TCL TWC-22CR2/UH Mode d'emploi

TWC-15CR/UH(ES)

TWC-18CR2/UH(ES)

TWC-22CR2/UH(ES)

TWC-24CR2/UH(ES)

INTRODUCTION

IMPORTANT SAFETY INSTRUCTION ...........................................................................

...................................................................................

PACKING LIST ............................................................................................................

INSTALLATION & ASSEMBLY INSTRUCTIONS ..............................................................

USING YOUR AIR CONDITIONER ................................................................................

........................................................................

CARE AND CLEANING ................................................................................................

TROUBLESHOOTING .................................................................................................

ELECTRICAL REQUIREMENTS

OPERATING YOUR AIR CONDITIONER

1

2

3

4

13

15

16

17

1

2

15K 18K/22K/24K

3

5/8" Long Hex-head Screw

1/2" Long Hex-head Screw

5/8" Long Flat Head Bolt and

Locknut

5/16" Long Hex-head Screw

Sill Angel Bracket

1/2" Long Flat Head Bolt and

Locknut

Gasket

Support Bracket(with R and L

remark)

4

15K/18K

17.91 18.625

23.625 26.50

19.00 19.50

28.00 30.00

41.00 41.00

22K/24K

SASH

1/2 MIN

19 MIN

19 1/2 MIN

FIG.1

FIG.3

Storm Window Frame or Obstruction

FIG.2

FIG.4

SASH

1/2 MIN

19 MIN

19 1/2 MIN

1/2 MIN

Storm Window Frame

or Obstruction

5

(15K/18K See FIG.1/FIG.2 ; 22K/24K See FIG.3/FIG.4).

Storm Window Frame

or Obstruction

6

FIG.5

FIG.6

FIG.7 & 8

FIG.7

FIG.8

FIG.9

7

6.Remove the six screws from the cabinet.( ) (FIG.10)There are two screws on the top, left and right.

FIG.10

FIG.11

8. (FIG.12).Remove the shipping block for the 24K

FIG.12

Do not

pull or

lift in

this

area

This may

result in

damage.

8

5/16" Long

Hex-head Screw

FIG.13a

(FIG.13b-14).

FIG.13b

5/16

Long

Hex-head

Screw

(

)

It is suggested to keep a downward angle so

accumulated rain water can drain out from the

backside of the unit.

FIG.14

9

5/8" Long Flat Head Bolt

Long Flat head

Bolt and Locknut

Long

Flat head Bolt

and Locknut

5/8" Long

Hex-head Screw

1/2" Long

Hex-head Screw

5/8" Long

Hex-head Screw

5

(It should set on the gasket for 22K/24K)

Gasket

5/8" Long

Hex-head Screw

Sash Lock

sash lock

10

FIG.15

11

15K/18K

18 1/4 (46.4 cm)

23 7/8 (60.6 cm)

22K/24K

19 1/2 (49.5 cm)

26 9/10 (68.3 cm)

Y

FIG.16

FIG.18

FIG.17

(Page 6 and 7)

12

FIG.19

FIG.20

13

1

2

3

4

5

6

7

8

9

1. Without timer setting,the

operation mode is Cooling,Dry, Fan and Auto,and

the set temperature will be displayed.

Time will be displayed under timer setting.

Digital Display:

and Button:2. Use these buttons on the

control panel and remote to increase or decrease

the Set Temperature or Timer.

Temperature range: 61 ~88 or 16 ~31 .

3. Turn the air conditioner on and

off.

Power Button:

Press the mode button to cycle

through the various modes: Cool, Dry, Fan and

Auto.

4. Mode Button:

Use these buttons on the control

panel and remote to set the Timer.

Timer Off: The timed stop is programmed by

pressing TIMER button. Set the rest time by

pressing the button or until the rest

time displayed is to your demand then press

TIMER button again.

Timer On: When the unit is off, press TIMER

button at the first time, set the temperature with

pressing the button or . Press TIMER

button at the second time, set the rest time with

pressing the button or . Press TIMER

button at the third time, confirm the setting,

Note: It can be set to automatically turn off or on

in 0.5-24 hours. Each press of the

buttons will increase or decrease the timer. The

Timer can be set in 0.5 hours increment below 10

hours and 1 hour increment for 10 hours or above.

The SET light will turn on while setting.

To cancel the set function, press the TIMER

button again.

then it

will automatically switch on and show on the

display.

5. Timer Button:

Cool Mode: The cooling function allows the air

conditioner to cool the room and at the same time

reduces Air . Press the MODE button to

activate the cooling function. To optimize the

function of the air conditioner, adjust the

temperature and the speed by pressing the button

indicated.

Dry Mode: This function reduces the humidity of

the air to make the room more comfortable. Press

MODE button to set the DRY mode. An automatic

function of alternating cooling cycles and air fan

is activated.

Fan Mode: The conditioner works in only

ventilation. Press MODE button to set the FAN

mode. With pressing FAN SPEED button the

speed changes in the following sequence: Hi, Med

and Lo in FAN mode. The remote control also

stories the speed that was set in the previous

mode of operation.

humidity

Auto Mode: In AUTO mode the unit automatically

chooses the fan speed and the mode of operation

(COOL,DRY or FAN).In this mode the fan speed

and the temperature are set automatically

according to the room temperature (tested by the

temperature sensor which is incorporated in the

indoor unit.).

AUTO

SPEED

AUTO

MODE

14

When the unit is in ECO mode, the

light will turn on. In ECO mode, the unit will

turn off once the room is cooled to the user set

temperature. The fan will also be off at this point.

The unit will turn back on when the room

temperature rises above the user set temperature.

Before the compressor starts, the fan motor will

run for a while, then it will stop for a while, and will

repeat to provide a much more comfortable feeling

and save energy.

6. Eco Button:

Press the SLEEP button, the Sleep

Light will be on , and

In SLEEP mode, the air-

conditioner will automatically adjust the tempera-

ture and fan speed to make the room more comfor-

table during the night. The set temperature will

automatically raise by 1 every 30-60 minutes

and at most change six times until the set

temperature is .

for 10 seconds then all of the

display lights will turn off.

.8

82.4

7. Sleep Button:

Press the FAN SPEED button

to choose the fan speed options. You can choose

Hi, Med, Lo or auto speed in COOL mode and

choose Hi, Med, Lo in FAN mode.

8. Fan Speed Button:

9.

When the Filter Check light is off,

it is useless to press the Filter Check button. When

the Filter Check light is on, it can turn off the light

by pressing the Filter Check button. After the

fan motor works for 500 total hours, the Filter

Check light will turn on to remind the user to clean

the filter.

Filter Button:

10.

To direct the airflow,

horizontal wheel to control the horizontal

direction, control the

vertical direction.

use the

and use the air deflectors to

Directional Louvers:

horizontal wheelair deflector air deflector

15

Fan Only:

Press the FAN SPEED button to

choose the fan speed options. You can choose

Hi, Med, Lo or auto speed in COOL mode and

choose Hi, Med, Lo in FAN mode.

7. Fan Speed:

To press the DISPLAY button, it can

switch off/on all lights or LED display.

8. Display:

Use these buttons on the control panel

and remote to set the Timer.

Timer Off: The timed stop is programmed by

pressing TIMER button. Set the rest time by

pressing the button or until the rest

time displayed is to your demand then press

TIMER button again.

Timer On: When the unit is off, press TIMER

button at the first time, set the temperature with

pressing the button or . Press TIMER

button at the second time, set the rest time with

pressing the button or . Press TIMER

button at the third time, confirm the setting, then

the rest time to next automatical switching-on

could be read on the display of the machine.

Note: It can be set to automatically turn off or on

in 0.5-24 hours. Each press of the

buttons will increase or decrease the timer. The

Timer can be set in 0.5 hours increment below

10 hours and 1 hour increment for 10 hours or

above. The SET light will turn on while setting.

To cancel the set function, press the TIMER

button again.

5. Timer:

In AUTO mode the unit automatically

chooses the fan speed and the mode of operation

(COOL,DRY or FAN).In this mode the fan speed

and the temperature are set automatically according

to the room temperature (tested by the temperature

sensor which is incorporated in the indoor unit.).

6. Auto Mode:

Press the SLEEP button, the Sleep

Light will be on , and

In SLEEP mode, the air-

conditioner will automatically adjust the tempera-

ture and fan speed to make the room more comfor-

table during the night. The set temperature will

automatically raise by 1 every 30-60 minutes

and at most change six times until the set

temperature is .

for 10 seconds then all of the

display lights will turn off.

.8

82.4

4. Sleep:

1. Turn the air conditioner on and off.Power:

2. Press the COOL button to COOL mode.Cool:

and :3. Use these buttons on the control

panel and remote to increase or decrease the

Set Temperature or Timer. Temperature range:

61 ~88 or 16 ~31 .

1

4

5

6

3

7

8

10

9

2

When the unit is in ECO mode, the light

will turn on. In ECO mode, the unit will turn off

once the room is cooled to the user set

temperature. The fan will also be off at this

point. The unit will turn back on when the room

temperature rises above the user set

temperature.Before the compressor starts, the fan

motor will run for a while, then it will stop for a while,

and will repeat to provide a much more comfortable

feeling and save energy.

Press the Fan Only button to FAN

ONLY mode.

9.

10.

Eco:

16

FIG.21

La page charge ...

TCL TWC-22CR2/UH Mode d'emploi

TCL TWC-22CR2/UH Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents