Panasonic WH-MHF09G3E5 Le manuel du propriétaire

Português Nederlands Italiano Deutsch Español Français English

F569818

Operating Instructions

(Mono bloc)

Air-to-Water Heatpump

Operating Instructions

(Mono bloc) Air-to-Water Heatpump

2-15

Installation Instructions attached.

Mode d’emploi

Pompe à chaleur air-eau (Mono bloc)

16-29

Consignes d’installation jointes.

Instrucciones de funcionamiento

Bomba de calor de aire a agua (Mono bloc)

30-43

Instrucciones de instalación adjuntas.

Bedienungsanleitung

(Kompaktgerät) Luft/Wasser-Wärmepumpe

44-57

Installationsanleitung liegt bei.

Istruzioni operative

Pompa di calore Aria-acqua (Mono bloc)

58-71

Istruzioni per l’installazione allegate.

Gebruiksaanwijzing

(Mono bloc) Air-to-Water Warmtepomp

72-85

De instructies voor installatie zijn bijgevoegd.

Instruções de funcionamento

Bomba de Calor Ar-Água (Mono bloco)

86-99

Instruções de instalação anexadas.

Model No.

Mono bloc Unit

WH-MHF09G3E5

WH-MHF12G6E5

2

Thank you for purchasing Panasonic

product.

Before operating the system, read these

operating instructions thoroughly and keep them

for future reference.

Table of contents

Safety precautions ……………………………3-5

To adjust initial settings ………………………6-7

How to use ………………………………… 8-12

Maintenance …………………………………… 12

Troubleshooting ……………………………13-14

Information …………………………………… 15

Air-to-Water

Heatpump

(mono-bloc unit)

Power Supply

Solar Panel

Radiator

Shower

Fan Coil Unit

Floor

Heating

Water Tank Unit

Remote Control

Before use, make sure the system

has been installed correctly by an

authorised dealer according to the

given instructions.

• Panasonic (Mono bloc) Air-to-Water Heatpump is designed to

operate with Panasonic Water Tank Unit. Unless used together

with the Panasonic Water Tank Unit, Panasonic does not

guarantee any normal operation nor the reliability of the system.

• These operating instructions describe how to operate the system

using the mono bloc unit.

• As for the operation of other products such as water tank,

radiator, external thermo controller, and underfloor units, refer to

the operating instructions of each product.

• Some functions described in this manual may not be applicable

to your system.

• Consult your nearest authorised dealer for further information.

The illustrations in this manual are for explanation purposes only and may differ from the actual unit.

They are subject to change without notice for future improvement.

Operating conditions

HEATING

Water outlet temperature (°C)

(Min. / Max.)

25 / 65

Outdoor ambient temperature (°C)

(Min. / Max.)

-20 / 35

When the outdoor temperature is out of the

range in the table, the heating capacity will drop

significantly and the mono bloc unit may stop

operating for its protection.

The unit will restart automatically after the outdoor

temperature returns to the specified range.

System overview

3

To prevent personal injury, injury to

others or property damage, please

comply with the following:

Incorrect operation due to failure to

follow instructions below may cause

harm or damage, the seriousness of

which is classified as below:

WARNING

This sign warns of

death or serious

injury.

CAUTION

This sign warns of

injury or damage

to property.

The instructions to be followed are

classified by the following symbols:

This symbol denotes

an action that is

PROHIBITED.

These symbols denote

actions COMPULSORY.

WARNING

Mono bloc unit

This appliance may be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved. Children

shall not play with the appliance.

Cleaning and user maintenance

shall not be made by children

without supervision.

Please consult an authorised

dealer or specialist to clean the

internal parts, repair, install,

remove and reinstall the unit.

Improper installation and

handling will cause leakage,

electric shock or fire.

Confirm with an authorised

dealer or specialist on usage of

any specified refrigerant type.

Using refrigerant type other than

the specified may cause product

damage, burst and injury etc.

Do not install the unit in

a potentially explosive or

flammable atmosphere. Failure

to do so could result in fire.

Do not insert your fingers

or other objects into the

mono bloc unit; the rotating

parts may cause injury.

Safety precautions

EnglishSafety precautions

4

Do not touch the mono bloc unit

during lightning, it may cause an

electric shock.

Do not sit or step on the

unit, you may fall down

accidentally.

Power supply

Do not use a

modified cord, joint

cord, extension

cord or unspecified

cord to prevent

overheating and fire.

To prevent overheating, fire or

electric shock:

• Do not share the same power

outlet with other equipment.

• Do not operate with wet hands.

• Do not bend or twist power

supply cord.

If the supply cord is damaged,

it must be replaced by the

manufacturer, service agent or

similarly qualified persons in

order to avoid a hazard.

This unit is equipped with

Residue Current Circuit Breaker

(RCCB). Ask an authorised

dealer to check RCCB operation

regularly, especially after

installation, inspection, and

maintenance. RCCB malfunction

may result in electric shock and/

or fire.

It is strongly recommended that

Install Residual Current Device

(RCD) on-site to prevent electric

shock and/or fire.

Before obtaining access to

terminals, all supply circuits must

be disconnected.

Stop using the product if any

abnormality/failure occurs and

disconnect the power supply.

(Risk of smoke/fire/electric

shock)

Examples of abnormality/failure

• RCCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of

the unit is observed.

• Hot water leaks from the unit.

Contact your local dealer

immediately for maintenance/

repair.

Wear gloves during inspection

and maintenance.

This equipment must be earthed

to prevent electrical shock or fire.

Prevent electric shock by

disconnecting the power supply

before cleaning or servicing.

This appliance is for multiple

uses. To avoid electric shock,

burn and/or fatal injury, make

sure to disconnect all power

supplies before accessing any

terminal in the unit.

Safety precautions

5

CAUTION

Mono bloc unit

Do not wash the unit with water,

benzine, thinner or scouring

powder to avoid damage or

corrosion on the unit.

Do not install the unit close

to any combustibles or at

bathroom. Otherwise, it may

cause electric shock and/or fire.

Do not touch the water discharge

pipe of the unit during operation.

Do not place any material on the

unit or under it.

Do not touch the sharp

aluminium fin; sharp parts

may cause injury.

Do not use the system during

sterilisation in order to prevent

scalding with hot water, or

overheating of shower.

Prevent water leakage by

ensuring that the drainage pipe

is connected properly.

After a long period of use, make

sure the installation rack is not

deteriorated. The deteriorated

rack may cause the unit to fall

down.

Ask an authorised dealer

to determine the level of

sterilisation function field settings

according to the local laws and

regulations.

Remote control

Do not wet the remote control.

Failure to do so may result in

electric shock and/or fire.

Do not press the buttons on the

remote control using hard and

sharp objects. Failure to do so

may cause damage to the unit.

Do not wash the remote control

using water, benzine, thinner or

scouring powder.

Do not inspect or maintain the

remote control by yourself.

Consult an authorised dealer in

order to prevent personal injury

caused by incorrect operation.

EnglishSafety precautions

6

To adjust initial settings

Dealer

Select menus and determine settings according to the system available in the

household. It is recommended that all alterations of settings are done by an

authorised dealer or specialist.

• After initial installation, you may manually adjust the settings.

The initial setting remains active until the user changes it.

• The remote control can be used for multiple installations.

• Ensure the operation LED is OFF before setting.

• The system may not work properly if set wrongly. Please consult

an authorised dealer.

1

Press and simultaneously and hold for

5 seconds until the display shows SETTING STATUS.

2

Press

or to select the menu.

3

Press

to enter the menu.

4

Press or to select YES/NO, or other options.

YES: to enable the menu

NO: to disable the menu

5

Press

to confirm.

Remote Control

DisplayOperation LED

Menu (1 ~ 17)

Default

Setting

Setting Display

1

Room Thermostat Connection

To select whether or not to connect to the optional room

thermostat.

NO YES NO

2

Backup Heater Selection

To reduce the heater power if unnecessary.

*Options of kW vary depending on the model.

9 kW

*3 kW / 6 kW /

9 kW

3

Water System Freeze Prevention

To activate or deactivate the water freeze prevention when the

system is OFF.

YES YES NO

4

Tank Connection

To select whether or not to connect to the optional water tank unit.

Note: If NO is selected, menus 5 to 15 are skipped.

NO YES NO

5

Solar Priority

To select the use of solar panel for heating up the water tank.

NO YES NO

6

Heating Priority

To select the room heating as priority during HEAT + TANK mode.

Note: If YES is selected, menus 7 and 8 are skipped for HEAT +

TANK mode.

NO YES NO

7

Heating Operation Interval

To set the interval for HEAT mode during HEAT + TANK mode.

Note: If YES is selected in menu 6, this menu is skipped.

3 hours

0.5 hours ~

10 hours

8

Tank Heat-up Interval

To set the interval for the water tank during HEAT + TANK mode.

Note: If YES is selected in menu 6, this menu is skipped.

30 minutes

5 minutes ~

1 hour 35 minutes

7

9

Booster Heater

To activate or deactivate the water tank’s booster heater.

Note: If NO is selected, menu 10 is skipped.

YES YES NO

10

Booster Heater Delay Timer

To delay time for the booster heater to activate while the system is

heating up the water tank.

1 hour

20 minutes ~

1 hour 35 minutes

• Do not use the system during sterilisation in order to prevent scalding with hot water, or overheating of shower.

• Ask an authorised dealer to determine the level of sterilisation function field settings according to the local laws and

regulations.

11

Sterilisation

To sterilise the water tank, if required.

Note: If NO is selected, menus 12 to 14 are skipped.

YES YES NO

12

Sterilisation Day & Time

To set timer for sterilisation.

(Only once a week. Operates even under a standby condition)

Monday

12:00

Monday ~ Sunday

0:00 ~ 23:50

13

Sterilisation Temperature

To set the temperature of sterilisation.

70 °C 40 °C ~ 75 °C

14

Continuation of Sterilisation

To maintain heating temperature in order to complete the

sterilisation.

10 minutes

5 minutes ~

1 hour

15

Base Pan Heater

To select whether or not to connect to the optional base pan

heater.

Note: If NO is selected, menu 16 is skipped.

NO YES NO

16

Base Pan Heater type

Type A - The base pan heater activates only during deice

operation.

Type B - The base pan heater activates when outdoor ambient

temperature is 5 °C or lower.

AAB

17

Dry Concrete

During construction to dry the concrete under a preset

temperature.

Do not use this menu for any other purposes and in period other

than during construction (Refer to information page).

- 1 day ~ 99 days

User

Remote control preparation

1

Press

.

2

Press

or to set the current day.

3

Press to confirm.

4

Repeat steps

2

and

3

to set the current time.

■ Note:

• The current day and time need to be set in cases below:

- When the power is turned on for the first time.

- A long time has elapsed since the power was turned on the

last time.

• The current time that has been set will be the standard time for

all the timer operations.

Caution Indicator (Tank Temperature above 60 °C)

Dealer

Operation/settings to be done only by the authorised dealer/specialist.

User

Operation/settings to be done by the authorised dealer/specialist or user.

EnglishTo adjust initial settings

8

How to use

User

Enjoy quiet operation

Press .

• This operation reduces the noise of mono bloc unit.

The operation may cause heating ability to decrease.

User

System status check mode

1

Press

.

(The display shows STATUS.)

2

Press or to check the selected mode.

• Dry concrete (does not show during normal

operation)

• The Water Inlet Temperature

• Tank Temperature

• Compressor Running Frequency

• Error History

• Heat mode total power consumption (Up to 999 days)

• Tank mode total power consumption (Up to 999 days)

• Press to exit the STATUS mode.

■ Note:

• Once the STATUS mode is entered, the display

shows STATUS.

• The STATUS mode cannot be activated when the

display shows SETTING.

• The total power consumption is an estimated value

based on AC 230 V and may differ from value

measured by precise equipment.

■ Note: In normal operation, the , and buttons are not in use.

User

Turn on or off the system

Press .

When the system is ON, the operation LED is lit and the

actual water outlet temperature and outdoor ambient

temperature are shown on the display.

User

Select operation mode

Press to select operation mode.

HEAT

• The panel/floor HEAT operation is either

turned ON or OFF.

• The mono bloc unit provides heat to the

system.

HEAT

+ TANK

• The mono bloc unit provides heat to the

sanitary water tank and the system.

• This mode can be selected only when the

sanitary water tank is installed.

TANK • The sanitary water tank is either turned

ON or OFF.

• The mono bloc unit provides heat to the

sanitary water tank.

User

Initiate the backup heater

Press

.

• The backup heater provides extra heat at low outdoor

temperature. The backup heater is possible only in the

heat mode.

• Once the backup heater is set, it is automatically

operated when conditions are fulfilled.

• To disable the backup heater, press

again.

The system is turned off by an external switch.

9

Dealer

Operation/settings to be done only by the authorised dealer/specialist.

User

Operation/settings to be done by the authorised dealer/specialist or user.

Dealer

System temperature setting

Temperature setting Display

The system controls the temperature for each menu based on the

outdoor ambient temperature.

• To set or change the temperatures, make sure to contact your

nearest authorised dealer.

1

Press and hold for 5 seconds to enter the

temperature range setting mode.

(The display shows SETTING.)

2

Press

or to select a menu.

3

Press to enter the menu.

4

Press or to set the desired temperature.

5

Press

to confirm the setting.

• Repeat steps

2

to

5

to set other menus.

User

Checking the temperature range

1

Press and hold

for 5 seconds to enter the temperature range setting mode.

2

Press

or to select a menu.

• Press

to exit.

Menu

Default

setting

Temperature

setting

Display

Setting of low outdoor ambient temperature. -5 °C -15 °C ~ 15 °C

HEAT

Setting of high outdoor ambient temperature. 15 °C -15 °C ~ 15 °C

Setting of water outlet temperature at low outdoor

ambient temperature.

55 °C 25 °C ~ 65 °C

Setting of water outlet temperature at high outdoor

ambient temperature.

35 °C 25 °C ~ 65 °C

During HEAT mode, the water

outlet temperature is adjusted as

is shown the diagram on the right.

It is performed within the preset

temperature range.

<Water outlet

temperature>

max. water temp.

min. water temp.

Setting of outdoor ambient temperature to turn

OFF heating operation during HEAT mode.

24 °C 5 °C ~ 35 °C

HEAT

Setting of outdoor ambient temperature to turn ON

the backup heater.

0 °C -15 °C ~ 20 °C

HEATER

Setting of sanitary water tank temperature. 52 °C 40 °C ~ 75 °C

TANK

EnglishHow to use

10

How to use

User

Shifting the water temperature

Desired temperature setting

This easily shifts the water outlet temperature if the setting is

undesirable.

1

Press

to enter the water temperature shifting mode.

2

Press

to change setting.

3

Press

or to set the desired temperature.

(temperature range: -5 °C ~ 5 °C)

Temperature setting

+5

-5

Shift value

<Water outlet

temperature>

4

Press to confirm the setting.

■ Note:

• Press or wait for 30 seconds to exit the SETTING mode.

• The set temperature will be saved in the system once confirmed.

• The SETTING mode cannot be activated when the SERVICE and STATUS indicators are ON.

• The system will shift the temperature within water outlet temperature range.

User

Holiday mode

• By setting the day (s) in holiday mode, it promotes energy saving

while you are on holiday, and enables the system to resume at the

preset temperature after your holiday.

• Ensure that the system is OFF before setting.

• The system will resume operation automatically at 00:00 am after

the holiday.

• The day the HOLIDAY mode was set is counted as day 1.

Desired days

Example:

Setting the holiday mode on June 21, 08:00 am. By setting 3 days,

the system resumes operation on June 24, 00:00 am.

1

Press

to enter the HOLIDAY mode.

2

Press

or to set the desired days.

(Setting range: 1 day ~ 999 days)

3

Press to confirm the setting.

■ Note:

• Press or wait 30 seconds to exit the HOLIDAY mode.

11

User

Weekly timer setting

Promotes energy saving by allowing you to set up to 6

programmes in any given day.

Indicates the next timer operation

programme

Day to be selected

Indicates the next timer

operation day

Programme number in a day

OFF Timer

ON Timer

Lights up if Timer operation is selected

1

Press

to enter the timer setting mode.

2

Press

or to select your desired day.

3

Press to confirm your selection.

4

“1” will be blinking, press

to set

programme 1.

5

Press

to select ON or OFF timer.

6

Press or to select your desired time.

You can set , , and the Water

Temperature Thermo Shift setting.

7

Press

to confirm programme 1. The selected

day will be highlighted with ▼.

• After 2 seconds, the display will move to the next

programme. Repeat steps

4

to

7

to set

programmes 2 to 6.

• During timer setup, if no button is pressed within

30 seconds, or if the

is pressed, the setting at

that moment is confirmed and timer setup is ended.

To check current timer programme

1

Press to enter timer mode and press

to enter day setting.

2

Press

or until your desired day is shown,

press to confirm your selection.

3

Press

or to check the set programmes.

To modify current timer programme

or add new timer programme

1

Perform steps

1

to

7

of “Weekly timer

setting” to modify existing timer programme, or

add any timer programme.

To cancel current timer programme

1

Press to enter day.

2

Press

or until your desired day is shown,

press to enter programme setting.

3

Press

or until your desired programme is

shown.

Press to cancel the programme and ▼ will

disappear.

To disable/enable Weekly Timer

• To disable weekly timer setting, press , then

press .

• To enable previous weekly timer setting, press ,

then press .

Dealer

Operation/settings to be done only by the authorised dealer/specialist.

User

Operation/settings to be done by the authorised dealer/specialist or user.

EnglishHow to use

12

Mono bloc Unit

In case of a power supply failure or pump operating failure, drain the system (as suggested in the figure below).

H

<H

When water is idle inside the system, freezing up is very likely to happen which could

damage the system.

• Do not obstruct the air inlet and air outlet vents, it may cause low performance or

breakdown. Please remove obstacles to assure the ventilation.

• During winter, please clean and remove the snow near mono bloc unit so that the snow

does not cover the air inlet and air outlet vents.

External filter

• Clean the external filter at least once a year. Failure to do so may cause the filter to clog up, which may lead to system

breakdown. Consult an authorised dealer.

Inspection

• In order to ensure optimal performance of the units,

seasonal inspections on the units, external filter and field

wiring have to be carried out at regular intervals. Consult

an authorised dealer about maintenance.

• Clear any obstruction on the air inlet and outlet vents of

the mono bloc unit.

For extended non-use

• Do not switch off the power supply. Switching off the

power supply will stop the automatic water pump

operation and will cause jamming in the water pump.

Non serviceable criteria

Disconnect the power supply

then please consult an authorised dealer under the

following conditions:

• Abnormal noise during operation.

• Water/foreign particles have entered the remote control.

• Circuit breaker switches off frequently.

• Power cord becomes unnaturally warm.

Maintenance

Weekly timer setting

■ Note:

• You may set the timer for each day of the week (Monday to Sunday) with 6 programmes per day.

• When the system is switched on by the timer, it will use the previously set temperature to control the water outlet

temperature.

• The same timer programme cannot be set on the same day.

• You may also select 2 or more days with the same timer setting.

How to use

13

The following symptoms do not indicate malfunction.

Symptom Cause

Water flowing sound during operation. • Refrigerant flow inside the unit.

Operation is delayed a few minutes

after restarting.

• The delay is a protection for the compressor.

Mono bloc unit emits water/steam. • Condensation or evaporation occurring in the pipes.

Steam comes out of the mono bloc

unit in the heating mode.

• It is caused by defrost operation in the heat exchanger.

Mono bloc unit does not operate. • It is caused by the protection control of the system when outdoor temperature is

out of the operating range.

System operation switches off. • It is caused by the protection control of the system. When the water inlet

temperature is lower than 10 °C, the compressor stops and the backup heater

power turns on.

System is hard to heat up. • When the panel and the floor are heated simultaneously, warm water temperature

may decrease, which may reduce the heating ability of the system.

• When the outdoor air temperature is low, the system may need longer time to heat

up.

• Discharge outlet or intake inlet in the mono bloc unit is blocked by some obstacle,

such as a pile of snow.

• When the preset water outlet temperature is low, the system may need longer time

to heat up.

System does not heat up instantly. • System will take some time to heat up the water if it starts to operate at cold water

temperature.

Backup heater is automatically turned

ON when it is disabled.

• It is caused by the protection control of the unit heat exchanger.

Operation starts automatically when the

timer is not set.

• Sterilisation timer has been set.

Display power consumption remains

as previous value.

• Memory is saved on hourly basis. If a power failure occurs, the data kept from last

hour will be displayed.

• Total power consumption has reached 999 days. Press

to reset the counter.

HEAT indicator blinks on the display. • System is performing deice operation.

Loud refrigerant noise continue for a

few minutes.

• It is caused by protection control during deice operation at outdoor ambient

temperature lower than -10°C.

Check the following before calling for servicing.

Symptom Check

Operation in HEAT mode is not

working efficiently.

• Set the temperature correctly.

• Close the panel heater valve.

• Clear any obstruction in the air inlet and air outlet vents of the mono bloc unit.

Noisy during operation. • Mono bloc unit has been installed at an incline.

• Close the cover properly.

System does not work. • Circuit breaker has tripped/activated.

Operation LED is not lit or nothing is

displayed on the remote control.

• Check that the power supply is working correctly, or that a power failure has not

occurred.

Troubleshooting

Force Heater Mode Button

• If a malfunction occurs in the system, the backup heater may be used to heat up the water.

Press to switch on the backup heater.

• Press

to switch off the backup heater.

• In the Force Heater mode, no other operation can be used.

• This feature is only available to certain error codes.

• Refer to dealer for more details.

EnglishHow to use / Maintenance / Troubleshooting

14

Troubleshooting

The operation LED blinks and error code appears on

the display.

• Disconnect the power supply, and report

the error code to an authorised dealer.

• The timer operation will be cancelled

when an error code is displayed.

Diagnostic

display

Abnormality or Protection

control works

H12

Capacity mismatch

H15

Abnormal compressor temperature

sensor

H20

Abnormal water pump

H23

Abnormal refrigerant 1 sensor

H27

Abnormal service valve

H42

Compressor low pressure protection

H62

Abnormal water flow

H63

Abnormal low pressure sensor

H64

Abnormal high pressure sensor

H65

Abnormal deice water circulation

H70

Abnormal back-up heater overload

protector

H72

Abnormal tank temperature sensor

H76

Remote control communication error

H90

Abnormal indoor / outdoor

communication

H91

Abnormal tank heater overload protector

H95

Abnormal voltage connection

H98

Outdoor high pressure protection

H99

Indoor heat exchanger freeze prevention

Diagnostic

display

Abnormality or Protection

control works

F12

Pressure switch activated

F14

Poor compressor rotation

F15

Abnormal outdoor fan motor lock

F16

Comprehensive current protection

F20

Compressor temperature overload

protection

F22

Transistor module temperature overload

protection

F23

DC peak abnormal of operation

F24

Abnormal Refrigerant cycle

F25

Abnormal in a

c

ooling / heating charge

F27

Abnormal pressure switch

F30

Abnormal water outlet sensor 2

F36

Abnormal outdoor air temperature

sensor

F37

Abnormal water inlet sensor

F40

Abnormal outdoor discharge sensor

F41

Abnormal power factor correction

F42

Abnormal outdoor heat exchanger

sensor

F43

Abnormal outdoor defrost sensor

F45

Abnormal water outlet sensor

F46

Abnormalities in outdoor current

transformer disconnection

F48

Abnormal evaporator outlet temperature

sensor

F49

Abnormal bypass outlet temperature

sensor

F95

Abnormal cooling high pressure

15

Information

Dry Concrete Function

• During construction to dry the concrete under a preset temperature.

1

Press

and simultaneously and hold for 5 seconds until the display shows “ ”.

2

Press

.

(The display shows “ ”.)

3

Press

to select day.

Press

or to set the desired temperature.

4

Press to confirm the selection.

5

Repeat step

3

and

4

to set other days and temperature.

• Press to exit.

Operation/settings to be done only by the authorised dealer/specialist.

To Reset the Remote Control to Default

Setting

1

Press , , continuously for 5 seconds. The

operation is off during this period.

2

The display shows “

, , ” for 2

seconds for confirmation. After 2 seconds, it goes to

normal display.

Information for Users on Collection and Disposal of Old Equipment

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points,

in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment which could otherwise arise from inappropriate waste

handling.

For more information about collection and recycling of old products, please contact your local municipality,

your waste disposal service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your

local authorities or dealer and ask for the correct method of disposal.

EnglishTroubleshooting / Information

Nous vous remercions d’avoir porté

votre choix sur un produit Panasonic.

Avant d’utiliser le système, lisez ce mode

d’emploi dans son intégralité et conservez-le

pour toute référence ultérieure.

Table des matières

Consignes de sécurité ……………………17-19

Réglage initial ………………………………20-21

Consignes d’utilisation ……………………22-26

Entretien ……………………………………… 26

Dépannage …………………………………27-28

Informations …………………………………… 29

16

Avant utilisation, assurez-vous que le

système a été installé correctement par

un revendeur agréé conformément aux

instructions fournies.

• Cette pompe à chaleur air-eau (mono bloc) Panasonic est

conçue pour fonctionner avec un réservoir d’eau Panasonic.

Si elle n’est pas utilisée avec un réservoir d’eau Panasonic, le

fonctionnement normal et la fiabilité du système ne sont pas

garantis par Panasonic.

• Ce mode d’emploi décrit comment utiliser le système avec l’unité

mono bloc.

• En ce qui concerne le fonctionnement d’autres produits, tels que

le réservoir d’eau, le radiateur, le contrôleur thermique externe

et les unités de chauffage au sol, consultez le mode d’emploi de

chaque produit.

• Il est possible que certaines fonctions décrites dans ce manuel

ne soient pas applicables à votre système.

• Consultez votre revendeur agréé le plus proche pour en savoir

plus.

Les illustrations de ce mode d’emploi sont fournies à titre d’exemple uniquement et peuvent présenter des différences

par rapport à l’appareil proprement dit.

Celles-ci peuvent être modifiées sans préavis à des fins d’amélioration.

Vue d'ensemble du système

Conditions d’utilisation

CHAUFFAGE

Température de sortie d’eau (°C)

(Min. / Max.)

25 / 65

Température ambiante extérieure (°C)

(Min. / Max.)

-20 / 35

Si la température extérieure sort de la plage

indiquée dans le tableau, la capacité thermique

chutera de façon importante et l’unité mono bloc

risque de s’arrêter pour sa propre protection.

L’unité redémarrera automatiquement une fois que

la température extérieure sera de nouveau dans la

plage spécifiée.

Panneau solaire

Radiateur

Douche

Ventilo-

convecteur

Chauffage

au sol

Réservoir d’eau

Pompe à chaleur

air-eau

(unité mono bloc)

Alimentation

Télécommande

17

Pour éviter des blessures corporelles

sur vous-même et sur les autres ou

des dégâts matériels, respectez les

instructions ci-dessous :

Tout dysfonctionnement dû au

non-respect des instructions peut

occasionner des nuisances ou des

dégâts dont la gravité est classée

comme décrit ci-après :

AVERTISSEMENT

Ce symbole

signale la

présence d’un

danger pouvant

provoquer des

blessures graves

ou mortelles.

ATTENTION

Ce symbole

signale la

présence d’un

danger pouvant

provoquer

des blessures

corporelles ou

des dégâts

matériels.

Les instructions à respecter sont

classées d’après les symboles

suivants :

Ce symbole désigne une

action INTERDITE.

Ces symboles

désignent des actions

OBLIGATOIRES.

AVERTISSEMENT

Unité mono bloc

Cet appareil peut être utilisé

par des enfants à partir de

8 ans et par des personnes aux

capacités physiques, sensorielles

ou mentales diminuées,

ou manquant d’expérience

ou de connaissances, si le

fonctionnement en toute sécurité

de l’appareil leur a été expliqué

et s’ils comprennent les dangers

impliqués. Les enfants ne doivent

pas jouer avec cet appareil. Le

nettoyage et l’entretien régulier

ne doivent pas être réalisés par

des enfants sans surveillance.

Veuillez consulter un revendeur

agréé ou un spécialiste pour le

nettoyage des pièces internes et

pour la réparation, l’installation,

le retrait et la réinstallation

de l’unité. Une installation et

une manipulation incorrectes

pourraient occasionner des fuites,

un choc électrique ou un incendie.

Validez auprès du revendeur

agréé ou du spécialiste l’usage

de tout type de réfrigérant

spécifié.

L’utilisation d’un type de

réfrigérant autre que celui

spécifié peut endommager

le produit ou provoquer des

explosions, des brûlures, etc.

N’installez pas l’appareil dans

une atmosphère potentiellement

explosive ou inflammable. Sinon,

il y a un risque d’incendie.

Consignes de sécurité

FrançaisConsignes de sécurité

18

N’insérez jamais vos doigts

ou des objets dans l’unité

mono bloc ; les parties

rotatives peuvent entraîner

des blessures.

Ne touchez pas l’unité mono

bloc au cours d’un orage, cela

pourrait provoquer un choc

électrique.

Ne vous asseyez pas et

ne montez pas sur l’unité,

vous risquez de tomber

accidentellement.

Alimentation

N’utilisez pas de

cordon modifié, de

raccords, de rallonge

ou de cordon non

spécifié afin d’éviter

une surchauffe et un

incendie.

Pour éviter une surchauffe, un

incendie ou un choc électrique :

• Ne partagez pas la prise

d’alimentation avec un autre

appareil.

• N’utilisez pas l’unité avec des

mains mouillées.

• Ne pliez ou ne tordez pas le

cordon d’alimentation.

Si le cordon d’alimentation

est endommagé, il doit être

remplacé par le fabriquant, un de

ses techniciens ou une personne

qui possède des qualifications

équivalentes afin d’éviter tout

risque.

Cette unité est équipée

d’un disjoncteur de courant

résiduel (RCCB). Demandez

à un revendeur agréé de

vérifier régulièrement le

fonctionnement du RCCB,

surtout après l’installation,

l’inspection ou l’entretien. Un

dysfonctionnement du RCCB

peut provoquer un choc

électrique et/ou un incendie.

Il est fortement conseillé

d’installer un dispositif à courant

résiduel (DCR) sur le site afin

d’éviter un choc électrique et/ou

un incendie.

Tous les circuits d’alimentation

doivent être débranchés avant

tout accès aux bornes.

Arrêtez d’utiliser le produit en

cas d’anomalie/défaillance

et débranchez l’alimentation.

(Risque de fumée / feu / choc

électrique)

Exemples d’anomalie ou défaillance

• Le RCCB se déclenche

souvent.

• Vous remarquez une odeur de

brûlé.

• Vous remarquez des bruits

anormaux ou des vibrations de

l’unité.

• De l’eau chaude fuit de l’unité.

Contactez immédiatement votre

revendeur local pour l’entretien/

réparation.

Portez des gants pendant

l’inspection et l’entretien.

Cet équipement doit être

raccordé à la terre afin d’éviter un

choc électrique ou un incendie.

Consignes de sécurité

19

Évitez tout choc électrique en

débranchant l’alimentation avant

le nettoyage ou l’entretien.

Cet appareil convient à de

multiples usages. Pour éviter

tout choc électrique, toute

brûlure et/ou blessure mortelle,

assurez-vous d’avoir débranché

toutes les alimentations avant

d’accéder aux bornes de l’unité.

ATTENTION

Unité mono bloc

Ne lavez pas l’unité à l’eau,

au benzène, au diluant ou à la

poudre à récurer afin d’éviter

tout endommagement ou toute

corrosion de l’unité.

N’installez pas l’unité à proximité

de combustible ou dans une

salle de bains. Sinon, il existe un

risque de choc électrique et/ou

d’incendie.

Ne touchez pas le tuyau

d’évacuation d’eau de l’unité

pendant le fonctionnement.

Ne placez rien sur ou sous

l’unité.

Ne touchez pas l’ailette en

aluminium, car ses arêtes

vives peuvent causer des

blessures.

N’utilisez pas le système pendant

la stérilisation afin d’éviter toute

brûlure avec l’eau chaude ou la

surchauffe de la douche.

Empêchez toute fuite d’eau

en vous assurant que le tuyau

de vidange est correctement

raccordé.

Après une longue période

d’utilisation, assurez-vous que le

support d’installation n’est pas

détérioré. Un support détérioré

peut entraîner la chute de l’unité.

Demandez à un revendeur agréé

de déterminer le niveau des

réglages sur site de la fonction

de stérilisation conformément

aux lois et réglementations

locales.

Télécommande

Ne mouillez pas la

télécommande. Cela pourrait

provoquer un choc électrique et/

ou un incendie.

N’appuyez pas sur les touches

de la télécommande à l’aide

d’objets durs et pointus. Cela

pourrait endommager l’unité.

Ne nettoyez pas la

télécommande avec de l’eau,

du benzène, du diluant ou de la

poudre à récurer.

N’inspectez pas et n’entretenez

pas la télécommande vous-

même. Consultez un revendeur

agréé afin d’éviter toute blessure

due à un fonctionnement

incorrect.

FrançaisConsignes de sécurité

20

Réglage initial

Revendeur

Sélectionnez les menus et déterminez les réglages en fonction du système

disponible dans le foyer. Il est recommandé que toutes les modifications de

réglage soient réalisées par un revendeur agréé ou un spécialiste.

• Après l’installation initiale, vous pouvez ajuster les réglages

manuellement. Le réglage initial reste actif jusqu’à sa

modification par l’utilisateur.

• La télécommande peut être utilisée pour plusieurs installations.

• Assurez-vous que la DEL de fonctionnement est éteinte (OFF)

avant de réaliser le réglage.

• Le système peut ne pas fonctionner correctement s’il est mal

réglé. Veuillez consulter un revendeur agréé.

1

Appuyez sur et simultanément pendant 5 secondes,

jusqu'à ce que SETTING STATUS s'affiche à l'écran.

2

Appuyez sur

ou pour sélectionner le menu.

3

Appuyez sur pour entrer dans le menu.

4

Appuyez sur ou pour sélectionner YES/NO, ou

d’autres options.

YES : pour activer le menu

NO : pour désactiver le menu

5

Appuyez sur

pour valider.

Télécommande

AffichageDEL de fonctionnement

Menu (1 ~ 17)

Réglage

par défaut

Réglage Affichage

1

Raccordement du thermostat de la pièce

Pour sélectionner si le thermostat de la pièce en option est raccordé ou

non.

NO YES NO

2

Sélection du chauffage de secours

Pour réduire la puissance du chauffage, le cas échéant.

*Les valeurs en kW disponibles dépendent du modèle.

9 kW

*3 kW / 6 kW /

9 kW

3

Prévention du gel du circuit d'eau

Pour activer ou désactiver la prévention du gel du circuit d’eau lorsque le

système est à l’ARRÊT.

YES YES NO

4

Raccordement du réservoir

Pour sélectionner si le réservoir d’eau en option est raccordé ou non.

Remarque : Si NO est sélectionné, les menus 5 à 15 sont ignorés.

NO YES NO

5

Priorité au solaire

Pour sélectionner l’utilisation du panneau solaire pour le chauffage du

réservoir d’eau.

NO YES NO

6

Priorité au chauffage

Pour sélectionner le chauffage de la pièce comme priorité en mode

CHAUFFAGE + RÉSERVOIR.

Remarque : Si YES est sélectionné, les menus 7 et 8 sont ignorés pour le

mode CHAUFFAGE + RÉSERVOIR.

NO YES NO

7

Intervalle de fonctionnement du chauffage

Pour régler l’intervalle pour le mode CHAUFFAGE pendant le mode

CHAUFFAGE + RÉSERVOIR.

Remarque : Si YES est sélectionné dans le menu 6, ce menu est ignoré.

3 heures

0,5 heure ~

10 heures

8

Intervalle de chauffage du réservoir

Pour régler l’intervalle pour le réservoir d’eau pendant le mode

CHAUFFAGE + RÉSERVOIR.

Remarque : Si YES est sélectionné dans le menu 6, ce menu est ignoré.

30 minutes

5 minutes ~

1 heure 35 minutes

La page charge ...

Panasonic WH-MHF09G3E5 Le manuel du propriétaire

Ce manuel convient également à

Panasonic WH-MHF09G3E5 Le manuel du propriétaire

dans d''autres langues

Documents connexes