Simplicity 040381-01 Guide d'installation

GE Home Generator Systems

Home Generator System

Installation and

Start-Up Manual

is a trademark of General Electric Company

and is under license by Briggs & Stratton

Power Products Group, LLC.

reproduced or transmitted in any form without the express written

permission of Briggs & Stratton Power Products Group, LLC.

314669 Revision F

2

DATE OF PURCHASE

GENERATOR

Model Number

Model Revision

Serial Number

ENGINE

Thank you for purchasing this quality-built GE home generator. We’re pleased that you’ve placed your confidence in the GE

brand. When operated and maintained according to the instructions in the operator’s manual, your home generator will provide

many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby generators and

how to avoid them. This product is only for use as an optional generator system which provides an alternate source of electric

power and to serve loads such as heating, refrigeration systems, and communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

Save these original instructions for future reference.

This generator requires professional installation before use. The installer should follow the instructions completely.

Where to Find Us

You never have to look far to find support and service for your generator. For quick service when you need it most fill out the

information below and keep your original receipt with this manual. You may contact Customer Service at (888) 575-8226, or

click on SERVICE & SUPPORT at www.homestandbygeneratorsystems.com, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

3

Table of Contents

Safety Rules.....................................................4

Installation .....................................................7

Home Owner Responsibilities......................................................7

Installing Dealer/Contractor Responsibilities .......................................7

Cold Weather Kit..................................................................8

Unpacking Precautions ...........................................................8

Delivery Inspection................................................................8

Shipment Contents ...............................................................8

Installation Checklist - GE Home Generator Systems................................9

Generator Placement ............................................................11

Placement of Standby Generator to REDUCE THE RISK OF CARBON MONOXIDE POISONING 12

Placement of Standby Generator to REDUCE THE RISK OF FIRE.....................14

National Fire Protection Association (NFPA) Standard NFPA 37 Requirements and Testing 16

Electrical and Fuel Inlet Locations ................................................17

Lifting the Generator.............................................................18

Concrete Anchoring of Unit.......................................................18

Access Panels ...................................................................19

The Gaseous Fuel System ........................................................21

Fuel Factors .....................................................................22

System Connectors ..............................................................25

Generator AC Connection System ................................................26

Grounding the Generator.........................................................26

Power Connections from Generator to Transfer Switch ............................27

System Control Board............................................................28

Menu ...........................................................................29

General Set Up Screen ...........................................................30

Control Panel Prompts ...........................................................31

Advanced Settings Screen........................................................32

Service Code Detection System...................................................33

Final Installation Considerations ..................................................33

Initial Start-up (No Load) .........................................................34

Electronic Governor System ......................................................35

Operation..................................................... 36

Automatic Operation Sequence ..................................................36

Setting Exercise Timer............................................................36

Wireless Monitor.................................................................38

Schematic / Wiring Diagrams ....................................................41

4

Safety Rules

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a degree

or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard. The signal word NOTICE is

used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Important Safety Instructions

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

WARNING The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Smoke alarms cannot detect carbon

monoxide gas.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator system unsafe.

5

WARNING Storage batteries give off explosive hydrogen gas

during recharging.Slightest spark will

ignite hydrogen and cause explosion,

resulting in death, serious injury and/

or property damage.Battery electrolyte fluid contains acid and

is extremely caustic.Contact with battery contents could cause

severe chemical burns.A battery presents a risk of electrical shock

and high short circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit cigarette during

and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death, serious injury and/or

property damage.

• Install the fuel supply system according to NFPA 37 and other

applicable fuel-gas codes.

• Before placing the generator into service, the fuel system lines

must be properly purged and leak tested.

• After the generator is installed, you should inspect the fuel

system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or other

explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment. Keep the area near the generator clean

and free of debris.

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from utility

power could result in death or serious injury to electric utility

workers due to backfeed of electrical energy.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce the risk of a shock hazard.

• DO NOT allow unqualified persons or children to operate or

service generator.

• In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

• Despite the safe design of the residential generator, operating

this equipment imprudently, neglecting its maintenance or being

careless could cause possible injury or death.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• Before performing any maintenance on the generator, disconnect

the battery cable indicated by a NEGATIVE, NEG or (-) first. When

finished, reconnect that cable last.

• After your system is installed, the generator may crank and start

without warning any time there is a power failure. To prevent

possible injury, always set the generator’s system switch to OFF,

remove the service disconnect from the disconnect box AND

remove the 15 Amp fuse BEFORE working on the equipment.

WARNING Hazardous Voltage - Contact with power lines could

cause electric shock or burn, resulting in death or

serious injury.Lifting Hazard / Heavy Object - Could

result in serious injury.

• If lifting or hoisting equipment is used, DO NOT contact any

power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the Generator.

• DO NOT lift unit by roof as damage to generator will occur.

6

WARNING Starter and other rotating parts could entangle

hands, hair, clothing, or accessories resulting in

serious injury.

• NEVER operate generator without protective housings, covers, or

guards in place.

• DO NOT wear loose clothing, jewelry or anything that could be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control panel and

disconnect Negative (NEG or -) battery cable.

CAUTION Installing the 15A fuse could cause the engine

to start at any time without warning resulting in minor or

moderate injury.

• Observe that the 15 Amp fuse has been removed from the control

panel for shipping.

• DO NOT install this fuse until all plumbing and wiring has been

completed and inspected.

CAUTION Excessively high operating speeds could result in

minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on generator.

• DO NOT tamper with governed speed. Generator supplies correct

rated frequency and voltage when running at governed speed.

• DO NOT modify generator in any way.

NOTICE Improper treatment of generator could damage it and

shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating air is

critical for correct generator operation.

• The access panels/door must be installed whenever the unit

is running.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step. Stepping

on the unit could cause stress and break parts. This may result in

dangerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator and contanct an authorized deaker if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively;

-unit makes unusual noises.

WARNING

Exhaust heat/gases could ignite combustibles

or structures resulting in death, serious injury

and/or property damage. Contact with muffler

area could cause burns resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must have

at least 5 ft. (1.5 m) minimum clearance from any structure,

shurbs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft. (1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have

a minimum of 5 ft. (1.5 m) overhead clearance from any

structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck or

other type of structure that may confine airflow.

• Use only flexible steel fuel line provided. Connect provided

fuel line to generator, DO NOT use with or substitute any

other flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot detect

smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generator cooling

and maintenance clearances.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other

states or federal jurisdictions may have similar laws.

Contact Briggs and Stratton, retailer, or dealer to obtain a

spark arrester designed for the exhaust system installed on

this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

7

• Read and follow the instructions given in the

operator’s manual.

• Follow a regular schedule in maintaining, caring for

and using your home generator, as specified in the

operator’s manual.

Home Owner Responsibilities

• Read and observe the safety rules.

• Install only an UL approved transfer switch that is

compatible with the generator.

• Read and follow the instructions given in this

installation and start-up manual.

Installing Dealer/Contractor Responsibilities

Installation

This product is only for use as an optional generator system

which provides an alternate source of electric power and

to serve loads such as heating, refrigeration systems, and

communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience.

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system as

defined by NFPA 70 (NEC).

• Emergency generator systems are intended to

automatically supply illumination, power, or both,

to designated areas and equipment in the event of

failure of the normal supply. Emergency systems may

also provide power for such functions as ventilation

where essential to maintain life, where current

interruption of the normal supply would produce

serious life safety or health hazards.

• Legally Required standby generator systems are

intended to automatically supply power to selected

loads in the event of failure of the normal source

which could create hazards or hamper rescue or fire-

fighting operations.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

Only current licensed electrical and plumbing professionals

should attempt home generator system installations.

Installations must strictly comply with all applicable codes,

industry standards, laws and regulations.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/ recommendations. Smoke alarms

cannot detect carbon monoxide gas.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• Installation must strictly comply with all applicable

codes, industry standards, laws, and regulations.

• Allow sufficient room on all sides of the generator for

maintenance and servicing.

8

After removing the carton, carefully inspect the generator for

any damage that may have occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss or

damage. If loss or damage is noted after delivery, separate

the damaged materials and contact the carrier for claim

procedures. Parts damaged in shipping are not warranted.

Delivery Inspection

The home generator system is supplied with:

• Oil (5W30 Synthetic)

• Flexible steel fuel line

• Installation and start-up manual

• Operator’s manual

• Spare access roof keys

• Spare 15 Amp ATO-type fuse

• Remote wireless monitor

• Antenna

Not included:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables

• Two 60” lengths of 3/4” nominal minimum scheduled

40 steel pipe (NOT conduit)

• Torque screwdriver, 5 to 50 inch-pound range

• Voltage/frequency meter

• Two (2) AA batteries for remote wireless monitor

Shipment Contents

Avoid damage from dropping, bumping, collision, etc. Store

and unpack carton with the proper side up, as noted on the

shipping carton.

Unpacking Precautions

Cold Weather Kit

If operating the generator below 30°F (-1°C), it is HIGHLY

RECOMMENDED that a Model 6231 Cold Weather Kit

(includes oil warmers and battery warmer) be installed.

These items are available at your local servicing dealer.

For cold weather areas (below 0°F (-18°C)) it is also

recommended that a BCI, Size 75, wet lead-acid battery be

used of 630 CCA minimum.

If you need more information on this matter, please call

(888) 575-8226, between 8:00 AM and 5:00 PM CT.

30°F (-1°C)

9

Carbon Monoxide (CO) Detector/ Smoke Detector

Carbon Monoxide (CO) detector(s) installed and in working

order.

Smoke detector(s) installed and in working order.

Placement

Required permits have been obtained.

Generator placed in an area free from Carbon Monoxide

(CO) buildup. See Placement of Standby Generator to

Reduce the Risk of Carbon Monoxide Poisoning.

Generator placed in an area compliant to NFPA 37. See

Placement of Standby Generator to Reduce the Risk of

Fire.

Generator placed in an area free from water damage. See

Other General Location Guidelines.

Generator placed in an area free from utility and other

home systems. See Other General Location Guidelines.

Generator placed in a debris free zone. See Other General

Location Guidelines.

Generator placed on flat ground with provisions for water

drainage.See Other General Location Guidelines.

Fuel

Generator is connected to fuel source with steel flexible

fuel line, has no fuel leaks and conforms to local codes. See

The Gaseous Fuel System.

Proper fuel pressure has been measured with all gas

appliances operating. See The Gaseous Fuel System.

Fuel system has been configured for the proper fuel

supply: Natural gas (NG) or liquefied petroleum ( LP). See

Fuel Conversion.

Fuel type: (circle one) NG LP

Fuel pipe size used: (circle one) 3/4” 1” 1-1/4” 1-1/2”

See NFPA 54.

Fuel pressure at fuel inlet port with generator on and at

full load and all gas appliances turned on and operating

____________________.

Electrical

Generator neutral is connected to Automatic Transfer

Switch. See Generator AC Connection System.

Generator is grounded. See Grounding the Generator and

NFPA 70,NEC.

Generator is connected to the transfer switch with the

specified wiring. See Utility Circuit Connection and

Transfer Switch Communication.

Generator is connected to the transfer switch with the

specified wiring. #18AWG twisted pair wiring from the

generator control panel to the transfer switch is installed

in a separate conduit from high voltage wires unless

the insulation rating on all wiring is rated for 600V See

Transfer Switch Communication.

Dipswitches in most transfer switches must be set to

correspond to the wattage of the generator. See Transfer

Switch Operator/Installation Manual.

Operation

Cold weather kit is installed in temperatures below 40°F

(5°C). See Cold Weather Kit.

Correct battery type is installed and fully charged. See

Final Installation Considerations.

Generator engine oil level is at full mark. See Final

Installation Considerations.

Circuit breaker is in the ON position.

Utility was shut off to test the operation of generator and

transfer switch. Note any fault codes and make corrections

as required.

AC Voltage Output___________________________.

Frequency Output___________________________.

Installation Checklist - GE Home Generator Systems

Proper installation of the home generator requires the completion of the following tasks:

Owner Information

Name: _____________________________________________

Address: ___________________________________________

___________________________________________________

Phone/e-mail: _______________________________________

Unit Information

Generator Model: ____________________________________

Generator Serial Number: _____________________________

Installing Contractor Information

Name: _____________________________________________

Address: ___________________________________________

___________________________________________________

Phone/FAX: _________________________________________

Electrician: _________________________________________

Signature: __________________________________________

Plumber: ___________________________________________

Signature: _________________________________________

Inspector Information

Name: _____________________________________________

Address: ___________________________________________

___________________________________________________

Title: _______________________________________________

Inspection Date: _____________________________________

This generator has been installed per the manufacturer’s

instructions:

Installing Contractor Signature: ______________________________

Date: ____________________________________________________

10

Intentionally Left Blank

11

Generator Placement

Before installing the generator, consult with the homeowner

and convey the following requirements, which must be

satisfied before the installation is complete.

There are two equally important safety concerns in regards

to carbon monoxide poisoning and fire. There are also

several general location guidelines that must all be met

before the installation is considered complete.

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Smoke alarms cannot detect carbon

monoxide gas.

Exhaust Side of the Generator

A

Exhaust outlet side of weatherproof enclosure.

B

Air inlet side of weatherproof enclosure.

A BB

12

Placement of Standby Generator to

REDUCE THE RISK OF CARBON MONOXIDE POISONING

All fossil fuel burning equipment, such as standby

generators, contains carbon monoxide (CO) gas in the engine

exhaust. CO gas is odorless, colorless and tasteless and is

unlikely to be noticed until a person is overcome. CO gas can

kill you so it is required that the following is included as part

of the installation:

• Install generator outdoors in an area that will not

accumulate deadly exhaust gas.

• DO NOT install generator where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building or structure.

• By law it is required in many states to have a Carbon

Monoxide (CO) detector in operating condition in

your home. Carbon monoxide detector(s)

A

MUST

be installed and maintained indoors according to

the manufacturer’s instructions/ recommendations.

A CO monitor is an electronic device that detects

hazardous levels of CO. When there is a buildup of

CO, the monitor will alert the occupants by flashing

visual indicator light and alarm. Smoke alarms cannot

detect CO gas.

• Your neighbor(s) home may be exposed to the engine

exhaust from your standby generator and must be

considered when installing your standby generator.

• Ensure exhaust gas is kept away from:

windows

doors

ventilation intakes

soffit vents

garage doors

crawl spaces or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

A

The arrows in the figure below point to POTENTIAL points of entry for Carbon Monoxide Gas.

B

C

D

E

F

G

13

• DO NOT place standby generator in any area where

leaves or debris normally accumulates. Position

standby generator in an area where winds will carry

the exhaust gas away from any potentially occupied

building or structure.

• Direct the standby generator exhaust away from or

parallel to the building or structure. DO NOT direct the

generator exhaust towards a potentially occupied

building, structure, windows, doors, ventilation intakes,

soffit vents, crawl spaces, open garage doors or other

openings where exhaust gas could accumulate and

enter inside or be drawn into a potentially occupied

building or structure.

ENGINE

EXHAUST

STANDBY

GENERATOR

14

Structure

Center of Exhaust Panel

Standby

Exhaust

Direction

5 ft (1.5 m)

B

C

Placement of Standby Generator to REDUCE THE RISK OF FIRE

Examples of standby generator locations to reduce the

risk of fire:

The National Fire Protection Association (NFPA) standard

NFPA 37 establishes criteria for minimizing the hazard

of fire during the installation and operation of stationary

combustion engines. NFPA 37 limits the spacing of an

enclosed generator from openings in walls, structures and

combustible materials outside the enclosure.

The placement requirements provided are based on

compliance to NFPA 37 2010 section 4.1.4 and a full-scale

demonstration fire test. Details of compliance testing can be

found in section National Fire Protection Association (NFPA)

standard NFPA 37 requirements and testing.

A

Standby weatherproof enclosure must be at least 5 ft

(1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

B

Exhaust outlet side of weatherproof enclosure must

have at least 5 ft (1.5 m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

C

Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from

any structure, overhang or trees.

Standby Weatherproof enclosure must have a

minimum of 18 inches (45.7 cm) clearance from any

structures with or without a fire rating.

NOTICE DO NOT place weatherproof enclosure under a deck

or other type of covered structure that may confine airflow.

Vertical Clearances

Legend for Generator Locations to reduce the risk of fire.

WARNING

Exhaust heat/gases could ignite combustibles

or structures resulting in death, serious injury and/or

property damage.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft. (1.5 m) minimum clearance from any structure, shrubs, trees

or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft. (1.5 m) from windows, doors, any wall opening, shrubs or

vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a minimum

of 5 ft. (1.5 m) overhead clearance from any structure, overhang

or trees.

• DO NOT place weatherproof enclosure under a deck or other type

of structure that may confine airflow.

• Use only flexible steel fuel line provided. Connect provided fuel line

to generator, DO NOT use with or substitute any other flexible fuel

line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/recommendations.

Carbon monoxide alarms cannot detect smoke.

• DO NOT place weatherproof enclosure in manner other than

shown in illustrations.

D

15

A

Standby weatherproof enclosure must be at least 5 ft

(1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

B

Exhaust outlet side of weatherproof enclosure must

have at least 5 ft (1.5 m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

C

Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from

any structure, overhang or trees.

NOTICE DO NOT place weatherproof enclosure under a deck

or other type of covered structure that may confine airflow.

18 in (45.7 cm) min

Standby

Exhaust

Direction

A

B

Standby

Exhaust

Direction

A

B

5 ft (1.5 m) min

Standby

Exhaust

Direction

5 ft (1.5 m)

A A

B

Standby

Exhaust

Direction

A

B

Generator Installations

5 ft

(1.5 m)

5 ft (1.5 m) min

18 in (45.7 cm) min

5 ft

(1.5 m)

5 ft (1.5 m) min

18 in (45.7 cm) min

5 ft (1.5 m)

D

D D

DD

Standby Weatherproof enclosure must have a

minimum of 18 inches (45.7 cm) clearance from any

structures with or without a fire rating.

NOTICE The gures below show the minimum installation distances allowed to structures and items in the legend.

16

Requirements:

NFPA 37 2010, section 4. 1. 4, Engines Located Outdoors.

Engines, and their weatherproof housings if provided, that

are installed outdoors shall be located at least 1.5m (5 ft)

from openings in walls and at least 1.5 m (5 ft) from structures

having combustible walls. A minimum separation shall not be

required where either of the following conditions exist:

1. The adjacent wall of the structure has a fire resistance

rating of at least 1 hour.

2. The weatherproof enclosure is constructed

of noncombustible materials and it has been

demonstrated that a fire within the enclosure will not

ignite combustible materials outside the enclosure. *

Annex A Explanatory Material

A.4.1.4 (2) Means of demonstrating compliance are by means

of full-scale fire tests or by calculation procedures, such as

those given in NFPA 555, Guide on Methods for Evaluating

Potential for Room Flashover.

To comply with condition 2, the weatherproof enclosure has

been constructed completely of non-combustible materials

and full-scale fire tests have been conducted to demonstrate

that a fire within the enclosure will not ignite combustible

materials outside the enclosure.

National Fire Protection Association (NFPA) Standard NFPA 37 Requirements and Testing

• Place the standby generator in a prepared location

that is flat and has provisions for water drainage.

• Install the standby generator in a location where

sump pump discharge, rain gutter down spouts, roof

run-off, landscape irrigation, or water sprinklers will

not flood the unit or spray the enclosure and enter

any air inlet or outlet openings.

• Install the standby generator where it will not affect or

obstruct any services (including covered, concealed

and underground), such as telephone, electric, fuel

(natural gas / LPG vapor), irrigation, air conditioning,

cable, septic, sewer, well and so forth.

• Install the standby generator where leaves, grass,

snow, etc will not obstruct air inlet and outlet

openings. If prevailing winds will cause blowing or

drifting, you may need to construct a windbreak to

protect the unit.

Other General Location Guidelines

17

Electrical and Fuel Inlet Locations

The 3/4 inch N.P.T. fuel inlet connector

A

and electrical inlet

location

B

is shown below.

A ½ inch knock-out is provided for the electrical inlet. This

inlet may be enlarged or supplemented to accommodate

a maximum conduit size of 1 ½ inches. Ensure that the

installed conduit(s) enter the unit in the zone shown in the

drawing such that they properly enter the electrical box and

do not interfere with the fully opened roof.

A

B

The home generator is supplied with a base that, unless

mandated by local code, does not require a concrete slab.

18

Lifting the Generator

The generator weighs more than 500 pounds (227 kg). Proper

tools, equipment and qualified personnel should be used in

all phases of handling and moving the generator.

Two 60” lengths of 3/4” nominal minimum scheduled 40

steel pipe

A

, supplied by the installer, are required to lift the

generator manually. Insert pipes through the lifting holes

B

located near the unit’s base.

You may also lift the unit using a “hook and hoist” method

attached to the lifting pipes, provided that you use a

spreader bar to ensure that the chains or cables DO NOT

touch the generator’s roof.

WARNING Hazardous Voltage - Contact with power lines could

cause electric shock or burn, resulting in death or

serious injury.Lifting Hazard / Heavy Object - Could

result in serious injury.

• If lifting or hoisting equipment is used, DO NOT contact any

power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the Generator.

• DO NOT lift unit by roof as damage to generator will occur.

In areas determined to be hurricane prone, it is

recommended to anchor the standby generator to concrete.

The concrete anchors must be rated to hold 800 lbs ( kg).

There are four 7/16 inch hole locations around the base

of generator in which to anchor the unit.

Concrete Anchoring of Unit

A

B

C

NOTICE Unless mandated by local or state code, a concrete

slab is not required.

19

Each generator is shipped with a set of identical keys. These

keys fit in the lock on the front removable panel. The roof

must be unlocked in order for it to open.

Access Panels

The generator is equipped with an enclosure that has several

access panels, as shown.

The access panels and the components located behind them

are listed below:

A - Roof (Control Panel, air filter, oil dipstick, and circuit

breaker)

B - Front Access Panel (oil drain and oil filter)

D - Battery Panel (battery and generator data label)

E - Rear Access Panel (fuel regulator, fuel selector, and

engine starter)

F - Control Panel Cover (field wiring and control wires)

B

A

B

C

D

E

D

E

B

20

To open roof:

1. Insert key into lock of front panel. Gently push

down on roof above the lock to aid in turning the key.

Turn key one quarter turn clockwise.

2. Lift roof to the open position.

To remove front panel:

1. Remove the two bolts that secure the panel to the

unit.

2. Lift panel to remove from unit.

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

To remove rear panel:

1. Ensure the roof is in the open position.

2. Remove the two bolts that secure the panel to the

unit.

3. Lift panel to remove from unit.

To secure rear panel:

1. Slide panel into place on unit.

2. Secure the panel with two bolts.

To remove battery panel:

1. Ensure the roof is in the open position.

2. Remove the two bolts that secure the panel to the

unit.

3. Lift up on panel and remove.

To secure battery panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

A

B

C

D

A

B

C

D

La page charge ...

Simplicity 040381-01 Guide d'installation

Simplicity 040381-01 Guide d'installation

dans d''autres langues

Documents connexes