Chief ROTRS Guide d'installation

Catégorie
Accessoires de rack
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Pull Out and Rotating Rack Shelf
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
ROTRS
ROTRS Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the rack does not exceed 250
lbs (113.4 kg). Use with products heavier than the maximum
weight indicated may result in instability or collapse of the
rack causing possible injury.
IMPORTANT ! : Minimum spacings between the Accessories
and components and the (ITC/AV) Rack Enclosure shall be
maintained for safe operation of the equipment when installed
in accordance with the National Electric Code, ANSI/NFPA 70-
2008. Operating temperature inside rack shall not exceed
104°F.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
18.88
479.4
Installation Instructions ROTRS
3
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
7/16"
1/4"
A ()
[ROTRS shelf]
B ()
C (4)
#4-40
[shelf bracket]
D (4)
#4-40 x 1/4"
E (4)
1/4-20
F (4)
1/4-20 x 1/2"
ROTRS Installation Instructions
4
ASSEMBLY
1. Attach shelf brackets (B) to ROTRS shelf (A) using four #4-
40 x 1/4" pem studs (C) and four #4-40 lock nuts (D). (See
Figure 1)
NOTE: Brackets may be installed anywhere on shelf where
there are mounting slots based on user preference.
Figure 1
2. Use four 1/4-20" lock nuts (E) and four 1/4-20 x 1/2" pem
studs (F) to secure shelf to ROTR rack at desired mounting
height. (See Figure 2)
IMPORTANT ! : Shelf can only be mounted using larger
diameter holes in ROTR rack rails. Pem studs will not fit
through the smaller holes.
Figure 2
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the rack does not exceed 250
lbs (113.4 kg). Use with products heavier than the maximum
weight indicated may result in instability or collapse of the
rack causing possible injury.
3. Install desired components to shelf.
(A)
(B) x 2
(C) x 4
1
(D) x 4
2
(E) x 4
(F) x 4
ROTR
Installation Instructions ROTRS
5
ROTRS Installation Instructions
6
Installation Instructions ROTRS
7
ROTRS Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002243 Rev00
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
12/12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief ROTRS Guide d'installation

Catégorie
Accessoires de rack
Taper
Guide d'installation

dans d''autres langues