Jenn-Air MFX2876DRH00 Guide d'installation

Marque: Jenn-Air

Modèle: MFX2876DRH00

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATIONINSTRUCTIONSAND OWNER'S MANUAL

_ _ ........ ;;_y......

Do Not Throw Away -- Additional important safety information included.

Para las instrucciones en espat_ol, visite nuestro sitio de internet.

INSTRUCTIONSD'INSTALLATIONETMANUEL D'UTILISATION

_?_..¢_c_+,_:_k__'_ ._:.po_ G dot.._bl_;_, __:_l'tI_i".....co_"_'_g@C_,Fi_t..__ " ..... _ 1""___

Nepas jeter -- Autres consignes de s_curit_ importantes ci-joinles.

Table of Contents / Tabledes mati@res

REFRIGERATOR SAFETY ..................................................................... 2

Proper Disposal of Your Old Refrigerator ........................................... 3

INSTALLATION INSTRUCTIONS ......................................................... 3

Unpack the Refrigerator ...................................................................... 3

Remove and Replace Refrigerator Doors ........................................... 4

Remove and Replace Drawer Fronts .................................................. 6

Location Requirements ....................................................................... 8

Electrical Requirements ...................................................................... 9

Water Supply Requirements ............................................................... 9

Connect the Water Supply .................................................................. 9

Handle Installation and Removal ...................................................... 11

Refrigerator Leveling, Door Closing and Alignment ......................... 12

FILTERS AND ACCESSORIES ........................................................... 13

Water Filtration System ..................................................................... 13

Install Air Filter (on some models) ..................................................... 14

REFRIGERATOR USE ......................................................................... 15

Opening and Closing Doors .............................................................. 15

REFRIGERATOR CARE ....................................................................... 15

Cleaning ............................................................................................ 15

Lights ................................................................................................. 16

Vacation and Moving Care ............................................................... 16

PROBLEM SOLVER ............................................................................. 17

WATER FILTER CERTIFICATIONS .................................................... 22

PERFORMANCE DATA SHEET .......................................................... 23

SECURITE DU REFRIGERATEUR ..................................................... 24

Mise au rebut adequate de votre vieux refrigerateur ....................... 25

INSTRUCTIONS D'INSTALLATION ................................................... 25

Deballage du refrigerateur ................................................................ 25

Retrait et reinstallation des portes du refrigerateur .......................... 26

Retrait et reinstallation de I'avant des tiroirs .................................... 28

Exigences d'emplacement ............................................................... 30

Specifications electriques ................................................................. 31

Specifications de I'alimentation en eau ............................................ 31

Raccordement &la canalisation d'eau ............................................. 31

Installation et demontage des poignees .......................................... 33

Mise & niveau du refrigerateur,

fermeture et alignement des portes ................................................. 34

FILTRES ET ACCESSOIRES ............................................................... 36

Systeme de filtration d'eau ............................................................... 36

Installation du filtre & air .................................................................... 37

UTILISATION DU R#FRIG#RATEUR ................................................. 38

Ouverture et fermeture des portes ................................................... 38

ENTRETIEN DU R#FRIG#RATEUR ................................................... 38

Nettoyage .......................................................................................... 38

Lampes ............................................................................................. 39

Entretien avant les vacances ou Iors d'un demenagement ............. 40

R#SOLUTION DE PROBL#MES ........................................................ 41

FEUlLLE DE DONN#ES SUR LA PERFORMANCE .......................... 47

W10538548A

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet.

[] Do not remove ground prong.

[] Do not use an adapter.

[] Do not use an extension cord.

[] Disconnect power before servicing.

[] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

[] Use nonflammable cleaner.

[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.

[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models).

[] Do not hit the refrigerator glass doors (on some models).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper DisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT" Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATIONINSTRUCTIONS

(£ pGck R®f g® o.............

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

Clean Before Using

After you remove all of the packaging materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

"walk" the refrigerator when trying to move it, as floor

damage could occur.

NOTE:Measurethewidthofyourdooropening,toseewhetherornotyouneedtoremovetherefrigeratordoorstomovethe

refrigeratorintoyourhome.Ifdoorremovalisnecessary,seethefollowinginstructions.

IMPORTANT:Iftherefrigeratorwaspreviouslyinstalledandyouaremovingitoutofthehome,beforeyoubegin,turntherefrigerator

controlOFRUnplugtherefrigeratorordisconnectpower.Removefoodandadjustabledoororutilitybinsfromdoors.

Gathertherequiredtoolsandreadallinstructionsbeforeremovingdoors.

TOOLSNEEDED:3/le"hexkeywrenchanda#2Phillipsscrewdriver

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Style I - Water Dispenser

Tubing Connection

A. Outer Ring

Wiring Plug

Top Left Hinge

A B

A. _6" Internal Hex-Head Screws

B. Ground Wire (Do Not Remove)

C. Do Not Remove Screws

Style 2 - Water Dispenser

Tubing Connection

A. Outer Ring

Door Removal

I @

A. _8" Internal Hex-Head Screws

B. Hinge Cover Screw

C. Top Hinge Cover

D. Top Hinge

Remove Right-Hand Refrigerator Door

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

Using a Phillips screwdriver, remove the cover from the Top

Hinge.

Using the ¾e" hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTE: Do not remove the two Iocator screws. These screws

will help you align the hinge when you replace the door.

I I

Remove Left-Hand Refrigerator Door

IMPORTANT: The tubing and wiring for the water dispenser run

through the left-hand door hinge, so they must be disconnected

before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top

hinge.

A. Top hinge cover screw B. Top hinge cover

Disconnect the water dispenser tubing located on top of the

door hinge.

Style 1- Press the outer ring against the face of the fitting and

gently pull the dispenser tubing free.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

A. Top hinge cover screw

B. Top hinge cover

C. _11 Internal hex head screws

D. Top hinge

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

A. Outer ring

B. Face of fitting

Style 2 - Firmly pull up on the clasp. Then, pull the tubing out

of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

Disconnect the wiring plug located on top of the door hinge.

• Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of

the plug apart.

NOTE: Do not remove the green, ground wire. It should

remain attached to the door hinge.

Using the 34e"hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTES:

Provide additional support for the refrigerator door while

the hinges are being removed. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

Do not remove the two Iocator screws. These screws will

help you align the hinge when you replace the door.

A B

A. _" Internal hex head screws

B. Ground wire (do not remove)

C.Locator screws (do not

remove)

Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

• Only if necessary, use a driver with a #2 square bit tip to

remove the bottom hinges and a 3/8"nut driver to remove

the brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the two 3/le"internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the two 3/le"internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

Reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the

outer ring is touching the face of fitting.

Style 2 - Insert the tubing firmly into the fitting until it stops.

Close the clasp around the tubing. The clasp snaps into place

between the fitting and the collar.

Reconnect the electrical wiring.

• Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the four internal hex head screws (two on

the right-hand door hinge and two on the left-hand door

hinge).

2. Replace both top hinge covers.

Depending on the width of your door opening, it may be

necessary to remove the drawer fronts to move the refrigerator

into your home.

IMPORTANT:

If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food from the drawers.

• Two people may be required to remove and replace the

drawer fronts.

Tools Needed: V4"Hex head nut driver, Flat-blade screwdriver

Refrigerated Drawer

Disconnect Wiring

NOTES:

• The exterior refrigerator drawer front is connected to the

temperature control. Before removing the drawer front, the

wires must be disconnected from the temperature control.

The cable visible behind and under the pantry drawer at the

right side contains wiring for the pantry control and moves

with the drawer as it is pulled out. There is no need to

disconnect this cable.

Open the drawer to its full extension, and remove the large

interior bin.

Locate the wiring cover on the backside of the drawer front.

Press tab on the cover to release the snaps, and pull off cover

to reveal the wiring connection.

A. Press tab B. Wiring connection cover

On one side of the wiring connector, insert the screwdriver

blade between the connector tab and the connector to

release. Repeat for the opposite side. Pull the wiring

connector apart.

Remove Drawer Front

1. Using a 1/4"hex head nut driver, remove the two bottom

screws (one on each side) attaching the drawer front to the

drawer glides.

2. Using 1/4"hex head nut driver, loosen the two top screws (one

on each side) attaching the drawer front to the drawer glides.

NOTE: Loosen the screws three to four turns. Keep the

screws in the drawer front.

3. Lift the drawer front up and off the drawer glide brackets.

Reconnect Wiring

1. Align the two ends of the wiring connector and push them

together until you hear a "click" sound and feel the tabs snap

into place on the connector.

2. Gently pull on the wiring connection to ensure the wiring

connection is completely seated. Replace the wiring cover.

NOTE: The wiring connection must be complete for the

drawer temperature control to operate.

3. Replacethe interiorbin.

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the two top screws that fasten the drawer front to the

drawer glides. The two screws (one on the left-hand side and

one on the right-hand side) are located inside the drawer front.

3. Lift up on the drawer front to release the plastic studs from the

drawer glide bracket slots.

A. Loosen top screws

B. Drawer glide bracket

C. Remove bottom screws

4. Slide the drawer glides back into the refrigerator.

Replace Drawer Front

1. Pull out the drawer glides until they are fully extended.

2. Lower the loosened screws in the top of the drawer front into

the upper notches in the drawer glides.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

screws into the notches.

3. Align the holes in the bottom of the drawer front with the holes

in the bottom of the drawer glides and fasten with the screws

removed earlier.

4. Tighten the two top screws.

A.Drawer glide bracket slots

Slide the drawer glides back into the freezer.

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the two plastic

studs, located at the bottom, inside the drawer front, with the

drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

studs into the slots.

A s_sJ_

A. Drawer front screw

B. Drawer front plastic stud

3. Replace and tighten the two screws at the top of the drawer

front (one on the left-hand side and one on the right-hand

side).

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See "Using the Control(s)" and

"Temperature Controlled Exterior Drawer."

3. Return all removable parts and the food to the drawers.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, allow for a V2"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 33/4'' (9.5 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a maximum

of 110°F (43°C). The preferred room temperature range for

optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

1/2" (1.25 cm)

33/4" (9.5 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the

refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn Cooling

ON. See "Using the Control(s)."

A cold water supply with water pressure between 35 and 120 psi

(241 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

NOTE: Ifthe water pressure is less than what is required, the flow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy use. The tank capacity could be too small to keep

up with the requirements of the refrigerator.

NOTE: Faucet mounted reverse osmosis systems are not

recommended.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration

System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT:

• Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX

(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid off-taste or odor in your ice

or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701 RP (25 ft [7.62 m] PEX).

• Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/le"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4"nut driver

NOTE: Do not use a piercing-type or 3A+"(4.76 mm) saddle valve

which reduces water flow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is

connected, turn the ice maker OFE

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

1/2"household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1/2"size household supply line is recommended.

A. Sleeve

B. Nut

II I

C. Copper tubing (to refrigerator)

D. Household supply line (_/2"minimum)

Now you are ready to connect the copper tubing to the shutoff

valve. Use 1/4"(6.35 mm) OD soft copper tubing to connect the

shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specific to your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

A _

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end

of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the cabinet.

A B C D

A. Household water line C. Ferrule (purchased)

B. Nut (purchased) D. Refrigerator water tubing

Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the 1/4"(6.35 mm) water line at either tube

connection. Obtain a water strainer from your appliance

dealer.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill the ice storage bin.

A. Copper tubing

B. "P" clamp

C. Compression nut

D. Compression sleeve

Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Parts Included: Refrigerator door handles (2), Refrigerator drawer

handle (1), Freezer drawer handle (1), 1/8"hex key, spare

setscrew(s)

Refrigerator and Freezer Drawers

1. With the drawer closed, place the handle onto the shoulder

screws so that the setscrews are facing down toward the floor.

Install Handles

Refrigerator Doors

NOTE: Handle mounting setscrews are preinstalled inside the

handle.

1. Remove the handles from the packaging inside the

refrigerator, and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed door,

place a handle onto the shoulder screws so that the setscrews

are facing the adjacent door.

A.Shoulder screws

B.Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

Using a clockwise motion tighten the setscrew just until it

begins to contact the shoulder screw. Do not fully tighten.

Repeat steps 4 and 5 to fasten the lower setscrew.

Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

Repeat steps 2 through 7 to install the other handle onto the

adjacent refrigerator door.

A. Shoulder screw

B. Setscrews inside the handle

2. Firmly push the handle toward the drawer until the handle

base is flush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

Using a left to right motion tighten the setscrew a quarter-turn

at a time just until it begins to contact the shoulder screw. Do

not fully tighten.

Repeat steps 11 and 12 to fasten the right-hand setscrew to

the shoulder screw.

Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into asetscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right to left motion loosen the setscrew a quarter-turn

at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

The base grille covers the adjustable brake feet and roller Style 2

assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the base

grille and move the refrigerator to its final location.

Tools Needed: V4"hex nut driver

Tools Provided: W' hex key wrench

1. Remove the base grille. Using both hands, grasp the grille

firmly and pull it toward you. Open the freezer drawer to

access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the break

feet by turning them counterclockwise. The front rollers will

be touching the floor.

A. Brake foot

Move the refrigerator to its final location.

Using the V4"hex nut driver, lower the brake feet. Turn them

clockwise, until the rollers are off the floor and both brake feet

are snug against the floor. This keeps the refrigerator from

rolling forward when opening the refrigerator doors or freezer

drawer.

IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the

same amount to keep the refrigerator level.

Make sure the doors close easily. Ifyou are satisfied with the

door opening and closing, skip the next section and go to

"Align the Doors." If, however, the doors do not close easily or

the doors pop open, adjust the tilt.

To Adjust the Cabinet Tilt:

Open the freezer drawer. Use a V4"hex nut driver to turn

both brake feet clockwise the same amount. This will raise

the front of the refrigerator. It may take several turns to

allow the doors to close easier.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This

makes it easier to turn them.

Style 1

_ _r_ O A

A. Brake foot

B. Front roller

Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of

the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

Keeping both refrigerator doors closed, pull out the

refrigerated drawer. Locate the bottom hinge pin of the

right-hand refrigerator door. The alignment screw is inside

the bottom hinge pin.

A.Bottom hingepin

B. Turnto the right to raise.

C. Turnto the left to lower.

D. _" Hex keywrench

Insert the short end of the V8"hex key wrench (packed

with the Door Handle Installation Instructions) into the

bottom hinge pin until it is fully engaged in the alignment

screw.

To raise the door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

Continue to turn the alignment screw until the doors are

aligned.

Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when a door or drawer is pulled

open, adjust the brake feet.

To Steady the Refrigerator:

Open the freezer drawer. Using a V4"hex driver, turn both

brake feet clockwise the same amount until the brake feet

are snug against the floor. Check again. If not satisfied,

continue to adjust the brake feet by half turns of the screw

until the refrigerator does not roll forward when the drawer

is opened.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This

makes it easier to turn the screws.

Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille

into place.

FILTERSAND ACCESSORIES

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Install the Water Filter

Locate the accessory packet in the refrigerator and remove

the water filter.

Take the water filter out of its packaging and remove the cover

from the O-rings. Be sure the O-rings are still in place after the

cover is removed.

A. O-ring cover

B. O-rings

The water filter compartment is located in the right-hand side

of the refrigerator ceiling. Push up on the compartment door

to release the catch, then lower the door.

Align the arrow on the water filter label with the cutout notch in

the filter housing and insert the filter into the housing.

Turn the filter clockwise 90 degrees (1/4turn), until it locks into

the housing.

NOTE: If the filter is not correctly locked into the housing, the

water dispenser will not operate. Water will not flow from the

dispenser.

While the compartment door is still open, lift the filter up into

the compartment. Then, close the filter compartment door

completely.

Flush the water system. See "Flushing the Water Filter" in the

"Water and Ice Dispensers" section.

IMPORTANT: If you do not flush the water system, you may

experience dripping and/or decreased flow from the water

dispenser.

The Water Filter Status Light

Press OPTIONS on the control panel to launch the Options menu.

Press OPTIONS, under Filter Status, again to display the

percentage of filter life remaining (from 99% to 0%). Press ICE/

WATER, under Back, to return to the Normal screen.

The water filter status lights will help you know when to change

your water filter.

• ORDER FILTER (yellow) - it is almost time to change the water

filter. While you are dispensing water, "Order Filter" will blink

seven times and sound an alert tone three times.

REPLACE FILTER (red) - Replace the water filter. While you are

dispensing water, "Replace Filter" will blink seven times and

an alert tone will sound three times.

RESET the water filter status tracking feature. After you

replace the disposable filter with a new filter, closing the filter

compartment door will automatically reset the filter status

tracking feature. See "Using the Control(s)."

NOTE: "REPLACE FILTER" will remain illuminated if a filter is

not installed or is installed incorrectly.

Replace the Water Filter

To purchase a replacement water filter, see "Accessories" in the

User Guide, Use and Care Guide or User Instructions.

Replace the disposable water filter when indicated on the water

filter status display or at least every 6 months. If water flow to your

dispenser or ice maker decreases noticeably, change the water

filter sooner.

1. Locate the water filter compartment in the right-hand side of

the refrigerator ceiling. Push up to release and lower the

compartment door.

2. Turn the water filter counterclockwise (to the left), and pull it

straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

3. Install the replacement water filter by following steps 2

through 7 in the "Install the Water Filter" section.

An air filter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use.

Installing the Air Filter

Install the air filter behind the vented door, located on the rear wall

near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

A. Air filter

Installing the Filter Status Indicator

The filter comes with a status indicator, which should be activated

and installed at the same time the air filter is installed.

Models with notches:

With the indicator screen facing outward, slide the

indicator down into the notches.

NOTE: The indicator will not easily slide into the notches

if the bubble has not been popped.

Close the air filter door, and check that the indicator is

visible through the window in the door.

A. Status indicator window

B. Air filter status indicator

C. Notches

Models without notches:

• Place the indicator somewhere it is easily visible - either

inside the refrigerator, or elsewhere in your kitchen or

home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when

the status indicator has completely changed from white to red.

To order a replacement air filter, contact us. See "Accessories" in

the User Guide, Use and Care Guide or User Instructions for

information on ordering.

1. Remove the used air filter by squeezing in on the side tabs.

2. Remove the used status indicator.

3. Install the new air filter and filter status indicator using the

instructions in the previous sections.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are

notches behind the door.

REFRIGERATORUSE

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

Exterior Cleaning

Please see the exterior cleaning information specific to your

model.

Style I - Smooth Door

IMPORTANT: Damage to smooth finish due to improper use of

cleaning products, or using non-recommended cleaning

products, is not covered under the warranty. Sharp or blunt

instruments will mar the finish.

DO USE DO NOT USE

Soft, clean cloth X Abrasive cloths

X Paper towels or newsprint

X Steel-wool pads

Warm, soapy water - X Abrasive powders or liquids

use a mild detergent X Window sprays

X Ammonia

X Acidic or vinegar based

cleaners

X Oven cleaners

X Flammable fluids

NOTE: Paper towels scratch and may dull the clear coat of the

painted door. To avoid possible damage use only soft clean

clothes to polish and wipe the door.

Style 2 - Stainless Steel

IMPORTANT:

• Damage to stainless steel finish due to improper use of

cleaning products, or using non-recommended cleaning

products, is not covered under the warranty.

DO USE DO NOT USE

Soft, clean cloth X Abrasive cloths

X Paper towels or newsprint

X Steel-wool pads

Warm, soapy water X Abrasive powders or liquids

X Ammonia

X Citrus-based cleaners

X Acidic or vinegar-based

cleaners

X Oven cleaners

For heavy soil, ONLY

a stainless steel

cleaner designed for

appliances. To order

the cleaner, see

"Accessories."

Stainless steel cleaner is for

stainless steel parts only! Do

not allow the Stainless Steel

Cleaner and Polish to come

into contact with any plastic

parts such as the trim pieces,

dispenser covers or door

gaskets.

NOTES:

• If unintentional contact does occur, clean plastic part with a

sponge and mild detergent in warm water. Dry thoroughly with

a soft cloth.

Just because a cleaner is a liquid does not mean it is

nonabrasive. Many liquid cleansers formulated to be gentle on

tile and smooth surfaces still damage stainless steel.

Citric acid permanently discolors stainless steel. To avoid

damaging the finish of your stainless steel refrigerator:

Do not allow these substances to remain on the finish

X Mustard X Citrus-based sauces

X Tomato juice X Citrus-based products

X Marinara sauce

Interior Cleaning

Unplug refrigerator or disconnect power.

Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets.

3. Plug in refrigerator or reconnect power.

Condenser Cleaning

There is no need for routine condenser cleaning in normal home

operating environments. If the environment is particularly greasy

or dusty, or there is significant pet traffic in the home, the

condenser should be cleaned every 2 to 3 months to ensure

maximum efficiency.

If you need to clean the condenser:

1. Unplug refrigerator or disconnect power.

2. Remove the base grille.

3. Use a vacuum cleaner with a soft brush to clean the grille, the

open areas behind the grille and the front surface area of the

condenser.

4. Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

The lights in both the refrigerator and freezer compartments are

LEDs which do not need to be replaced. If the lights do not

illuminate when the door or drawer is opened, call for assistance

or service. In the U.S.A., call 1-800-253-1301. In Canada call

1-800-807-6777.

Vacations

If You Choose to Leave the Refrigerator On While You're

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm to

OFF (up) position, or press the switch to OFE

4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or press the switch to OFF,

depending on your model.

3. Turn off the Temperature control(s). See "Using the Control(s)."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or press the switch to OFF,

depending on your model.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See "Using the Control(s)."

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily OR raise the leveling screws so they don't

scrape the floor. See "Adjust the Door(s)."

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

PROBLEMSOLVER

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator

will not operate

Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

No power to the electrical outlet -Plug in a lamp to see if the outlet is working.

Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit

breaker. If the problem continues, contact a licensed electrician.

Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on.

See "Using the Controls" in the User Instructions or User Guide.

New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment

(refrigerator or freezer) more quickly.

Refrigerator control is in Showroom mode (on some models)- If the refrigerator is in Showroom

mode, cooling will be off and "Showroom" will be illuminated on the control panel. See "Using the

Controls" in the User Instructions or User Guide for more information.

Motor seems to

run too much

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than you're

used to, because the compressor and fans operate at lower speeds that are more energy-efficient.

This is normal.

NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added, the

doors are opened often, or if a door has been left open.

Lights do not work Your refrigerator has been equipped with LED lighting which does not need to be replaced - If

there is power to the refrigerator and the lights do not illuminate when a door or drawer is opened,

call for service or assistance. See the Warranty (in the User Instructions or User Guide) for contact

information.

The dispenser light is set to OFF - On some models, the dispenser light will operate only when the

dispenser paddle is pressed. If you want the dispenser light to stay on continuously, see "Water and

Ice Dispensers" in the User Instructions or User Guide).

Doors have been open longer than 10 minutes - Close the doors and drawers to reset, and open

to resume lighted task.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Exterior drawer control •

not lit/unresponsive

The refrigerator is in Cooling Off mode - Exit Cooling Off mode. See "Using the Control(s)" inthe

User Instructions or User Guide.

The refrigerator controls' initialization process did not complete successfully - Unplug the

refrigerator, wait 5 seconds. Plug in the refrigerator, and wait 30 seconds before opening the doors

or drawers, or touching the control panel.

The drawer front was recently removed - Make sure the temperature control wires have been

properly reconnected. See "Remove and Replace Drawer Fronts."

Refrigerator

seems noisy

The compressor in your new refrigerator regulates temperature more efficiently and uses less energy

than older models. During various stages of operation, you may hear normal operating sounds that are

unfamiliar.

The following noises are normal:

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice

maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not

connected to a water line, turn off the ice maker.

• Repetitive Clicking - Dual evaporator valve regulating the cooling operation.

• Cracking/Clatter - Heard when ice is ejected from the ice maker mold and then falls into the ice

storage bin.

• Popping - Heard when the inside walls contract/expand, especially during initial cool-down.

• Hissing/Dripping - Flow of refrigerant, or flow of oil in the compressor.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during

normal operation.

• Rattling - Heard when water passes through the water line, or due to the flow of refrigerant. Rattling

may also come from items placed on top of the refrigerator.

• Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into the

drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

• Vibration - The refrigerator may not be steady. Adjust the leveling screws and lower the leveling foot

until it is firmly against the floor. See "Refrigerator Leveling, Door Closing and Alignment."

Temperature

is too warm

New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment

(refrigerator or freezer) more quickly.

Cooling is turned off - Turn on cooling. See "Using the Controls" in the User Instructions or User

Guide.

• Doors are opened often or not closed completely - This allows warm air to enter the refrigerator.

Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Large amount of warm food recently added - Allow several hours for the refrigerator to return to

its normal temperature.

• Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder

setting. Check the temperature again in 24 hours.

Temperature is too cold

in the refrigerator/

crisper

Controls are not set correctly for the surrounding conditions - Adjust the controls to a warmer

setting. Check the temperature again in 24 hours.

Ice storage bin is not in the correct position - See "Ice Maker and Ice Storage Bin" in the User

Instructions or User Guide.

Air vents are blocked - Remove items that are immediately in front of the vents.

Temperature is too

warm/cold in the

exterior drawer

• Control is not set correctly for the items stored in the drawer - Adjust the temperature setting.

See "Temperature Controlled Exterior Drawer" in the User Instructions or User Guide.

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

• Room is humid - A humid environment contributes to moisture buildup. Only use the refrigerator in

an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the refrigerator.

Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Frost/Ice buildup in the

freezer compartment

The drawer is opened often or left open -Minimize drawer openings and close drawer completely

after use.

Poor drawer seal - Ensure drawer seal is making full contact with the cabinet to allow for an

adequate seal.

Temperature control(s) are not set correctly- See "Using the Controls" (in the User Instructions or

User Guide) for recommended temperature settings.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm

water. Rinse and dry with a soft cloth.

Doors will not

close completely

• Door is blocked open - Move food packages away from the door. Make sure all bins and

shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See "Refrigerator Leveling,

Door Closing and Alignment."

Refrigerator unsteady or it

rolls forward when opening

and closing doors or

drawers

• Refrigerator brake feet are not snug against the floor - Remove the base grille. Turn both

brake feet (one on each side) clockwise, the same amount, until they are snug against the floor.

See "Refrigerator Leveling, Door Closing and Alignment."

ICE AND WATER

Ice maker is not •

producing ice,

not producing

enough ice,

or producing •

small/hollow ice

Ice/Water dispenser

will not operate

properly

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

Possible Causes and/or Recommended Solutions

Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully

turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is

fully open.

Kink in the water source line - A kink in the water line can reduce water flow, resulting indecreased ice

production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the water line.

Ice maker is not turned on - Turn on the ice maker. See "Ice Maker and Storage Bin" in the User

Instructions or User Guide.

New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers" in the User Instructions or User Guide) Wait 24 hours for ice production

to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Refrigerator door is not closed completely - Close the door firmly. If itdoes not close completely, see

"The doors will not close completely."

A water filter is installed on the refrigerator - Remove the water filter and operate the ice maker. If ice

volume improves, then the filter may be clogged or incorrectly installed. Replace filter or install it

correctly.

Large amount of ice was recently removed - Allow sufficient time for the ice maker to produce

more ice.

• Ice is jammed in the ice maker ejector arm - Remove ice from the ejector arm using a plastic utensil.

• Inadequate water pressure - Verify that the household has adequate water pressure. See "Water

Supply Requirements."

• Water filter is installed incorrectly - Make sure the filter is properly installed. See "Water Filtration

System" in the User Instructions or User Guide.

• A reverse osmosis water filtration system is connected to your cold water supply - This can

decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

New installation - After connecting the refrigerator to a water source, flush the water system.

(See "Water and Ice Dispensers" in the User Instructions or User Guide) Wait 24 hours for ice production

to begin. Wait 72 hours for full ice production. Discard the first three batches of ice produced.

Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make sure

the ice storage bin is firmly in position. See "Ice Maker and Storage Bin" in the User Instructions or User

Guide.

Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery

chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery

chute and the bottom of the ice storage bin using awarm damp cloth, then dry both thoroughly. To avoid

clogging and to maintain afresh supply of ice, empty the storage bin and clean both the storage bin and

the delivery chute every 2 weeks.

Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers" in the User Instructions or

User Guide.

Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door,

temporarily switch from crushed ice to cubed ice to clear the jam.

Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few

minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the

ice bin, not through the dispenser.

Water pressure to the home is not at or above 35 psi (241 kPa) - The water pressure to the home

affects the flow from the dispenser. See "Water Supply Requirements."

Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water

Filtration System" in the User Instructions or User Guide.

La page charge ...

Jenn-Air MFX2876DRH00 Guide d'installation

Marque: Jenn-Air

Modèle: MFX2876DRH00

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air MFX2876DRH00 Installation guide

Jenn-Air MFX2876DRH00 Guide d'installation

Ce manuel convient également à

Jenn-Air MFX2876DRH00 Guide d'installation

dans d''autres langues

Autres documents