BEL LDP200-120 Guide d'installation

Marque: BEL

Modèle: LDP200-120

Taper: Guide d'installation

LDP200-120

INPUT:

200 – 500 VAC, 1.4 – 0.5 A (single or two phase) or 250 – 725 VDC

OUTPUT:

24 – 120 VDC, 3 A Max (200 W Max)

MAIN FEATURES

• High efficiency and compact size

• Active PFC

• Digital control

• Wide input voltage range 170 - 550 VAC

• Wide output voltage range 24 - 120 VDC, user

settable

• User settable current limitation threshold

• Remote ON/OFF or other remote-control functions

possible through ENABLE input

• Modbus over RS-485 interface for control and

monitoring

• Multiple protections

• 2 user programmable voltage steps with settable

duration

• Can be used as battery charger (lead acid, nickel,

lithium)

• Can be used for LED lighting

• Can be paralleled for power or redundancy (with

external ORing module)

• Up to 50°C operating temperature with no

derating

• Suitable for POWERMASTER software (available

for Windows and Android)

Use latest device Documentation, Software and Firmware to ensure reliable operation of the system (downloadable from belfuse.com/power-solutions).

READ THIS CAREFULLY BEFORE

INSTALLATION!

VOR DER INSTALLATION BITTE FOLGENDE

SICHERHEITSHINWEISE BEACHTEN!

LEGGERE ATTENTAMENTE PRIMA

DELL’INSTALLAZIONE!

A LIRE ATTENTIVEMENT AVANT

L’INSTALLATION!

Before operating, read this document

thoroughly and retain it for future reference.

Non-respect of these instructions may reduce

performances and safety of the devices and

cause danger for people and property.

The products must be installed, operated,

serviced and maintained by qualified

personnel in compliance with applicable

standards and regulations.

Do not open the device, it does not contain

replaceable components, the tripping of the

internal fuse (if included) is caused by an

internal failure.

Do not repair or modify the device, if

malfunction or failure should occur during

operation, send unit to the factory for

inspection.

No responsibility is assumed by Bel for any

consequences deriving from the use of this

material.

Lesen Sie dieses Dokument vor der

Inbetriebnahme sorgfältig durch und bewahren Sie

es zum späteren Nachschlagen auf.

Die Nichtbeachtung dieser Anweisungen kann die

Funktion und Sicherheit der Geräte beeinträchtigen

und birgt Gefahren für Personen und Eigentum.

Die Geräte müssen von qualifiziertem Personal

unter Einhaltung der geltenden Normen und

Vorschriften installiert, betrieben, gewartet und

instand gehalten werden.

Öffnen Sie das Gerät nicht, es enthält keine

austauschbaren Komponenten, das Auslösen der

internen Sicherung (falls vorhanden) ist stets auf

tiefergehende Fehler im Schaltkreis zurück zu

führen.

Reparieren oder modifizieren Sie das Gerät nicht.

Sollte während des Betriebs eine Fehlfunktion oder

ein Defekt auftreten, schicken Sie das Gerät zur

Überprüfung ins Werk.

Bel übernimmt keine Haftung für die Folgen, die

sich aus dem Einsatz dieses Gerätes ergeben.

Prima dell’installazione, leggere attentamente

questo documento istruzioni e conservarle per

future consultazioni.

L’inosservanza delle presenti istruzioni può

compromettere le caratteristiche e la

sicurezza dell’apparecchio e causare pericolo

per le persone e le cose.

Il prodotto deve essere installato, utilizzato e

riparato da personale qualificato e nel rispetto

delle normative vigenti.

Non aprire il prodotto, esso non contiene

componenti sostituibili, il guasto del fusibile

interno (se previsto) è causato da un guasto

interno.

Non tentare di riparare o modificare il

prodotto, se durante il funzionamento si

verificano guasti o anomalie, inviarlo al

produttore per il controllo.

Bel non si assume nessuna responsabilità per

qualunque conseguenza derivante dall’uso di

questo materiale.

Lire ces instructions avant l'installation,

conserver ce manuel pour référence future.

Défaut de se conformer à ces instructions

peut affecter les caractéristiques et la sécurité

du dispositif, et causer du danger aux

personnes ou aux biens.

Les produits doivent être installés, exploités

et entretenus par du personnel qualifié et en

conformité avec les règlements.

N'ouvrez pas le produit, il ne contient aucune

pièce réparable, le déclenchement du fusible

interne (le cas échéant) est causé par un

défaut interne.

Ne pas essayer de réparer ou modifier le

produit ; si des défaillances se produisent

pendant le fonctionnement, retourner le

produit au fabricant pour inspection.

Bel n'assume aucune responsabilité des

conséquences éventuelles découlant de

l'utilisation des produits.

CAUTION

ACHTUNG

ATTENZIONE

AVVERTISSEMENT

RISK OF BURNS, EXPLOSION, FIRE,

ELECTRICAL SHOCK, PERSONAL INJURY.

Never carry out work on live parts! Danger of

fatal injury!

The product’s enclosure may be hot, allow

time for cooling product before touching it.

Do not allow liquids or foreign objects to enter

into the products.

To avoid sparks, do not connect or

disconnect the device before having

previously turned-off input power and wait for

internal capacitors discharge (minimum 1

minute).

GEFAHR VON VERBRENNUNGEN,

EXPLOSIONEN, FEUER, STROMSCHLAG,

PERSONENSCHÄDEN.

Führen Sie niemals Arbeiten an

spannungsführenden Teilen durch! Gefahr von

tödlichen Verletzungen! Das Gehäuse des Gerätes

kann heiß sein, lassen Sie Zeit zum Abkühlen des

Gerätes, bevor Sie es berühren.

Lassen Sie keine Flüssigkeiten oder Fremdkörper

in die Geräte eindringen.

Um Überschläge zu vermeiden, schließen Sie das

Gerät nicht an oder trennen Sie es nicht ohne

vorher die Eingangsspannung abgeschaltet zu

haben, und warten Sie die Entladung der internen

Kondensatoren ab (mindestens 1 Minute).

RISCHIO USTIONI, ESPLOSIONE,

INCENDIO, SCOSSA, LESIONI GRAVI.

Non effettuare mai operazioni sulle parti sotto

tensione! Pericolo di lesioni letali!

Il contenitore può scottare, lasciar quindi

raffreddare il dispositivo prima di toccarlo.

Non far entrare liquidi o oggetti estranei nel

dispositivo.

Per evitare scintille, non collegare o scollegare

l'apparecchiatura prima di avere tolto tensione

di ingresso e prima che sia avvenuta la

scarica dei condensatori interni (min. 1

minuto).

RISQUE DE BRULURES, EXPLOSION,

INCENDIE, ELECTROCUTION, DOMMAGE

AUX PERSONNES.

Ne jamais effectuer des opérations sur les

parties sous tension! Danger de mort!

Le boîtier peut produire des brûlures, le

laisser refroidir avant de toucher l'appareil. Ne

faire pas pénétrer des liquides ou des corps

étrangers dans l'appareil.

Pour éviter des étincelles, ne pas connecter

ou déconnecter l'équipement jusqu'à ce que

la tension d'entrée a été supprimée et avant

qu'il n'ait eut lieu la décharge des

condensateurs internes (minimum 1 minute).

INTENDED USE

BESTIMMUNGSGEMÄßER BETRIEB

USO PREVISTO

UTILISATION

These are isolated devices suitable for SELV

and PELV circuitry and are designed to be

mounted on DIN rail and installed inside a

protective enclosure. They are intended for

general use such as in industrial control,

communication, and instrumentation

equipment.

Do not use these devices in applications

where malfunction may cause injury or death.

Es handelt sich um galvanisch getrennte Geräte,

die für SELV- und PELV-Anwendungen geeignet

sind und für die Montage auf DIN-Schienen und die

Installation in einem Schutzgehäuse konzipiert

sind. Sie sind für den allgemeinen Gebrauch wie

z.B. in industriellen Steuer-, Kommunikations- und

Automatisierung-Anwendungen vorgesehen.

Verwenden Sie diese Geräte nicht in

Anwendungen, bei denen eine Fehlfunktion zu

Verletzungen oder zum Tod führen kann.

I dispositivi sono isolati, adatti per applicazioni

SELV e PELV, sono dotati di aggancio per il

montaggio su guida DIN all’interno di quadri

elettrici o contenitori di protezione, per

l’utilizzo con controllori industriali, unità di

comunicazione o apparecchi di misura.

Non utilizzare in applicazioni in cui un

eventuale guasto può comportare rischio di

lesioni o di morte.

Les produits sont isolés, appropriés pour les

circuits TBTS et TBTP et sont équipés d'un

crochet pour montage sur rail DIN dans des

armoires ou conteneurs de protection, pour

utilisation avec les contrôleurs industriels, des

modules de communication ou des unités de

mesure.

Ne pas utiliser ces dispositifs dans une

application où un dysfonctionnement pourrait

entraîner le risque des blessures ou de mort.

ENVIRONMENTAL CHARACTERISTICS

UMGEBUNGSBEDINGUNGEN

CARATTERISTICHE AMBIENTALI

CARACTÉRISTIQUES ENVIRONMENTALES

Installation in a Pollution Degree 2

environment.

Do not use in wet area or subject to moisture.

Carefully recycle the product and related

batteries according to local regulations.

Installation in einer Umgebung mit

Verschmutzungsgrad 2.

Nicht in nassen Bereichen oder unter Feuchtigkeit

verwenden.

Das Gerät und die zugehörigen Batterien sind

entsprechend den lokalen Vorschriften zu recyceln

bzw. zu entsorgen.

Usare in ambienti con Grado di Inquinamento

Non far funzionare l'apparecchio in un

ambiente umido o soggetto a formazione di

condensa. Riciclare il prodotto e le batterie

collegate, nel rispetto delle normative locali

vigenti.

Utiliser les produits dans des environnements

avec degré de pollution 2.

Ne pas employer l'appareil dans un

environnement humide ou soumis à la

condensation. Recycler les produits et les

batteries, conformément à la réglementation

locale.

Manufacturer

Bel Fuse Inc.

300 Executive Drive, Suite 300

West Orange, NJ 07052

USA

Asia-Pacific

+86 755 2988 5888

Europe, Middle East

+353 61 49 8941

North America

+1 866 513 2839

belfuse.com/power-solutions

BCM.00483_AE

This unit works as a constant voltage source or a constant current source depending on the load. The output voltage is constant until the nominal current is reached. If

more current is needed by the load the device reduces the output voltage to ensure the nominal current is not exceeded. The U/I behavior of the output is shown on

Figure 2, nominal voltage (Unom) and nominal current (Inom) are user settable and, depending on the operating mode (explained be can be altered by the ENABLE input.

Figure 2: Output voltage vs. Current

The maximum output current is limited depending on the output voltage using the

following formula:

RANGE

MAXIMUM OUTPUT CURRENT

24. – 48 VDC

Imax =5 A - (Unom/24)

Example: if Uout=36V, Imax= 5A - (36/24) = 3.5 A

48. – 120 VDC

Imax = 4 A - (3*Unom/144)

Example: if Uout=72V, Imax= 4A - (3*72/144) = 2.5 A

The user can define the device behavior using the following parameters (set by HMI or Modbus):

• Operating mode (OP): The operating mode defines the main behavior of the device. Each mode is described later on this chapter.

• Output voltage 1 (U1): See operating mode description for details of this parameter.

• Output current 1 (I1): See operating mode description for details of this parameter.

• Output voltage 2 (U2): See operating mode description for details of this parameter.

• Output current 2 (I2): See operating mode description for details of this parameter.

• Delay (Del): See operating mode description for details of this parameter.

• Enable polarity (Pol): Defines the polarity used for the enable input.

Uout

Iout

Unom

Inom

Manufacturer

Bel Fuse Inc.

300 Executive Drive, Suite 300

West Orange, NJ 07052

USA

Asia-Pacific

+86 755 2988 5888

Europe, Middle East

+353 61 49 8941

North America

+1 866 513 2839

belfuse.com/power-solutions

BCM.00483_AE

1.1 OPERATING MODES

1.1.1 Operating mode 1 (enable/disable)

In operating mode 1 the device output is turned ON/OFF by the ENABLE

input (default value= LOW).

By setting the appropriate voltage and current this mode allows using the

device as battery charger and LED lighting supply

Parameters:

Nominal voltage with output ON

Nominal current with output ON

Not used

Del

Not used

Pol

Lo or Hi

Figure 3: Operating mode 1

1.1.2 Operating mode 2 (external toggle)

In operating mode 2 the device output toggles between 2 sets of

voltage and current through the ENABLE input.

Parameters:

Nominal voltage with enable 1

Nominal current with enable 1

Nominal voltage with enable 0

Del

Not used

Pol

Lo or Hi

Figure 4: Operating mode 2

1.1.3 Operating mode 3 (enable/disable with timer)

In operating mode 3 the device output is activated by the enable

input. The output toggles to the second set of voltage and current

after a defined time. Output deactivates when the ENABLE input is

disabled.

Parameters:

First nominal voltage

First nominal current

Second nominal voltage

Second nominal current

Del

Delay for switching between U1/I1 to U2/I1

Pol

Lo or Hi

Figure 5: Operating mode

Manufacturer

Bel Fuse Inc.

300 Executive Drive, Suite 300

West Orange, NJ 07052

USA

Asia-Pacific

+86 755 2988 5888

Europe, Middle East

+353 61 49 8941

North America

+1 866 513 2839

belfuse.com/power-solutions

BCM.00483_AE

1.2 INTERFACES

1.2.1 HMI (Human Machine Interface)

An integrated user interface composed by 3 x 7 segment digits and 3 keys is present on the unit’s front panel. Layout of the menu is shown below:

Figure 6: HMI

Manufacturer

Bel Fuse Inc.

300 Executive Drive, Suite 300

West Orange, NJ 07052

USA

Asia-Pacific

+86 755 2988 5888

Europe, Middle East

+353 61 49 8941

North America

+1 866 513 2839

belfuse.com/power-solutions

BCM.00483_AE

1.2.2 MODBUS

LDP200-120 supports Modbus over RS-485 interface. The following Modbus table is implemented:

Name

Address Hex

(dec)

Modbus

type

Function

code

Res.

Min.

Max.

Comment

Device settings

Operating mode

0x1000

(4096)

Hold register

3,4,6,16

1: enable/disable

2: external toggle

3: enable/disable with timer

See §2.1 for details

Voltage 1

0x1001

(4097)

Hold register

3,4,6,16

0.1V

22V

122V

Current 1

0x1002

(4098)

Hold register

3,4,6,16

0.1A

4.5A

Voltage 2

0x1003

(4099)

Hold register

3,4,6,16

0.1V

22V

122V

Current 2

0x1004

(4100)

Hold register

3,4,6,16

0.1A

4.5A

Delay

0x1005

(4101)

Hold register

3,4,6,16

0.1s

99.9s

Enable

polarity

0x1005

(4102)

Hold register

3,4,6,16

1: active low polarity

2: active high polarity

Modbus settings (loaded on next startup)

Address

0x1100

(4352)

Hold register

3,4,6,16

247

Baudrate

0x1100

(4353)

Hold register

3,4,6,16

1: 4800

2: 9600

3: 19200

4: 38400

Parity

0x1100

(4354)

Hold register

3,4,6,16

1: None

2: Even

3: Odd

Stop bits

0x1100

(4355)

Hold register

3,4,6,16

1: 1 stop bits

2: 2 stop bits

Metering

Output voltage

0x2000

(8192)

Input

3,4

0.1V

148V

Measured output voltage

Input enable

state

0x2000

(8193)

Input

3,4

Logical state of the enable input

States

Input under

voltage

0x4000

(16384)

Discrete

input

1,2

1 when the input voltage is too low

Output short

circuit

0x4001

(16385)

Discrete

input

1,2

1 when a short circuit is detected on the output

Over temperature

0x4002

(16386)

Discrete

input

1,2

1 when device is too hot

Manufacturer

Bel Fuse Inc.

300 Executive Drive, Suite 300

West Orange, NJ 07052

USA

Asia-Pacific

+86 755 2988 5888

Europe, Middle East

+353 61 49 8941

North America

+1 866 513 2839

belfuse.com/power-solutions

BCM.00483_AE

CONNECTIONS

FIG.2 - DIMENSIONS

FIG.3 - DISTANCES

(1) AC input

(2) Enable input

(3) DC output (load)

(4) Display

(5) SET button menu

(6) UP button menu

(7) DOWN button menu

(8) Display

(9) RS-485 Comm. port

Input Connection

Single Phase

▪ L1 = Line

▪ N = Neutral

▪ = earth ground

2 Phases

▪ L1 = Phase 1

▪ L2 = Phase 2

▪ = earth ground

DC:

▪ L1 = + Positive DC

▪ N = - Negative DC

▪ = earth ground

Enable: (5 -30 VDC)

▪ + = Positive DC

▪ - = Negative DC

Output Connection

+ = Positive DC

- = Negative DC

RS-485

Signalling:

DC OK dry contact

24 VDC / 1A

▪ + = NO

▪ - = COM

▪ PIN4 = TX/RX D1

▪ PIN5 = TX/RX D0

▪ PIN8 = GND

Dimension

120

112

Distance

MOUNTING / DISMOUNTING INSTRUCTIONS

For DIN rail fastening according to IEC 60715 TH35-7.5(-15)

Mounting as shown in figure, with input terminals on lower side, with suitable cooling and maintaining a proper distance between adjacent devices as specified in the

Installation Instruction of each family.

MOUNTING:

1. Tilt the unit slightly backwards.

2. Fit the unit over the top edge of the rail.

3. Slide it downward until it hits the stop.

4. Press against the bottom for locking.

DISMOUNTING:

1. Pull down the slide clamp lever

2. Tilt the unit upward

3. Unhook the unit from the rail

1 & 2