Mode d'Emploi P Smart Guide de démarrage rapide

FIG-LX1

Quick Start Guide

Guide de démarrage rapide

Schnellstartanleitung

Guida di avvio rapido

Guía de inicio rápido

Guia de Início Rápido

Snelstartgids

Contents

English (United Kingdom)............................................... 1

Français........................................................................ 12

Deutsch.........................................................................25

Italiano......................................................................... 37

Español.........................................................................48

Português..................................................................... 60

Nederlands................................................................... 71

i

Your device at a glance

Before you start, let's take a look at your new device.

l To power on your device, press and hold the power button

until the screen turns on.

l To power off your device, press and hold the power button,

and then touch .

1

2

3

4

5

7

8

9

10

11

12

6

13

14

NFC

Rear camera Status indicator

Front camera Earpiece

Headset jack Primary microphone

Micro-USB port Speaker

Power button Volume button

Light sensor Fingerprint scanner

Flash Secondary microphone

l Press and hold the power button to force your device

to restart.

English (United Kingdom)

1

Getting Started

Follow the instructions in the following ﬁgures to set up your

device.

NJDSP4%

l Do not insert or remove the SIM card when your device

is powered on.

l Ensure that the card is correctly aligned and that the

card tray is level when you insert it into your device.

Be careful not to scratch your device or hurt yourself

when using the eject pin. Store the eject pin out of the

reach of children to prevent accidental swallowing or

injury.

Do not use cut or modiﬁed SIM or microSD cards with

your device as these may not be recognised and could

damage the card tray (slot).

2

Dual Card Dual Standby Single

Pass

Your device supports only dual card dual standby single pass,

which means you cannot use both SIM cards for calls or data

services simultaneously.

l When you are on a call using SIM card 1, SIM card 2 cannot

be used to make or answer calls. If someone calls SIM card

2, the caller will hear a voice message similar to "The

subscriber you dialled is out of the service area" or "The

subscriber you dialled cannot be connected for the

moment, please try again later." The actual message will

vary by service provider.

l When you are using SIM card 1's data service, SIM card 2's

data service will be disabled.

Your device's single pass feature helps reduce power

consumption and increase your device's standby time. It is not

related to your service provider's network conditions.

It may be a good idea to contact your service provider and

subscribe to missed call reminder and related assistance

services to avoid the conﬂicts mentioned above.

3

For more information

If you encounter any problems whilst using your device, you

can get help from the following resources:

l Visit http://consumer.huawei.com/en to view device

information, frequently asked questions and other

information.

l Visit http://consumer.huawei.com/en/support for the most

up-to-date contact information for your country or region.

l You can ﬁnd service hotlines, retailer addresses, service

policies and more information for your local region in

HiCare.

Go to Settings and touch System > About phone > Legal to

view legal information for your product.

Go to Settings and touch System > About phone > Legal >

Safety information to view safety information for your

product.

Go to Settings and touch System > About phone >

Authentication info to view regulatory information for your

product.

Go to Settings and touch System > Certiﬁcation logos to

view more information on certiﬁcation logos for your product.

All pictures and illustrations in this guide, including but

not limited to the product color, size, and display content,

are for your reference only. The actual product may vary.

Nothing in this guide constitutes a warranty of any kind,

express or implied.

4

Safety Information

Please read all of the safety information carefully before using

your device to ensure its safe and proper operation and to

learn how to dispose of your device properly.

Operation and Safety

l To prevent possible hearing damage, do not

listen at high volume levels for long periods.

l Using an unapproved or incompatible power adapter,

charger or battery may damage your device, shorten its

lifespan or cause a ﬁre, explosion or other hazards.

l Ideal operating temperatures are 0 °C to 35 °C. Ideal

storage temperatures are -20 °C to +45 °C.

l Pacemaker manufacturers recommend maintaining a

minimum distance of 15 cm between a pacemaker and a

wireless device to prevent potential interference with the

pacemaker. If using a pacemaker, hold the device on the

side opposite the pacemaker and do not carry the device in

your front pocket.

l Keep the device and the battery away from excessive heat

and direct sunlight. Do not place them on or in heating

devices, such as microwave ovens, stoves or radiators.

l Adhere to local laws and regulations while using the device.

To reduce the risk of accidents, do not use your device

while driving.

l While ﬂying in an aircraft or immediately before boarding,

ensure that you use your device according to the

instructions provided. Using a wireless device in an aircraft

may disrupt wireless networks, present a hazard to aircraft

operations or be illegal under law.

l To prevent damage to your device's parts or internal

circuits, do not use it in dusty, smoky, damp or dirty

environments or near magnetic ﬁelds.

l When charging the device, make sure the power adapter is

plugged into a socket near the devices and is easily

accessible.

l Unplug the charger from the electric socket and from the

device when not in use.

l Do not use, store or transport the device where ﬂammables

or explosives are stored (e.g. in a petrol station, oil depot or

5

chemical plant). Using your device in these environments

increases the risk of explosion or ﬁre.

l Dispose of this device, the battery and accessories

according to local regulations. They should not be disposed

of in normal household waste. Improper battery use may

lead to ﬁre, explosion or other hazards.

l Please consult your doctor and the device manufacturer to

determine if operation of your device may interfere with the

operation of your medical device.

l Adhere to any rules or regulations set forth by hospitals and

health care facilities.

l If you must make or answer a call, stop your vehicle at a

safe location ﬁrst.

l Keep the device away from sources of heat and ﬁre, such as

a heater, microwave oven, stove, water heater, radiator, or

candle.

Potentially Explosive Atmosphere

Power off your device in any area with a potentially explosive

atmosphere, and comply with all signs and instructions. Areas

that may have potentially explosive atmospheres include the

areas where you would normally be advised to turn off your

vehicle engine. Triggering of sparks in such areas could cause

an explosion or a ﬁre, resulting in bodily injuries or even

deaths. Do not power on your device at refueling points such

as service stations. Comply with restrictions on the use of radio

equipment in fuel depots, storage, and distribution areas, and

chemical plants. In addition, adhere to restrictions in areas

where blasting operations are in progress. Before using the

device, watch out for areas that have potentially explosive

atmospheres that are often, but not always, clearly marked.

Such locations include areas below the deck on boats,

chemical transfer or storage facilities, and areas where the air

contains chemicals or particles such as grain, dust, or metal

powders. Ask the manufacturers of vehicles using liqueﬁed

petroleum gas (such as propane or butane) whether this device

can be safely used in their vicinity.

Disposal and recycling information

The crossed-out wheelie bin symbol on your product, battery,

literature or packaging reminds you that all electronic products

6

and batteries must be taken to separate waste collection

points at the end of their working lives; they must not be

disposed of in normal household waste. It is the responsibility

of the user to dispose of the equipment using a designated

collection point or service for separate recycling of waste

electrical and electronic equipment (WEEE) and batteries

according to local laws.

Proper collection and recycling of your equipment helps ensure

EEE waste is recycled in a manner that conserves valuable

materials and protects human health and the environment.

Improper handling, accidental breakage, damage, and/or

improper recycling at the end of its life may be harmful for

your health and the environment. For more information about

where and how to drop off your EEE waste, please contact

your local authorities, retailer or household waste disposal

service or visit the website http://consumer.huawei.com/en/.

Reduction of hazardous substances

This device and any electrical accessories are compliant with

local applicable rules on the restriction of the use of certain

hazardous substances in electrical and electronic equipment,

such as EU REACH, RoHS and Batteries (where included)

regulations, etc. For declarations of conformity about REACH

and RoHS, please visit our web site http://

consumer.huawei.com/certiﬁcation.

EU Regulatory Conformance

Body worn operation

The device complies with RF speciﬁcations when used near

your ear or at a distance of 0.50 cm from your body. Ensure

that the device accessories, such as a device case and device

holster, are not composed of metal components. Keep the

device away from your body to meet the distance requirement.

The highest SAR value reported for this device type when

tested at the ear is

FIG-LX1 1.27 W/kg

And when properly worn on the body is

FIG-LX1 0.99 W/kg

Statement

Hereby, Huawei Technologies Co., Ltd. declares that this device

is in compliance with the essential requirements and other

relevant provisions of Directive 2014/53/EU.

The most recent and valid version of the DoC (Declaration of

Conformity) can be viewed at http://consumer.huawei.com/

certiﬁcation.

7

This device may be operated in all member states of the EU.

Observe national and local regulations where the device is

used.

This device may be restricted for use, depending on the local

network.

Restrictions in the 2.4 GHz band:

Norway: This subsection does not apply for the geographical

area within a radius of 20 km from the centre of Ny-Ålesund.

Frequency Bands and Power

(a) Frequency bands in which the radio equipment operates:

Some bands may not be available in all countries or all areas.

Please contact the local network provider for more details.

(b) Maximum radio-frequency power transmitted in the

frequency bands in which the radio equipment operates: The

maximum power for all bands is less than the highest limit

value speciﬁed in the related Harmonised Standard.

The frequency bands and transmitting power (radiated and/or

conducted) nominal limits applicable to this radio equipment

are as follows:

FIG-LX1 GSM900: 37 dBm, GSM1800: 34 dBm,

WCDMA900/2100: 25.7 dBm, LTE Band

1/3/7/8/20: 25.7 dBm, Wi-Fi 2.4G: 20 dBm,

Bluetooth: 20 dBm,NFC: 60 dBuA/m at 10m

Accessories and Software Information

Some accessories are optional in certain countries or regions.

Optional accessories can be purchased from a licenced vendor

as required. The following accessories are recommended:

Adapters: HW-050200X01 (X represents the different plug

types used, which can be either C, U, J, E, B, A, I, R, Z or K,

depending on your region)

Batteries: HB366481ECW-11

Earphones: MEMD1532B528A00, HA1-3W,

1293-3283-3.5mm-300, EPAB542-2WH03-DH

The product software version is FIG-LX1: FIG-LX1

8.0.0.100(C900). Software updates will be released by the

manufacturer to ﬁx bugs or enhance functions after the

product has been released. All software versions released by

the manufacturer have been veriﬁed and are still compliant

with the related rules.

All RF parameters (for example, frequency range and output

power) are not accessible to the user, and cannot be changed

by the user.

8

For the most recent information about accessories and

software, please see the DoC (Declaration of Conformity) at

http://consumer.huawei.com/certiﬁcation.

FCC Regulatory Compliance

Body worn operation

The device complies with RF speciﬁcations when used near

your ear or at a distance of 1.50 cm from your body. Ensure

that the device accessories, such as a device case and device

holster, are not composed of metal components. Keep the

device away from your body to meet the distance requirement.

Certiﬁcation information (SAR)

This device is also designed to meet the requirements for

exposure to radio waves established by the Federal

Communications Commission (USA).

The SAR limit adopted by the USA is 1.6 W/kg averaged over

one gram of tissue. The highest SAR value reported to the FCC

for this device type complies with this limit.

The highest SAR value reported to the FCC for this device type

when using it at the ear is

FIG-LX1 0.93 W/kg

And when properly worn on the body is

FIG-LX1 0.75 W/kg

And when using the Wi-Fi hotspot function is

FIG-LX1 0.67 W/kg

FCC statement

This device has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This device generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

device does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to perform one or more of

the following operations to try to correct the interference:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the device into an outlet on a circuit different from

that to which the receiver is connected.

9

--Consult the dealer or an experienced radio/TV technician for

help.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

Caution: Any changes or modiﬁcations to this device not

expressly approved by Huawei Technologies Co., Ltd. for

compliance could void the user's authority to operate the

device.

10

Legal Notice

Trademarks and Permissions

, , and are trademarks or registered

trademarks of Huawei Technologies Co., Ltd.

Android™ is a trademark of Google Inc.

LTE is a trade mark of ETSI.

The Bluetooth

®

word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of such

marks by Huawei Technologies Co., Ltd. is under license.

Wi-Fi

®

, the Wi-Fi CERTIFIED logo and the Wi-Fi logo are

trademarks of Wi-Fi Alliance.

Privacy Policy

To better understand how we protect your personal

information, please see the privacy policy at http://

consumer.huawei.com/privacy-policy.

THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND

DOES NOT CONSTITUTE ANY KIND OF WARRANTIES.

11

Votre appareil en un coup d’œil

Avant de commencer, jetons un coup d’œil à votre nouvel

appareil.

l Pour mettre votre appareil sous tension, appuyez

longuement sur le bouton alimentation jusqu’à ce que

l’écran s’allume.

l Pour mettre votre appareil hors tension, appuyez

longuement sur le bouton d’alimentation, puis touchez

.

1

2

3

4

5

7

8

9

10

11

12

6

13

14

NFC

Appareil photo arrière

Témoin lumineux

d'état

Appareil photo avant Écouteur

Prise casque Micro principal

Port micro-USB Haut-parleur

Bouton marche/arrêt Bouton du volume

Capteur de luminosité

Capteur d'empreinte

digitale

Flash Micro secondaire

Français

12

l Appuyez longuement sur le bouton d’alimentation

pour forcer le redémarrage.

13

Prise en main

Pour conﬁgurer votre appareil, suivez les instructions

présentées sur les illustrations suivantes.

NJDSP4%

l Ne pas insérer ou retirer le tiroir de carte lorsque votre

appareil est sous tension.

l Assurez-vous que la carte est correctement orientée et

maintenez le tiroir de carte à plat lors de son insertion

dans votre appareil.

Faites attention de ne pas éraﬂer votre appareil ou de ne

pas vous blesser en utilisant l’épingle d’éjection du tiroir

de cartes. Rangez la broche d’éjection de carte hors de la

portée des enfants pour éviter toute ingestion ou blessure

accidentelle.

N'utilisez pas des cartes SIM ou micro SD coupées ou

modiﬁées avec votre appareil car elles pourraient ne pas

être reconnues, ou endommager le tiroir (emplacement)

de la carte.

14

Double carte double veille accès

unique

Votre appareil prend uniquement en charge le mode double

carte double veille simple passe, qui implique que vous ne

pouvez utiliser les deux cartes SIM simultanément que pour les

appels ou les services de données.

l Quand vous appelez via la carte SIM 1, la carte SIM 2 ne

peut être utilisée pour appeler ou répondre à des appels. Si

quelqu’un appelle via la carte SIM 2, il entendra un message

vocal tel que « L’abonné contacté est hors de la zone de

service » ou « Cet abonné n’est pas en mesure de vous

répondre pour le moment ; veuillez réessayer plus tard ». Le

message variera d’un fournisseur à l’autre.

l Quand vous utilisez le service de données de la carte SIM 1,

le service de données de la carte SIM 2 sera désactivé.

La fonctionnalité simple passe de votre appareil vous aide à

réduire sa consommation d'énergie et à augmenter sa durée

de veille. Elle n’est pas liée aux conditions de réseau de votre

fournisseur de services.

Nous vous recommandons de contacter votre prestataire de

service et de souscrire à un service de rappel d’appels manqués

et aux services d’assistance correspondant pour éviter les

conﬂits évoqués ci-dessus.

15

Informations supplémentaires

Si vous rencontrez des problèmes lorsque vous utilisez votre

téléphone, vous pouvez obtenir de l’aide à partir des

ressources suivantes :

l Visitez http://consumer.huawei.com/fr pour consulter les

informations sur l'appareil, les questions fréquentes et

autres informations.

l Vous rendre sur le site http://consumer.huawei.com/fr/

support pour connaître les coordonnées de contact les plus

récentes pour votre pays ou région.

l Vous pouvez trouver les services d'assistance téléphonique,

les adresses des points de vente, la politique de service et

plus d'informations pour votre région dans HiCare.

Accédez à Paramètres puis touchez Système > À propos du

téléphone > Légal pour consulter les informations juridiques

relatives à votre produit.

Accédez à Paramètres puis touchez Système > À propos du

téléphone > Légal > Informations de sécurité pour

consulter les informations de sécurité relatives à votre produit.

Accédez à Paramètres puis touchez Système > À propos du

téléphone > Information d'authentiﬁcation pour consulter

les informations réglementaires relatives à votre produit.

Accédez à Paramètres puis touchez Système > Logos de

certiﬁcation pour plus d’informations relatives aux marques

de certiﬁcations pour votre produit.

Toutes les images et illustrations de ce guide (y compris,

mais sans s’y limiter, la couleur, la taille et le contenu

d’afﬁchage du téléphone) sont uniquement fournies à

titre de référence. Le produit réel peut s’avérer différent.

Ce guide ne contient aucun élément constituant une

garantie quelle qu’elle soit, explicite ou implicite.

16

La page charge ...

Mode d'Emploi P Smart Guide de démarrage rapide

Mode d'Emploi P Smart Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents