashing – short cycle of 2 minutes

- lamp 2 flashing – medium cycle 3 minutes

- lamps 1 and 2 lightening at the same time

long cycle of 4 minutes.

The washing period cycle has to be chosen

regarding the dirt that has to be removed.

F – Close the door of the ware-washer.

Push the button cycle “C”

The dishwasher starts the washing with the

period you chosen. Additional to this period will

be a pause of 5 seconds and a rinsing period of

23 seconds with clean water about 85° to 90°C.

The control cycle lamp is flashing up to the end of

the complete washing period. Finished the

washing period the control lamps will stop

lightening.

It is possible to interrupt the washing cycle at any

time simply pushing again button “B”.

The lighting of the control lamp “D” means that

the water reached the needed temperature of 85°

to 90°C.

The rinsing will start working of by the reached

temperature need. That means the period of the

washing cycle you chosed will be extended up to

having reached the exact temperature

(thermocontrol).

G - Take away the basket .

In order to make washing keep on, load

another basket and press pushbutton "C". The

cycle will automatically start again.

- Endless cycle (maximum 15 minutes) : the

door being closed and the cycle put on (any

cycle), keep the button “B” pressed for 3

seconds: lamps 1 and 2 will flash at the same

time (thermocontrol excluded); the cycle can be

interrupted at any time pressing again button “C”

that will let final sequences start.

- Self-washing cycle : Remove the overflow

from the tank and close the warewasher door

while the machine is on (time 10 minutes).

DURING WASHING

1) When the machine is running never

change wash time selector position.

2) Only use specific anti-frothing detergents

3) Deactivate the equipment in case of fault

or malfunction. For repairs, only address to a

technical assistance center authorised by the

manufacturer and impose the use of original

spare parts.

If these conditions are not met, the equipment

safety could be jeopardised.

ACHIEVEMENTS

Any deficiency in the washing process is

apparent when dirty residuals are visible. Any

halos might be caused by an insufficient rinsing:

in this case, check that the rinsing jets are clean

and there is a sufficient pressure in the water

distribution network.

In the case that residuals are present, check

that:

• the washing jets are clean

• there is detergent

• the pump suction filter is clean

• the positions of the objects in the rack are

correct.

CLEANSING AGENTS

Choice of the suitable cleansing agent is an

essential condition if you want to obtain

extremely good washing results as concerns

hygienic results. It is then important to consider

some points. First of all only highly alkaline and

chlorine-active antifoam products, especially

made for industrial dish-washing machines,

must be used and they must be produced by

well known reliable Firms. Mean concentration

of the cleansing agents in powder must be 1,5-

2,5 g/lt. Mean concentration of liquid cleansing

agents nust be 2-4 g/lt.

In order to avoid scales and corrosions, put

cleansing agent above water level on the

nearest area of the sucking pump filter, in this

way it will immediately dilute and will not deposit

on the tank bottom.

DRAIN PUMP INSTRUCTIONS

(only for machines with drain pump)

The drain pump works automatically only

during the washing cycle to discharge the

exceeding water coming from the rinsing cycle.

At the end of the working day, in order to

completely discharge the tank, it is necessary

to perform the following operations:

1. Open the hood of the dishwasher

2. Remove the overflow pipe from the tank;

3 . Afterwards push button “F” for 3 seconds.

Control lamp “E” and the cycle lamp (the last

chosen) are flashing alternatively.

The discharge will stop automatically after 5

minutes. Control lamps will stop flashing.

Reinstall the overflow and shut the hood.

RINSING ADDITIVES

To grant a perfect rinsing, a quick drying and to

avoid calcareous sediments on glasses and

cups you must add a surfactant on water

(Brightner).

Your cleansing agent supplier's will be able to

suggest the most suitable product. Your

machine is equipped with a rinse-aid dispenser.

Mean concentration used is 0,15 g/lt.

DESCALING

When hard water is used you can find, inside

the machine and also on dishes, calcareous

sediments which must be removed both for

hygienic and operating reasons by a descaling

operation.

Operating process and frequency of this

intervention are suggested by your cleansing

agent supplier who has suitable products,

generally containing phosphoric acid.

In order to avoid damage to the machine do not

increase the quantities and once operations end

rinse abundantly.

CLEANING AND PREVENTIVE

MAINTENANCE

PRECAUTION AND CLEANING

INSTRUCTIONS

- IMPORTANT : Before carrying out the

cleaning and maintenance operations,

disconnect the equipment from the mains

power supply:

- high temperatures can be reached inside

the machine (90°C). After the power supply

has been removed, wait until the machine

has reached room temperature, before

working on it.

- the machine protection degree is IP21,

therefore it should not be washed with

direct high pressure jets of water;

- never leave tools, parts or other loose

material on in or on the machine;

- BEFORE starting machine or cycle, after

any maintenance or repair work, make sure

all protectives are correctly installed;

DAILY MAINTENANCE

- Disconnect the machine with pushbutton

"A";

- Lift the overflow pipe and let the water

drain out of the tank;

- Wash thoroughly the tank and the filters

housing to remove all impurities;

- Take the filters out and clean them under

running water;

- Re-assemble the overflow pipe and the

filters in their housings;

- Check and clean the washing and the

rinsing jets;

- Clean the outer surface of the machine by

using a wet sponge; do not use water jets

because, beside being dangerous they

could damage the electrical parts; do not

use abrasive detergents;

- When the machine is to remain idle for a

long time, drain all the water from the

boiler and from the electropump.

Also leave the door open.

NEVER WASH THE EXTERNAL PART OF

THE MACHINE WITH A WATER JET

POSSIBLE TROUBLES - CAUSES - SOLUTIONS

PROBLEMS CAUSES SOLUTIONS

The machine doesn't catch Main switch is switched off; Turn ON the main switch;

The water doesn't go in Water cock closed; Open water cock;

The Overflow is not in place; Reassemble the Overflow in

place;

Insufficient Washing Wrong detergent or dosage Use anti-foam detergent in the

insufficient; right dosage and never with

cold water;

Low temperature in the tank; Wait untill the water gets hot;

Dirty wash filter; Clean filter;

Insufficient Rinsing Rinsing nozzles blocked; Unscrew and clean nozzles

under running water;

Hydraulic pressure lower than Wait untill the pressure is on or

1 bar - 100 kPa; buy a booster pump;

CAUTION! FOR ANY OTHER TROUBLE, CALL SERVICE

SANIFICATION

At last each 30 days it would be useful to do this operation which guarantees the complete hygienic

conditions of the machine. We suggest to contact your cleansing agent supplier who will give you quantity

and name of the most suitable product you can use and that, generally, is an active chloride powder (100-

200 ppm).

In order to avoid damage to the machine do not increase the quantities and once operations end, rinse

abundantly.

USEFUL HINTS OF STAINLESS STEEL MAINTENANCE

Stainless steel is so called because it is not affected by oxidation,this is due to a thin molecular layer of

oxide on the surface which protects againts further oxidation. There are, howevwr, substances which can

modify or destroy this layer,giving rise to corrosion:besides preventing the protective film of oxide from

reforming,these substances corrode the stainless steel itself and can cause irreparable damage. It is

therefore necessary to prevent this by choosing correct cleaning products and by complying with the

following simple recommendations:never forget that when using these appliances,the first and

fundamental rule is to guarantee that the cleaning products are both non-toxic and hygienic.

Before using any detergent to clean either the stainless steel or the immediate and sorrounding floor area,

always ask your supplier for the most suitable product which does not cause corrosion on the steel itself; the

onset of rust is most commonly caused by the use of unsuitable cleaning materials (strongly acid chlorate

based detergents) or on inadequate maintenance.

Our appliances are made of stainless steel AISI 304 (18-10 type) for exterior panelling,upper tops,tanks etc.

Comply with the following instructions when cleaning and servicing parts in stainless steel.

Ordinary daily maintenance

Carefully and frequently clean the surfaces using a damp cloth; use soap and water or normal detergents,so

long as these do not contain abrasives or chlorine based substances such as sodium hypochlorite

(bleech),hydrochloric acid or other such solutions:These products quickly and irreparably corrode stainless

steel. When cleaning floors underneath or near the appliances, never use the above mentioned products as

vapours or splashes could subject the steel to similar destructive effects.

Only ever rub in the direction of the satining, then thoroughly rinse with clean water and carefully dry.

Rust : water supply pipes, inevitably convey particles of rust dissolved in the water especially in new

installation plants or when taps are opened after a period of inactivity. These iron deposits must not be

allowed to remain on the stainless steel since they produce rust by contamination.

Use suitable products to remove any rust marks,from companies which produce detergents for industrial

use. After application, thoroughly rinse with clean water, neutralizing the action of the product with an

alkaline detergent normally used to clean such appliances or with another specific product.

DO NOT USE METAL MATS TO CLEAN THE STAINLESS STEEL

NORME PER L’INSTALLATORE

Le istruzioni che seguono sono rivolte a personale qualificato, il solo

autorizzato ad attuare le verifiche e le eventuali riparazioni.

La Ditta declina ogni responsabilità nel caso di interventi effettuati da

personale non qualificato e/o utilizzo di ricambi non originali.

INSTRUCTIONS POUR L'INSTALLATEUR

Les instructions suivantes sont adressées à un personnel qualifié, qui est le

seul autorisé à effectuer les vérifications et les réparations éventuelles.

Le constructeur décline toute responsabilité en cas d'interventions effectuées

par du personnel non qualifié.

INSTRUCTIONS FOR THE INSTALLER

The following instructions are addressed to a qualified personnel, the only one

authorised to carry-out checks and repair, if any.

The Manufacturer declines any responsibility in the case of interventions

made by a non qualified personnel.

AUFSTELLUNGSANLEITUNG

FÜR DEN INSTALLATEUR

Die folgenden Hinweise sind an das Fachpersonal gerichtet; nur das

Fachpersonal darf Prüfungen und eventuelle Reparaturen durchführen.

Unsere Firma ist von jeglicher Verantwortung befreit, wenn unqualifiziertes Personal

Eingriffe vornehmen und/oder keine Originalsatzteile verwenden sollte.

SCHEMA ALLACCIAMENTI INSTALLATION

INSTALLATION INSTALLATIONSBLATT

170

865

850

640

1945

1785

1835

P550-ek/P700-ek

405

P550-ek=685 P550-ek=1160

P550-ek=755

P550-ek=165

P550-ek=265

P550-ek=575

P700-ek=805 P700-ek=1250

P700-ek=845

P700-ek=227

P700-ek=322

P700-ek=402

Dis.2

190

127.5

ø100

190

ø100

390

Elettrovalvola carico - Electrovanne chargement

Water inlet - Wasseranschluß

Linea elettrica - Branchement électrique

Electric input - Netzanschluß

Water drain - Wasserablauf

Scarico acqua - Evacuation Eau

Altezza massima per scarico a muro - Hauteur maximale pour vidange à mur

Maximum height for drain to wall - Maximale Bodenhöhe für Wandwasserablauf

3/4" G

32 mm - 1"1/4 G

400 V3N 50Hz

140

ENGLISH

Second Section - FOR THE INSTALLER

During installation, carry-out a good machine levelling, which is a prerequisite for a correct

operation thereof.

The Manufacturer cannot assume any responsability for any damage to persons or

property deriving from the non-observance of the above-specified norms.

For correct installation see draw page 32.

ELECTRICAL CONNECTION

Before connecting the machine,

check to make sure the voltage

outlet of the mains is

the same as the voltage specified

on the data plate of the machine.

A main switch must be installed between

the mains and the machine. This safety

measure

also requires that the minimum distance

between the switch contacts is at least 3

mm and the

disconnection on all poles according to EN

60204 (VDE 113).

Fuses on the main switch must be 16 A .

The mains must be wired to be able to

handle the current drawn by the

machine.The system must

also be provided with a proper ground lead

in accordance with the existings norms.

The electric

cable must be of the following

type H07RN-F.

For the right choice of the cross section

area refer to the following table:

Cross Section area Total loading

mm² A

0,75 < 6

1 6 ÷ 10

1,5 10 ÷ 16

2,5 16 ÷ 25

The electrical safety of this equipment is

only assured if it is connected as follows.

It is necessary to connect the equipment to

an effective ground installation, as

specified by the

electrical safety regulations in force.

Chack that this basic requirement is

complied with and, in case of doubt, ask for

a careful check of

the installation by a qualified personal.

In addition, the equipment shall be part of

an equipotential system, the effectiveness

of which

should be checked according to the

regulations in force.

The connection should be made at the

screw marked by the respective label

located on the

equipment back side ( ).

THE MACHINE SHALL BE

CONNECTED WITH AN EFFECTIVE

GROUND CLAMP.

The manufacturer declines any

responsibility for any damages

caused by lack of an effective

ground installation.

WATER CONNECTIONS

Carefully comply with any national or

regional regulations in force.

Water installation must have the following

characteristics:

Temperature: 55°C

Dynamic Pressure :

- 2 ÷ 4 bar (200÷400 kPa);

If the dynamic pressure is lower than

specified on the data plate of the machine,

it is advisable to install a Pump for pressure

increase.

If the dynamic pressure is higher than 4

bar, it is advisable to install a pressure

reduction.

Hardness: between 7,2 and 12,5 °French.

If the hardness values are higher than

those mentioned above, it is advisable to

install a

water-softener.

WORKS TEMPERATURES

Water temperature 55°÷ 60°C

Rinse temperature 80°÷ 85°C

DO NOT TAMPER WITH THE

THERMOSTAT CALIBRATION

WATER DRAIN

According to the dimensions of the

drawing; water drain and feeding pipe

should have the same

diameter of the water inlet of the machine.

It must be furnished with a siphon and have

a right slope.

The machine is provided with a flexible pipe

for the connection with the water-work.

Make sure there are no throttlings along the

pipe.

Carefully comply with any national or

regional regulations in force.

VAPOURS SUCTION

The machine is equipped with collar for

vapours.

Carry out the necessary connection as showed

in figure.

La page charge ...

lamber P700-EK Manuel utilisateur

Marque: lamber

Modèle: P700-EK

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: lamber P700-EK Manuale utente
English: lamber P700-EK User manual

lamber P700-EK Manuel utilisateur

lamber P700-EK Manuel utilisateur

dans d''autres langues

Autres documents