Samsung DVG60A9900V Manuel utilisateur

FlexDry™

User manual

DVE(G)60A9900*

Untitled-5 1 2021-05-25  5:20:35

English

English2

Contents

Safety information 4

What you need to know about the safety instructions 4

Important safety symbols 4

CALIFORNIA PROPOSITION 65 WARNING 5

Important safety precautions 6

Warnings 8

Cautions 8

Regulatory notice 10

FCC Notice 10

IC Notice 11

Open Source Announcement 12

Installation requirements 13

Key installation requirements 13

Location considerations 13

Ducting requirements 16

Exhausting requirements 17

Gas requirements 18

Electrical requirements 19

Installation 21

What’s included 21

Step-by-step installation 24

Vent blockage test 31

Exhaust ducting guide 33

Door reversal 33

Before you start 36

Initial setup 36

Sort and load 37

Lint filter 37

Rack guidelines 38

Rack Dry (applicable models only) 39

Untitled-5 2 2021-05-25  5:20:35

English

English 3

Operations 40

Control panel 40

Operating a cycle 42

Cycle overview 43

Options 45

System functions 49

Special features 51

Cycle chart 53

Drying guide 58

Maintenance 59

General cleaning and maintenance instructions 59

Upper dryer 60

Lower dryer 61

Troubleshooting 62

Checkpoints 62

Information codes 64

Specifications 65

Fabric care chart 65

Protecting the environment 66

Specification sheet 66

Untitled-5 3 2021-05-25  5:20:35

English

SAVE THESE INSTRUCTIONS

English4

Safety information

Congratulations on your new Samsung dryer. This manual contains important information on the

installation, use and care of your appliance. Please take some time to read this manual to take full

advantage of your dryer’s many benefits and features.

What you need to know about the safety instructions

Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the

extensive features and functions of your new appliance. Please store the manual in a safe location close

to the appliance for future reference. Use this appliance only for its intended purpose as described in this

instruction manual.

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution and care when installing,

maintaining and operating your dryer.

Because the following operating instructions cover various models, the characteristics of your dryer may

differ slightly from those described in this manual and not all warning signs may be applicable. If you have

any questions or concerns, contact your nearest service center or find help and information online at www.

samsung.com.

Important safety symbols

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury, death and/or property damage.

CAUTION

Hazards or unsafe practices that may result in personal injury and/or property damage.

NOTE

Indicates that a risk of personal injury or material damage exists.

These warning signs are here to prevent injury to yourself and others.

Please follow them explicitly.

After reading this manual, store it in a safe place for future reference.

Read all instructions before using the appliance.

As with any equipment that uses electricity and moving parts, potential hazards exist. To safely operate

this appliance, familiarize yourself with its operation and exercise care when using it.

Untitled-5 4 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

English 5

WARNING - Risk of Fire

• Clothes dryer installation must be performed by a qualified

installer.

• Install the clothes dryer according to the manufacturer’s

instructions and local codes.

• Do not install a clothes dryer with flexible plastic venting materials.

If flexible metal (foil type) duct is installed, it must be of a specific

type identified by the appliance manufacturer as suitable for

use with clothes dryers. Flexible venting materials are known to

collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

• To reduce the risk of severe injury or death, follow all installation

instructions.

• Save these instructions.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Untitled-5 5 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

Safety information

English6

Important safety precautions

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic

precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could

ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any flammable substance, such as vegetable

oil, cooking oil, machine oil, flammable chemicals, paint thinner, etc., or anything containing wax or

chemicals, such as mops and cleaning cloths. Flammable substances may cause the fabric to catch fire

by itself.

4. Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the

appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with internal controls.

10. Do not repair or replace any part of the appliance or attempt any service unless specifically

recommended in the user-maintenance instructions or in published user-repair instructions that you

understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of

the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of

lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by qualified service

personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to

contaminated loads, the final part of a tumble dryer cycle occurs without heat (cool down period). Avoid

stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

17. This appliance must be grounded. See “Electrical requirements” and ”Grounding” in “Installation”

section.

Untitled-5 6 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

English 7

18. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the

appliance is used near children.

19. Do not insert your hand under the dryer.

-This may result in injury.

20. Take care that children’s fingers are not caught in the door when closing it.

-This may result in injury.

21. The control board and inlet valve are intentionally not grounded and may present a risk of electric

shock only during servicing.

-Do not contact these parts while the appliance is energized.

WARNING - To reduce the risk of fire or explosion:

• Do not dry items that have been previously cleaned, washed,

soaked, or spotted with gasoline, dry cleaning solvents, or other

flammable or explosive substances. They emit vapors that could

ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed

in the dryer until all traces of these flammable liquids or solids and

their fumes have been removed. There are many highly flammable

items used in homes, such as acetone, denatured alcohol, gasoline,

kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers.

• Items containing foam rubber (which may be labeled latex foam)

or similarly textured rubberlike materials must not be dried on

a heat setting. Heated foam rubber materials can, under certain

circumstances, ignite spontaneously.

Untitled-5 7 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

Safety information

English8

WARNING - What to do if you smell gas:

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer,

service agency, or the gas supplier.

Warnings

WARNING

• Ensure pockets are free of small, irregularly shaped hard objects and foreign material, i.e. coins, knives,

pins, etc. These objects could damage your dryer.

• Gas leaks may occur in your system, resulting in a dangerous situation.

Cautions

CAUTION

• Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary

when the appliance is used near children and pets.

• Before discarding or removing your dryer from service, remove the door to the drying compartment to

prevent children or animals from becoming trapped inside.

• Do not reach into the appliance when the drum is moving.

• Do not install or store this appliance where it will be exposed to the weather.

• Do not tamper with the controls.

• Do not repair, replace, or attempt to service any part of the appliance unless specifically instructed to in

the user-repair instructions and you have the understanding and skills to carry out the procedure.

Untitled-5 8 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

English 9

• Do not use fabric softeners or products to eliminate static unless the softener or product is

recommended for dryer use by the manufacturer of the fabric softener or product.

• Clean the lint screen before or after each load.

• Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

• The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel.

• This appliance must be properly grounded. Never plug the power cord into a receptacle that is

not grounded adequately or not in accordance with local and national codes. See the installation

instructions for information about grounding this appliance.

• Do not sit on top of the dryer.

• Do not dry clothing with large buckles, buttons, or other heavy metal or solid objects.

• Gas leaks may not be detected by smell alone.

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with the manufacturer’s instructions.

• Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking oil. Even

after being washed, these items may contain significant amounts of these oils.

• Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases

when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer

can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this

heat cannot escape, the items can become hot enough to catch fire. Piling, stacking, or storing these

kinds of items may prevent heat from escaping and can create a fire hazard.

• All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous.

Washing these items in hot water with extra detergent will reduce, but not eliminate, the hazard.

Always use the Cool Down cycle for these items to reduce their temperature. Never remove these items

from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle.

Never pile or stack these items when they are hot.

Untitled-5 9 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

English10

Regulatory notice

FCC Notice

CAUTION

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received including interference that cause undesired

operation.

For products sold in the US and Canadian markets, only channels 1–11 are available. You cannot select any

other channels.

FCC STATEMENT:

This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorienting or relocating the receiving antenna

• Increasing the separation between the equipment and receiver

• Connecting the equipment to an outlet that is on a different circuit than the radio or TV.

• Consulting the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated so there is at least 8 inches (20 cm) between the radiator

and your body. This device and its antenna(s) must not be colocated or operated in conjunction with any

other antenna or transmitter.

Untitled-5 10 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

English 11

Unintentional emitter per FCC Part 15

Product type : Clothes Dryers

Model : DVE(G)60A9900*

Responsible Party – U.S. Contact Information

Samsung Electronics America, Inc.

QA Lab America

19 Chapin Rd. Building D Pine Brook NJ 07058

Tel: 1-973-808-6375 Fax: 1-973-808-63

IC Notice

The term “IC” before the radio certification number only signifies that Industry Canada technical

specifications were met. Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of

the device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

For products sold in the US and Canadian markets, only channels 1–11 are available. You cannot select any

other channels.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated so there is at least 8 inches (20 cm)

between the radiator and your body. This device and its antenna(s) must not be colocated or operated in

conjunction with any other antenna or transmitter.

Untitled-5 11 2021-05-25  5:20:36

English

SAVE THESE INSTRUCTIONS

Regulatory notice

English12

Open Source Announcement

The software included in this product contains open source software.

The following URL http://opensource.samsung.com/opensource/SMART_TP2_0/seq/0 leads to open

source license information as related to this product.

NOTE

Hereby, Samsung Electronics, declares that the radio equipment type appliance is in compliance with

Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet

address: The official Declaration of conformity may be found at http://www.samsung.com, go to Support >

Search Product Support and enter the model name.

Wi-Fi max transmitter power : 20 dBm at 2.412 GHz – 2.472 GHz

Untitled-5 12 2021-05-25  5:20:36

English

English 13

Installation requirements

Read through the following instructions before installing the dryer and keep this manual for future

reference.

WARNING

Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing.

Service Personnel - Do not contact the following parts while the appliance is energized: Control board and

inlet valve.

Key installation requirements

• A grounded electrical outlet.

• A power cord for electric dryers (except in Canada).

• Gas lines (for gas models) that must meet national and local regulations.

• An exhaust system made of rigid metal or flexible stiff-walled metal exhaust ducting.

WARNING

Remove the door from all discarded appliances to prevent a child from suffocating.

Location considerations

The dryer should be located where there is enough space at the front for loading the dryer, and enough

space behind for the exhaust system. This dryer is factory-ready for the rear exhaust option. To exhaust out

the bottom, right or the left, use the accessory exhaust kit. Instructions are included with the kit. Make sure

the room in which the dryer is located has enough fresh air. The dryer must be located where there are no

air-flow obstructions. For gas dryers, adequate clearance must be maintained as noted on the data plate to

ensure adequate air for combustion and the proper dryer operation.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. The

dryer area must be kept clear of combustible materials, gasoline, and other flammable vapors and liquids.

A dryer produces combustible lint. The area around the dryer should be kept lint-free.

Untitled-5 13 2021-05-25  5:20:36

English

Installation requirements

English14

Alcove or closet installations

WARNING

• The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or

closet.

• No other fuel-burning appliance should be installed in the same closet as the dryer.

• Place the dryer at least 18 inches (460 mm) above the floor for garage installation.

Minimum clearances between the dryer and adjacent walls or other surfaces:

Sides 1 in. (25 mm) Rear 5.9 in. (150 mm)

Top 21 in. (533 mm) Closet front 2 in. (51 mm)

If both the washer and a dryer are installed in the same location, the front of the alcove or closet must have

two unobstructed air openings for a combined minimum total area of 72 in.2 (465 cm2).

Installation with pedestal

A

C

B D

F

E

A52.9 in. (1343 mm) D27 in. (686 mm)

B32.5 in. (825 mm) E46.9 in. (1192 mm)

C5.9 in. (150 mm) F52.2 in. (1326 mm)

Untitled-5 14 2021-05-25  5:20:36

English

English 15

Side by side installation

A

E

A

C

B B

F

D

A1 in. (25 mm) D32.5 in. (825 mm)

B27 in. (686 mm) E2 in. (50 mm)

C21 in. (533 mm) F5.9 in. (150 mm)

A

A61 in. (1550 mm)

Untitled-5 15 2021-05-25  5:20:36

English

Installation requirements

English16

Ducting requirements

Weather hood type

Recommended Use only for short-run

installation

4” (10.2 cm) 2.5” (6.4 cm)

No. of 90° elbows Rigid Rigid

080 ft. (24.4 m) 74 ft. (22.6 m)

168 ft. (20.7 m) 62 ft. (18.9 m)

257 ft. (17.4 m) 51 ft. (15.5 m)

347 ft. (14.3 m) 41 ft. (12.5 m)

NOTE

* Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.

If you integrate the dryer’s vent system with an existing exhaust system:

• Make sure the exhaust system meets all applicable local, state, and national regulations.

• Verify you are not using flexible plastic duct.

• Make sure to check for and remove all lint buildup from inside the existing ducts.

• Confirm the duct is not kinked or crushed.

• Make sure the exhaust hood damper opens and closes freely.

Manometer measurements

The static pressure in any exhaust system must not exceed 0.83 inches of water column or be less than 0.

Note that these values are measured with the dryer running with a manometer presented to the exhaust

duct that connects to the dryer. The dryer drum must be empty and lint filter clean.

Untitled-5 16 2021-05-25  5:20:37

English

English 17

Exhausting requirements

The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed

space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture

from being blown into the room.

In the United States and Canada

• All dryers must be exhausted to the outside.

• The required exhaust duct is 4 inches (10.2 cm) in diameter.

• See the Ducting requirements section on page 16 for the maximum duct length and number of bends

that can be used.

• The total length of flexible metal duct must not exceed 7’ 101/2” (2.4 m).

• Do not assemble the duct with screws or other fasteners that extend into the duct and catch lint.

• For the United States only: Use only those foil-type flexible ducts, if any, specifically identified for use

with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition

Duct. Use Subject 2158A.

Outside the United States and Canada

• Refer to the local codes.

WARNING

• You must exhaust the dryer to the outside to reduce the risk of fire when you install the dryer in an

alcove or closet.

• Do not use a plastic or non-metal flexible duct.

• If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

• Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air, heat, and

lint.

Untitled-5 17 2021-05-25  5:20:37

English

Installation requirements

English18

Gas requirements

WARNING

• Use only natural or LP (liquid propane) gases.

• The installation must be conformed with local codes, or in the absence of local codes, with the national

fuel gas code, ANSI Z223.1/NFPA 54, latest revision (for the UNITED STATES), or with the natural gas and

propane installation code, CSA B149.1 (for Canada).

• Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with

LP (liquid propane) gas, it must be converted for safe and proper performance by a qualified service

technician. (LNG models only)

You must check the burner of your model and use the proper LP Kit accordingly. To check the detail

information of the burner, open the door and check the rating label location on the door frame.

-20,000 BTU: LPKIT-4/XAA (DC98-04114A)

-22,000 BTU: LPKIT-3/XAA (DC99-00792A)

• A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-

off valve be installed within 6” of your dryer.

• Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

• Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

• Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

• Do not reuse old flexible metal gas lines. Flexible gas lines must be designed and certified by the

standard for connectors for Gas Appliances, ANSI Z21.24 • CSA 6.10.

NOTE

• Your dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot.

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

Commonwealth of Massachusetts installation instructions

Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be

installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the

connector can be no longer than 3’ (36”).

WARNING

• Gas leaks may occur in your system, creating a dangerous situation.

• Gas leaks may not be detected by smell alone.

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with the manufacturer’s instructions.

Untitled-5 18 2021-05-25  5:20:37

English

English 19

Electrical requirements

The wiring diagram is located on the plate under the control panel or rear frame.

WARNING

• Improperly connecting the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly

grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper

outlet installed by a qualified electrician.

• To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding must be

done in accordance with local codes, or in the absence of local codes, in accordance with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA

C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide adequate

electrical service for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest

Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and local

codes and ordinances.

Grounding

This dryer must be grounded. In the event of a malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

• Your dryer has a cord with an equipment-grounding conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly installed and grounded in accordance with all local

codes and ordinances.

• Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Electric models

WARNING

• Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug. This

cord is sold separately.

• The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

• Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

• If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be

connected to a permanently grounded metal wiring system, or an equipment grounding conductor

must be run with the circuit conductors and connected to the equipment grounding terminal or lead on

the dryer.

Untitled-5 19 2021-05-25  5:20:37

English

Installation requirements

English20

Electrical connections

Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual

branch (or separate) circuit serving only your dryer is recommended.

Do not use an extension cord.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some require 120 / 208 volt,

60 Hz approved electrical service. The electric service requirements can be found on the data label located

behind the door. A 30-ampere fuse or circuit breaker on both sides of the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is not provided with U.S. electric model dryers. This cord is sold separately.

Risk of Electric Shock

WARNING

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be

supported at the dryer cabinet by a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2)

mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the

neutral conductor. (Use a 4-prong plug for a 4 wire receptacle, NEMA type 14-30R.)

Electric models – Canada Only

A 120 / 240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker on

both sides of the line is required.

NOTE

All Canadian models are shipped with the power cord attached. The power cord should be plugged into a

30-ampere receptacle. In Canada, you may convert a dryer to 120 / 208 volts.

Untitled-5 20 2021-05-25  5:20:37

La page charge ...

Samsung DVG60A9900V Manuel utilisateur

Ce manuel convient également à

Samsung DVG60A9900V Manuel utilisateur

dans d''autres langues

Documents connexes